Search Documents

A mechanised sub-level overhead benching method is used at Cleveland, to produce 22,000 tons per month of ore assaying 0.92% Sn and 0.40% Cu. The ore occurs in a series of vertical lenses which can be mined by open stoping. Levels are developed at 60ft., vertical intervals by jumbos. The ore is silled out and the stope block formed between levels drilled out by long hole drilling. Each row of holes is fired and broken ore within safe reach from the stope brow is mucked out by Wagner ST-5A Scoop Trams. The remaining broken ore is recovered on extraction of the next lower level. Ore is hauled by road to the crusher station from the mine. As mining proceeds below the lowest surface portal a spiral decline will be used for ore haulage and mine servicing.

Jan 1, 1970

By McGill RA

The Ranger Uranium Mine is surrounded by a World Heritage National Park. The strict environmental controls under which the mine operates are based on scientific and social requirements. Release of non-process storm runoff water to the Magela Creek during flood discharge and under controlled conditions has been identified as Best Practicable Technology for the operation of the water management system. Social and political factors have limited this release to a wet season with an Annual Exceedance Probability of one in ten. The first-generation trigger mechanism was based on a percentile analysis of monthly rainfall. The second-generation trigger is based on cumulative monthly volume increase in the retention ponds and is considered to be more applicable to the operation of the mine water management system.

Jan 1, 1988

By Cox LT

A short term tyre study of trucks operating in a multiple pit surface coal mine showed significant potential for cost savings. The tyre study, conducted on-site over a three months period covered a mixed fleet of 18 trucks ranging from 27 tonne to 77 tonne capacity operating on overburden removal, coal haulage and watering duties. Some existing plant history records and a variety of tyre related measurements during the course of the study allowed the current state of tyre operations to be quantified. Specific attention was given to determining ger>ral trends from historical records and conducting detailed studies of individual lug damage, pressure monitoring and rectification, as well as tyre maintenance procedures. Important haul road parameters including camber, gradient, curve radii and superelevation, constructional materials and surface clean-up were appraised for their influence on tyre wear. Recommendations for achieving long term cost effective tyre utilisation included increased tyre maintenance, personnel development, compliance with haul road design parameters and more stringent clean-up Procedures.

Jan 1, 1982

By Walshe JL, Solomon M

The Emperor vein system lies on the eastern margin of the Tavua volcanic structure. This is of Miocene age and occurs in basalts(the Mba Volcanics) probably underlain at about 2 km by calcite-rich sediments (the Vatukoro Formation). The lodes are generally flatmakes, or steep fault fillings, or complex shatter zones, and consist of quartz and altered wall rock. In areas of open cavities it is possible to establish a paragenesis which involves five quartz stages and two ore mineral stages. The first ore stage contains calaverite, krennerite, sylvanite and native tellurium, the second petzite, hessite and native gold. The quartz stages are thought to have formed slowly (102 years) from boiling solutions of low salinity at temperatures varying with time from about 250¦C to 190¦C. The system was sealed, the temperature gradient near vertical and the mass flux small. The ore mineral stages probably formed relatively rapidly (101years) from boiling solutions at 250¦ to 200¦C when the system was mainly open. Gold deposition was probably largely a result of fall in aH2S due to boiling, the calculated solution concentration falling from a maximum of about 8 ppb at 250¦C to about 8.10-3ppb at 200¦C. Boiling is also probably responsible for an increase in a02 (by loss of H2) and fall in aTe2 (by loss of H2Te). The fluids are thought to have had a large component of meteoric water and to have been heated by plutons in the core of the volcanic structure. Stable isotope data indicate that they derived their carbon from the underlying Vatukoro Formation and their sulphur from sediments. Circulation may have been confined to the outside of the volcanic structure because of the relatively low permeability of the flows, pyroclastics and dykes within it.

Jan 1, 1987

By Wallman D

Since 1981 two single entry roadways have been driven at Ellalong Colliery for a total distance of 1 030 metres. They were driven at a height of 1.73 metres within the 3.7 metres thick Greta Seam using a Dosco In-Seam Miner (I.S.M.). Ventilation of the drivage was accomplish- ed by an exhausting fan in series with steel ducting and flexible ducting in the immediate face area. The air quantities provided at the face were more than adequate to comply with the requirements of -the auxiliary fan rules and the Coal Mines Regulation Act, 1912, as amended. The experience gained in these drivages demonstrated that the ventilation of long single entry headings can be practically and safely achieved using existing equipment.

Jan 1, 1983

Recognition is the most important aspect in the use of breccias as an exploration tool. Ore-hosting breccias occur in a wide variety of environ-ments, shapes, compositions and characteristics, but generally present favorable loci for the deposition of ore mineralization in epithermal, porphyry copper-gold-molybdenum, massive sulfide, carbonate-hosted, sedimentary lead-zinc deposits and others.

Jan 1, 1990

In order to satisfy environmental and mine operational requirements it is becoming increasingly important to minimise ground blast vibrations at certain locations. These locations are often in soil or on large resonant structures such as grain silos, highway bridges or even the walls of an open pit. A soil monitoring exercise was carried out to evaluate the common practice of coupling vibration detectors to the ground using spikes. At a series of locations in an operating quarry the spiked array response to single blastholes was compared with that of an accelerometer array attached to a calibrated embedded mount. The results clearly showed that the spiked arrays over-estimated the true ground vibration by 46.5 per cent on average, with a maximum observed error of 99.2 per cent. These errors are considered too large for compliance monitoring where accurate vibration levels are required for comparison with prescribed limits. Although spike coupling is convenient, its use for compliance monitoring should be viewed with caution. Unfortunately, however, many manufacturers supply their detectors as spiked arrays. A structural monitoring exercise was also carried out to evaluate the vibration response of a grain silo, highway bridge and a pit wall to the initiation of single blastholes. In this case accelerometers and standard geophones were firmly attached to the bridge which resonated at low frequencies. The results clearly show that, due to their limited low-frequency response, the geophones typically measured only half the true vibration level as measured by the accelerometers.

Jan 1, 1995

Brunswick Mining and Smelting Corporation Limited operates a large base metal property near Bathurst, New Brunswick in eastern Canada. Nominal capacity for the underground mining operation and concentrator is 10 250 DMT/day. Four concentrates are produced by differential flotation technology to recover minerals containing copper, lead, zinc and silver. Two characteristics of the Brunswick ores have a major impact on mineral processing operations. The mineralogy of the ore is complex with a total sulphide mineral content of 85 per cent. In addition, the ore is extremely fine-grained, and satisfactory liberation is difficult to achieve. These characteristics directly influence flotation selectivity and thereby affect metallurgical performance. Significant improvements in metallurgical performance have been achieved through the application of basic grinding and flotation principles using conventional milling equipment. Current operating practice and the metallurgical advancements are detailed.

Jan 1, 1993

Supercritical fluids are gases compressed to near liquid densities and, as such, have unique properties compared to liquids: low viscosity; zero latent heat; high diffusivity and pressure-dependent, solvation characteristics. These properties are being utilised in new processes and current research is delineating areas where such processes may be applicable to extractive metallurgy. The processes and areas of interest are as follows: Supercritical Fluid Extraction in which substrates are dissolved at high pressure and fractionated at successively lower pressures. Areas of interest include extraction of organic materials for regeneration of activated carbon for the CIP process and for upgrading alumina industry products and, separation of transition metal chlorides. ò Supercritical Water Oxidation in which high pressure gaseous water acts as a medium in which substrates are oxidised while suspended or dissolved. This process may be of use for oxidation of organics in Bayer liquor and oxidation of mine waters etc. ò Supercritical Fluid Reactions where reactions occur in a supercritical fluid medium, particularly when the medium itself is a reactant. This may be of use in treating refractory or carbon-aqueous auriferous ores and in lower-temperature chlorination of transition metal oxides. Research is described which is aimed at chlorination and separation of transition metal oxides by two supercritical operations.

Jan 1, 1991

By Amusin BZ

The concept of rigid or yielding bolts is discussed based upon support requirements for excavations of equivalent geomechanical behaviour. The concept of equivalent geomechanical behaviour is introduced for comparison purpose where the rock mass properties are varied for a given depth (stress) so that the deformation of the roof without any support remains constant = 300mm. A simple experimental theoretical analysis for a uniform stress field acting on an axi-symmetric excavation is conducted to establish roof bolt requirements under different conditions such as width of a given excavation, time of setting of support etc. Results are presented in graphical forms.

Jan 1, 1992

By Clift N

Lead concentrate from the Isa and Hilton lead-zinc concentrators of Mount lsa Mines Limited is smelted at Mount Isa to produce a lead-silver bullion. This bullion is cast into four tonne blocks and shipped to Britannia Refined Metals Co Ltd, NorthDeet, England and to plants in Asia for refining and marketing. The traditional treatment stages at Mount lsa are sintering, smelting, and drossing and casting, with some of the sinter plant feed being pre-treated through an Isasmelt plant.A commercial scale lsasmelt based lead smelter was commissioned in early 1991.

Jan 1, 1993

By Laffin N. W

Invariably when a new plant is cammissioned operations personnel on takeover look at ways and means of reducing certain restrictions and improving process conditions. These improvements are generally of a mechanical/engineering nature with minor metallurgical alterations to fine tune and maximise recovery. Most operations are continually reviewing and updating existing equipment and equipment spares to gain the maximum performance hereby reducing operating costs. Design of current carbon-in-pulp/carbon- in-leach (CIP/CIL) plants has evolved to such a high degree that many of the medium sized plants can have a "blue printed" design from one to the next if the same engineering designer is used.

Jan 1, 1989

By Yates M. G, Rowlands A. T

Most geostatistical techniques applied to the estimation of ore reserves assume relatively unifonn grade and thickness within an ore deposit environment. In shear-hosted mineralisation this rarely occurs. The distribution of mineralisation is controlled by the kinematic and geometric variation within the shear zone. Although the kinematic variation is dependent primarily on the temperature (and consequently the depth) of formation of the deposit, the geometric variation appears to be relatively insensitive to this parameter. Shoot mineralisation is controlled either by the intersection of secoodary shear planes (brittle deformation) or the stretching lineation of the mylonitic fabric (ductile defonnation).Once the shear geometry is clearly identified, it is critical to review the distribution of grade and thickness of mineralisation. The practice of cutting high-grade intersections without reference to the shear model leads to underestimation of the amount of gold in the deposit. High-grade shoots may occur as pipe-shaped bodies within the system; their identification is essential for both resource estimation and mine planning purposes.

Jan 1, 1991

By Askew JE

The large, massive low grade gold orebody at Mount Charlotte has demanded an innovative approach to mining engineering. In the last five years several advances occurred in the areas of rock mechanics, mass blasting, blasthole drilling and truck haulage.Successive crown pillar failures throughout the life of the mine had resulted in a continuous geotechnical program, mostly utilisingconsultants. The culmination of this workwas the development of a successful crown pillar support system. Several stopes have incorporated the technique and the most notable success has been the relatively large F3 crown pillar.In hole hammer drilling was introduced to the mine in 1979, but little work had been done to develop a blasting system to suit the 165mm diameter holes. A non-electric sequential blasting system was adapted for use at themine and up to 600,000 tonnes have been fired successfully in an individual blast. Problems with ground vibration were addressed although this work remains incomplete.

Jan 1, 1984

The results of about 30 years of exploration and mining activities and research studies in the Kambalda mining district, Western Australia, have led to general agreement that the komatiite-associated Ni sulphide ores formed as a result of igneous processes (Ross, 1974; Ross and Hopkins, 1975; Gresham and Loftus-Hills, 1981; Cowden, 1988; Lesher, 1989 and many others). Despite this agreement, the controls on sulphide supersaturation and concentration of the resulting sulphide in a limited zone, remain uncertain and controversial. A major uncertainty is the source of sulphur in the ore deposits. Two principal sulphur sources have been proposed: 1. komatiite lava/magma (Hudson, 1972; Naldrett, 1973; Lesher et al, 1981; Cowden, 1988; Foster et at, 1995), and 2. sedimentary material (Groves, Barrett and McQueen, 1979; Lesher, Arndt and Groves, 1984; Lesher, 1989; Lesher and Campbell, 1993). Resolution of the uncertainty regarding the sulphur source is required for a complete understanding of the controls on ore formation, which in turn would significantly impact exploration strategies in the Kambalda mining district and elsewhere. This paper reviews the constraints on sulphur sources for the komatiite-associated Ni sulphide ores in the Kambalda mining district. The focus is on the general characteristics of the ores and surrounding rocks: individual ore deposits are not described, though specific examples are noted where appropriate. The stratigraphic and volcanic settings and geochemical (major and trace element and isotopic compositions) characteristics of the ore deposits and surrounding rocks are considered within the context of the competing sulphur source models, and future directions of research in the district are noted.

Jan 1, 1996

By Patridge A. C

Observations of coal stockpiles subject to unusual levels of instability showed that the particular coals exhibited 'gap grading', a relative lack of intermediate size particles. This led to a suggestion that fine coal particles within the pile might have been induced to migrate under the influence of water flow and to concentrate in relatively impervious layers, resulting in local water saturation and reduction of shear strength. To investigate this suggestion, a large test column has been constructed and washed coals with various levels of fines content have been subjected to a downward flow of water. Subsequent examination of the bed of coal within the column confirmed the percolation of fines and their concentration into horizontal layers, and showed the development of zones of saturation above those layers. Shear box tests showed differences in cohesion and internal friction angle between coals with different percentages of fines, supporting the hypothesis that fines percolation may lead to decreased stability.

Jan 1, 1995

The use of teleoperation in mining is increasing due to requirements to improve safety and reduce the number of people required to work in remote and difficult environments. We recently completed a project to develop a teleoperated control system for a rock breaker at an iron ore mine in the Pilbara region of Western Australia, with the objective of demonstrating the feasibility of remote rock breaking over long distances. This required controlling both the rock breaker and an array of pan-tilt-zoom (PTZ) cameras using joysticks. Controlling the cameras distracted operators from the primary task of controlling the rock breaker to position and fire the hammer. This lengthened task times as both the operator's attention and their hands have to swap between different control interfaces. In this paper, we present a novel design using human eye gaze as an interactive input for the remote camera control. It follows a simple and natural design principle: Whatever you look at the screen, it goes to the centre. A prototype system has been implemented by integrating computer vision based eye tracking technology, with the advantage of being real-time, robust and marker-less. We conducted a user evaluation, where users undertook a control task while obscuring the direct view of the working area and using a remote camera to transfer the live video stream as the visual feedback. Subjects were required to participate in the experiment using eye tracking camera control and traditional joystick control respectively. The statistical analysis of objective measures indicated that our novel eye tracking control significantly outperformed the joystick control. The results of the post-experimental subjective measures also revealed much higher user preference for using eye tracking control, which provides clear evidence that this design is a better interface for remote camera control in mining teleoperation settings.

May 1, 2010

By Lorenzen L

In South Africa, as in many other countries, the young engineering graduate is promoted quite soon to a management position where he uses less technical skills and more people-oriented skills. In the standard undergraduate curriculum for engineering, little attention is paid to the non-technical issues of the profession. An undergraduate course in management techniques cannot be a substitute for a MBA or Masters degree in engineering management, but can at least create an awareness of the practical problems facing the engineering manager. The aim of this paper is to provide an outline of such a course structure at the University of Stellenbosch. A survey is also presented on management training in the South African and Australian mineral industries. Feedback from students and graduates indicates that the fresh graduate does not fully appreciate the value of such a course until he/she achieves a position of responsibility after two or three years. Nevertheless, the management course appears to be successful in widening the perspectives of the engineer. As explained frequently in management journals, the technically oriented person (the engineer) has a convergent thought pattern, which could be in conflict with the more divergent thought pattern of the top, personnel or marketing manager. It becomes increasingly imperative for the young minerals engineer to be externally oriented instead of the traditional internal focus of engineering. The engineer should not only be aware of environmental issues in the technical design and operation of plants, but should also understand the inter-relationship between public relations, political pressures and environmental perceptions vis-d-vis technical facts.

Jan 1, 1993

By Large RR

Precious metals in the Rosebery north-end orebody occur predominantly in sphalerite- galena-pyrite ore and to a lesser extent in massive barite mineralisation. Gold may also occur in the upper parts of pyrite-chalcopyrite ore (although this ore type is usually gold poor), in pyritic mineralisation lateral to base metal sulphide lenses and in the footwall (very patchy). Although present, remobilised precious metals do not occur in economically significant quantities. Mineralogically, silver occurs dominantly in tetrahedrite and, to a lesser extent, argen- tiferous galena. Gold occurs as electrum associated dominantly with pyrite and, to a lesser extent, tetrahedrite. Geochemical modelling suggests that silver was probably transported as a chlorocomplex, while gold was transported dominantly as a thiocomplex, although at high temperature gold was transported as a chlorocomplex.

Jan 1, 1987

By Liu Q, Siefken T. C, Misra V. N

Investigation of the differential flotation characteristics between arsenopyrite and pyrite in a ore concentrate have been carried out on a laboratory Leeds flotation cell. Experimental results indicate that some limited separation between arsenopyrite and pyrite is possible by differential flotation under the conditions of high pH and low pulp redox potential. The best performance in this testwork was achieved by using an oxidizing agent at pH 10.7. Of the oxidizing agents tested, NaOCI gave better oxidizing effect than KMnO4. It has also been observed that the pulp redox potential depends on the pulp pH value. At high pH values a hydroxide layer is formed on the arsenopyrite surface, which has the effect of a depressant on the arsenopyrite.

Jan 1, 1992