Search Documents

By Harold Margalin, Elmars Ence

M. H. Mueller, M. V. Nevitt, and H. W. Knott (Argonne National Laboratory)—We have reported1 the crystal structure of Ti2CU as body centered tetragonal with a. = 2.944A and co = 10.786A, six atoms per unit cell, and space groupl4/mmm(MoSi2 type). This cell is larger but definitely related to the unit cell reported by the authors. It permits definite positions for the titanium and copper atoms in the cell located as follows: 2 Cu (a) 0 0 0; 1/2 1/2 1/2 4 Ti (e) 0 0 z; 1/2 1/2 1/2 + z; 0 0z; 1/2 1/2 1/2- z where z = 0.341 The face centered tetragonal cell reported by the authors can be transformed to a small body centered tetragonal cell with flo (small bet) = ao(fct)v2 Both unit cells have the same CO. Neither the face centered tetragonal cell with four atoms per unit cell nor the small body centered tetragonal cell with its two atoms per unit cell lend themselves conveniently to an orderly arrangment of the 2 to 1 ratio of titanium to copper atoms. When the co of this small body centered cell is tripled, however, a large body centered tetragonal cell results with six atoms per unit cell as described above. We had also noted that the X-ray patterns of Ti2Cu indicated that the structure could be approximately described by the face centered tetragonal cell as reported by the authors; how- ever, there was evidence for a few additional very weak lines whose positions indicated a larger unit cell. Since the X-ray scattering amplitudes of titanium and copper are nearly equal, it is evident that it is difficult to distinguish their positions especially from X-ray powder patterns. It was therefore decided to look at a powder pattern obtained by neutron diffraction since the scattering amplitudes of the two elements are considerably different in magnitude and opposite in sign. The sample used for neutron diffraction was selected from a group of three alloys prepared by arc melting using crystal bar titanium of 99.92 pet nominal purity and 99.999 pet pure Cu. The alloys designated as A, B, and C had the following respective compositions: Ti-32.8 at. pet Cu, Ti-33.3 at. pet Cu, and Ti-33.8 at. pet Cu. On the basis of the melting losses incurred, it was established that the actual concentration of either component in any of the alloys probably did not deviate from the intended value by as much as 0.1 at. pet. The alloys were annealed for 5 days at 700°C in evacuated Vycor capsules and quenched in tap water. The metallographic structures of these alloys are shown in Fig. 1. None of the alloys contained sufficient second phase to permit its positive identification. Since alloy B contained the least amount of second phase and since its composition placed it closest to the ideal stoichiometry, it was chosen for the neutron diffraction study. The oxygen content of alloy B was found by chemical analysis to be 0.06 at. pet. This particular intermetallic compound is especially suitable for investigation with neutron diffraction since if the titanium and copper atoms have a random statistical distribution, a near null-matrix would result in which there would be practically no coherent scattering of neutrons, and hence no Bragg diffraction peaks. Such a condition could come

Jan 1, 1962

By P. Schwarzkopf, J. H. Brophy

A modification of the Mendenhall wedge blackbody1 has been used to determine solidus temperatures and to anneal alloys in the tantalum-rhenium binary system. The technique has proven to be simple and accurate with modest power requirements. For temperatures up to 2800° C a piece of 10-mil tantalum sheet was folded double and formed as shown in Fig. 1. The middle of the resulting ribbon filament was a cylindrical-shaped crucible with less than a 1/8-in. opening. After inserting a specimen in the cavity, the filament was clamped between molybdenum electrodes in a high vacuum chamber. A representative filament 2 in. long and % in. deep was heated to 2800°C with a current of 700 amp at 4 v. The specimen temperature was determined by sighting into the cavity with a Leeds and Northrup optical pyrometer. The twisted filament shape was necessary to avoid serious geometric changes during thermal expansion. For temperatures between 2800" and 3000°C a 4-mil tungsten filament was employed. To facilitate fabrication it was warm-folded, and a twisted segment of 10-mil tantalum was used to support one end to absorb thermal expansion. This element assembly required about 700 amp at 10 v to reach 3000°C. Two geometric modifications of the filament were helpful for solidus temperature determinations. A shallow chamber, with depth to opening ratio of 3 to 1, permitted direct observation of the specimen through the optical pyrometer. The fact that the specimen was visible permitted the melting point to be determined when sharp features on the specimen surface became rounded; it also indicated that blackbody conditions did not prevail. By standardizing against the melting point of molybdenum, the observed melting temperature was corrected by the following form of Wien's Law: in which T is the true temperature, To is the observed temperature, and K is a constant characteristic of the filament geometry and determined experimentally for the molybdenum standard. The resulting corrected melting point for each alloy served as a reference temperature for the second more precise filament geometry. With a 6 to 1 depth to opening ratio, the specimen was indistinguishable from the filament interior, indicating good blackbody conditions. Using this technique, a series of specimens was isothermally treated at temperatures above and below the corrected direct reading. Incipient melting was detected by visual or micrographic examination of the specimen after cooling. This procedure was checked with specimens of pure chromium, molybdenum, and tantalum. Table I represents the values obtained, together with the solidus temperatures in the tantalum-rhenium binary system determined by the same technique. The alloy specimens were approximately 1/8 in. in diam. They were pieces of 10-g buttons melted four times in a nonconsumable tungsten electrode arc furnace on a water cooled copper hearth in 2/3 atmos of titanium gettered helium. Several sources of error are possible in such temperature measurements. Within the accuracy of the pyrometer no gradients were detectable near the specimen, and element distortion was virtually eliminated by twisting the tantalum. Compensation was made for the 1/8-in. sight glass by inserting several identical thicknesses and extrapolating to zero thickness. As a result an additional 10°C correction was added to all observations in the temperature range of 2500" to 3000°C. The principal source of error was then in the operation of the

Jan 1, 1961

By O. N. Carlson, D. G. Alexander

THE hardness anisotropy of metals and alloys has been of increasing interest in recent years but silicon ferrite,1 niobium,2 and tungsten3,4 are the only bcc metals about which this type of information has been reported. This investigation was carried out on vanadium and chromium single crystals in an effort to determine to what degree the hardness variations observed in these metals are due to orientation effects and to compare their behavior with other bcc metals. In earlier work the authors had observed a small angular dependence in the Diamond Pyramid Hardness of single crystalline vanadium on the (100) plane but no anisotropic effects were noted on either the (110) or (111) planes. At the suggestion of R. G. wheeler5 it was decided to investigate this effect in greater detail using the more asymmetric Knoop indentor. The vanadium metal used in the study was prepared by the aluminothermic reduction of V2O5 followed by electron beam melting.6 The principal analyzed impurities were 230 ppm C, 230 ppm O, 65 ppm N, 90 pprn Al, Cr not detected, 50 ppm Fe, 60 ppm Ni, and 200 ppm Si. The chromium was an iodide-refined product obtained from the Chromalloy Corporation. Analysis of this material showed the following amounts of impurities present: 10 ppm C, 9 ppm O, 2 ppm N, 0.4 ppm H, 3 ppm Al, 2 ppm Ca, 2 ppm Cu, 20 ppm Fe, 1 ppm Mg, 0.3 ppm Mn, 1 ppm Mo, 3 ppm Ni, 10 ppm Si, and 1 ppm V. Single crystals of both metals about 1 cm in diam and 10 cm in length were grown by an arc-zone melt- ing technique.7 The chromium crystal was annealed at 1600°C for 6 hr in a purified argon atmosphere to remove any strains or inhomogeneities, but the vanadium was tested in the as-grown condition. The crystals were oriented by the Laue back-reflection method and then sectioned with a spark cutter into individual specimens with a (loo), (110), or (111) plane parallel to the crystal surface. They were mounted in Lucite and carefully ground to a flat surface. The vanadium specimens were then electropolished in a 6 pct perchloric acid-methanol mixture while the chromium specimens were mechanically polished on a Syntron vibratory polisher using an alumina abrasive. The orientation of each crystal was then rechecked by the back-reflection X-ray method. All of them were found to lie within 2 deg of the desired orientation with the exception of the (110)-Oriented chromium crystal which was within 4 deg. Microhardness impressions were taken at 10 deg intervals from the common (110) direction by rotating the crystal in the plane of the crystal surface. A Knoop indentor was used with a 400-g load on the vanadium crystals and an 800-g load on the chromium. The hardness values are averages of 6 impressions and standard deviations were calculated for each set of data. The values reported for the (111) plane of vanadium are based on from 10 to 15 measurements for each point. The microhardness results for vanadium and chromium are plotted as a function of the angular rotation of the long axis of a Knoop indentor from the (110)

Jan 1, 1970

By S. M. Brisbane

THE life of refractory linings in rotary cement kilns can be shortened by uneven or inadequate support of the kiln and its shell and by variations in the conditions of operation. Alteration of these factors may, according to their nature, bring about mechanical deterioration of the lining or promote chemical attack. Chemical attack has been described elsewhere.1-4 The distortion of cement kilns has been discussed in a general manner by Rochow,6 ho indicates the amount of distortion which may occur in an unlined shell, and by Rosenblad: who states that the deformations of the shell are greatest above the trunnions. The present article indicates the extent of the distortion of a kiln to an oval shape in certain selected positions and the deviation from a straight line of the kiln along its length between two supports. The cement kiln is a long, hollow, rotating cylinder consisting of steel plates which may be either welded or riveted together. This shell is supported on tires, frequently 60 ft apart, which roll on trunnions. The large mass of the kiln causes distortion of its cross-section; it becomes slightly oval, i.e., diameters lengthen as they become horizontal and shorten as they become vertical. There is also a tendency for the shell to bow between supporting tires; this bowing may be upwards or downwards depending on the position of the weight forces and the supports. The extent of the deviations from the ideal kiln shape was investigated. Observations described in this paper were made on the shell of the clinkering zone between the first and second tires of two of the kilns at the Geelong works of Australian Portland Cement Pty. Ltd. The kilns were both 400 ft long and 10 ft diam with a welded enlarged burning zone 11 ft 6 in. diam. The shell was fabricated from mild steel and in this section its thickness was 1 in. It was lined with 41/2 in. of chemically bonded magnesite-chrome bricks which were jointed with mild steel plates. The kilns operate on a 4 pct slope and the speed may be varied between 0.75 and 1.68 rpm. The wet process is used; kilns are coal fired and are fitted with integral coolers. Temperatures within the kiln are difficult to determine with any accuracy because of the absence of black body conditions, but surface temperatures are probably in the range 1420° to 1470°C. Average shell .temperatures at the two positions at which the deformation studies were made were 370°C and 355"C respectively. Methods: In determining the ellipticity it was necessary to measure the lengths of the vertical and horizontal diameters while the kiln was in operation; data obtained from a stationary kiln would not have the same practical significance. For this purpose the four points V, W, X, and Y at the ends of two mutually perpendicular diameters were marked on one kiln. The point X is shown in Fig. 1. For the measurement of the length of the vertical diameter a vertical column, to which a horizontally aligned telescope was attached, was placed 10 ft from the kiln. The telescope could be racked up and down in a vertical plane. Two sets of readings were taken, one set when each of the points V, W, X, and Y was at its maximum height above the

Jan 1, 1957

By E. S. Bumps

A series of macrographs are presented for the purpose of graphically recording the strain phenomenon that accompanies the energy transition in the Charpy impact testing of a mild steel that is susceptible to strain aging. STRAIN patterns in mild steel Charpy impact specimens were obtained in order to determine whether, on the first appearance of plastic strain during deformation, the initial fracture cracks appear in the region of plastic strain or in the elasti-cally deformed regions between. Although this attempt to locate the initiation of cleavage was not successful, the observed strain patterns illustrating various stress conditions in partially deformed Charpy specimens are presented along with a discussion of the possible dependence of transition energy on the yield phenomenon. Earlier work on the development of strain patterns in mild steel have been reported by Fry1 and later by Jevon.2 Harris, Rinebolt, and Raring3 observed characteristic strain markings on the surface of Charpy V-notch impact specimens fractured above and below the transition temperature which they presented schematically. It is intended that the strain figures presented here will add to the literature a graphic correlation of strain with transition energy in impact specimens. Samples of % in. round hot rolled, 0.20 pct C steel were machined to standard 0.394 in. sq, V-notch Charpy impact specimens. Preliminary testing involved determination of transition temperature, Fig. 1, using a Sontagg impact tester. These data were subsequently used to select temperatures above, within, and below the transition range at which specimens were partially deformed. Partial deformation was obtained by either varying the energy or the testing temperature, see Table I. Macroscopic strain figures shown in Figs. 2 to 19 were produced by several metallographic repolish-ing and etching steps. The macroetchant used was as follows:4 120 g HCl, concentrated; 100 ml water; and 90 g cupric chloride. Strain figures were obtained on the outer surface and on sections through the central portion of the impact specimens in order to determine an approximation of the volumetric strain pattern. In the tensile strain figures reported by Jevon, it was found that strain etching would not work immediately following strain unless the material was heated to 200°C. The impact strain patterns presented here were obtained without this heating, but the specimens were not etched until ten months after straining. This confirms a discussion of Jevon's paper, in which it was pointed out that strain figures can also be developed after aging for long periods of time at room temperature. Hardness of the strained and unstrained portions, revealed by the etched pattern, was explored using R, impressions converted to R, hardness values. Discussion of Results In the impact test, as in the tensile test, some parts of the specimen yield and deform plastically, while other regions are deformed only elastically. The plastic deformation bears a relation to the imposed stress pattern. In the strain figures presented here, the plastically deformed regions are the dark etching ones. The strain figures are always symmetrical because the stress state in the Charpy-type specimen under impact loading is symmetrical. The difficulties encountered to produce initial cracks are intimated in Figs. 2 and 4. At a temperature of —75ºF, the stress was not sufficient to pro-

Jan 1, 1953

By R. V. Colligan

[CONTENTS PACE Educating and Training Economic Geologists of the Future. By C. H. BEHRE, JR. (TP 2278, Min. Tech., Nov. 1948. Discussions by R. V. COLLIGAN and EVAN JUST) ....... I Mercury Industry in Italy. By EDWIN B. ECKEL. (TP 2292, Min. Tech., Jan. 1948. Discussion .............................. by C. N. SCHUETTE) 3 Chert in the Kingsport Formation at Mascot, Tennessee. By ARTHUR T. ALLEN. (TP 2299, ............... Min. Tech., Jan. 1948. Discussion by M. M. BUTLER) 5 Wall Rock Alteration at Butte, Montana. By RENO H. SALES and CHARLES MEYER. (TP 2400, Min. Tech., May 1948. Djscussions by C. D. HULIN, W. D. JOHNSTON, JR., and L. C. ................................... GRATON) 5] Educating and Training Economic Geologists of the Future R. V. COLLIGAN*-I can best illustrate my opinions by drafting another five year plan (Table 2). This plan is set up following the same stipulations outlined by Dr. Behre, namely: (I) the student is preparing himself for commercial work as a mining geologist; (2) he is attending an institution with a sufficiently broad curriculum (that is, engineering school and mining school as well as liberal arts college) to furnish the courses listed; and (3) he is not planning to continue his studies through to a doctor's degree before going into commercial work. A comparison of my study plan (Table 2) and that submitted by Dr. Behre (Table I) will at once point up the basic similarity, due to the obvious fact that there are so many essential courses which must be included in any outline of study. However, a more detailed analysis will show up certain differences, which, in fact, are only certain refinements on Dr. Behre's program. These I plan to discuss in order of their importance. The first and most important change is the addition of 12 hr of optional subjects, making a total of 24 hr of optional subjects as against a total of 12 hr under Dr. Behre's schedule. This of course entails the elimination of certain courses, which I shall discuss later. However, I wish to make it clear that I suggest eliminating these courses not because I feel that they are unnecessary, but rather because I feel the optional courses are more necessary to the complete education of the individual. I appreciate that Dr. Behre recognizes the importance of the cultural side of education, but I take issue with his thesis that the student will get it without credit and in his spare time. I do not think that the average college student, and certainly not the college freshman, is mature enough to know what he needs and where to get it in his spare time. I think it must be "spoon-fed"; he must be oriented through specific courses. University life (or should I say "college life") is too full of athletics, fraternity activities, dances, "bull sessions," and countless other enjoyable distractions, all of which contribute to the "full man." I fail to see how the average young American male can possibly sandwich in a necessary complement of "cultural activities" in his spare time. Since these latter activities do not fall within the pattern set by the "group," and show less promise of immediate return in enjoyment, or increased social status on the campus, they are bound to suffer in competition with the more popular, "group" activities. No doubt much of the criticism levelled against arts colleges, namely, that the cultural courses are useless, is well taken, for the culture

Jan 1, 1947

By Arthur Knapp

The practical application of mud-laden fluids in wells has been the subject of many papers.' However, there seems to have been little investigation of what actually happens when mud-laden fluids are applied to a loose porous sand. The assumption is that the fluids penetrate the sands and that there is some plastering action. The degree of penetration and the relation of plastering action to wall stability is not generally known. This paper describes a series of experiments made in an attempt to observe, in laboratory apparatus, the action of mud-laden fluids under conditions simulating those to be found in a well. For the purposes of this discussion all fluids containing solid matter in suspension are mud-laden fluids. Series I: Penetration of the Pores of Uncemented Sands The subject of the penetration of porous formations by water is discussed in detail in Water-Supply Paper No. 67 of the U. S. Geological Survey. No attempt was made to repeat the experiments described therein. The results of the first experiment of this series are given simply to show the capacity of the apparatus used. The conditions in this first experiment were maintained throughout the remainder of this and the second series, except where noted. The experiments of Mills, McCoy, and others on subsurface flows, adjustments, migrations, etc., deal with the oil, water or gas within the porous beds.V he experiments described herein deal with the conditions immediately surrounding the bore hole.

Jan 1, 1923

By Arthur Knapp

The practical application of mud-laden fluids in wells has been the subject of many papers.' However, there seems to have been little investigation of what actually happens when mud-laden fluids are applied to a loose porous sand. The assumption is that the fluids penetrate the sands and that there is some plastering action. The degree of penetration and the relation of plastering action to wall stability is not generally known. This paper describes a series of experiments made in an attempt to observe, in laboratory apparatus, the action of mud-laden fluids under conditions simulating those to be found in a well. For the purposes of this discussion all fluids containing solid matter in suspension are mud-laden fluids. Series I: Penetration of the Pores of Uncemented Sands The subject of the penetration of porous formations by water is discussed in detail in Water-Supply Paper No. 67 of the U. S. Geological Survey. No attempt was made to repeat the experiments described therein. The results of the first experiment of this series are given simply to show the capacity of the apparatus used. The conditions in this first experiment were maintained throughout the remainder of this and the second series, except where noted. The experiments of Mills, McCoy, and others on subsurface flows, adjustments, migrations, etc., deal with the oil, water or gas within the porous beds.V he experiments described herein deal with the conditions immediately surrounding the bore hole.

Jan 1, 1923

By V. F. Swanson

At the AIME meeting in Tampa in Oct. 1966, an empirically developed equation was presented which allowed the calculation of free settling velocity for any sized particle: 1 [ ] This equation requires the use of two parameters a and p which are coefficients derived from boundary layer theory.2 It was possible to develop values of a and p for several minerals by back calculation of published data. The original equation had one major flaw. When the fluid density exceeds the density of the solids, the solution to the equation becomes imaginary. A flaw was indicated also by the fact that galena and sylvite both having cubic cleavage, did not have similar values for a and b. Galena gave calculated values of a = 1.082 and g = 3.11, while sylvite gave values of a = 1.870 and p = 2.56. These flaws prompted further study of the equation, resulting in the following empirical modification: [ ] It is obvious a real solution of the equation is possible for all values of ps and p. When PL > PS, V is negative, indicating that the particles will rise against the attraction of gravity. The validity of the modification is borne out by the fact that when values of a and p were back calculated for galena and sylvite using the modified equation, both minerals gave values of a = 1.038 and p = 3.01. With the modification shown in Eq. 2, Newton's friction factor becomes [ ]

Jan 1, 1976

By Thomas T., Read

THROUGHOUT the Colonial era, Philadelphia was easily , the leading city of North America, and it still held that position at the end of the period, with a population of about 25,000, though closely pressed by Boston, which had slightly over 20,000, and New York, which had nearly as many. It was the center of a region in which mineral industry was important. Thomas Rutter's bloomery, built in the Schuylkill valley in 1716, was quickly followed by many others, and during the Colonial period at least 20 blast furnaces, 45 forges, and iron- works of other types were built in eastern Pennsylvania, which easily led all the other colonies in iron manufacture. During the Revolutionary period others were erected as far west as Fort Loudon, in the Cumberland c alley.^ After 1800 the rapid development of the anthracite mining industry profoundly affected Philadelphia's, development, since transportation of the coal was then necessarily by water, and the streams of the anthracite . regions mostly flowed into either the Schuylkill or the Delaware Rivers. With an abundant near-by supply of coal and iron, with the seat of government, which had been there since 1774, and with a National Bank established there in 1791, one would have seemed safe in prophesying, at the beginning of the nineteenth century, that Philadelphia would permanently remain the leading city of the United States. Education in Philadelphia was at first wholly in the hands of the Quakers, who had established a "Public School" there in 1689, but in November 1739 George Whitefield, who had created a sensation in England by his preaching, though only 24 years old, passed through Philadelphia on his way to Georgia to found an orphan school there. He preached a series of sermons in Christ Church that were so disturbing to the established church that on Nov. 25 the Rev..Richard Peters (who was also Provincial

Jan 1, 1941

By S. Usui, I. Iwasaki

The effect of pH on the adsorption of dodecylamine at the mercury-aqueous solution interface was investigated by differential capacity and electrocapillary measurements. With dodecylammonium acetate, the differential capacity curves showed two desorption peaks in the cathodic branch with their relative intensities varying with the solution pH. With dodecyltrimethylammonium chloride, only one cathodic de-sorption peak was observed in the same pH range. Through thermodynamic analysis of the electrocapillary curves, the adsorption density of undissociated amine was evaluated separately from that of aminium ion. The adsorption densities of the un-dissociated amine and of the total amine increased with increasing pH. The ratio at the interface of undissociated amine to aminium ion was several orders of magnitude greater than the ratio in the solution and increased with increasing pH. The potential at the closest distance of approach of counter ions to the mercury surface was compared with values of zeta potential on quartz previously reported. The most important variable in the flotation separation of minerals is probably the pH of the pulp, and a number of theories have been proposed to explain its effect on the condition of the mineral surfaces, on the dissociation of collectors and of inorganic and organic species (accidentally present or intentionally added) in the pulp, and on the mineral-collector interaction. In the development of a theoretical background for oxide flotation systems, an experimental approach based on electrokinetic measurements has been of much value, although the effect of pH becomes confounded since it governs both the electrochemical conditions of the oxide surface and the dissociation of the collector. For investigation of the adsorption behavior of long-chain collectors on oxide minerals, however, electrokinetic potential measurements are the most widely used technique. Hydrogen and hydroxyl ions are found to be the potential determining species, thereby governing the interfacial electrical conditions. The electrostatic interaction between the charged mineral surfaces and ionized collectors is regarded as the driving force for the adsorption of the collectors. An association of alkylamine collectors adsorbed on quartz surfaces has been postulated from streaming potential measurements, and a term "hemi-micelles" has been proposed.' The possibilities of coad-sorption of undissociated amine along with aminium ion has been inferred from contact angle measurements? and from adsorption studies.~ Electrochemical titration as applied to silver sulfide provides a more quantitative approach to the analysis of the electrical double layer at an ionic solid-solution interfaceqG and the electrochemical evidence for the adsorption of amine at pH 4.7 indicates a specific affinity of dodecylammonium ion towards silver sulfide surfaces, whereas at pH 9.2 the adsorbed species might be free arnine." A combination of differential capacity and electrocapillary measurements on a dropping mercury electrode was reported to be a sensitive method of provid- ing reliable information on the adsorption behavior of dodecylammonium acetate (DAA) at a natural (near neutral) pH.? It was also shown that there were striking similarities in the properties of the double layer and in the adsorption behavior of the amine on mercury and on such ionic solids as quartz, silver sulfide, and silver iodide. The effect of pH on the differential capacity curves at a mercury-sodium fluoride solution interface has been investigated by Austin and Parsonss who reported that between pH 7 and pH 11 there was very little effect. In the present paper, the adsorption behavior of DAA was investigated as a function of pH through differential capacity and electrocapillary measurements and the information gathered was correlated with that available in literature on quartz and silver sulfide. Experimental The apparatus and the method used for determining the differential capacity and the electrocapillary curves were identical to those described previously.' The ionic strength of the supporting electrolyte was fixed at 0.1 M with potassium fluoride, and the pH of the solution with potassium hydroxide. Only the neutral to alkaline range was covered in order to avoid the dissolution of the glass vessel with hydrofluoric acid. Results In Fig. 1 the differential capacity has been plotted against the applied potential at a DAA concentration of 10-' M at three different pH values. The curves are characterized by one capacity peak in the anodic branch, by two capacity peaks in the cathodic branch, and by a marked depression in capacity between the peaks. The depression indicates an adsorption of the arnine in this potential range. One of the cathodic peaks appears at pH 7.3 near -1.4 v and decreases with increasing pH. The other appears at pH 8.9 near —1.2 v and increases with increasing pH. At pH 9.6 only the latter peak is observed. Beyond the cathodic peaks, all the curves tend to converge with the curve in the absence of DAA, implying that two different species are being desorbed in this potential region. The anodic peak near 0.0 v increases markedly with increasing pH. The well-defined anodic peaks at pH 8.9 and 9.6 were accompanied by an appreciable increase in the current flow (in excess of O.luA), and, therefore, is a "pseudo-capacity"'" due to a

Jan 1, 1971

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite 'is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. ' As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By John F. Wiggert

DURING the early years of Homestake operations, shaft signaling from the cage tenders to the hoisting engineers was done by mechanical means. Small steel cables or jointed steel rods were suspended in the shaft compartments and counterbalanced with weights or springs. These cables or rod strings were connected to the mechanically operated gongs at the engineers' stations by means of bell cranks and steel wires. The system was simple and economical and served the purpose well until the mine reached a depth of 1000 ft., then the system became slow and cumbersome and required a considerable amount of muscular effort to operate it with much speed, because of the inertia of the heavy moving parts. The mechanical signaling was superseded by a simple electrical system consisting of a single pair of wires in steel conduit for each shaft compartment. In the shaft at each station a pull switch was connected to the wires. The switches were operated by means of bell cords, which extended from station to station. This electrical system was a great improvement over the mechanical one, but it had one serious drawback, which also applied to the older system; namely, the engineer did not know where a signal originated. Later on this signaling was improved to overcome this drawback, and to give the engineer a positive indication of a signal's origin. In this system a separate return wire from each pull switch is carried to an annunciator at the engineer's station, where it indicates the signal's origin. While the annunciator system used by Homestake is very safe and reliable, it has the inherent drawback of all wire-connected systems in that it is impossible to send a signal from a moving cage. A number of years ago Homestake became interested in the possibility of using some sort of radio transmission for shaft signaling. The company did much experimental work with purely radio signal transmission, but no practical way was discovered to use radio transmission in a mine shaft for signaling to or from a cage. Therefore, all efforts were directed to devising a practical way of using the hoisting rope as part of the circuit. It was realized that the return circuit from the rope would need to be through electrostatic coupling between the cage and the earth or ground sides of the shaft, because the guides would not always be wet enough to make possible good electrical contact between the cage and earth, therefore relatively high-frequency alternating current was chosen as the medium of transmission. Soon a practical system was developed for transmitting an electric current from a moving cage over an electric circuit of which the hoisting rope was a part. A high-frequency electric current is used as a carrier to transmit the signals or mes-

Jan 1, 1941

By Dorsey A. Lyon, Robert M. Keeney

Page I. Introduction..........234 I1. Chemistry oF Copper Smelting...235 1. Native Copper Ores.......235 2. Oxide and Carbonate Ores....235 3. Sulphide Ores.......236 (a) Elimination of sulphur ...236 III. Reverberatory Copper Smelting...237 IV. Substitution of the Electric Furnace for the Reverberatory Furnace..................... 238 V. Smelting of Fine Michigan Native-copper Concentrates in the Electric Furnace.................. 239 1. Conclusions.................240 VI. Proposed Process for Electric melting of Fine Native-copper Concentrates.................. 241 VII. OrdINary Copper Blast Furnace 'Smelting......... 245 1. Prerequisites.................. 245 2. Losses .................... 247 VIII. Experimental Data on the Electric Smelting of Raw Sulphide. Oxidized and Carbonate Ores............. 248 1. Vattier's experiment................ 248 2. Wolkoff's experiments................ 249 3. Experiments of Stephan.............. 250 (a) Conclusions of Stephan ............ 251 IX. Smelting of Sulphide Ores in the Electric Furnace...... 251 1. Ores Treated.................. 252 2. Conclusions................... 253 X. ELectric Furnace vs. the Reverberatory Furnace and Blast Furnace as a Melting Agent.............. 253 XI. Smelting of Sulphide Ores without Roasting or Partial Pyritic Smelting............254 XII. The Electric Blast Furnace vs. the Copper Blast Furnace for Partial Pyritic Smelting.......259 1. Metallurgical conditions......259 2. Mechanical considerations......259 3. Comparison of costs.......260 (a) General considerations .....260 (b) Cost of plant........260 (c) Amount of electrical energy...260 (d) Cost of smelting.......261 (e) Cost of electrodes........262 XIII. The Use of the Electric Furnace in the Smelting of PyRITIc ORES : 262 XIV. Summary...................... 264

Jan 1, 1914

By J. J. Demo

The effect of aluminum additions on the coating vale and corrosion resistance of Cr-Fe diffusiou coalings on a mild steel substvate has been studied. Aluminum additions up to 2 wt pct increase the chromium penetration rate while further additions retard it. The apparent cor$lict between these data and metallogyapkic ineasurements, which show a continuially increasing coaling thickness with aluminum addition, is discrissed. Compavisorz of corrosion resistance on the basis of equal thickness of tlre entire coating measured mnetal- ALTHOUGH ferrous metal articles are cheap and widely used, they are often quickly degraded by corrosion. To prevent or slow down the corrosion process, lographically is misleading; equal thickness of the cor-rosion-resistant portion of the coating is a bette.v basis of conzpavison. Inter difision coefFicients for Cr-Al-Fe coatings of different aluminum content have been detevmined and found to dary logarithmically when plotted againnst chromium concentvation. A general method of calculating diffusion profiles for different lrealment limes and surfuce coucentralions IS described. many types of coating are applied to steel.' Among these are diffusion coatings, formed by high-temperature diffusion of selected elements into the surface, which then becomes the coating Diffusion coatings are metallurgically bonded to the substrate and show a continuously varying concentration gradient from surface to substrate. Generally, these coatings have the advantage of adhering to the substrate upon deformation of the composite. Moreover, when chromium is one of the diffusion elements, a mild steel substrate

Jan 1, 1968

By W. L. Dennen, V. H. Wilson

THIS paper is a description of the opera¬tion and results of a Humphreys Spiral Silt Cleaning Plant at the Powderly Colliery of The Hudson Coal Co. during the first nine months of operation and follows a pre¬liminary description given at the Anthracite Institute in May, 1947, in a paper titled "Preparation of Anthracite Sift for Boiler Fuel in a Humphreys Spiral Test Plant" by H. H. Otto, V. H. Wilson and W. L. Dennen. This plant is considered a full size operating test plant and, like all new plants, numerous minor changes in the methods of operation have been made from time to time to secure the results desired. Views of the silt preparation plant and of the screening house are given in Fig 1 and 2. This plant consists of 48 spirals in 8 batteries of 6 spirals each, 36 of which were to be operated as primary spirals and the remaining 12 as secondary spirals. A brief description of the plant and its operation follows. The only material cleaned at the plant during 1947 was that carried in the underflow from the Thickener which handles the Breaker waste water. This underflow, amounting to approximately 2000 gpm of water and containing 12.6 pct of solids, is pumped .to vibrating screens where the plus 316-in. material is removed. (Fig 3). This oversize material drops into a pocket from which it is trucked to the run-of-mine

Jan 1, 1948

The income of the Institute is derived mainly from dues, advertising in MINING AND METALLURGY and sale of publications. These sources fortunately are supplemented by the interest from invested funds now amounting to over $500,000, a considerable portion constituting endowments for special purposes. Aside from the medal funds the principal endowments are the James Douglas Fund for support of the Library, the Charles Hayden Memorial Fund, designated to further the education of Student Associates, the Rocky Mountain Fund, and the Seeley W. Mudd Memorial Fund. The income from the two last named is available for the support of research and a variety of other purposes. It is allocated by the Board of Directors upon recommendation of standing committees in each case. An active effort is being made to increase the endowment funds of the Institute through a standing, committee, of which H. T. Hamilton is chairman, and of which the other members are: W. H. Aldridge, George D. Barron, Cleveland E. Dodge, Henry Krumb and J. V. W. Reynders. This committee feels that there exists a tremendous opportunity for the Institute to be of ever-growing service to the public, to the mineral industries, and to the profession. It welcomes suggestions as to names of men of means who are vitally interested in the mineral industries, and to whom the opportunity to make a contribution or bequest might appeal favorably if presented in the proper light by the committee.

Jan 1, 1940

By K. C. Li

ARSENIC and antimony are always grouped together by chemists, since they are both members of group V of the periodic table of elements and exhibit a general similarity in the formation of compounds. Metallurgists generally think of them as less closely related because they do not have similar uses. In metallurgical operations, especially lead and copper smelting, arsenic tends to go off as a vapor phase and collect as fume in the flues, while antimony tends to remain with the bullion. Broadly speaking, the frequency of occurrence, practical utility and the effects on associated metals of arsenic and antimony are such that the metallurgist is inclined to think of arsenic as a troublesome impurity in ores, but of antimony as a valuable constituent that is recovered either as a byproduct or through the metallurgical treatment of antimony ores. Estimating the world production of arsenic as about 40,000 tons annually, probably not more than about 200 tons yearly is produced and used in metallic form, whereas one half of the approximately 40,000 tons of antimony produced annually is metallic. ARSENIC The modern uses of arsenic differ little from ancient ones. Though it has been known from early times, its poisonous quality is almost the only one that yet finds extensive use. The shift in the past century from its utilization in poisoning people to the poisoning of insects, beginning in 1860, has not only led to a considerable increase in

Jan 1, 1953

"Located on Missouri River 16 miles N. E. from Helena, 67 miles from Butte and 18 miles below Canyon Ferry. River drainage area 16,000 sq. miles.DAM: Built in 1907; rebuilt of concrete in 1911. Maximum height 129.3 ft., length over all 720 ft.; elevation of crest 3621; elevation of bridge 3640; normal head 60'; normal tail water elevation 3568.5.SPILLWAY: Length over all 491 ft.; clear opening in 24 sections; 445' flashboards, 14 high to elevation 3635, which is 3.5' above Canyon Ferry normal tail . water elevation.PENSTOCKS: 5 of steel, 12 ft. diam., about 75 ft. long from canal to main turbines, and 3 40-inch diam. from canal to exciters.WHEELS: 5 main pairs, horizontal, center discharge, 48-inch bronze turbines, 225 rev., 4,000 h-p. at 60 ft. head, made by S. Morgan Smith Co., direct coupled to generators, and--3 single, horizontal, 25-inch units, direct coupled to exciters.GENERATORS: 5 W. E. & M. Co. water wheel type, revolving field, 2,800 k-w., 2,400 v., 225 r. p. m., 3 phase, 60 cycle alternators.OPERATION: The plant has a larger water storage than Canyon Ferry and can also use stored water from Canyon Ferry storage. Separate transmission lines 13 miles long connect to lines from Canyon Ferry to Butte, and the Plant operates in parallel with the Canyon Ferry plant."

Jan 1, 1913