Search Documents

By G. W. Healy, W. Craft, D. C. Hilty

By means of a theoretical extension of the Cr-C temperature relation in molten chromium steels to low chromium contents and by a correlation of the ratios of chromium to iron in the slag and metal, a method has been developed for estimating the amount of metallic oxidation during the oxidizing period of a chromium steel heat. Application of this method has indicated that due to temperature limitations metallic oxidation may be excessive for very low carbon steels charged with more than a small amount of chromium. IN the melting and refining of chromium steels the oxidation of carbon to a low level is accompanied by the oxidation of chromium and iron in considerable amounts. For the subsequent recovery of chromium and associated iron from the slag, the amounts of metal oxidized must be known for efficient reduction and control of composition. Further, in order to arrive at an accurate understanding of the process, so that chromium-bearing scrap can be used effectively, information is required on the relation between composition of the charge and weight of metal oxidized to reach the desired carbon content. Crafts and Rassbach1 recently developed an empirical relation between chromium, iron, and manganese oxidized per ton of steel charged, and final carbon content and temperature. This relation did not show any dependence on amount of chromium charged. However, it was felt that such a dependence might be present, so a further analysis of the data was undertaken. Cr-C Relation at Low Chromium Levels Crafts and Rassbach's results were based on temperatures estimated from the Cr-C relation previously established experimentally by Hilty,2 and on a single temperature observation (immersion thermocouple) on a heat made at low temperature from a charge of carbon steel scrap containing only a small amount of residual chromium. The temperatures estimated from the Cr-C relation were for heats charged with chromium-bearing scrap and which contained substantial amounts of chromium (2 to 10 pct) at the end of the oxidizing period. No data, other than that from the low temperature heat just mentioned, were available for the low and intermediate chromium ranges. In order to extend the range in which temperature may be estimated, the Cr-C relation requires further consideration. The Cr-C relation, expressed as suggests that carbon is zero at zero chromium in the bath. This is obviously absurd, because as chromium approaches zero the carbon content must approach the limit established by the Fe-C-O equilibrium. It is evident, therefore, that the Cr-C relation as defined by Eq. 1 is not valid below some minimum chromium content that may vary with temperature. On the other hand, it is probable that any such limiting chromium content is less than 4 pct at 3200°F, since the experimental data from which the Cr-C relation was derived included several observations at that level with no deviation. In any event, it is apparent that further evaluation of the results presented by Crafts and Rassbach is dependent upon a means for estimating the Cr-C temperature relation in the low chromium region. From the observations of Chen and Chipman9 and thermodynamic data given in Basic Open Hearth Steelmaking,4 the following relation can be calculated for melts containing small amounts of chromium and carbon assuming a carbon monoxide pressure of 1 atm: % Cr -21,250 K' = (%C)2; logK1 == —t— +13.88 [2] Moreover, by plotting Eq. 2 for any given temperature on cartesian coordinates, it can be extrapolated graphically to the limiting carbon content at zero chromium for the specified temperature without serious complications. By means of Eq. 2 and its extrapolation, the Cr-C temperature relations originally established experi-

Jan 1, 1954

By R. Floyd Farris

A method is presented for determining minimum waiting-on-cement time, which takes into account the differences that exist between types and brands of cements and such individual well conditions as depth, temperature, and pressure. The basis for the method was determined by laboratory tests. Being a laboratory development, several steps were required to prove its merit. The first step consisted of laboratory tests designed to determine the minimum cement strength required in wells. Basis was found for setting a minimum value of 8 Ib. per sq. in. tensile strength. Next, it was shown by laboratory tests that the time to 8 Ib. per sq. in. tensile strength may be expressed as a function of consistometer stirring time to loo "poises," the approximate relation being "the time to 8 Ib. per sq. in. tensile strength equals the time to I00 'poises' times three." Next, it was shown that the time of maximum temperature development in cement slurries, due to heat of hydration, is also related to consistometer stirring time to loo poises, but only by a factor of approximately two. It was shown also that the shut-in casing pressure will build up after cement is placed and register a maximum pressure at approximately the same time the slurry down the hole attains maximum temperature. From this and the relationships listed above, the general rule was established that minimum waiting-on-cement time (time to 8 Ib. per sq. in.) after casing cement jobs in any well is equal to the time when the shut-in casing pressure reaches a maximum, as measured from the initial mixing of cement, times a factor of 1.5. Cement plugs drilled in the field at the time prescribed by this formula were found to drill "firm to hard," thus confirming the laboratory tests. These tests prove that many of the present regulations for waiting on cement require a longer time than is absolutely necessary. Use of the method herein proposed offers the possibility of a saving of $1200 per well. Introduction The length of time allowed for cement to set after casing is determined either by state-wide rules, field rules, or self-imposed rules written into drilling contracts. In general, the time is dictated by experience and common practice. However, owing to differences in opinion and in experience of the various groups involved, waiting-on-cement time often varies from one area to the next. For example, an operator in an area where no rules exist may drill out of surface pipe at 24 to 36 hr., while another operator in another area may wait 48 hr. or more to comply with state or field rules, although the depth of the well, hole size, type of cement, and other data are identical. An even greater difference in practices will be found by making similar comparisons with respect to oil-string cement jobs. Differences in waiting-on-cement times of 36 to 48 hr. are common. Further complicating the picture is the rather common practice of allowing more waiting time for cement to set at the greater depths than is allowed at the shallow depths. This practice has existed for years in spite of the common knowl-edge1,2,3 that the temperature of the earth at the usual setting depths of surface

Jan 1, 1946

By Charles Y. Clayton

The shank, to give good service, should not upset nor should it cause excessive wear on the various parts of the machine. To fulfill these requirements, the steel must have a certain hardness—that is, resistance to deformation. The hardness is expressed in conventional terms, as Brinell or scleroscope number. Before deciding on the hardness that is proper, several factors should be considered; the most important are: type of drill steel used (whether hollow or solid), length of steel, nature of ground, air pressure, and hardness of hammer or anvil block (usually 600 Brinell). These are not all, but they are the most cogent ones. Without doubt, it would be better to use a shank that is too soft than one that is too hard. Most satisfactory service will be obtained from shanks that are just hard enough to resist any tendency to upset. To express the proper hardness in terms of Brinell numbers would mean a great many tests over a long period of time, or a study of drill steels that are being used successfully in the various districts. To obtain some information along this line, the persons making this investigation requested, a number of companies to send to them drill shanks that had been given the usual treatment at that mine. The results of the hardness tests are given in Table 1. The hardness values given in Table 2 are those of shanks known to have been quenched in water and drawn. These results show that where water quenching and drawing are in vogue the hardness is rarely under 400 Brinell.

Jan 1, 1923

By G. R. Fitterer

NONMETALLIC inclusions in steel have received much attention by metallurgists during the past few years. Many investigators have been emphatic in stating their belief that these impurities are the chief causes of steel failures, while others think that their effects are negligible. One of the main reasons that definite information on the effects of these impurities is lacking is that no reliable method has been developed for the exact determination of the amounts of these different impurities in steel. Some valuable new information has been brought out by a reliable method for nonmetallic inclusions which has been developed at the Pittsburgh Experiment Station of the U. S. Bureau of Mines, in cooperation with the Carnegie Institute of Technology and the Metallurgical Advisory Board. This procedure satisfactorily extracts some of the more common inclusions from steels, thus enabling the investigator to correlate steel failures with inclusion content. Although the data given herein are the first to be published on the subject of the electrolytic extraction method, the interest in the subject is evidenced by the fact that it is already being used by some 20 to 30 steel companies for their various purposes. Some of the comments received from these laboratories indicate that the method is highly satisfactory: the unfavorable comments, when traced to their sources, have been found to be based on some small mistake made in either installation or operation. The chief discrepancy seems to have occurred in attempts to apply the method to the extraction of inclusions from alloy steels. The procedure can be used only for the plain carbon steels and for such low alloy steels as those containing the usual amount of copper (0.2 to 0.3 per cent). Steels containing the carbide-forming alloys such as chromium, tungsten, etc., present far too many difficulties for the accurate determination of inclusions. Luckily, the iron and manganese carbides do not offer any difficulties and no contamination of the oxide-sulfide residue results. It is highly probable that some modification of the following

Jan 1, 1931

By C. M. Wayman, J. F. Breedis

The crystallography of the martensitic transformation in the Fe-30 Ni alloy was reinvestigated. The scatter in the habit Plane as determined from measurements on the mid-rib plane was smaller than reported previously, and the orientation relationship was determined from a martensite plate having known direction cosines. From agreement with crystallographic theory and from observations of the morphnlogy of the martensite plates, it is suggested that the mid-rib plane represents the starting region of the transformation. THE crystallography of the martensitic transformation in the iron-nickel system has been the subject of many investigations.&apos;-7 However, for iron alloys containing approximately 30 wt pct Ni, a wide scatter in the reported habit planes exists. In only one instance has a Laue determination of the orientation relationship been made, but the habit plane of the martensite plate studied was not determined experimentally. Because the most successful thermodynamic and kinetic analyses8 of the martensite transformation have been based on Fe-30 Ni alloys, it was considered desirable to reinvestigate the crystallographic features of the transformation in this alloy. Lieberman9 suggested that the most significant information for use in a theoretical treatment involves the determination of all the crystallographic observables from a single plate of the product phase. This was first done in essence by Greninger and Troiano10 for Fe-22 wt pct Ni-0.8 wt pct C, and is the method followed in this investigation. Some theoretical approaches11-13 in describing the martensitic transformation consider the overall transformation distortion to be comprised of a Bain distortion, or lattice deformation (PI, which produces the structure change, and a lattice invariant deformation (G), such as twinning, which together leave the interface or habit plane un-distorted. The incorporation of a rigid body rotation (R) results in a transformation distortion (E) such that the interface plane is left both undistorted and unrotated. In matrix notation, E = RPG where the lattice invariant deformation has "taken place" in the austenite. Bowles and Mackenzie14-16 in formulating a theoretical approach proposed an adjustable scaler quantity, denoted as 6, which represents a uniform dilation in the interface plane. This dilation acts to adjust the lattice spacings of the parent and product structures at the plane of contact. Using the dilation parameter as a variable, these authors were able to account for a continuous variation of habit planes in steels along a curve in the stereogram between {225}A and {259}A. she invariant line strain14 of the transformation is 6 RP, and the corresponding transformation distortion is E/6.) With the dilation parameter known, the invariant line is computed as the triple coincidence of the habit plane, the shear plane of the lattice invariant deformation, and the initial Bain cone.14 The contraction axis for the Bain distortion can be taken9&apos;17 as [010]A, and the correct permutation of the habit plane indices used. Kelly and Nutting 18 have established the shear plane (of twinning) in the tetragonal martensite of Fe-22 Ni-0.8C to be {112)M by means of transmission electron microscopy. The reasonable shear system is then {112}M which is equivalent to {011}A <01l>A. The as-

Jan 1, 1962

By F. Keller, R. H. Brown

Because of the extensive use of Alclad 24s alloy sheet in aircraft construction, there is much interest in the metallurgical changes caused by heat-treatment of this product.1, 2 One of these changes is the result of the diffusion of soluble elements from the core into the coating during treatment. This paper deals with the thermal treatments that may influence diffusion and with the practical effects of diffusion on the serviceability of the product. As is well known, Alclad 24s-T sheet has a core of high-strength alloy combined with surface layers of relatively pure aluminum. The microstructure of a cross section of this product is shown by Fig. I. Not only does the relatively high-purity coating have a high resistance to corrosion, and hence serves as a mechanical barrier between the core metal and the corroding environment, but in addition this coating exerts electrochemical protection over areas where the core may be exposed, such as cut edges. In addition, the coating affords electrochemical protection to projecting heads of A17s-T, 17s-T and 24s-T rivets, or attached members made from these alloys. Under some conditions of heat-treatment, however, diffusion of copper into the coating will alter the electrochemical relationship between the coating and the core to the extent that only partial protection will be obtained under some corrosive conditions. The reason for the electrochemical protection lies in the fact that the coating layers of pure aluminum are anodic to the alloy core. The addition of copper to aluminum produces alloys in which the potential is lower than that of the pure metal. Moreover, as the amount of copper in solid solution in 24s alloy is increased, the potential of the alloy becomes more cathodic. When heat-treated at 920°F. and quenched in cold water, 24s-T is about 0.16 volt cathodic to pure aluminum. However, copper will diffuse from the core into the coating, and if it reaches the surface the potential will be altered in a cathodic direction. Thus the potential difference between the core and coating may be less than 0.16 volt, depending uponIthe thickness of the coating, and the time and temperature of heat-treatment. Of the methods available for determining the extent of diffusion of copper from the core into the coating of Alclad 24s-T, two are generally used; namely, the metallo-graphic and the solution potential methods.3 Metallographic Methods Metallographic methods will reveal the progress of diffusion of copper into the coating. For instance, the diffusion zone in the coating intermediate between the coating surface and the core is shown in Fig. I. This photomicrograph is of a polished and etched cross section of 0.040-in. Alclad 24s-T sheet. Diffusion proceeds into the coating more rapidly along the grain boundaries than through the body of the grains. Consequently, the diffusion zone is not of uniform width

Jan 1, 1944

By A. A. Burr, D. G. Ebeling

The effects of casting texture, grain orientation and grain size upon the performance of Alnico permanent magnets is described. Single-crystal specimens were produced by special sintering and grain coarsening techniques to study the effect of crystal orientation. In addition to texture and orientation effects, an analysis of the results indicates that the permanent magnet performance is impaired by a refinement of the grain size. AN excellent historical review of the development of Alnico permanent magnets has been prepared by Bozorth.1 The desirable permanent magnet characteristics of Fe-Ni-A1 alloys were discovered in 1932 by Mishima.2,3 The work of Ruder&apos; showed that the alloys were age-hardenable, and Betteridge5 defined the best composition and heat treatment for the magnetically isotropic alloy known as "Alnico 3." Horsburgh and Tetley0 increased the energy product by the addition of cobalt and copper, "Alnico 2," and Oliver and Sheddon7 demonstrated that cooling in a magnetic field improved the residual induction of this alloy. Jonas8,9 then disclosed the great practical benefits of heat treating an alloy of higher cobalt content in a magnetic field and the resulting alloy, "Alnico 5," has become the standard of the industry. This paper describes the fundamental aspects of a procedure which can be used to further improve the properties of these anisotropic permanent magnet alloys. A study of the casting techniques used in the production of anisotropic Alnico permanent magnets indicated that the magnetic quality was affected by the as-cast macrostructure. Improved performance was observed in magnets containing a high percentage of columnar grains whose long axes were parallel to the magnetic axis of the casting. McCaig10 studied the effect of such columnar grain structures upon the magnetostriction characteristics of similar alloys, however no data was presented showing the effects on other magnetic properties. The following paragraphs describe two experiments which were conducted to determine the effect of various grain orientations upon the energy product. Special composite molds were prepared of highly conductive and highly refractive components to remove the heat of solidification from the casting in a controlled manner. Representative macrostructures produced by these techniques are shown in Fig. 1, along with the relative volumes of favorably oriented columnar grains. The alloy, Alnico 5, has the highest permanent magnet performance of any commercial magnet material. It has the nominal weight composition of 8 pct Al, 14 pct Ni, 24 pct Co, 3 pct Cu, and 51 pct Fe. A heat of this material was cast into molds producing the type A and B grain structures shown in Fig. 1 and pairs of the resulting magnets were placed in heat-treating boats so as to eliminate any biasing effects of boat position. After a standard heat treatment the type A magnets, with 16 pct of the volume composed of favorably aligned grains, had a maximum energy value of 3,940,000 gauss-oersteds, while the type B magnets with 73 pct aligned grains averaged 5,090,000. This large im-

Jan 1, 1954

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By Gregoire Gutzeit

THE development reported in this paper was begun by the author a number of years ago, while he was a lecturer on complex chemistry and metallurgy at the University of Geneva, Switzerland, and in charge of that institution&apos;s research laboratory. Completion of the development and reduction to practice did not occur until last year at the Westport mill, laboratories and testing plant of the Dorr Company, where this method is now in general use for identifying and localizing the mineral constituents of both metallic and nonmetallic ores. It has proved to be a practical tool of the metallurgical staff at the Westport mill, devising unusual milling flowsheets for complex and refractory ore bodies. In a number of instances the findings have been successfully used as fundamental factors in the design and specification of complete metallurgical plants. Seven examples of the use of this method in solving practical milling problems are included in this paper. GENERAL OUTLINE The microscopic study of an ore, at first only of scientific interest, has proved extremely useful both in practical geology and in ore dressing. The binocular magnifying lenses for rough observation of the products of an ore-dressing plant have been in use for a long time; but only within the last few years has a systematic microscopical examination of ore samples become a normal tool of any research laboratory dealing with ore-dressing problems. Such an investigation avoids considerable loss of time as well as empirical trials and useless experimentation. It will generally indicate the correct grinding and often will suggest the proper method of treatment. The petrographic determination of transparent minerals in thin sections, or even in grains, has been perfected, and very accurate methods have been devised to meet any requirement, such as Feodorof&apos;s rotating stage on the petrographic microscope. Almost all transparent minerals can be positively identified by their optical properties; i.e., isotropism, anisotropism, color, pleochroism, refractory index, cleavage, crystal form, birefringence, and others. The identification of opaque minerals is a much more difficult problem and can be done only by using polished specimens. Unfortunately, most of the valuable metallic ores, and even some of the nonmetallic ones, are not transparent; therefore it has been necessary to develop a special technique for the determination of these minerals. Some optical properties-for instance, isotropism, anisotropism, color, cleavage, reflecting power-are often adequate in roughly classifying the mineral. Only "reflecting power" is a measurable value, provided special photometric equipment (ocular photometer or Orcel&apos;s photoelectric cell) is available. The other optical properties mentioned are more or less relative,

Jan 1, 1942

By L. W. Legerwood

During the past three decades, the oil industry has expended increasing eflorts seeking improved drilling tools or systems to reduce drilling costs. The total cost of these efforts is unknown, but it certainly amounts 10 tens of millions of dollars. Most of the "new" system that past and present investigators have sought to develop actually are old public information. In seeking to implement new-systern concepts, investigators have tested the following: impact at frequencies ranging from 6 to 300 cycles per second; electrical, mechanical and hydraulic meam of actuating percussors; bit rotary speeds up to 2,000 rpm; electric and hydraulic bottom-hole means of rotating bits; bottom-hole machines with power outputs up to 400 hp; shock waves; explosives; high-velocity pellets; flame; arc; grinding wheels; abrasive jets; erosion by high-velocity gases; chemical attack; electric current; magnetic waves; retractable rock bits; reelable drill pipe; continuous coring with reverse circulation; and automation of drilling rigs. Table I shows how these investigations are grouped for discussion purposes in this paper. In spite of these efforts to discover new and improved systems, rotary drilling main;aim its economic leadership. Undoubtedly, rotary drilling costs will continue to be reduced by rigid application of the best available technology and by development of new rotary technology. In view of the extensive past development programs, however, significant long-range improvement appears to be a research, not a development problem. Research must postulate and prove theories and principles governing variour subsurface rock-failure processes pertinent to both rotary and new systems. Ah, research must produce physical and engineering data relative to these processes. When such information is available, earth boring will graduate from an art to a science. Major improvements in rotary drilling can then be expected, and the systematic evolution of an improved drilling method can be initiated—with a strong probability for success. Development of drilling methods other than rotary drilling has been one approach investigated by the industry as a means for reducing drilling costs. Major cost-reduction efforts, however, have been centered on engineering development work aimed at incremental improvements in rotary drilling. A relatively minor effort has been expended to establish basic physical principles and engineering data pertaining to the earth-boring process which can serve as a foundation for the development of cost-cutting drilling hardware. Current oil-industry economic trends have added impetus to the need for effective programs to reduce drilling costs. However, areas for expanded future efforts should be selected only after careful study of past investigations. It is the purpose of this paper to review past and Dresent industry efforts to develop new drilling tools or systems and to suggest areas where additional science is needed. Past reviews of drilling methods have been limited to a few processes prominent at the time the reviews were made. This paper seeks to present a concise, well organized review of all methods that have received actual development or test work. The preparation of a paper seeking to review all past developments is fraught with many difficulties, not the least of which are errors in or obsolesence of printed matter used as source material and the lack of data on industry developments which have not been published. Since de-

By Alan Arias

On grinding in pure water, zirconium, tantalum, iron, and stainless-steel powders were extensively comminuted and simultaneously oxidized with hydrogen release, whereas nickel, copper, and silver powders did not react with water and their particle sizes increased. On grinding nickel, copper, and silver in water pressurized with oxygen, nickel and copper became extensively comminuted and were oxidized, whereas silver did not react with oxygen and its particle size increased. From these results and other considerations , it is hypothesized that for extensive comminution of ductile metals and alloys to occur on grinding they must react with the grinding media. UlTRAFINE metal and alloy powders are finding an ever-growing number of applications in metallurgy and in other fields.&apos; Of particular interest are ultrafine metal and alloy powders suitable for dispersion strengthening.2&apos;9 Various research programs on dispersion strengthening are being carried out and in some of these programs the ball-milling method is being used to produce dispersion-strengthened materials. This method usually involves the simultaneous grinding of metal or alloy and a dispersoid followed by consolidation of the resulting powder mixture. To obtain the ultrafine powders required for dispersion strengthening,&apos; grinding is carried out in many liquids, including aqueous and nonaqueous media, with or without grinding aids.4&apos;5 Nonaqueous liquids usually contain water as an impurity and some grinding aids may contain water of hydration.5 The water present may affect the grinding process. The writer has shown5 that. on ball milling chromium in water, the chromium is oxidized and hydrogen is released. It was surmised that the same reaction may occur on ball milling other metals and alloys in waterbearing liquids. Therefore, the investigation of ball milling in water was extended to metals and alloys other than chromium. In the course of the investigation, however, it became apparent that the data-to-gether with the results from a few additional experi-ments—could be used to postulate a comminution mechanism for ductile metals and alloys. A well-known comminution theory is that of smekal.7 According to this theory, comminution is possible because of the weakening effects of surface cracks and other imperfections in materials. This theory imposes a lower limit of about 1 µm for the ground particles. The beneficial effects of liquids and additives on the rate of grinding are well known.8 Mechanisms by which liquids and additives may aid in grinding were reviewed by Rose and Sullivan.&apos; One aspect of these effects is based on Rehbinder&apos;s theory of crack propagation in materials under stress.9 According to Reh-binder&apos;s theory, liquids or additives may promote the spread of cracks in stressed materials by lowering the surface tension at the crack tip. Rose and Sullivan surmise that the same mechanism may be operative during grinding, thereby facilitating comminution of the particles. In addition, Rose and Sullivan reviewed how additives may act as dispersants as a result of their being adsorbed on the surface of the particles being ground. This concept has been suggested by Quatinetz, Schafer, and smea15 to explain from their experiments the major role of additives that enabled them to grind metal down to 0.1 µm. Discussions of other comminution theories and additional sources of material on the subject will be found in Ref. 10. None of these previous suggestions and theories, however, can account for all phenomena encountered during ball milling of metals to submicron size in this and in a previous investigation by the author.6 The objectives of this investigation were to determine the behavior of metal powders during ball milling either in pure water or in oxygenated water and to gain an insight into the grinding mechanism. Zirconium, tantalum, iron, nickel, copper, and silver powders were ball-milled in pure water. These metals were selected because their oxides cover a wide range of free energies of formation. For comparison purposes, an alloy-type 430 stainless steel-was also ball-milled in pure water. The pressure of the hydrogen released during ball milling was monitored in order to determine the oxygen that combined with the metal or alloy. In order to obtain more information on the nature of the grinding process, nickel, copper, and silver powders were also ball-milled in oxygenated water (water pressurized with oxygen). The oxygen that reacted with the powders was determined from the pressure decrease in the mills. The powders resulting from ball milling in pure water and in oxygenated water were subjected to surface area, optical microscopy, and X-ray diffraction analyses. With these data, the oxygen calculated to be combined with the metals during ball milling, and comparison of the free energies of formation of the oxides of the milled powders with that of water, a comminution mechanism was postulated. MATERIALS, EQUIPMENT, AND PROCEDURES The materials used in this investigation were powdered metals, deaerated distilled water, high-purity helium, and commercial grade (99.5 pct purity) oxygen. The powdered metals used were zirconium, tantalum, iron, nickel, copper, and silver. A 16 pct Cr, ferritic stainless steel, type 430, was also used. The purities (or nominal compositions) and the surface areas of these metals and the alloy are given in Table I.

Jan 1, 1970

By J. Nutting, J. W. Cahn

WITH the development of thin film techniques for the direct examination of metals in the electron microscope some new problems in quantitative metallography have become apparent. In order to obtain certain contrast effects in the electron optical image when examining thin films from alloys containing dispersed phases, it is essential to use films of a thickness at least two or three times greater than that of the mean particle diameter of the dispersed phase. From micrographs of such specimens it may be desired to obtain the volume fraction of the dispersed phase and the number of particles of the phase in a unit volume of the matrix. Under these conditions the particles sectioned by

Jan 1, 1960

By M. A. Mahtab, J. D. Dixon

The results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block- caving method are presented. The two-dimensional finite-element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1977

By H. M. Varner

Under sponsorship of the US Bureau of Mines and the Department of Energy, a new type of rotary rock drill was developed by The Bendix Corp. Originally developed for the production of holes for the installation of longer than seam height roof bolts, the flexible drill is a useful tool for many drilling applications. It allows hands-off or remote production of holes for increased drilling speed and greater operator safety in any strata suitable for rotary drilling. This paper discusses various applications and experience for the flexible drill system in coal, metal/nonmetal mining, and for civil engineering uses. Manual, remote control, and automatic roof bolter modules are also discussed.

Jan 1, 1984

By Henry G. Granger

A residence of 14 Sears in the Republic of Colombia, spent . in almost continuous traveling and prospecting-trips, has given me an intimate knowledge of the resources of that wonderful country. The man who best knows Colombia is unquestionably General Rafael Reyes, President of the Republic for the past three years, and with seven years more to serve in his present term. Such is the strength of his personality and the wisdom of his policies that his term of office will no doubt endure as long as he is milling to serve. The vastly improved economic situation and the brilliant outlook for Colombia are so directly due to the influence of President Reyes that a few lines concerning him will not be amiss, if they serve towards a better understanding of his personality. Born of a distinguished ancestry in the mountain~ of Boyaca, he is now 57 years old, just the age of his friend Porfirio Diaz when he began the work which has placed Mexico in the rank of great modern nations. It was Reyes who came to Washington to protest against the action of the government of the United States of America in

Jan 1, 1909

By Harmel A. Dawson, Robert A. Wilson

First the basic steps to determine the values present and the minerals involved which are the basis for the metallurgical testing are presented in this paper. Next, choosing the process or processes indicated for treating an ore are discussed. This is followed by the test procedures used, the results of which will indicate amenability to treatment. These test procedures have been developed, used and proven effective in laboratory evaluations relative to plant processing. Special, uncommon processing is beyond the scope of the paper. Evalutation of test results and incorporation into the preliminary and final flow sheet for plant design are discussed. The value of a flow sheet, with material and water balances, to plant design is shown.

Jan 1, 1978

By A. W. Fahrenwald

THE function of the classifier in modern fine-grinding practice is to remove a finished product from the grinding-mill discharge, leaving material that needs further comminution. The classifier, therefore, makes two products: (1) "finished" product, which overflows the rim of the classifier tank, sometimes referred to as "slimes" or as "classifier overflow," and (2) "unfinished" product, which settles to the sloping bottom of the classifier tank and is removed by dragging or raking. This product is generally referred tows "sands" or "oversize." One of the outstanding features of the closed-circuit classifier is its ability automatically to return the unfinished product of the ball-mill discharge to the feed end or scoop box of the ball mill. This is a distinct advantage because it avoids dilution of the ball-mill feed, and, furthermore, the particular method of removing the settled sand, by raking it up the inclined bottom of the classifier, gives a classifier discharge containing a minimum of water. This leads to maximum classifier efficiency, in this type of classifier, because the maximum volume of water is displaced upward by the settling sands. The closed-circuit classifier is required to deliver a finished pulp of closely specified density requirements, therefore added hydraulic water generally is not permitted.

Jan 1, 1930

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

By S. K. Asunmaa, W. D. English, N. A. Tiner, W. A. Cannon

This paper discusses the reaction of metal surfaces with fluorine. Fluorination reactions result in the formation of metal fluoride films which are "passive" toward further reaction of the metal with fluorine. These films are very adherent, and do not easily detach from the substrate metal by mechanical flexing or thermal shock. Exposure of passive films to a humid atmosphere produces hydrated metal fluorides which cause secondary fluorination reactions upon reexpo-sure of the metal surface to fluorine. The surface films formed range from 10 to 30A in thickness and they pow at the expense of surface oxide films. The apparent film formation is completed rapidly in 15 to 30 min on stainless steel and nickel surfaces. On copper and on Monel surfaces, the film at first grows rapidly, then increases slowly over an extended period of time. Passive films are formed at all fluorine pressures in the range from 0.1 to 1.4 atm at room temperature. ALL metals react when exposed to fluorine. These reactions generally produce surface films which consist of metal fluorides. The rate of reaction is largely determined by the extent to which these films are protective. Although there is an extensive literature concerning reactions of oxygen with metals, there are very few investigations reported concerning fluorine-metal reactions. Brown, Crabtree, and ~uncan&apos; investigated the kinetics of the reaction of gaseous fluorine with copper metal which had been freshly reduced in hydrogen. The reaction rate was independent of pressure over the range from 6 to 60 torr. A logarithmic rate law was obeyed in the temperature range from 25" to 300" ~. There was some deviation at higher temperatures which could have been the onset of a parabolic law. The calculated film thicknesses ranged from about two molecular layers, 10A, for 5 hr exposure at room temperature to thirty-five molecular layers for 5 hr exposure at 200" . The authors concluded that no single mechanism could explain all the observations. O7Donnell and spatkowski2 studied the reaction of fluorine with copper at 450°C at pressures from lo to 133 torr. The reaction was found to be pressure -dependent and followed a logarithmic rate law. It was not entirely diffusion-controlled, and fluorine was thought to be the migrating species in the reaction. Miscellaneous metal-fluorine reactions were investigated by Haendler et ~1.~ Reaction products were identified but no rate data were determined. Air Prod- ucts and Chemicals, Inc., have conducted an investigation of reactions between fluorine and various metal powders at room temperature and 85° C. Fluoride film thickness as a function of time of exposure was reported on the assumption that the reaction takes place between fluorine and metal to form the normal metal fluoride. Surface areas of the powders were only estimated so the relative film thicknesses may not be exact. The data showed reaction rates which were generally logarithmic in character, the rate of film growth virtually ceasing after a few hours exposure time for some alloy powders. The effect of moisture on fluoride films was also investigated by measuring additional reaction with fluorine after exposure of passivated powders to atmosperic moisture. The fluorination of iron was studied by 0&apos;~onnell~ at temperatures from 225" to 525" ~ and at pressures ranging from 20 to 200 torr. In all ranges, the reaction followed a logarithmic rate law and was dependent on the square root of the gas pressure. The author concluded that fluorine gas passes through pores in the film. As the film grows, the blocking of pores leads to a rapid decrease in reaction rate; hence a logarithmic rate law is observed. Jarry, Fischer, and Gunther&apos; investigated the mechanism of the reaction of fluorine with nickel at about 600" to 700°C. On the basis of the metallographic examination of fluoride scales growing on the nickel and from separate radioautographic data, it was claimed that fluorine is the migrating species in the reaction. This is in sharp contrast to the growth of oxide films on nickel where it has been shown that nickel ions migrate through the scale to the gas-solid interface to react with oxygen. Few investigations have been reported of the reaction of fluorine with metal oxides. Such investigations should be of great significance for a better understanding of passivation in view of the ubiquitous oxide films on technical alloys. Haendler et al.3 studied the reaction of fluorine with oxides of copper, tin, titanium, zirconium, and vanadium. Copper (I) oxide reacted as follows in the temperature range 150" to 300"~: temperature above 300" ~ was required for the CuO to react to form additional copper fluoride. Ritter and smith7 also investigated the reaction of fluorine with copper (11) oxide. An oxide powder comprised of spherical particles with a fairly high surface area was reacted with fluorine, starting at room temperature and increasing to 100° C over a period of 3 or 4 hr. The initial reaction was slow until the fluoride film thickness reached about to or 15R at which time the reaction rate accelerated, then decreased again. Most of the kinetic data was obtained during this final phase of reaction. The authors conclude that the film grows slowly at first until the stresses developed in the distorted lattice are sufficient to rupture the initial

Jan 1, 1969

By F. Weinberg

Lead single crystals have been deformed in tension over the temperature range of 4.2°K to the melting point. Changes in flow stress resulting from temperature cycling and strain rate cycling have been measured as a function of temperature for crystals of different orientations and purity. It was found that the flow stress ratio, after correcting for the temperature dependence of the shear modulus, decreased progressively with temperature above approximately 0.5Tm. The activation energy calculated from the high-temperature portion of the curve was found to be markedly higher than that of self-diffusion. For single glide crystals, the corrected flow stress showed an increase above 0.5 Tm before decreasitzg with temperature. This increase is attributed to static recovery occurrittg during temperature cycling. THE temperature dependence of the flow stress, based on temperature cycling and strain rate cycling, has been extensively investigated,&apos; and on the basis of these results dislocation models of the work-hardening process have been proposed. In general, the flow stress is divided into two parts, ts, the short-range interaction term, which is only effective at low temperatures and which decreases with increasing temperature, and TG, the long-range stress term, which is independent of temperature after allowing for the temperature dependence of the shear modulus. The observations demonstrating that tG/µ is independent of temperature were generally carried out at low temperatures to minimize recovery effects. Several investigations have been reported on flow stress measurements at high temperatures2"5 which demonstrate that TG/µ does not remain constant at temperatures above 0.5Tm (where Tm is the melting temperature of the material in OK). Specifically, Hirsch and warrington3 carried out temperature cycling tests at two strain rates on single and polycrystalline aluminum up to 0.8 Tm and on polycrystalline copper. For aluminum they found that the flow stress ratio (the flow stress at temperature T2, divided by the flow stress at the reference temperature T1 in one temperature cycle) dropped progressively with increasing temperature above 0.5Tm. From the slopes of the high-temperature portions of the curves, they determined an activation energy for the deformation process of 1.6 ev (at best) which they considered was in agreement with the activation energy of self-diffusion, 1.35 ev. Calculations of the activation volume demonstrated that the deformation was not controlled by dislocation climb. They proposed a mechanism in which the rate-controlling process at high temperatures was due to the rate of move- ment of vacancies away from jogs, i.e., that of self-diffusion. Results of Lucke and Buhler4 on single crystals of aluminum confirmed this conclusion. They measured the critical resolved shear stress of aluminum over a wide range of temperature and strain rates. They found that the temperature dependence of the critical resolved shear stress was similar to that of the flow stress ratio, as determined by Hirsch and Warrington, and from their data calculated an activation energy for high-temperature deformation of 1.35 ev identical to that of self-diffusion. More recently Gallagher5 has carried out a detailed investigation of the temperature dependence of the flow stress ratio of copper, silver, and gold. In all cases, he found that the flow stress ratio, after adjusting for the shear modulus temperature change, drops at high temperatures. The activation energies he determined were found to be appreciably higher than the activation energy of self-diffusion of the material being considered. The flow stress ratio was found to be dependent on the orientation of the material, and, in addition, an anomalous increase in the flow stress ratio for copper, oriented for single glide, was observed above 0.5Tm. The purpose of the present investigation was to measure the critical resolved shear stress, the flow stress ratio, and the strain rate sensitivity of lead, primarily as a function of temperature. The results should indicate whether, following Lucke and Buhler, the critical resolved shear stress of lead has the same temperature dependence as the flow stress, and, following Hirsch and Warrington, whether the activation energy for high-temperature deformation in lead is the same as that of self-diffusion. Lead deforms as a normal fee material,6&apos;7 is available in high-purity form, can readily be grown as single crystals, and, for this investigation, has the very considerable advantage of having a low melting point, 327°C. The observations of the critical resolved shear stress of lead have been published elsewhere.&apos; EXPERIMENTAL PROCEDURE The experimental procedure was essentially the same as that used in the critical resolved shear stress measurements.&apos; Single crystals of 99.999 pct (59) and 99.9999 pct (69) lead were deformed in tension with a table-model Instron in a silicone oil bath above room temperatures and in a cooled methyl alcohol or liquid-nitrogen bath below room temperatures. The test specimens were rectangular in section, 0.65 by 0.33 cm, and had a 5-cm gage length. The specimens were grown as single crystals with tapered ends, which fitted into matched tapered grips for testing. To obtain the flow stress between two temperatures, specimens were first deformed approximately 1.0 pct at the higher temperature. The test was then stopped, the load relaxed, the oil bath removed without disturbing the specimen, the grips and specimen cooled with a fan and then immersed in liquid nitro-

Jan 1, 1969