Search Documents

By R. W. Thompkins

"PREFACEPart 1 of this paper, published in the September issue, covered the occurrence of uranium, radiation from uranium ores, the uranium series, radioactive theory, radioactive equilibrium and application to the radon series, the working level, the theory of emanation and diffusion, transport by thermal diffusion of radon emanating from porous rocks, and definitions.This Part 2, which follows, deals with radiation theory applied to uranium ores, other radon migration factors, factors affecting the radon gas release rate, the measurement of radon gas emanation rates, the tunnel concept, variation of emanation rate with grade and estimating radioactivity from grade analysis.The series will conclude with Part 3, in the November issue, which will discuss the techniques for controlling radiation and provide some example calculations.10.0. Radiation Theory Applied to Uranium Ores10.0.1. The processes of diffusion transport of radon gas, through rock from the fundamental physics is a function o f the radon gas concentration in the interstitial pore spaces and the distance from the surface. Expressed by Fick's first law of diffusion, it is expressed: [ ]10.0.2. The maximum concentration is a function of the emanating power (ß), thus the above equation may be expressed: [ ]10.1. The Effect of Porosity10.1.1. If a constant emanating power is assumed (ß), a family of curves can be obtained for concentrations at varying distances and rock porosities. The curves as originally plotted assumed a constant emanating power of 5 x 10-4 pico curies/litre/sec and show the maximum expected concentrations in the pores in pico curies per litre. Because these concentrations are proportioned to the emanating power, this set of curves can be structured to show the fraction of maximum concentrations possible at various porosities of the rock.10.1.2. Notice that at 10, 20 and 30% porosities a 5-cm sample (hand-sized and drill-sized pieces) has no practical increase in pore concentration. Thus, by measuring the emanating power of hand-sized pieces of ore, the actual radon gas production into any pile of broken ore could be estimated readily."

Jan 1, 1982

By P. L. Claessens, S. Belisle, C. Bowen

"Use of zinc shot feed is a well-established procedure among North American electro-galvanizers. This form of zinc is easy to handle and relatively inexpensive when compared with zinc oxide. This paper reports results on the kinetics of zinc shot dissolution in traditional pure zinc solutions and in electrolytes used for the plating of nickel/zinc alloys. Despite the cementation of minor amounts of nickel in the latter solution, acceptable dissolution rates of the zinc shot can be achieved through proper adjustment of the solution velocity. Under these conditions, the nickel shell produced by cementation is continuously abraded, exposing the underlying zinc.IntroductionThe use of insoluble, noble metal-containing anodes rather than soluble zinc anodes for the operation of high current density electro-galvanizing lines has gained almost universal acceptance. Two major reasons for this trend are:• improved control of the process by virtue of constant inter-electrode distance; and• increased productivity because the operation of the lines does not require the relatively frequent interruptions for replacement of consumed anodes .The results of the principal anode and cathode reactions are, respectively, depletion of the zinc content of the electrolyte and the increase on its acidity;"

Jan 1, 1991

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By J. H. Archibald

"In mines employing cut-and-fill stoping (sand fill), ore passes are built as mining progresses upward. These ore pass raises are generally made from timber and form a vertical ""chimney"", like a very tall log cabin. Traditionally the chimney, or raise, is square in shape and is constructed from square timbers with stepped ends as shown in Figure I. The timbered raise is thus surrounded by sandfill on its outside, leaving the centre open for passing ore down through it. Each layer consists of four timbers and rests flush on the layer below. The corners are frequently pinned or spiked.Under certain conditions in sandfilled stopes large horizontal loads may be transmined to the raise cribbing timbers, or the ""chimney's"" walls. In deep mines, where rock bursts are a problem, it can be shown that one of the conditions for rockbursts to occur is that the burst zone be stiffer and weaker than the surrounding rock(l). This allows a strain energy build-Up in the rock surrounding the burst zone, and the rate of release of this strain energy is known to be related directly to the over-all strength and stiffness of the rock in the burst zone. In stopes that are sandfilled, attempts are, therefore, usually made to increase the strength of the sandfill by the addition of large-sized waste rock and Portland cement. These measures usually achieve the desired strength of the sandfill and, consequently, the severity and frequency of rockbursts can be reduced.Problems may arise when the now chunky sandfill transmits high loads to the raise cribbing along with relatively large move- merits. This leads to heavily stressed and strained cribbing timbers the Coeur d'Alene district in Idaho, raise cribbing failures are common. A typical mode of cribbing failure is shown in Figure 2. One learns in statics that a structure shaped like the crib in Figure I is inherently unstable , at least from a structural standpoint. The crib has pivoted, in Figure 2, into a rhombi c shape and supports very little load. Soon the four-foot square raise cribbing made from 5 in. by 5 in. timbers will no longer pass ore."

Jan 1, 1991

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"Abstract - The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3 and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By H. L. Gibson, T. N. Setterfield, J. J. Watkins, R. W. Hodder

"The McDougall-Despina fault set in the Noranda district of northwestern Quebec defines the eastern margin of the Despina cauldron, nested within the district-scale Noranda cauldron. The faults are stratabound in that they displace stratigraphy of the cauldron fill, but do not off-set the cauldron cover. The faults are occupied by dikes that acted as eruptive centers to volcanic members of the cauldron-filling sequence. Measurable displacement across the McDougall-Despina fault set is greater than 750 m, and coincident with post-cauldron volcanism. Feeder dikes cross-cut each other and are typically depleted in Na2O and CaO, and enriched in MgO, K2O, Fe2O3and MnO relative to fresh flows. Economic and subeconomic massive sulfide deposits occur adjacent to the McDougall-Despina fault set at different levels over a stratigraphic thickness of 3000 m. These include the Corbet deposit, the subeconomic D-68 Zone deposits, and the subeconomic stringer zones of South Rusty Hill and Bedford Hill. Numerous copper occurrences and abundant hydrothermal alteration occur in and immediately adjacent to the fault set.The McDougall, Despina, and adjacent, parallel, ancillary faults define a synvolcanic fault set which controlled the location of magmatism, hydrothermal alteration and mineral deposition during the early evolution of the Noranda cauldron. Significant sulfide mineral deposition commonly occurred in proximity to the intersection of the McDougall-Despina fault set with northeast-trending synvolcanic faults. Recognition of synvolcanic faults is therefore a major objective of exploration programs for volcanic-associated massive sulfide deposits."

Jan 1, 1995

By Osamu Inoue, Takashi Yamashita, Takashi Ikemoto

The expansion project in Naoshima smelter and refinery to meet enhancing recycling business of E-scrap was successfully completed in 2016 to have a capacity of 110,000 tpa of E-scrap treatment. Increasing treatment of E-scrap has raised the Ni content of copper anode to 4000 ppm on average, which is double the level of 10 years ago, and to 6000 ppm or more occasionally. The tank house has refined such copper anode to copper cathode with starter sheets. Since most Ni in Copper anode dissolves in copper electrolyte, the Ni content of the electrolyte has increased to 27 g/L and more. Ni accumulated in the electrolyte has increased power consumption during the electrolytic refining of copper, although cathode quality has been controlled satisfactory so far. In order to ensure sustainable operation while growing E- scrap business, the NiSO4 process has been expanded recently so as to recover Ni in the electrolyte more and the pressurized-leaching technology will be introduced to the slime leaching process so as to enhance the capacity of slime treatment and to improve Ni recovery in the near future. INTRODUCTION In recent years, the treatment amount of E-scrap at Naoshima smelter and refinery has increased according to the growth of its recycling business as shown in Figure 1, while impurities from E-scrap have concentrated in copper anode as well. Especially, Ni content in anode has been increasing remarkably since 2012, causing to raise Ni content in the electrolyte as shown in Figure 2. The increment of Ni content in copper anode and electrolyte has adversely affected the electrorefining process, slime leaching process, and NiSO4 crystallization process at the tank house. Such severe conditions provided opportunities to redesign the tank house to establish a robust process to which more Ni is acceptable.

Jan 1, 2019

By J. G. Schofield, C. G. Tan, R. J. Ord

"Most electric furnaces in the nickel and copper smelting industries are still fitted with conventional electrode holders which consist of water-cooled electrical contact clamps and a pressure ring. The water cooling exerts a significant cooling effect on the electrode column. The importance of controlling the temperature of the Soderberg electrode paste at the contact clamp area is examined, using in-plant experience and computer simulation of the paste melting and baking process. In addition to the effect of water-cooling, the effect of other variables, including the mantle air temperature, the electrode current, the furnace freeboard temperature and the electrode slipping rate are discussed. Ways in which the variable heating conditions in the paste melting zone can be controlled are outlined.IntroductionIn most non-ferrous electric smelting operations, the breakage of Soderberg electrodes is an infrequent, isolated occurrence. Occasionally, however, a rash of breakages may be experienced on a particular furnace for what appears to be no obvious reasons. The extent of the breaks may not exhibit a uniform pattern; sometimes the break may be less than half a metre above the electrode tip; at other times it may be at or just below the roof level. The latter type of break is, of course, the most dangerous since it is closest to the non-baked, weak portion of the electrode paste column. No matter where the breaks occur, they result in abnormal furnace power, charging and tapping conditions and loss of production while the new electrode section is slipped and baked. On a six-electrode furnace, breakage on one electrode has the immediate effect of reducing the total furnace power by one-third. On a three-electrode furnace, the effect is more drastic, one half of the power being lost."

Jan 1, 1995

By Bruce Peberdy

Outline ?Building Systems ?Climatic Effects ?Thermal Effects ?Building Components ?Building Materials ?Structural Deterioration ?Maintenance Considerations

Nov 1, 2011

By D. M. Maijer, S. L. Cockcroft, A. B. Phillion, P. Fan, C. Reilly, H. Khadivinassab

A combined experimental / numerical approach is proposed to investigate the bulk transfer of solute due to liquid metal feeding during shape casting of aluminum alloy A356 (Al-7Si-0.3Mg). A dumbbell-shaped experimental casting geometry has been developed, which promotes solute redistribution due to liquid metal feeding. The redistribution of solute in trial castings is evaluated based on the area fraction of eutectic phases. In the numerical model, silicon species segregation during solidification are calculated assuming the Scheil approximation, and are coupled with macro-scale solute transport due to Darcy flow in the mushy zone and feeding flow. The model has been implemented within the commercial CFD software, FLUENT, which simultaneously solves the thermal, fluid flow fields and species segregation on the macro-scale. The experimental and numerical results are compared and contrasted to examine the effects of liquid metal feeding in this casting.

Jan 1, 2014

Agenda ?Introduction ?Geology ?Mining ?Metallurgy ?Process, Layout ?Environmental Background ?Kinross Gold Corporation owns the Lobo-Marte gold property, located in Region III of northern Chile. ?The property is close to two other Kinross mines, Maricunga 50kmto the south and La Coipa 60km to the north, plus a regional office in Copiapo and district level operating synergies are expected. ?Lobo and Marte were discovered in the early 1980s and are intrusion-hosted, porphyry-type precious metal deposits, typical of the Maricunga District. ?The Marte open pit heap leach mine was in commercial production in late 1988, but was suspended in February 1992 as it did not meet forecasted production levels and recoveries. ?Kinross plans to recover ore from the Lobo and Marte deposits through an open-pit, heap leach47,000tonne per day operation.

May 1, 2010

By M. S. Greenfield, E. Cocchiarella, S. Chubbs

"At Dofasco sNo.4furnace a variation of the basic oxygen steelmaking process, Klockner Oxygen Bottom Maxhutte (K-OBM), is used to produce steel. Large amounts of hot gases and particulate are evolved during the oxygen blowing phase. A quencher and a venturi scrubber are used to collect over 99.5% of the particulate. In 1990, the authors investigated the effect of foamy slag on the particulate emissions from the furnace. The amount of lime added early in the oxygen blowing cycle was reduced, making the slag more viscous and foamy for a six minute period. Instantaneous particulate emissions were monitored throughout the blow by analyzing quencher and venturi scrubber water samples. Particulate emissions were reduced up to 59% during the foamy slag period.IntroductionThe reduction of the amount of waste generated or control of emissions at source is at the top of the ""3R"" hierarchy of waste management (Reduce, Reuse, Recycle). Process and operating practice changes are often the most economical ways to control emissions. At Dofasco, they investigated the effect of operating practice changes, specifically the formation of a foamy slag, on particulate emissions from steelmaking furnaces. They wanted to determine if a foamy slag changed the quantity and nature of the fume evolved from the K-OBM furnace over the oxygen blowing phase.The Basic Oxygen Steelmaking ProcessesThe basic oxygen steelmaking process (BOP) generates large quantities of very fine metal oxide fume during the production of steel. In this process, scrap steel and molten iron (hot metal) from blast furnaces are charged into a steelmaking furnace. Then pure oxygen is injected and a lime flux added . The oxygen reacts with carbon dissolved in the molten iron to form carbon monoxide. Oxygen lances can have secondary nozzles which introduce oxygen above the bath. This secondary oxygen, known as post-combustion, bums some of the carbon monoxide radiating the heat back to the bath. Particulate and gases rich in carbon monoxide are ejected from the furnace during the oxygen blowing phase and are collected by a gas cleaning system. Typically, more than 99.5010 of the particulate is scrubbed from the gases by high energy venturi scrubbers or electrostatic precipitators. The oxide sludge or dust collected may have elevated zinc and lead which is unsuitable for recycle to blast furnaces. Due to the presence of these undesirable elements, treatment and disposal of steelmaking oxide dust is difficult and costly."

Jan 1, 1993

By Raja V. Ramani, Sukumar Bandopadhyay

"The dispersion of diesel contaminants into the mine atmosphere is a variant of general class of diffusion-dilution problems relevant to underground mining practice. The equipment operations in underground mining are characterized by different activities with different time duration s, i.e. varying duty cycles. Therefore the volume and quality of diesel emissions and consequently, instantaneous concentrations are quite variable. Design of mine ventilation systems under these conditions becomes complex. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport in the design of ventilation system are discussed.IntroductionThe turbulent diffusion of suspended matter in an atmosphere is not only a topic of considerable intrinsic interest to the mathematical physicist and meteorologist, but also a problem of great practical interest. Release of particulate matter into the atmosphere at large has created o ne of the acute problems of the present day. Pollution of environment by industrial and domestic smoke, fumes and grit is widespread and has necessitated extensive studies in order to determine the concentration and distribution of pollutants in various areas. Pollutants discharge from stacks, whether chemical or radioactive, give rise to similar, but more localized, problems. The laws which govern turbulent diffusion in the atmosphere are also applicable to the study of the diffusion of toxic gases and the deposition of radioactive dust from nuclear explosion.The dispersion of diesel contaminants into the mine atmosphere is but a variant of a general class of diffusion-dilution problems relevant to underground mining practice. Most of the mine air pollutants, such as respirable dust, methane, diesel exhaust, and blasting fumes are produced in the face areas and haulage ways. Understanding of their dispersion in the mine airways is important to calculate their concentrations. In this paper, the development and use of mathematical models of mine production system, the engine exhaust air quality and engine exhaust transport are discussed. The over-all objective of this research effort is to evaluate the impacts of dieselization on production and ventilation systems and to aid in mine planning and design, as shown in the flow model in Figure I."

Jan 1, 1983

By Eric D. Jamieson

"How well is the Canadian coal industry able to expand in the tough competition with other fuels in Canada and with other suppliers in the international, metallurgical and thermal coal trade? Coal production as a whole decreased between 1950and 1960 and, although there has been a tripling of production since then, underground production continued to decrease until 1975. This trend has been reversed to a certain extent as a result of the modernization of mines in Cape Breton, but in 1978 over 85% of coal production came from surface mining.Against this background, the paper reviews current Canadian mining operations as described in papers presented at the 1979 CIM Annual General Meeting. Conclusions are then drawn regarding some of the longer-term mining applications in relation to the latest coal demand forecast, which indicates a potential Canadian production requirement of 160 million tonnes per year by 2000. IntroductionThe Canadian 'coal industry is experiencing a period of expansion and a new record for production is set with each passing year. This growth pattern over the last IS years has been based on two main markets-the generation of electricity in Canada and the export of coking coal to Japan. Supply to those markets has entailed either the development of mining, coal preparation and transportation systems for the delivery of large volumes of products with predetermined specifications or the establishment of minesite plants designed specifically to suit the characteristics of the coal in the adjacent deposits (Fig. I).Coal is a low-value commodity in relation to its bulk, and the economics of coal use become progressively less attractive with increasing distance from the producing mine. The transportation component in the export trade and in the movement of western coal to Ontario is a major cost factor. In the latter case, it approaches the cost of coal produced at the mine. In addition, the .international competition among coking coal producers chasing diminishing markets in a worldwide steel recession as well as the competition from U.S. coals and other fuel s for Canadian thermal coal have introduced a tight set of parameters to govern mining practices in all parts of the country. Some appreciation of the required changes in mining techniques brought about by declining traditional markets and the rigorous demands of the new bulk markets can be gained by comparing production from surface and underground mines over the past 25 years (Fig . 2)."

Jan 1, 1980

By M. Phylli Bray

"Concurrent with the continuing demise of many Canadian mining towns is the rise of a new method of providing remote mine sites with a workforce. This is the Long Distance Commute (LDC) which uses commuter labour and requires no permanent settlements to support the mine operation. It provides a flexible and cost effective method of operation to the industry and relieves both governments and industry of the expense of building and maintaining mining towns. However, little attention has been paid to the effect on workers or their families of the LDC work schedule whereby workers spend a fixed number of days at the site followed by a fixed number of days at home. Off-shore oil rig experience would indicate that negative social impacts may be expected. Research leading to an understanding of the problems involved seems to be indicated. One innovative suggestion has been to use already established but dying mining towns as workforce pick-up points for new LDC operations further north.BackgroundUntil recently, mine towns were considered as a necessary component of mine development. This was a natural symbiosis resulting from the need to provide workforce accommodation close to isolated mine sites. The early mine communities in Canada were often just a huddle of shacks around a head frame. Gradually mining companies began to provide housing which varied from basic duplexes and quads in grid pattern layout to professionally planned and designed towns, either model company towns or the more recent suburbs-in-the-bush, the so-called ""instant towns"" of the postWorld War II era of resource development. The improvement in accommodation reflected the need to attract a stable workforce as mine operations became more sophisticated. City amenities were expected and offered in these mine towns as a way of encouraging a permanent community of mining families. Indeed in towns like Manitouwdage, Schefferville, and others, it was not unusual to find a significant percentage of two- and three-generation families apparently providing the permanent mining communities so desired by mine operators."

Jan 1, 1991

By Navid Bahrani

Overview ? Case history of footwall slab failure ? Procedure used to build a finite element model ?? Pre- and post- mining topography ?? Slab geometry ?? Excavation stages ?? Input parameters ? Finite element modelling results ?? Unloading-induced displacements (magnitudes & directions) ?? Calibration of overall model using measured prism displacements ?? Shear stresses and displacements along the base of slab ?? Factors of safety at different stages ?? Effectiveness of rock bolts ?? Staged or unstaged model? ? Conclusion

May 1, 2008

By Nitin Bhavsar, Kaushik Vakil, Lakshmikanth Reddy, Sanjay Sarkar, Tathavadkar. Vilas, Bhavin Desai, Raghavendra Adiga

Gold and platinum group metals (PGM) do not dissolve in sulfate electrolyte from anode during electro-refining of primary copper. The PGM form solid ‘slimes’ which accumulates at bottom of the electrolytic cell. Typically, 8 to 10 ppm silver is present in copper cathodes, which is equivalent to almost 2% of silver loss during electro-refining. The silver can be cemented with cathode copper as soon as it is dissolved into the electrolyte from anode or during entrapment of slime particles in cathode. Over a period of time, the concentrates grade has deteriorated and change in type & amount of impurities in concentrate has resulted in higher silver loss during refining process. Therefore, an in-depth investigation was carried out in both fire- and electro-refining processes to understand the root causes of higher silver loss in copper cathodes. The detailed characterization and the plant data analysis were carried out. The results of study revealed that higher silver loss in 3rd crop cathodes as compared to 1st and 2nd crop cathodes from same anode. In anode silver was present in two forms, dissolved in copper (solid solution) and in slime phases such as Cu2-xAgxSeTe. SEM-EDX study of anode cross section confirmed higher silver and oxygen content in central region (core) of anode as compared that in both air and mold sides. This is due to non-uniform cooling of anode which was confirmed by the solidification modeling. Higher concentration of oxygen & silver at core of anode rised Ag+ concentration in electrolyte and slime particles during 3rd crop. The results of study were used to optimize the anode cooling process and also electrolyte chemistry to reduce the silver loss. The details of study carried out are discussed in this paper using the results of modeling, characterization and experimental studies. INTRODUCTION In the electrolytic refining of copper, fire refined copper anodes are used as raw material. Anodes contains copper of the range 99.5 to 99.6%, rest being the impurities. Hence, the purpose of the refining is (1) to remove the impurities so that final cathode conforms to the LME specifications and also (2) to recover the precious metal from the anode copper. When anode is dissolved, most of the impurities reports to the anode slime settled at the bottom of the cell, and rest dissolves in the electrolyte. Dissolved impurities remains in electrolyte and are removed during electrolyte recycling. However, sometime dissolved impurities and slime particles get entrapped in cathode due to disturbances in operational conditions. Metals dissolving in the electrolyte are the elements such as Ni, Co, Fe, Zn. The electrode potential of As, Sb and Bi being close to that of copper, these elements partly dissolve in the electrolyte. Noble metals like Ag, Au, Pt and Pd are generally insoluble and are thus expected to report to the anode slime. A small amount of the sliver content from the anode is dissolved in the electrolyte. Because the dissolved silver electroplates on the cathode at a smaller applied potential than copper, the cathode typically contains up to 8 ppm of silver. This is referred to as ‘silver loss’ in cathode (Cooper, 1987). Fortunately, silver is a rather benign impurity in copper due to its electrical conductivity being higher than copper. However, higher silver loss in cathode is loss of revenue for Copper smelter due to significant difference in their LME price.

Jan 1, 2019

By Adrian Dance

The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copper-zinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products. Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance. Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of the ROM and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling. One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost and reagent consumption. Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ?equivalent?) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ?ore? becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance ? and thereby profitability ? is a powerful tool. In an operation such as Antamina, where managing ore sources, campaigns and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency.

May 1, 2003

By E. M. De Souza, R. Penner

"Water is encountered at the majority of underground mines, both over their lifetime and during each stage of development and production. The dewatering system is one of the most important and costly components of an underground mining operation and it is often not well designed and analyzed. An effective design of a mine dewatering system will greatly reduce its energy cost as well as improve working conditions and reduce production costs. A computer-based system, called Qpump, has been developed to assist the underground operator to effectively design and/or assess over-all and local mine dewatering systems. The design features and principles used in the development of Qpump are introduced and an example which illustrates typical applications is presented.IntroductionTraditionally, dewatering operations have been given lower priority than many other operations in underground mining. Invariably water will be encountered during the sinking of the mine shaft, during development and subsequent production. The dewatering system thus becomes a very important component of an underground mine operation and, in fact, any mine manager will attest to the importance and necessity of an efficient mine dewatering system.The water problem is of varying importance at different mines. There are several factors that contribute to the water encountered. It is a function of the mining method and techniques utilized (backfill system, drilling and raising technology, dust control sprays, shaft water rings, etc.) and of prevailing conditions (ground water, rock structure and permeability). In some cases a mine may be so dry that little pumping is required while in others, the weight of water pumped may exceed by many times that of ore mined.The successful design and application of a mine dewatering system is dependent upon the operating conditions of each specific operation. There are no standard procedures and systems which can be used for all mining situations. However, an effective water system will greatly reduce the energy and production costs of a mine, improve working conditions and eliminate headaches because of flooded working places."

Jan 1, 1993

Bahuerachi Project Characteristics Why it?s nicer at Bahuerachi Mexico is a mining country Low political, regulatory and trade risk Low social/permitting risk Proximity to infrastructure Road Power grid (8 km) Rail line (25 km) High grade zones (skarns), CRD and near surface oxide component are sweet spots to the overall system. Size of low grade system points to potential long mine life?and numerous new targets developing. Timelines-2006? 90 to 100 combined RC and core holes to go! MAIN ZONE Drilling ? Goat ?Finish Mid April ? Main Zone, going North, depth of testing dependent, estimated for May ? North Lobe-May ? Commission independent resource estimate by May 06 for results of first pass drilling to date ?tonnesand grades ?Main Zone Milestone. ? Continue infill or expanded drilling to July (minimum) ? 1stpass RC scheduled until September OTHER Targets ? Begin drill testing North Skarn target Mid-April, minimum 5 drill holes, 1,000 meters. Ongoing expansion of target with surface work (mapping) ? Road to Colome(Skarnin north of Main Zone) as part of porphyry program ? Tule(southern) porphyry and skarn system-soils and mapping OUTSTANDING events Metallurgical report on floating and leaching tests (Sulphide/oxides).

May 1, 2006