Search Documents

By C Zschiesche, alam, A Abadias Llamas, A K

An integrated experimental and thermodynamic modelling study of the phase equilibria in the FeOFeO1.5- SbO1.5-SiO2 system in equilibrium with liquid Sb and Sb-Ag metal has been undertaken to develop thermodynamic model of the Na-Si-Fe-O slag system with S-Sn-Sb-Pb-As minor elements based on the experimental investigation of the selected sub-systems. New experimental phase equilibria data at 575–1600°C were obtained for this system using high-temperature equilibration of synthetic mixtures with predetermined compositions in sealed silica ampoules, Fe3O4 basket in sealed silica ampoule, or Re foils, a rapid quenching technique, and electron probe X-ray microanalysis of the equilibrated phase compositions. Experimental results on phase equilibria in the Fe-Sb-Si-O+Sb metal system obtained helped to produce initial set of model parameters in the slag. The primary phase fields of quartz/tridymite/cristobalite (SiO2), 2 high-SiO2 immiscible liquids, olivine (Fe2SiO4), wustite (FeO1+x), spinel (Fe3O4), schafarzikite (FeSb2O4) and valentinite/ senarmontite (Sb2O3) were identified in the binary Sb2O3-FeO, Sb2O3-SiO2 and ternary FeO-Sb2O3- SiO2 systems. Further refinement, particularly the distribution of excess Gibbs energy among the ‘FeO’-Sb2O3-SiO2 and ‘FeO1.5’-Sb2O3-SiO2 interactions, required the study at more oxidising conditions. Oxygen potential was increased using an inert metal (Ag) rather than using the gas flow due to the high volatility of Sb-containing gaseous species. Liquid Ag-Sb alloys with low concentrations of Sb of a few percent were used. At these conditions, the concentration of AgO0.5 in slag was below 1 mol per cent, which had a small effect on observed phase equilibria in the system. In addition, important information on the solubility of silver in slags is produced, which can be valuable when treating electronic recycling materials or primary silver-containing ores through the Pb process. Two main areas were addressed: the spinel-tridymite boundary (40–70 per cent SiO2 in slag) and spinel liquidus near 15 per cent SiO2 in slag. This allowed to deconvolute the separate contributions of the FeO-Sb2O3(-SiO2) and Fe2O3-Sb2O3(-SiO2) systems.

Jun 17, 2024

By C Jacobsen, N Harries

Assessing and managing instability hazards is an essential activity when working with unstable natural slopes and excavated open pit mining slopes. Slope monitoring has become the standard technique for the management of geotechnical risks associated with mine slope instability hazards. In recent decades, a proliferation of new monitoring techniques such as terrestrial radar, satellite InSAR and LIDAR have become standard operational tools, complementing conventional survey-based monitoring solutions. A reliable monitoring system should identify and record incipient anomalous slope movement. Although the most obvious purpose of a monitoring system is safety related, slope deformation and performance monitoring also enhance the understanding of slope behaviour and assists in improving system design and implementation. For a monitoring system to be considered an effective early warning tool, it needs to operate in real-time and should be linked to the mine’s emergency communication systems. Terrestrial radar systems have been developed that can provide near real-time measurements, at a high level of precision and covering broad areas in all weather conditions. This has had a positive impact on the management of geotechnical risks in operational conditions. The technology adoption of RADAR in mine monitoring has significantly progressed in the last 20 years from technology enthusiasts, to visionaries, to pragmatists to conservative users. However, the increasing adoption of RADAR cannot reduce or remove other monitoring techniques that often have important benefits; even if these technologies cannot be used as a real-time operational tool. An increasing awareness on the importance of combining data from different monitoring techniques to develop a holistic picture of all possible geotechnical hazards is a current industry trend. This is proving to be an excellent foundation for managing hazards associated with slope instability in open pit mines, and is only expected to improve with time with the adoption of new technologies based on big data and Artificial Intelligence (AI).

Nov 29, 2022

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By B Murphy

Safescape Laddertube provides an improved system for emergency egress in ventilation shafts. The addition of Laddertube in a rise has very little impact on ventilation flow, studies have indicated that the difference in flow velocities are difficult to measure due to the minimal impact. Due to the size and open-ended nature of Laddertube, the air velocity inside and out of the Laddertube is mostly linear. Laddertube can be used either permanently or during an emergency as a secondary ventilation duct. One project involved a 385 m ladder installed in a surface return air raise that could be made to bypass the primary circuit and supply fresh air to a sea container fresh air base at the bottom of the raise. Laddertube has been designed to be installed to any feasible length and can be fitted with a climb assist system ensuring enhanced speed and reduced fatigue during ascent. The climb assist used in association with Laddertube is a Tractelift system which applies a weight relief of up to 36 kg off the climber’s body weight when using the ladder. This system has successfully been tested for ladders up to 600 m in length and is currently in use for a ladder of 185 m length. The use of refuge chambers in underground coalmines has long been a contentious issue due to the concern that while it may provide temporary shelter, the risk of being exposed to high heat or the inability for rescuers to access them due to fire or explosive atmosphere means that they may be effectively trapped. The additional application for coal environments includes Laddertube installed alongside a refuge chamber concealed behind a blast proof door ensuring a secondary means of emergency egress. In certain operations designs may allow for this chamber to be provided withpositive pressure fresh air.

Oct 12, 2022

By Andrews B. S

The sinter plant at the Sulphide Corporation's Cockle Creek works produces a feed for the company's Imperial Smelting Furnace. The feed contains lead and zinc oxides and all the fluxes necessary for furnace operation. The quality of this feed is a major factor in furnace performance and the considerable flexibility of operation possible at the sinter plant has been used in efforts to achieve optimum operating conditions.Operating data is processed daily and information gathered from this source has led to three of the four improvements described.These improvements have resulted from elimination of gas recirculation, reduction of sinter returns sizing and alteration of ignition conditions and main layer fuel loading.

Jan 1, 1964

By D Finn, D Kentwell

Experience has shown that the E-Type multiple indicator kriging (MIK) estimation technique often works well for resource estimation in stockwork mineralisation that contains a mixture of high and low-grade mineralisation types that are difficult or impossible to separate spatially. E-Type MIK, like ordinary kriging (OK) is a smoothing estimator and where data is sparse can result in estimates of grade tonnage curves that do not reflect the true block variability at selective mining unit (SMU) scale. The rank and replace (RR) estimation methodology is designed to reproduce both local block accuracy and true block variability at SMU scale and has shown good results when used with highly skewed unimodal diffusive style mineralisation. This paper examines the use of RR with mosaic style mineralisation typically found in stockworks via a case study using real data from Newcrest’s Telfer West Dome deposit. Resource level estimation results for ordinary kriging (OK), E-Type MIK and RR are compared to close spaced grade control models as the reference reality.Results show that stationarity requirements and declustering can severely impact on the usefulness of the rank and replace technique and that it should only be used where trends are not too strong and data are relatively uniformly spaced. This does not rule out its application to stockwork or mosaic style deposits. However, in this case, the presence of trends and different data densities requires the non-stationary domain to be further broken down into sub domains for the RR technique to be effective.CITATION:Kentwell, D and Finn, D, 2017. Testing new estimation techniques – rank and replace: a stockwork case study, in Proceedings Tenth International Mining Geology Conference 2017, pp 365–374 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By P C. J Blackney, I M. Glacken

Spotted Quoll is a massive sulfide nickel deposit located in the Forrestania greenstone belt in the Archaean Yilgarn block in Western Australia. Discovered in October 2007, mining has progressed from open pit to underground and currently uses longhole open stoping with paste fill as the primary stoping method. Immediately prior to 2019, the Mineral Resource estimate (MRE) was defined by a single grade domain of nickel greater than or equal to 0.8 per cent, irrespective of the host lithology, a legacy of the original ore wireframe being built using explicit methods. While a number of obvious structural offsets were honoured in this nickel grade domain, only one modelled fault was used to undertake domaining of arsenic. From 2019 onwards, implicit modelling in Leapfrog Geo™ was used to construct a mine-scale geological model, which triggered the definition of a high-grade core of massive/matrix nickel sulfides surrounded by a low-grade halo of stringer/disseminated nickel sulfides in the surrounding rock. As part of the evolution of the geological model and with the aid of Seequent Central™ to allow collaboration between site-based mine geologists, Perth-based resource geologists and Melbourne-based consultants, a detailed review of the structural mapping was carried out as additional information from underground development became available. This allowed numerous faults and shears to be identified – particularly in the lower half of the mine. These were used to define further structural domains and to refine the understanding of the nickel and arsenic grade distributions in the mineralised envelope. The increased definition to the domains provided by the geological model resulted in a significant improvement in the accuracy of the Mineral Resource estimate, as measured by reconciliation using voids of the mined stopes determined from the cavity monitoring survey (CMS).

Mar 22, 2022

By R Ballantyne, M Adams

Time Usage Models, used as a basis for calculating performance indicators for mobile mining equipment, have developed from very simple to very sophisticated models. This development has paralleled the increased collection and analysis of production data that itself has been enabled by the evolution of underground voice and data communications along with the relevant information systems. A Time Usage Model divides the hours that equipment is (or is not) used into standard components, by a hierarchical breakdown, so that measures of productivity can be used to compare performance of both people and equipment. The calculation of equipment availability, and thus the underlying Time Usage Model, has always been an extremely emotive topic as different groups use time usage information for different purposes. The direct link between measuring performance Key Performance Indicators (KPI) calculated from these models and employee rewards impacts upon the workforce. This paper discusses the conflict in use by various stakeholders and proposes ways to address some of the more contentious issues each supported by case studies. The simple status code functionality used by early systems has proven inadequate, leading to the evolution of “work-arounds”. These workarounds have become the norm and unfortunately have become embedded in the next generation of models and the information systems that incorporate them. This paper contends that the industry should stop building Time Usage Models to accommodate shortcomings in proprietary systems, but rather collaborate with suppliers to develop innovative methods to deal with the fundamental requirements. There are many points of differentiation that are not clear-cut. Pitfalls are discussed as well as threats to success. A framework of rules is developed as guidelines for how a Time Usage Model should be developed and applied. This will hopefully stimulate the on-going discussion as to how Equipment Availability and other components of the model should be calculated.

Mar 15, 2021

By F Djukic, T Fisher, G Irving

Questionnaires were sent to 12 underground metalliferous mines in Queensland to enquire how these mines control diesel emissions from mobile diesel engines used underground. Where responses or controls were absent, discussion has been provided. A significant finding concerns secondary ventilation design rates. Some mines were designing ventilation rates to meet the superseded Mines Regulation Act of 1989 which required 0.04 m3/s/kW. The current Queensland Mining and Quarrying Safety and Health Regulation (2001) is risk based. In line with other jurisdictions, including New South Wales (NSW) and most Provinces in Canada, a minimum ventilation rate of 0.06 m3/s/kW is acceptable. However, this design ventilation rate will vary in practice depending on the diesel engines and controls. Dedicated ventilation engineers and technicians should be appointed to evaluate the effectiveness of the ventilation system. Personal exposure monitoring is required to confirm that exposure standards are not being exceeded. The primary control practice should be to reduce the emission at source. This can be ensured by purchasing low emission (Tier 2, Tier 3) equipment. In addition, the use of ultra low sulfur fuel (et al, 2002). Diesel fuel with a low aromatic content such as Eromanga diesel fuel will also mean employees are exposed to lower levels of poly-cyclic aromatic hydrocarbons. These controls should be carried out in parallel with good maintenance practices. Preventative maintenance should be programmed and emissions be routinely tested, including both gaseous and particulate pollutants and compared against defined criteria. According to McGinn, 2002, there are a number of fundamental tools necessary to carry out preventative maintenance. These are outlined in maintenance guidelines and best practices for diesel engines in underground mining produced for the Diesel Emissions Evaluation Program (DEEP). An effective diesel emission management system needs to be fully integrated within the Safety and Health Management System. These requirements are further discussed in this paper.

Jan 1, 2007

By J Carswell, K McTyer

The Pajingo gold operation in Queensland is approximately 50 kilometres south of Charters Towers and 134km south-west of Townsville. The resource was discovered in 1983 and first open pit gold production began in 1986. The mine traditionally employed a bottom-up sequence – a combination of modified and traditional Avoca methods with run-of-mine waste backfill. This practice caused many high-grade crown pillars to be left in place, yet accessible. In recent years, these crown pillars have been extracted by injection grouting of rockfill. This process facilitated blind up-hole open stoping. To date, thirteen separate injection campaigns have been completed, of which ten were deemed successful. In general, the two key technical difficulties in this mining technique are: maintaining a consistent high-quality ground consolidation of the rock fill material; and controlling the drill and blast practices during stoping. Here, effective drill-and-blast control was found to be essential to achieve the dual aims of 100% extraction, and maximum sill pillar stability to minimise dilution. During stoping, the technical performance of the consolidated rock-fill was recorded; both to verify the design, and to identify operational improvements. The results showed that Pajingo has realised both reduced production down-time through use of early strength gain grout, and more rapid and thorough grout consolidation through changes to the emplacement method. The optimisation of consolidated rock fill has led to several quantifiable benefits to the mine, including: profitable extraction of previously sterilised crown pillars resulting in both increased ore reserves and production profile; improvements to the stability of grouted stope crowns, thereby reducing safety and production related; risks associated with open up-hole stopes; reduction in cost and time constraints, with respect to the grouting of loose fill; and reduction in grout curing time – from 14 days to 8 days – thereby minimising production down-time. This paper is a case study of the evolution and optimisation of the up-hole open stoping mining method at Pajingo. The challenges and successes are discussed in terms of their key mining outcomes. CITATION:McTyer, K and Carswell, J, 2018. Evolution of rock fill consolidation at Pajingo Gold Mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 66–77 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By A F. Cropp, D J. Bradshaw, W R. Goodall

Mineralogy and critically the texture of both the ore and gangue phases are of paramount importance in the flotation recovery of copper from porphyry ores. Mineralogy and texture will define the theoretical grade recovery curve for a feed ore. Actual grade-recovery falling below this may be due to texture and gangue influences, whilst desired grade-recovery above this line will not be possible unless the characteristics of the feed are altered.This review discusses examples of porphyry copper deposits where process mineralogy has been used to characterise these textural and gangue influences on recovery by flotation. More specifically, the influence exerted by grain size, liberation, association and elemental distribution is explored. The implications of these on overall plant philosophy and operation are highlighted, along with the subsequent potential impact on recovery.CITATION:Cropp, A F, Goodall, W R and Bradshaw, D J, 2013. The influence of textural variation and gangue mineralogy on recovery of copper by flotation from porphyry ore - a review, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 279-292 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By A J. Daniels

Macraes Mine is a large-scale open-cut and underground gold mine located in Central Otago, on the South Island of New Zealand. This paper presents the role of geological mapping in the grade control process at Macraes Open Pit as a case study, and demonstrates how systematic geological mapping can add significant value to the mining cycle. Geological mapping has proved to be a valuable foundation for orebody interpretation and analysis.Practical applications and lessons learnt are summarised, including predictive control of the orebody, improvement of geotechnical modelling, and identification of further exploration targets.

Aug 22, 2011

By J A. Meadows, M G. Annandale, G Castelain

Bauxite mining on Cape York Peninsula (CYP) commenced in the early 1960s in the region surrounding the town of Weipa. Rio Tinto Alcan (RTA) operates its bauxite mines on the homelands of 11 Indigenous Traditional Owner groups. The mining activity currently operates under three Aboriginal Agreements including an Indigenous Land Use Agreement – the Western Cape Communities Coexistence Agreement (WCCCA) – which provides RTA with access to the land in return for a range of benefits to the Traditional Owners, including employment, training, royalty payments and future relinquishment of the land (Klimenko and Evans, 2009). Despite reports of some ‘good progress’ in meeting the terms of the WCCCA (Klimenko and Evans, 2009, p 5), many of the region’s Traditional Owners remain dissatisfied. Two key areas of Indigenous community concern are the current premining management practices and the outcomes of post-mining landscape rehabilitation efforts.CITATION:Annandale, M G, Castelain, G and Meadows, J A, 2016. Sustainable mining – indigenous community benefit, in Proceedings Life-of-Mine 2016 Conference, pp 173–175 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T R. Anderson, A R. Butler

Haymont (2012) notes that in parts of Australia significant areas of mining disturbance cannot be relinquished. In Queensland it has been estimated that by 2010, just 0.3 per cent 507 ha of mining disturbance had been rehabilitated to the regulator’s satisfaction (Short, 2015).One reason for this poor record is the presence of inappropriate, unachievable or unmeasurable rehabilitation targets (Glenn et al, 2014; Butler, Anderson and Sexton, 2015). In the authors’ experience in Queensland many mature operations have licence conditions that hinder the achievement of sustainable outcomes or prevent successful validation of rehabilitation success. This creates a lack of certainty for industry and a lack of confidence in the community that the sector can deliver good rehabilitation outcomes (Short, 2015).This extended abstract presents a framework approach that has been applied at two contrasting operations. Without the changes presented, the goal of progressive rehabilitation certification, reduction in financial assurance (FA) and a path to surrender at these sites would have been impossible. The framework can be adapted for use across different bioregions and commodities.CITATION:Butler, A R and Anderson, T R, 2016. Reassessing rehabilitation objectives and targets for mature mining operations in Queensland, in Proceedings Life-of-Mine 2016 Conference, pp 139–141 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By T Walsh, S R. Mudnuru

The development of lithium-ion batteries, coupled with the global trend towards electrification of transportation, has led to a dramatic increase in the demand for lithium. The production of lithium from hard rock ores is increasing, and flotation has proved to be an effective means for the beneficiation of many pegmatitic lithium ores. Clariant Mining Solutions has developed a range of novel collectors for the flotation of spodumene and other lithium ores, and this paper presents examples of some of the most recent developments. Fatty acids are the typical collectors for lithium flotation, however the grade and recovery achieved with these collectors is often below the desired level. There are also some significant drawbacks associated with the use of fatty acid collectors, such as the formation of calcium soaps which give rise to filtration problems and the need for acid washing. Several FLOTINOR products have been developed as alternatives to fatty acids. These products offer equivalent or better metallurgical performance at significantly lower dosages than fatty acids. This offers benefits to the flotation circuit as well as potentially reducing the issues associated with downstream processing of the concentrate.

Aug 24, 2022

By W Russell, P Wighton, J Franke

Recent advances in ruggedised industrial control system technology and architecture in combination with latest technologies in the fast-evolving 3D LiDAR sensor sector becoming available have enabled the implementation of sophisticated automation algorithms for mining equipment such as bucket wheel reclaimers, as published by the authors in the peer reviewed AusIMM 2019 Iron Ore conference proceedings. This paper provides an overview of a second use case for such automation technology in bulk material ports integral to iron ore operations. The real-time 3D machine-vision based port automation system described in this paper was originally developed for the BHP-Mitsubishi Alliance’s (BMA) Hay Point port. The system has seen deployment at other major mining and general ports in Australia, such as at Dalrymple Bay Terminal (DBT) (shown in Figure 1) managed by Dalrymple Bay Infrastructure Management (DBIM), Hay Point, Queensland. It has the following use cases:

Nov 8, 2021

By D L. Head

Critical risk management (CRM) has become one of the latest safety buzz terms in mining. Everyone seems to be doing it, everyone seems to know about it, yet we are still having fatalities in our industry from well understood hazards such as mobile equipment amongst others.

May 5, 2022

By S Coward, C Xu, P A. Dowd

"This paper provides an assessment of the current challenges in strategic mine planning and design and suggested approaches for addressing them. The specific challenges covered are: realistic quantification of downstream processes applied to orebody models to provide an integrated approach to mine design and optimisation modelling, estimation and simulation of geometallurgical variables and their integration into resource and reserve estimation and mine planning modelling, estimation and simulation of new variables for new forms of mining – deep mining, particularly block caving, and solution mining flexibility in planning and design to manage risk and minimise its impact information technology (IT) infrastructure and platforms for rapid online data collection, storage, access and processing.Most of these challenges require new types of data, variables, modelling and estimation methods. Foremost among the new types of variables and data are geometallurgical and dynamic rock mass characterisation variables. New types of data and data collection include rapid generation of very large amounts of online sensor data and the consequent need for rapid processing and modelling of these data.This paper outlines the challenges and strategies in each of these areas and uses examples of models and outputs to illustrate approaches and potential solutions.CITATION:Dowd, P A, Xu, C and Coward, S, 2014. Strategies for mine planning and design, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 41–50 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By T W. C Stambolie

Longwall mining is a form of underground mining and the principal extraction method for underground coal mining in Australia. The method is used in the mining of both thermal and metallurgical coal. The primary market for thermal longwall mines is that of the export market where price is governed against the Newcastle Thermal Benchmark index (globalCOAL, 2016).Australia’s thermal coal export outlook is considered moderate due to slower demand from major importing countries, as well as slowing domestic production. However, ‘Australia is projected to increase its share of world thermal coal exports and become the world’s largest exporter over the medium term as lower prices, increased domestic use and infrastructure constraints limit growth from other key suppliers’ (Office of the Chief Economist (OCE), 2016, pp 25, 58). On the contrary, and as a result of current global coal price trends, the basic economic principles of underground longwall coal mining are heavily stressed. From a life-of-mine perspective, influencing return on investment is at its greatest during project evaluation and execution. Appropriate and realistic economic assessment is paramount to ensuring the right outcomes are achieved under the current economic challenges.CITATION:Stambolie, T W C, 2016. Thermal coal industry – is longwall mining currently a life-of-mine option in Australia?, in Proceedings Life-of-Mine 2016 Conference, pp 57–61 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The adoption of new technologies is accompanied by risks that the stakeholders will wish to understand and minimise. The process of developing a dynamic simulation and the plant it will be used in provides a discipline and attention to detail that highlights and provides an opportunity to mitigate risks that will exist in a production environment. The simulations will enable investigation of what the outcome of process failures will be and the impact maintenance. Enumerating this information will enable designs to be optimised and operating and control strategies to be tested.The success of new technology is dependent on the operators and their understanding of it and the machines that use it. In this context dynamic simulations can provide training and experience without risk to personnel, equipment or production. This experience will include situations that would not be induced in a production plant for training purposes. This paper outlines a generic template for a dynamic simulation that can be used to evaluate the introduction of an emerging technology into an operating environment. It includes process flows and surge capacity, breakdown and maintenance, operator interactions and availability, push and pull production scheduling and system control.

Sep 26, 2011