Search Documents

By Borsaru M, Wylie AW

A neutron irradiation technique has been developed which is suitable for the determinat- ion of the iron and aluminium content of iron ore fines (-6 mm particle size) on a moving rubber conveyor belt. The determination of iron entails measure- ment with a NaI(Tl) gamma ray detector of the characteristic prompt gamma rays (7.64 MeV) due to thermal neutron capture in iron, while the determination of aluminium is based on thermal neutron activation analysis. For the latter a second detector must be placed down- stream to monitor the 1.78 MeV gamma radiation emitted after activation of aluminium. Although conveyor speed has no effect on the Fe measurement, it has an adverse influence on the aluminium signal, and the belt speed should not exceed 0.1 m/s if good accuracy is required. Static trials on a 460 mm rubber conveyor belt with constant ore geometry indicate that for iron an accuracy of ¦ 1.2% Fe (2a) can be achieved for crushed run-of-mine ore at

Jan 1, 1978

By R Fletcher

Pacific Hydro, a leading renewable energy company from Australia, is developing a series of cascading run-of-river hydro electricity projects in the Cachapoal Valley at the base of the Andes Mountains some 100 km south of Santiago in Chile.These projects involve extensive tunnelling and underground works. The first of these projects is called Chacayes (110 MW installed capacity) and is now under construction with Astaldi SpA of Italy and Fe Grande of Chile as the EPC contractor. Astaldi SpA also has an equity stake in the project. It involves 6 km of tunnels between 5 m and 7 m diameter, of which 2.3 km is by tunnel boring machine (TBM) (5 m diameter).This paper outlines the local and regional geology, the scope of the Chacayes project, actual tunnel excavation rates and support, and compares the decision making on Chacayes between a choice of traditional drill and blast excavation versus TBM.The paper also outlines the next project planned to be developed by Pacifi c Hydro in the valley – the 140+MW Nido de Aguila project involving a main tunnel drive of 11 km with two intermediate adits, plus a 388 m shaft and underground powerhouse. The main tunnel drives are likely to be excavated by two hard rock TBMs (5 m diameter) but will need to be able to withstand high overburden pressures of up to 1300 m.Subsequent projects in the planning stages include the downstream Coya II project with two tunnels totalling approximately 10 km, one of which may be by TBM.

Mar 8, 2011

By Shuguang L, Jing S

Computer controlled truck dispatching systems is a newly-developed technical system in surface mines with shovel-truck technology. The real time dispatching criteria, as the core of optimal truck dispatching software, are analysed and a new criterion, complex dispatching criterion, is put forward. Dispatching criteria previously proposed include: 1. `Earliest Loading' (EL) - to assign a truck to the shovel at which the truck can be loaded earliest. 2. `Max Truck' (MT) - to assign a truck to the shovel at which the truck will have the shortest waiting time. 3. `Max Shovel' (MS) - to assign a truck to the shovel which has been waiting for the longest time. 4. `Minimum Saturation Degree' (MSD) - to assign a truck to the shovel at the branch where the truck flow saturation degree is minimum. 5. `Minimum Saturation Degree with Truck Cycle time consideration' (MSDTC) - as the MSD principle, with the truck travel cycle also considered. 6. `Fixed Dispatching' (FIX) - to assign trucks to fixed shovels. A system simulation model has been set up for truck dispatching system analysis. A few surface coal mines have been selected for case studies. Equipment waiting times and shift production of the system are obtained as the main outputs of the model. Simulation results show that each dispatching criterion has its own applicable range, no one can absolutely dominate the others. For example, when under-trucked, EL and MT criterion can obtain higher production than the MS criterion; when over-trucked, it is vice versa; while for MSD criteria, better results can be obtained no matter how the truck numbers fluctuate. From the view point of shovel output balance, large fluctuations occur for EL and MT criteria, while a good balance can be obtained for other criteria. In the light of dynamic change of mining system conditions, a single dispatching criterion is not necessarily reasonable. A complex dispatching criterion has been put forward to seek the complex optimum effect. Taking the advantage of each dispatching criteria, the dispatching result of a complex dispatching criterion dominates over individual dispatching criterion and a comprehensive optimum effect can be reached.

Jan 1, 1995

By I Sherrell, R Jain

Worldwide iron ore feed grades are trending downwards and will continue to do so with the increasing difficulties of upgrading ores. This has led to operations looking for ways to capture current tailings that still contain valuable material. In the past, these were acceptable to dispose of, but this practice is no longer economically feasible. With the increasing trend of re-mining previous tailings deposits that could be decades old, new equipment designs have been introduced to upgrade current or historic beneficiation plants. These designs can effectively upgrade these tailings to saleable products.Outotec conducted test programs for upgrading iron ore tailings from flotation rejects, thickener underflow or tailings dumps on samples provided by customers around the globe. The studies utilised Outotec’s SLon vertically pulsating high-gradient magnetic separator in combination with preprocessing equipment such as low-intensity magnetic separation, screen or scrubber and flotation for downstream processing of the magnetic concentrate. A review of the equipment required to economically process these tailings is provided, along with testing data and industrial implementation examples. The effect of different operational and design parameters on Fe grade and recovery from processing each tailings sample has been highlighted.CITATION:Jain, R and Sherrell, I, 2015. Iron ore tailings reprocessing to maximise ore production, in Proceedings Iron Ore 2015, pp 149–158 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By J Ta’ala, M Handyside

Mechanical sampling from conveyors has historically been a staple in the iron ore industry when information related to chemistry, sizing and moisture is required. In order to comply with ISO 3082:2009, samples can be taken either on a mass or time basis provided no bias is introduced by periodical variation in quality or quantity. With the introduction of mechanical sample carousels, you also have the opportunity to collect samples on a mass or time basis. In order to optimise automatic sample stations in a changing production environment, BHP Billiton Iron Ore (BHPBIO) has developed a simulation model that enables the various combinations of mass–mass, mass–time, time–time and time–mass to be investigated.The sample station model can utilise actual (variable) feed rates to achieve high resolution and enables the simulation of sample size variation. Cutter speeds and other settings can then be adjusted to better optimise the performance of the sample station with regards to optimal sample size as well as ensuring the sample station is in compliance with ISO 3082. The model can also assist process engineers in adjusting settings to better optimise the sample station and reduce unwanted events such as blockages. The model can be easily modified to conform to various sample station designs. This paper demonstrates the use of the model and the benefits that can be achieved.CITATION:Handyside, M and Ta’ala, J, 2014. Simulating time versus mass basis?sampling, in Proceedings Sampling 2014 , pp 155–164 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By R Wedmaier

Henty Gold Mine is an underground operation producing 100 000 ounces of gold per annum. The original mining method used was flatbacking with paste fill. However, a non-entry method û uphole benching û was introduced in 1998 to recover the deteriorating crown pillars. Initial challenges were encountered, including poor drilling accuracy, difficulty in charging holes and poor rise performance. These challenges were overcome by a Continuous Improvement Team, consisting of mining engineers, supervisors and miners. Following this, the Team implemented further changes aimed at reducing ore loss and dilution. A second area addressed by the Team was development blasting, where innovative detonator technology known as the ExelTM DevelDetTM was introduced and rapidly accepted by the operators. Continued use of the ExelTM DevelDetTM resulted in a number of benefits, such as easier bogging, less perimeter damage, faster charging and hook-up and decreased wastage. Finally, improvements were made in the area of explosive handling, where competency-based training of operators was conducted and manual handling of ANFO has been significantly reduced by the introduction of the MiniMoverTM into the underground magazine.

Jan 1, 2001

By C M. Standen

The SAG mill at Rasp Mine has undergone a number of liner design modifications since commissioning in 2012, making liner wear and failure difficult to predict from historical data. During 2017, several instances of liner failure or near failure were experienced resulting in unplanned downtime for emergency relines or to patch liners in the lead up to a planned shutdown. The strategy for relining mills is often to minimise the frequency of relines (and subsequent shutdown costs) by extending liner life, achieved through design modifications. However, it was observed that as the Rasp SAG mill liners wear, mill performance declined with power draw increasing and throughput declining. Opportunity and inefficiency costs start to erode the revenue per additional tonne milled for a given set of liners, and in turn the benefit of delaying relines. As such, optimising the frequency of relines becomes a trade-off between reline costs and opportunity/inefficiency costs in delaying relines. The aim of this paper is to demonstrate a frame work for analysing costs using a marginal economic analysis with the assumption that the Law of Diminishing Returns can be applied to the life of mill liners. The SAG mill operating variables can be modelled to determine their impact on costs and an optimal reline point can be defined where the total costs are minimised. This prevents unexpected failures due to accelerated wear by providing justification to reline earlier and thereby allowing efforts to be focused on sustaining milling performance.CITATION:Standen, C M, 2018. An economic approach to optimising mill reline frequency – a case study of SAG mill relines at Rasp mine, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 197–206 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By D Pienaar, B McFadzean, C T. O’Connor

Collector and frother molecules in sulfide mineral flotation are thought to have separate roles in the flotation process, where the collector selectively hydrophobizes the mineral surface and the frother adsorbs onto the bubble surface, inhibiting bubble coalescence. Molecular interactions have been observed between these molecules which allow them to co-adsorb at each of the respective interfaces, improving pulp phase recovery. This study investigated the molecular interactions between sodium diethyl dithiophosphate (SDEDTP) and hexanol, and the mechanism by which these interactions improve the recovery of galena. In this study each of the respective interfaces were investigated for the adsorption of SDEDTP. The adsorption of SDEDTP on galena was measured by UV-Vis spectrophotometry and isothermal titration calorimetry. At the air-water interface foam stability and pulp bubble coalescence was used to quantitatively discern if there are interactions between SDEDTP and hexanol. Microflotation and induction time experiments were performed to determine the effect of SDEDTP, hexanol and their mixtures on mineral recovery and bubble-particle attachment. The results of all these tests were collated to determine if SDEDTP-hexanol mixtures synergistically improve sulfide mineral recovery. It was found that SDEDTP reduced bubble coalescence in the pulp demonstrating activity at the airwater interface. Together SDEDTP and hexanol synergistically enhanced foam stability. This indicated that there are attractive molecular interactions between these reagents. Even though DTP did not adsorb onto galena, DTP-frother mixtures synergistically improved the recovery and attachment probability of this mineral. Adsorption studies with aeration showed that DTP in the presence of a frother transfers from the air-water interface to the galena mineral-water interface during bubble-particle collision. It was proposed that the transfer of hexanol through the thin film enhanced the kinetics of film thinning between the bubble and the particle by destabilising the thin film thus improving pulp phase mineral recovery.

Aug 24, 2022

By J Lööw, M Nygren, E Segerstedt, L Abrahamsson

The purpose of the paper is to discuss socially sustainable development in the mining industry and the communities surrounding the mines. The discussions are based on results from a prestudy and literature review on mining and sustainable development conducted during 2013–2014 at Luleå University of Technology in Sweden. ‘A social licence to mine’ is important for the mining industry, but the social dimension is a relatively underdeveloped dimension when it comes to sustainable development in general and the mining industry in particular, one reason probably being the lack of effective methods for capturing social impacts. The mining industry and the surrounding communities face many challenges that provide both possibilities and obstacles to socially sustainable development; eg aspects such as gender, work conditions and cultural aspects. For example, a strong mining workplace culture and community identity can create strong cohesion but also lead to excluding certain groups, rejecting new ideas and reinforcing obsolete values. Other challenges include recruitment, as well as health and safety in relation to an increased use of fly-in-fly-out, contractors and automation of mining. Some challenges relate to the effects of fluctuations in the mining market. There is a lack of research that links attitudes, policies and activities within companies to their impact on the wider community, and vice versa. Future research should also include the development of methods and indicators for social sustainability relevant for mining – in other words: how do mining companies get ‘a social licence to mine’?CITATION:Abrahamsson, L, Lööw, J, Nygren, M and Segerstedt, E, 2015. How to get a social licence to mine, in Proceedings Third International Future Mining Conference, pp 125–136 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By P Hawke, J Hurst, B KrapeP

Hancock Prospecting Pty Ltd (HPPL) drilled two deep diamond stratigraphic holes (ECD0001 and RHD0296) within the eastern Fortescue Valley in the Pilbara of Western Australia. Located south of the Roy Hill Iron Ore project, the holes aimed to define the stratigraphy of the Marra Mamba Iron Formation (MMIF) of the Chichester Range and its south-dipping extensions below recent cover. Previous attempts to define the MMIF of the Chichester Range have resulted in differing interpretations due to the data available at the time.The unweathered MMIF beneath the Fortescue Valley in the HPPL drill holes is characterised by dolomitic carbonate interbedded with stilpnomelane-rich shales, chert and banded iron formation (BIF) with hematite staining. This intersection equates to ~75 m of carbonate-facies iron formation, as opposed to the ~230 m thick oxide-facies BIF and shale sequence encountered south of the Fortescue Valley.Various detailed geological core analyses and interpretations from ECD0001 and RHD0296 were integrated with regional diamond and reverse circulation (RC) holes from across the Fortescue Valley. Interpretation of the data indicates that the eastern Fortescue Valley MMIF represents a thinned thickness sequence of the whole formation. The MMIF of the Chichester Range and Fortescue Valley has gamma logs that correlate strongly in parts to the type section used for MMIF south of the Fortescue Valley. Therefore, the outcropping MMIF in the Chichester Range represents an eroded equivalent of the æreducedÆ thickness MMIF observed in ECD0001 and RHD0296.Data from deep diamond drill holes across the valley, from the Hamersley Basin to the Carawine Basin, were correlated. The correlation shows that the depositional site of the MMIF in the HPPL diamond drill holes is consistent with a proximal ramp setting, in which iron-rich shales wedge up-palaeoslope and shelf-derived carbonate turbidites wedge down-palaeoslope. Not only is it the occurrence of these shales that define the MMIF, but they also determine the northward potential to develop orebodies, as they are the source of iron from which iron-rich oxides and carbonates of metamorphic or diagenetic origin form.CITATION:Hurst, J, KrapeP, B and Hawke, P, 2013. Stratigraphy of the Marra Mamba iron formation within the Chichester Range and its implications for iron ore genesis at Roy Hill - evidence from deep diamond drill holes within the East Fortescue Valley, in Proceedings Iron Ore 2013 , pp 91-106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By F Phillips, E Deucker, J Kato

It is challenging to determine the optimal mining strategy to maximise value when a mine plan includes mineralised material which does not meet the full cost of mining but has value exceeding the variable cost of mining (‘marginal material’). Mining too much marginal material dilutes the operation’s head grade and undermines profitability. Conversely, leaving too much metal behind fails to achieve the full value of the endowment. Finding the balance between the two will maximise value delivered from the asset. This dilemma has traditionally been approached by calculating a suite of cut-off grades to define the grade of material that meets economic targets for an orebody (or zone within) and should therefore be included in the mine plan. A problem with this approach is that individual mining blocks within the zone have different costs, value and confidence levels, with each having economic co-dependencies between them. Blocks of identical grade but different mining contexts will have distinctly different economic outcomes. For example: • a block may be a low-grade increment or shell around a higher-grade stope; • a block may be available to be mined when there is spare mining capacity; or • a block may defer access to significantly higher cash flow material. Each of these circumstances would result in different value from the blocks if included as part of the mine plan. Cut-off grades calculated as averages over zones of material, or in isolation from schedule-based information, are missing the entire mining context that determines the ultimate economic outcome of making a mining decision. There are tools and techniques available to address this for open pit mining, however underground mining has different nuances. There are more intricate economic and physical dependencies between potential ore blocks, and importantly, the decision to leave material in situ can be made at any time. The case study in this paper explores a new methodology for underground mining, targeted towards strategic planning applications. It examines whether the economic logic usually applied via cut-off calculations can be implemented in the schedule so that optimal economic decisions can be made on a block-by-block basis, taking into account the mining context of the block, with the objective to maximise asset value. The results of the case study scenarios in Table 1 demonstrate the magnitude of the potential improvement in NPV that can be attained by a block by block valuation approach

Mar 15, 2021

The transition from low stress to high stress conditions is a challenge eventually faced by most mines in Australia that extend to depths greater than (generally) about 1000 m. In areas with strongly adverse 'stress versus depth' gradients, such as some parts of Western Australia, significant stress-related problems have occurred at depths as shallow as 300 m below surface. The actual depth at which the 'transition' occurs is a function of the local pre-mining stress field, the strengths of the various rock types hosting the deposit and the layout and sequencing adopted in the mine. Stress-related damage can result in increased support costs, and delays associated with rehabilitation and disruption to production. In the worst case, where strong seismicity and associated damage occurs in active mining areas, 'exclusion' zones and 're-entry' protocols may be required. These can severely disrupt production. A key aspect of managing the transition is the recognition of the onset of stress-related ground behaviour. Damage mapping can be used to develop understanding of the relationships between mining activities and the local and regional response to them. Carefully documented case histories provide a basis for calibrating numerical models. This paper discusses some of the typical styles of ground behaviour observed in higher stress conditions in underground mines. A simple damage classification scheme is described to assist in 'damage mapping' of mine tunnels. An example of damage mapping is presented to illustrate an approach commonly used for recording stress-related damage.

Nov 25, 2010

By C C. Souza, S C. Amarante, A C. Arauj

All major companies now producing iron ore in Brazil currently employ or are planning to employ some sort of concentration method to upgrade their fine sized products (sinter feed fines and pellet feed fines). The criteria for the selection of the most suitable concentration method for each application include a series of parameters; the most important among them being related to ore mineralogy. This paper reviews the concentration operations currently employed in Brazil and shows how ore mineralogy plays a fundamental role in the selection of a given method. Examples involving gravity concentration (jigs and spirals), magnetic separation (Rare Earth wet drums, ferrous wheel, and Jones type magnetic separators) and flotation (especially column flotation) are discussed. Fundamentally important for the selection of a concentration method is the mineralogy of iron-bearing minerals and gangue minerals presented to the feed to the concentration unit operation. For instance, the presence of liberated quartz as the major gangue mineral for a pellet feed size stream generally indicates that flotation will be the best selection for the concentration of that stream. However, even if magnetite is present only in the form of crystal relicts within hematite grains, it may lead to the selection of either magnetic separation alone or a combination of magnetic separation and flotation for concentrating such material. Presence of gibbsite and/or kaolinite as the major phase containing alumina will also affect the selection of the concentration method in all cases. Again for the case of pellet feed size streams, kaolinite does not interfere with flotation whereas gibbsite tends to contaminate flotation concentrate (pellet feed fines) as it is depressed together with iron oxides and hydroxides during the reverse cationic flotation process.

Jan 1, 2002

By M Gasparon, J Harris, T Baumgartl, D J. Williams, M Edraki, P A. Kirsch, D Rowe

RISKGATE, an Australian Coal Association Research Program-funded (ACARP) initiative, has been designed to assist the Australian coal mining industry in improving minimum standards for safety performance, efficiency, operating practice and training. The online system is innovative in that it is built upon a foundation of industry expert knowledge gathered through action research workshops, which is further supported by a broad array of industry, academic and technical resources. In operation, RISKGATE offers a continuum for knowledge transfer and communication of current practice in risk identification, assessment and management in the coal mining industry. The primary mission of RISKGATE is to focus industry attention on prioritising control management as a way to achieve acceptable risk.A Coal Mine Tailings Dam Module has recently been added to the RISKGATE suite. The key risk, or initiating event, associated with coalmine tailings dams is catastrophic failure of the dam, leading to the release of tailings and water. This can occur due to geotechnical instability of the dam itself or of its foundation, overtopping and erosion of the dam, and piping failure of the dam itself or of its foundation. Coalmine tailings dams are also prone to seepage into the foundation and through the dam, particularly during operation when large volumes of water are discharged with the tailings. The most significant risk associated with seepage is the release of potentially contaminated water to the environment. Contamination can take the form of elevated salinity, acidity and dissolved metals. Run-off from coalmine tailings can cause erosion and can also potentially contain contaminants. Desiccation of the tailings surface can result in dust generation and dispersion.The paper presents the background and context of the RISKGATE project, the need for the addition of the RISKGATE Coal Mine Tailings Dam Module, and a description of the developed module, including the five initiating events considered, their causes and associated preventive controls, and their consequences and associated mitigating controls. This paper concludes with a discussion of the ways in which Australia’s coal mining companies are starting to apply the RISKGATE body of knowledge at their sites, which will flow onto the management of their tailings dams.CITATION:Williams, D J, Kirsch, P A, Gasparon, M, Baumgartl, T, Edraki, M, Rowe, D and Harris, J, ?2014. Application of RISKGATE to coal mine tailings dams, in Proceedings Life-of-Mine 2014 , pp 219–230 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By S G. Gemell

"The financial model is an integral component of any project evaluation based on mineral resources, ore reserves and (at least internally) exploration targets. Given the unity of purpose for preparing financial models for project evaluation purposes, the diversity of both format and content of the finalised models is surprising. Many models are prepared by staff or consultants who are comfortable with a particular format that may be used for other purposes, such as budget preparation or financial reporting. It is natural in these situations that the practitioner will take these models and adapt them to the purpose. The end result may or may not succeed in providing a clear, accurate and sufficiently detailed view of the project’s economic viability.When preparing a model, the practitioner should be cognisant of the interpretation and review, or audit, process. The auditor may be a consultant or employee of a bank, potential equity provider or of the project sponsor itself. Depending upon the scale of the project and the level of participation of the entity that the auditor represents, the financial model will be interrogated more or less rigorously. In any event, the end user will require the model to permit easy change of inputs and will wish to confirm that such change is appropriately and thoroughly transmitted throughout.Accordingly, there are some ‘dos and don’ts’ that can be readily applied in the creation of the financial model that will greatly assist the end user, not just in the change of inputs, but also in reviewing the model’s integrity. The less time and effort required by an auditor in this regard is reflected directly in the cost of the review process.CITATION:Gemell, S G, 2016. Financial modelling with the auditor in mind, in Proceedings Project Evaluation 2016, pp 172–180 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By R Lachenicht, J Player, A Thompson, E Villaescusa

Kanowna Belle Gold Mine is a deep, high-stress, sublevel open stoping mine located near Kalgoorlie. Seismic activity during the development cycle presented problems, including concerns regarding the exposure of personnel. A number of seismic management systems were developed and tested to monitor seismicity and control the risk. It was recognised that a dynamically capable reinforcement and support system was required to be installed as part of the development cycle to reduce the risk of exposure of the underground workforce to uncontrolled movement of rock. The performance of a new Garford Dynamically capable bolt was measured in tests performed by the Western Australian School of Mines (WASM) at their Kalgoorlie Dynamic Test Facility. Detailed descriptions of the facility and data processing were reported by Player, Villaescusa and Thompson (2004) and Thompson, Villaescusa and Player (2004). The development of the Garford Dynamic bolt is described and dynamic testing results are presented and evaluated. This bolt was implemented in the mining cycle following the testing program; the observed performance is described and assessed in this paper.  

Jan 1, 2008

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.Recent increases in prices for iron ore, together with the potential to produce high iron and low contaminant concentrates, have resulted in a renewed interest in recovering magnetite from banded iron formation and other deposits.Geometallurgical evaluation of magnetite involves approaches to sample preparation, sample analysis and resource estimation that are different from the methods commonly used for haematite iron ore. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.The sampling protocol will typically include the use of Davis Tube analysis. The Davis Tube is a bench-scale test that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery.During resource modelling, the mass magnetic recoveries and concentrate grades may be assigned to a block model using regressions with other chemical constituents, or may be estimated directly. For estimation of the concentrate grades, a weighting can be applied to account for the different mass magnetic recoveries from each sample and the impact of these differences on the concentrate estimates.This paper presents an overview of the use of metallurgical test data in resource evaluation for magnetite deposits.

Jul 11, 2011

By S C. Dominy

For any gold deposit-based geometallurgical study, the collection and processing of representative samples for gold grade and recovery tests is critical. Sampling protocols should be designed to suit the style of orebody in question. The proportion and size of gold particles has a direct impact on the effectiveness of sampling protocols and metallurgical recovery processes employed. Studies focussing on ore mineralogy and gold particle deportment, size and distribution are required. Key issues are the presence of gold particle clustering (important for sampling optimisation) and proportion of coarse versus fine to refractory gold. X-ray computed tomography (CT) is a radiographic technique that produces high-resolution 3D computerised models of objects based on density distribution. The ‘virtual’ specimens are made up of voxels, the 3D equivalent of pixels each assigned a grey value based on X-ray absorption. This paper presents the results of recent research on the imaging of in situ gold particles in a coarse gold-bearing ore. The technique shows promise as a rapid non-destructive method for preliminary characterisation to facilitate more detailed studies. Early and rapid gold particle determination enables sampling protocol optimisation and metallurgical recovery parameters to be defined prior to detailed feasibility studies

Sep 5, 2011

By J E. Everett, K Jupp, T J. Howard

Simulation modelling is a practice commonly used in the mining industry to evaluate alternative process designs. Such modelling is typically undertaken as an optimisation study to increase the efficiencies, productivity and product quality of operating mines. In this situation, real short-term grade variability data of extracted ore are available from production records as input data into the simulation.There is also a need for simulation modelling to be performed before mines are approved for construction to clarify the grade variability characteristics that can be expected from the operating mine and assist in the optimisation of the process design. In this situation no historical short-term grade variability data are available. To achieve meaningful and reliable results from a simulation it is necessary to have input data for the ore to be extracted from the pits, representative of the short-term grade variability that would be expected for the operating mine.This paper describes an example of a path taken to generate realistic input data.A method described as composite cut-off criterion was used to distinguish ore from waste, which gave substantially greater recovered tonnage at target grade compared to the conventional quadrant cut-off grade criteria.The only data available for the project was resource model data in the form of kriged block models, which are known to underestimate true ore grade variability. To achieve realistic results from the simulation it was essential to increase this variability while maintaining the accurate average grades. Areas of certain deposits that were modelled using both kriging and conditional simulation estimation techniques were quantitatively compared to establish the comparative variance and the kriged data was modified to match the conditionally simulated variance.A realistic mining model was generated via a process of discretisation and regularisation of the resource blocks. Quantitative assessment demonstrated that this method adequately compensated for ore dilution and that adjustment for ore loss was not required due to an ore skin surrounding the edge blocks.The conditioned data was then used to generate a schedule of daily mine extraction, considering grade variability, tonnage, equipment constraints and extensive blended-in-blended-out precrusher stockpiles to feed into the process design simulations.For the precrusher stockpiles a number of alternative allocation criteria were examined for ore being extracted from the pits to identify the best method in achieving reduced variability through the daily scheduling system. The study concluded that a single analyte separation criterion produced acceptable variability with minimal complexity.The blending efficiency of manually stacked and reclaimed precrusher stockpiles was studied to determine a realistic blending efficiency within the pile. A recommended method of building and reclaiming was determined to give maximum blending efficiency.Finally, the data was used as input into process design simulation models; simulation from crusher feed to shiploading demonstrating that control of shipment grade variability was achievable and that the conditioning of the data delivered realistic results.CITATION:Jupp, K, Howard, T J and Everett, J E, 2013. Generating synthetic data for simulation modelling in iron ore, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 231-238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By P Toor

Due to the high energy consumption of milling, it is desirable to improve the efficiency of this process. One alternative to reduce energy and material consumption while optimising production yield in mill operation is through balanced design and selection of liners. Over-design of liners leads to increased life but at a cost to grinding performance, a relationship which to date has not been studied closely. This paper provides a description of this process of liner life cycle optimization and presents initial results from the first of two life cycles being studied for a 32 foot (ft) SAG mill. The use of commercially proven high resolution laser scanning based liner shape information provided by the MillMapper® software correlated with well controlled site surveys at various points in the liner life was used as the basis for comparison. The survey data was modelled in JKSimMet to provide direct comparisons of mill performance. This potentially provides a methodology for the design of liners that maintain a favourable shape for the majority of liner life, yielding desirable production parameters such as lower specific energy consumption and higher throughput, while at the same time maintaining practical liner life cycles.

Aug 8, 2011