Search Documents

By Parfitt RL

A quarter of the North Island, New Zealand is covered by weathered volcanic tephras of mainly andesitic and rhyolitic compositions. Rapid weathering of basic volcanic glass and slower weathering of acidic glass have produced short-range order alumino-silicate clays such as allophane. Although amorphous to x-rays they have a high degree of local structure. Allophane comprises hollo spheres of approximately 40 diameter and 7 X wall thickness. This small particle size and morphology gives a very high surface area (up to 800 m2/g). Ferrihydrite is another short-range order clay of similar small size and high surface area; it has ò formed from the rapid oxidation of water containing ferrous iron derived from volcanic rocks. The quantity of allophane present in tephra depends upon the climate, the nature of the volcanic glass and the time it has weathered. In New Zealand highest amounts (-50%) occur in beds of andesitic ash deposited on old ignimbrite surfaces with mean annual rainfalls >1600 mm. Both allophane and ferrihydrite will react with oxyanions, such as phosphate, arsenate or borate, and remove them from solution. Other anions such as fluoride also react with aluminium sites on the mineral surface. At NZ Soil Bureau, Department of Scientific and Industrial Research (DSIR), New Zealand, techniques have been developed for granulating allophane to enable it to be used to remove pollutants from solution without dispersion into the liquid phase. This granulated allophane can be used to remove phosphate from sewage effluent or fluoride from tap water without having a sedimentation stage to remove the clay.

Jan 1, 1987

By Porter I

Rock mass classification systems have emerged as a powerful tool which can be used for assessing ground conditions and determining support requirements in underground mines. They should not be used as a substitute for complete engineering design, but rather as a supplement to observational methods and analytical study. In general, the use of rock mass classification is attractive, but each classification system has various deficiencies. Use of any particular system should be made only with knowledge of that systems limitations. It is desirable to employ a number of systems and design methods which will allow for comparison and lead to a better understanding of the rock mass condition.The Rock Mass Quality system (Q-System), developed by the Norwegian Geotechnical Institute, and the Rock Mass Rating (RMR) System, Bieniawski, were designed primarily for civil engineering structures. Laubscher et al (1978) further developed the RMR-system specifically for rock mechanics engineering in the mining industry. A method of stope design, which introduces a stability factor for the rock mass and compares this with hydraulic radius, was developed by Mathews et al (1981). This paper reviews the above systems by applying them to stability assessment of crown pillars in two Australian metal mines and provides a critical analysis of the various approaches. In particular each system will be analysed to determine its suitability for use in crown pillar design. The most suitable system(s) will form the basis for future development in crown pillar stability analysis.

Jan 1, 1994

By Iley J. D

The production of zinc from low grade concentrates, particularly those high in iron, has a poor economic return due to a combination of higher concentrate transport costs, increased processing costs and an increased cost for disposal of iron residues. The production of iron-bearing residues from the electrolytic zinc process is also seen as undesirable for both cost and environmental reasons. This paper details the pilot plant testwork conducted at the Pasminco Research Centre in conjunction with Minproc for the production of zinc oxide fume from a high-iron zinc sulphide concentrate from Colquiri in Bolivia. The concentrate is derived from a tailings retreatment operation and has a high iron content (40 - 45 per cent Zn, 14 - 17 per cent Fe) due to the presence of marmatite. Pilot plant trials were conducted using the slag bath reactor at Pasminco Research Centre at rates up to 500 kg/h of pelletised zinc concentrate, using a natural gas/oxygen-enriched air lance. The fume produced averaged 76 per cent Zn at recoveries up to 96 per cent and was recovered in a baghouse after gas cooling. The iron was oxidised into a fayalitic slag that passed the TCLP test (toxicity characteristic leaching procedure) and the sulphur was oxidised to produce a high SO2 gas which would be suitable for sulphuric acid production. The process produces a zinc oxide fume that can replace calcine as a feed for electrolytic zinc plants. The iron reports to a stable slag for disposal, thus eliminating the need for its disposal as jarosite from the leach plant. Only a simple leaching operation on the fume is required as there is no zinc ferrite present.

Jan 1, 1993

By S Paciornik, G Schinazi, M H. de Pinho Maur-cio, M B. Vieira, O da Fonseca Martins Gomes, D T. Wagner

Vale (previously CVRD û Companhia Vale do Rio Doce) evaluates the microstructure of sinters in order to understand their characteristics and behaviour in the agglomeration process, and the correlation with conventional quality parameters. Efforts on image analysis development are in progress between Vale and PUC-Rio in order to improve both the qualitative and quantitative evaluation of a representative portion of material. In the present work, digital microscopy techniques were developed allowing this kind of assessment. Employing a motorised and computer controlled optical microscope, low magnification mosaic images covering complete sinter samples were automatically obtained. The mosaics provide a powerful qualitative overview of the whole sample while allowing low resolution quantitative evaluation of the major phases. In addition, quantitative results for phase fractions were compared for the same sample regions at three magnifications (5x, 10x and 20x objective lenses). A single field (1 x 1) at the lowest magnification corresponds to mosaics of 2 x 2 and 4 x 4 images at the higher magnifications. The automated system allows perfect registration between the mosaics and the single image. Changes in phase discrimination were evaluated as a function of optical resolution, and phase fractions obtained by interactive segmentation of the image histograms were compared. While finer dark phases, eg silicates, were only visible with the best optical resolution, coarser phases such as haematite and pores were measured at all resolutions. For haematite, magnetite, ferrite and pores, the largest relative error in area fraction, between the images obtained with the 5x and 20x lenses, was 12 per cent. The results for silicate were less accurate with a relative error of 44 per cent. The results indicate that digital microscopy provides a flexible method for qualitative and quantitative evaluation of these materials.

Jan 1, 2008

By Getliffe RK

It is becoming more and more difficult to operate mineral and metal processes profitably, as operating costs rise, quality demands in-crease, international competition becomes more fierce and Government charges remain at their current levels. Profitability today depends upon efficient operations, which can only be achieved through precise and dependable con-trol of each process unit comprising thetotal plant.Modern process control systems utilise distributed architecture with microprocessor-based controllers, data acquisition devices and VDU operator stations. Honeywell intro-duced this control technology in 1975 with the "Total Distributed Control" System. Now, building on the proven performance and re-liability inherent in TDC hiway modules, Honeywell has extended the TDC system to inte-grate both management information and control by providing distributed processing modules on the new TDC 3000 Local Control Network (LCN).

Jan 1, 1985

By Nixon J

Open pit mining began in 1978 at the Woodlawn base metals deposit. For its ten years as an open pit the mine was financially unsuccessful as a combined result of difficult metallurgy and industrial unrest. In 1985 CRA bought out two American joint venturers with a view to going underground and a prerequisite to expending capital on developing an underground operation was to improve the industrial climate, work practices and mining methods.Following feasibility work, continuous production from the underground mine began in 1986 using mechanised cut and fill methods and a workforce trained under a multiskilling program. Men with no previous underground experience were trained by supervisors with backgrounds as miners to undertake all the work that is required with increases in skill levels being rewarded with increases in pay.

Jan 1, 1992

By OÆBrien D, Priddle D

In order to avoid costly moisture penalties on coal shipments and to minimise rail freight costs, screen bowl centrifuges were selected and installed in the Mount Thorley Coal Preparation Plant for dewatering fine coal product. The Mount Thorley fine coal circuit consists of desliming the -0.5 mm (ww) fine coal in two stages of classifying cyclones prior to recovery by froth flotation. Provision has been made to bypass the flotation circuit with the classified flotation feed reporting directly to product and the centrifuge dewatering circuit has been designed to handle either flotation feed or flotation product. Major mechanical failures of the gearboxes and the ceramic tiling occurred early in the operation life of the machines which led to design changes being made to achieve satisfactory operation. This paper discusses the operating experience at Mount Thorley with respect to both mechanical and metallurgical performance of the screen bowl centrifuges since their installation in 1985.

Jan 1, 1989

By Gray J, Krouse HR, Changkakoti A, Kwak TAP

The Dachang tin field with more than one hundred million tonnes of ore at 1% tin and 3% Zn is one of the largest tin fields in the world. It comprises five carbonate replacement tin deposits, of which the Changpo deposit containing about 80 million tonnes of ore at about 1% tin is the largest deposit. The deposit, hosted by middle Devonian limestone, argillaceous limestone and black shale, is genetically related to the Longxianggei granite.The oxygen, hydrogen and carbon isotope data of minerals, rocks and fluids suggest a magmatic fluid which evolved during the crystallization of the Longxianggei granite. Mass balance calculations show that the depletions observed in 180 and 13C values of calcites from the ore bodies to the country rocks were due to continous isotopic exchange reactions between the magmatic fluid and the marine limestones at different W/R ratios and between 300 and 600¦C.

Jan 1, 1990

By D Johansson, C Yi, U Nyberg

Emulsion explosives are a common industrial explosive and have a non-ideal detonation behaviour. The detonation performance for a given product changes with the charge diameter, ground conditions, con?nement and density. The burning process of an emulsion explosive has been modelled with an ignition and growth model in the LS-DYNA code. The parameters in the burning rate function are calibrated by the detonation velocities and the detonation front curvature radii from emulsion explosive tests. A Perl program was developed for an efficient estimation of the parameters, and the results show that the calibrated parameters can predict both detonation velocities and the detonation front curvatures.CITATION:Yi, C, Nyberg, U and Johansson, D, 2015. Parameter determination of an ignition and growth model from emulsion explosive tests, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 585–590 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Ohga K, Isobe T

Basing upon many and long practical experiences of gas drainage from coal seam and results investigations on the gas flow through in si-tu coal seam using tracer gases,it became clear that solid coal itself is hardly gas permeable or has extremely low gas permeability. Almost all of gas flows from a coal seam into boreholes through fracture net- works intersecting with them.Primary and secondary fractures in coal seams differ in their size and continuity from place to place according to differences of the coal strength and the stress conditions. A lot of gas can be drained through boreholes which intersect with many and/or wide fractures. A mathematical model for gas flow from a coal seam to a borehole through a discoidal fracture is proposed. From the numerical analyses,the apparent radius of the discoidal fracture in this model is shown to be a good indication of the gas drainage ratio. In addition to this,an atempt to make fractures around a borehole using high velocity water jet(ca.lmm dia.,300-700atm., 100-200 1/min.) is introduced.

Jan 1, 1982

Agglomeration pre-treatment is a new process now being used here and overseas whereby problems arising with the heap leaching of gold and silver from materials containing critical amounts of fines or clay can be simply and cheaply overcome. The technique involves mixing the material with a suitable binder, commonly Portland Cement, and tumbling the moistened material to agglomerate the fines. These agglomerates are placed on the leach pad and cured prior to leaching. Test results, plant and operating cost data are presented. INTRODUCTION Heap leaching is a low capital and operating cost alternative to conven tional processing techniques for gold and silver extraction. A number of commercial-scale operations have recently started in the United States and the method is being considered for further deposits there and elsewhere.

Jan 1, 1982

Many stress measuring instruments use overcoring stress-relief principles but adopt different sensing techniques. Every technique is subject to certain limitations of rock types and conditions. To investigate the performance and reliability of the instruments in field measurement, a simple and practical approach has been developed to allow comparable laboratory results to be obtained which simulate in-situ rock and stress conditions. Four commonly used devices, the USBM deformation gauge, the CSIRO HI cell,the CSIR triaxial cell and the UNSW SI cell were thoroughly tested in the laboratory. Some conclusions have been drawn as to their suitability and reliability in different field conditions. Recommendations are provided for the choice of an appropriate technique for a given rock type and condition. A new thin-wall cell that overcomes the disadvantages of earlier devices has been developed and tested. Its laboratory performance shows that it has good prospects.

Jan 1, 1990

By Olofsson O, Durance M-V, Villeneuve J

Modelling of the Sala Agitated Mill (SAM) using a simplified solution to the population balance approach has been carried out. The rate of breakage is modified by the mill power, providing predictions of the resulting product size distribution for different grinding conditions and mill sizes. The power of the mill is estimated by a physically derived function, using an assumption that the mill power consumption mainly arises from the ball to ball friction within the mill. The grinding efficiency, depending on the media ball size and pulp density is approximated in the model. Experimental work on grinding a complex sulphide ore using a pilot scale SAM 7.5 has been carried out. Good agreement has been found between the data from the test campaign and the simulated values. The model has also been validated with experimental data from a pilot grinding of calcium carbonate and from an industrial mill. The model is included in the USIM PAC simulation software.

Jan 1, 1995

The Porphyry Gold Mine (150km NE of Kalgoorlie) was reopened in November 1983 with production commencing in April 1984. Original reserves quoted for the open pit were 822000 tonnes at 5.2 g/t Au based on wide spaced diamond drill holes. Close spaced grade control drilling has revealed some loss of tonnage and a significantly lower grade. In the area of the pit mined to 30 June 1985 this grade control reserve estimate contained 67% of the gold in the original ore reserve with the grade being 19% lower. It is anticipated that the final grade control reserve estimate will contain around 80-85% of the gold contained in the original reserve. There has been close agreement between the Mill Head grade (4.19 g/t Au) and the grade control predicted grade (4.2 g/t Au) confirming that dilution is not a major problem. After initial poor agreement (attributed to "lock-up" in the circuit) the bullion calculated head grade steadied out at 93% of the grade control prediction. This difference is considered to represent the geostatistical bias in the drill hole/crushed rock sampling. Gold recovery has been in the range 93-95% (compared with bullion calculated grade). The net result is that the recovered grade of ore mined to 30 June 1985 is 70% of the original ore reserve grade.

Jan 1, 1986

The first stage in process design for coal preparation is a study of the coal seam and its associated features followed by an examination of the mining method to.be employed and the coal market requirements. Normally benefication is based upon the differences in relative densities of the coal constituents and asso- ciated ash forming components. Since initial liberation is obtained at a relatively large particle size, the size to which coal is crushed is more subject to the market requirements than to liberation studies. It is possible to estimate energy requirements for comminution and recoveries and product grades can be cal- culated following the interpretation of standard laboratory tests. Numerous units are available for the separation and concentration of the components of run of mine coal in- cluding jigging, dense media separators, and for the finer particle size fractions, flowing film separators, dense media cyclones and froth flotation.

Jan 1, 1975

By S Fidler

Underground coal gasification (UCG) is a process by which coal is converted in situ to a combustible gas that can be used as a fuel or chemical feedstock. The process has been used in commercial-size projects in the former Soviet Union for more than 40 years, while significant national research programs have been undertaken in the United States and Western Europe. The Chinchilla UCG project is located at a site southeast of Chinchilla in Queensland. The UCG operation commenced in December 1999. A controlled shutdown of the process was initiated in January 2002 and successfully completed in April 2003. The process is currently under conservation and ready for restoration of gas production for commercial use in the near future. Groundwater plays an important role in the gas formation process during UCG. Most of the process water required for chemical reactions is usually derived from the coal seam itself and from surrounding aquifers. If insufficient water is available for chemical reactions the UCG gas will contain reduced concentrations of combustible components, and conversely, excessive water influx into the process area would cool down the reactor and thus limit the energy available for gas production reactions. Because of the importance of groundwater in the gasification reactions, and the potential to contaminate groundwater if the process is not correctly controlled, it is essential to predict and to control the groundwater influx into underground gasifiers during and after underground gasification. Control of groundwater requires a thorough understanding of hydrogeological conditions in the vicinity of the gasifier in order to be able to predict inflow rates, and constant monitoring throughout the process of water production rates and groundwater pressure in the coal seam and adjacent aquifers. Hydrogeological testing and groundwater monitoring in the vicinity of the UCG operation commenced six months in advance of its initiation. Monitoring of groundwater pressures in the vicinity of the gasifier have also been undertaken using vibrating wire piezometers installed in the coal seam at varying distances from the gasifier. This paper presents the results of the hydrogeological testing and groundwater quality monitoring carried out at the site, which show that it is possible to operate a UCG process without uncontrolled impacts on groundwater.

Jan 1, 2003

By Dmitrievskaya TY, Cheremnykh PA, Kuftinova IV, Yaremenko VN

The comprehensive processing of raw materials and the tendency to waste-free production require the combination of various methods of concentrating mineral resources. Magnetic separation, an ecologically clean method of concentration, is one step in the technological cycle of ore processing, and cleaning and classifying of raw materials. Separators with superconducting magnetic systems cooled by liquid helium are the novel equipment for practical concentration. Recently, high-gradient (HGMS) and open-gradient (OGMS) magnetic separators using the effect of superconductivity have appeared. The separators of the first type are expedient in the head-end of the technological cycle, as they are most efficient for processing of particles 100 ¦m and greater in size. In this case the main task is to obtain pure tailings with a minimum amount of the useful component. This method allows the essential reduction in the cost of the subsequent crushing and grinding, because only the magnetic concentrate is directed to further processing. The separators of the VGMS type are used more efficiently in the final stages of the concentration cycle to condition the end product. The present work is devoted to the theoretical and experimental investigation of the motion of weakly magnetic particles in the working chamber of superconducting separators of the open-gradient magnetic separator (OGMS) and HGMS types. The flat OGMS is equipped by a magnetic system with NbTi racetracks cooled by liquid helium. The chamber is divided into zones by partitions parallel to the plane of the magnetic system. It is shown how, depending on the number of the zones and their depths, the extraction function of the OGMS varies and the transition from the OGMS to the HGMS occurs. The particles 2 mm and less in size are considered. The extraction parameter distribution of the particles was measured for a multicomponent weakly magnetic ore. It was experimentally shown that xD2 is the extraction parameter for the particles in the OGMS on condition that (p-po)D /l8/tl/g

Jan 1, 1993

By Bigdy D. N

The paper describes a system for providing mine management with a continuous indication of the effectivness of longwall coalface powered supports in controlling roof-to-floor convergence. The system comprises on-face instrumentation monitoring convergence and support leg circuit pressures, a means of transmitting the output of that instrumentation to the surface for collection, and software which presents both a condensed analysis for rapid review of the current state, and extended analyses from which remedial action can be recommended if a problem is identified. The results of a field trial are presented showing that meaningful results can be obtained.

Jan 1, 1988

By R O. Laidlaw, J L. Mauk

The Coeur d'Alene mining district in northern Idaho, USA is the second largest producer of silver in the world. Mesothermal silver-lead-zinc veins occur in the metasedimentary rocks of the Belt Supergroup with five main types of associated hydrothermal alteration: 1) feldspar destruction, 2) hydrothermal bleaching, 3) carbonatisation, 4) sulfidation, and 5) silicification. Hydrothermal bleaching is characterised by hematite destruction with associated siderite and quartz veins and veinlets, coarse euhedral pyrite and magnetite. Bleached zones envelop both mineralised and barren veins and extend for metres to tens of metres into the wall rocks. Carbonatisation consists of addition of siderite, which occurs as veins, veinlets, stockwork, irregular blebs or spots, and coarsely disseminated grains, depending on the relative distance from the main vein structure. Siderite envelops nearly all mineralised veins, relates to all other alteration types and extends from several metres to tens of metres into the wall rocks. Pyrite and galena alteration dominate sulfidation and are associated with some mineralised veins. Pyrite alteration strongly correlates with siderite alteration and exists in three main forms: a) very fine-grained pyrite flooding, which can extend for metres to tens of metres into wall rocks; b) coarse-grained, euhedral pyrite, which is sporadic and associated with the redox boundary in hydrothermally bleached zones; and c) small isolated zones (6 - 15 cm) of medium-grained, subhedral to euhedral pyrite associated with pervasive siderite alteration. Where present, disseminated galena extends for metres to tens of metres into the wall rocks. Silicification is characterised by veins, veinlets, stringers, irregular patches and variable hardness in siltites and commonly appears in association with hydrothermal bleaching and siderite alteration. Although related to mineralisation, silicification is sporadic and in most places a clear envelope around mineralised veins cannot be identified.

Jan 1, 2001

This paper gives the background to the development of solvent extraction processes for the recovery of metals from aqueous solutions. Its growing importance in Australia for the recovery of both uranium and copper is dis- cussed, as well as the developments in mixer-settler design as applied to recent plants. The economic significance of solvent extraction as an alterna- tive to cementation is discussed and important features of each process are highlighted by comparison of costs for each process in a hypothetical situa- Tion.

Jan 1, 1971