Search Documents

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

THE solid nonmetallic inclusions present to some extent in all commercial steels have been variously designated. In early references they were usually called slag inclusions, and this terminology is still retained to some extent. On the premise that all nonmetallic matter produced in a metallurgical process is slag, this can be justified. We have come to think of slag, how- ever, in a more restricted sense, and calling these particles slag inclusions is further objectionable because it fosters the erroneous concept that they are actually incorporated portions of furnace slag. Rarely is this true. The term sonims (coined from solid nonmetallic impurities) was proposed many years ago but never came into common use. In general, the term non- metallic inclusions seems to be satisfactory and adequate. NATURE AND CONSTITUTION OF NONMETALLIC INCLUSIONS From the standpoint of origin, inclusions fall naturally into two classes: (1) those occurring as a result of reactions taking place in the body of molten or solidifying metal and (2) those resulting from mechanical incorporation of refractories or other materials with which molten steel comes in contact. The former are by far the more numerous and have been called indigenous, natural, or native inclusions. The latter are by their very nature sporadic in occurrence and have been called exogenous, accidental, adventitious, or foreign inclusions. They are often referred to as the "slag-stringer" type, though here also the material is not likely to be furnace slag. Substances Found in Inclusions. Nonmetallic inclusions are composed principally of oxides and sulfides but carbides and nitrides sometimes play an important role. In the case of indigenous inclusions the reactions by which these particles are precipitated from molten or solidifying steel may be caused by: (1) oxidation such as may occur during refining or during tapping and teeming, (2) deoxidation by added alloys, (3) change

Jan 1, 1951

By N. M. Langdon

INTRODUCTION. IN considering the magnificent success of Mr. Gayley's Bold experiment of applying dry blast to the blast-furnace, whereby , saving of 20 per cent. of fuel per ton of iron is effected, the question arises whether, still further economy in fuel is possible, and, if so, how it is to be attained? The manner in which the heat generated in the furnace is utilized in the production of pig-iron may be determined, by the method of Bell and Gruner, for any furnace for which the necessary data are obtainable ; and the study of the operation,. tinder various conditions, of a number of furnaces, for which such information has been worked out., should enable us to form some conclusion on the subject. The tables and calculations given below cover the operations of several furnaces reported in our Transactions; also the two furnaces using natural and dry blast in ,Mr. Gayley's experiment, for which the heat-equation has been worked out by Prof. Joseph W. Richards in his admirable discussion' of Mr. Gayley's paper, The Application of Dry Air Blast to the Manufacture of Iron, and, finally, various hypothetical furnaces.. The full list is as follows : A. Isabella furnace, with natural blast. B. Isabella furnace, with dry blast. The data stated. for A and B in Table III. are those given by Professor Richards; except that the heat-units are given for one unit of iron instead of 100 units, and some items of heat supplied, as stated by Richards, have been subdivided, the total being the same as given by Richards. (Columns A and B are introduced in Table III. for comparison with C and D.)

Oct 1, 1909

By . M. Muskat

A THEORETICAL consideration of the mechanics of various water-flooding systems with the viewpoint of comparing their relative merits involves the study of two fundamental properties of such systems. On the one hand, it is important to determine the efficiency of the flood as measured by the percentage of the total area that is swept out by the encroaching water before water actually reaches the output wells. This is really a measure of the regional tendency of the water to "bypass" the oil. On the other hand, the various systems must be compared from the viewpoint of their resistances which determine the rate of fluid production obtainable for given pressures maintained at the water input wells. The first of these questions has been studied and very definite answers have been obtained by means of simple electrolytic models.1 These models showed that, in an ideal system, the percentages of the areas flooded out before water reaches the output wells are about 57 per cent for the direct line-drive flood (the input and output wells being equally spaced and placed in alternate parallel lines), 74 per cent for the regular five-spot network, and 79 per cent for the seven-spot network. With respect to the efficiency of the usual flooding arrangements, they are, therefore, given quite accurately by the above numbers. With regard to the resistances of the flooding networks, electrical conduction models have also been used successfully2 and are well adapted to the problem of determining experimentally the pressure distribution and streamlines, or over-all resistances of specific flooding networks. However, such models do not permit readily a study of the effect of changing dimensions or configuration within a network, since a new model must be made up for each set of dimensions considered.

Jan 1, 1933

By C. Y. Wen, H. O. HOPMAN

l. INTRODUCTION. IN casting a thermal balance of the heat generated and absorbed in a blast-furnace treating lead-, copper- and similar non-ferrous ores, assumptions have always to be made for the values of the heat of formation of slag. ? Considering that the larger part of the charge introduced into the furnace comes out in the form of slag, the significance becomes apparent of a lack of heat-values for the singulo-silicate, which is the type of slags commonly made. The aim of the present investigation is to supply these heat-values as far as possible with the apparatus and the time available. The heats of formation of the ferrous and manganous bi-silicates have been determined by Le Chatelier; 1 those of some silicates other than iron and manganese by Tschernobaeff:2 finally Richards 3 gives a figure for a copper blast-furnace slag of known composition. The existing data and those resulting from the present investigation are assembled in Table VI. II. MATERIALS USED. The materials used in the experiments were silica, ferrous oxide, and calcium carbonate. Silica.-The silica sold in the market as chemically pure usually contains small amounts of magnesia, lime, and alumina, and is therefore not suited for the work. The pure material was obtained from clear quartz crystals from Arkansas, broken in a diamond mortar and ground in an agate mortar to pass 1 Comptes rendus, vol. cxx., p. 623 (1895); vol. cxxii., p. SO (1896). 2 Revue de Métallurgie, vol. ii., p. 729 (1905); Electrochemical and Metallurgical Industry, vol. iv., No. 2, p. 72 (Feb., 1906). 3 Electrochemical and Metallurgical Industry, vol. v., No. 7, p. 266 furls?, 1907;) ; Metallurgical Calculations, vol. iii.,.pp. 474, 475 (1908).

Jul 1, 1910

By K. Leutwyler

The key to realistic casing stress analysis in thermal recovery installations is accurate knowledge of the temperatures involved. Much information leading to prediction of heat losses from tubing string to wellbore has been published. This .same information permits calculation of casing temperature under certain conditions. This paper reviews the basis for most of the published work, the line source solution to the diflusivity equation and examines some of its application criteria in the light of unsteady-state conditions. An alternate finite differences method is presented for correlation, and experimental data pertaining to the heat transfer mechanism in the annulus is reported. In the light of the information presented in the paper, it appears that the assumption of a line source for the tubing-wellbore system is valid even for reasonably short periods of heat flow, .such as "steam soak" operations. The empirically modified equation presented earlier matches computer derived results of the finite differences approach lor periods as short as 50 hours. Previously predicted cas ing temperatures and the associated stress levels are thus verified based on these correlative computations and the reported experimental information. Fall out from the computer output resulting in some studies of the influence of insulating cement properties on casing temperature, and experimentally studied effects of nitrogen placed in the annulus at various pressures., are described. INTRODUCTION Generally speaking, predictions of average casing temperatures have been based on an idealized model involving a centralized tubing string at uniform constant temperature radiating energy towards the casing under steady-state conditions.'. ' Heat is transferred away from the casing to the formation by unsteady-state conduction across thermal barriers consisting of cement and the mud sheath. Heat balances written on the casing permit prediction of instantaneous casing temperatures. During early periods of injection, casing temperature varies appreciably as a function of time; however, for long injection times this variation decays as heat flow from the wellbore to the formation stabilizes, and it becomes virtually negligible as conditions surrounding the wellbore become quasi-steady-state (Fig. 1). Carslaw and Jaeger -escribe a solution to the diffusivity equation for a line source (Fig. 2). A constant supply of heat is introduced into the medium from the line placed into the origin of the x-y coordinate system and parallel to the z-axis. Heat spreads outward in the infinite cylindrical solid and the temperature increase on a line going through point (x, y) parallel to the z-axis at a distance r can be predicted by: The following criterion must be considered: the Carslaw and Jaeger equation is obtained on the basis of a large

Jan 1, 1967

By L. Moyd, P. Moyd

The first commercially available portable gamma ray-neutron beryllium detector, the Rerylometer, was developed by the same group that developed the first practical portable scintillation counter, the Scintillo-meter. This group includes Professor George Brownell, of the Geology Department of the University of Manitoba in winnipeg, and his associates, K. I. Roulston, R. w. Pringle, and R. L. Funt, of the Physics and Engineering Departments of the University of Manitoba. A prototype model was tested in the field by Dr. Brownell during the summer of 1958. Commercial production was undertaken shortly thereafter by Nuclear Enterprises Ltd., of Winnipeg, and a license for manufacture and distribution in the U.S. was granted to Isotopes Specialties Co., of Burbank, California, a division of Nuclear Corporation of America. Early in 1959, we were retained by the 'Mining Division of Minerva Oil Co. to Legin a search throughout North America for minable deposits of beryllium, and to train members of their permanent staff to continue the program. The project included literature sur-veys, interviews with members of various federal, state, and provincial agencies, scanning of our own collection of suites of specimens from various mineral occurrences, and the examination of deposits in the field. The value of a beryllium detector to this program was obvious and arrangements were made to procure one as soon as possible, which resulted in our obtaining and using the first instrument that was produced commercially in the U. S. In addition to the commercially available Berylometer, Mr. William Vaughan and his associates, of the U. S. Geological Survey Geophysics Division, in Denver, have developed and tested several experimental instruments based on the same principles. DETECTOR Principles The detection of beryllium is based on the fact that "hard" gamma rays (1.6 MEV and geater), such as those produced by Antimony convert ordinary beryllium (Be9) to Be8 , with the release of a neutron. The neutrons are counted by a scintillator designed to favor neutron responses while suppressing those of gamma rays. 'The instrument is completely selective for beryllium. No other element can interfere. Instrunlentation The Rerylometer itself, which is cylindrical, is about 8 inches in diameter, 13 inches high, and weighs about 11 pounds. (Figs. 1, 2). The principal components include: 1. A disc of wax to moderate (or "thermalize") neutrons. 2. A boron-enriched polyester-zinc-sulphide fluorescent screen. This material produces strong flashes when struck by thermalized neutrons but only weak flashes from gamma rays. 3. A photomultiplier tube. 4. An electronic circuit, complete with one srnall 71/2-volt dry battery. The photomultiplier tube and electronic circuit convert neutron flashes to electrical impulses, but gamma ray effects are almost

Jan 1, 1961

By G. Thodos, D. E. Matschke

Cansiderable time and effort frequently are expended to establish, with a degree of confidence, the PVT behavior of pure substances. In particular, a great deal of experimental information contributed by a number of investigators is available in the literature. The data of each investigator, although significant in themselves, cannot be used with a high degree of confidence until they are compared with the continuum of information presented by others. Current interest in thermodynamic and transport properties, for not only the gaseous state but the con-densed state as well, requires that PVT infarmation be presented for both regions. The density dependence on temperature and pressure, when presented as a continuum, is of considerable value in itself, especially since the available equations of state fail to properly account for the PVT behavior in the condensed state. For this reason and to incorporate PVT data recently presented in the literature, this investigation was carried out. In their studies concerned with the thermodynamic properties of methane, Matthews and Hurd in 1946 utilized the data of Kvalnes and Gaddy and Olds, Reamer, Sage and Lacey to establish the PVT behavim of methane in the superheated region and the saturated liquid densities of Keyes, Taylor and Smithl in conjunction with the Clapeyron equation to develop the densities for the saturated envelope. Current activity sponsored by API Project No. 44 under the direction of F. D. Rossini has led to a tabular presentation of compressibility factors for gaseous methane in the superheated region.la These values were obtained by using smoothed residuals, developed from experimental data and the Ben edict-Webb-Rubin equation,' to establish internally consistent compressibility factors for the real gas. This approach offers probably the most precise presentation of PVT information for gaseous methane to date. The PVT behavior of methane also can be represented accurately by equations of state such as the Benedict-Webb-Rubin equation or the Martin-Hoa equation.' These equations, although valuable for analytically representing the PVT behavior, lack precision in the compressed-liquid region. The PVT data available in the literature for methane were utilized to obtain reduced densities that are presented in Figs. 1 and 2 as functions of reduced temperature with parameters of reduced pressure. The critical constants utilized for methane are those reported by Kobe and Lynn." These critical values, T, = 191.1°K, PC = 45.8 atm and p, = 0.162 gm/cc, produce a critical compressibility factor, z, = 0.289. The PVT information, as obtained from the literature, in many instances was not presented in an immediately

Organization Place Date 1917 American Electrochemical Society Pittsburgh, Pa. Oct. 3-6 American Institute of Mining Engineers St. Louis, MO. Oct. 8-13 American Gas Institute : Washington, D. C. Oct. 16-19 American Institute of Architects Philadelphia, Pa. _ Dec.. 26-29 American Society of Mechanical Engineers New York City. Dec. 26-29 American Mining. Congress State Chapter Phoenix, Ariz. Dec. 26-29

Jan 10, 1917

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

Map

Jan 1, 1941

By R. F. Nielsen, R. G. Bentsen

Jan 1, 1966

By W. C. Phalen

The production of salt in the United States divides itself at the outset into two distinct classes…

Jan 1, 1915

By David Cole

THE appearance of the Wilfley table in 1897 marked an epoch in the art of concentration of ores. The table has merited and received an almost unprecedented measure of public approval, lasting through its whole patent life. It has been very little improved in itself, or improved upon by competitors. The new machines bidding for popular favor have been of the Wilfley family, but without ability to do markedly better work than the parent m:-chine, or to (to more work except by the use of superimposed decks, the latter having obvious disadvantages. FIG. 1.-The- Butchart RIFFLE System. During the past three years there has been developed at Morenci a new type or arrangement of riffles applicable to the Wilfley type of concentrating table which corrects many of the objectionable features or limitations of the older system and obviates most of the difficulties encountered with it, particularly when handling ores having a low ratio of concentration. The new type is known as the Butchart1 riffle system, and its general arrangement is shown in Figs. 1 and 2.

Jan 2, 1915

By J. F. Wilson

An experimental investigation has been made of gas-driven slug displacements in a system of high gas saturation to evaluate the process for use in a California reservoir. Fluid compositions, temperature, pressure and core permeability duplicated reservoir conditions as closely as possible. The temperature was above the critical of the slug materials. The slug composition required for 100 per cent oil recovery in the linear flow systems was found to agree with that determined from equilibrium phase studies. A qualitative theory for the slug displacement of two-phase systems is proposed and found to be in general agreement with the observed flow behavior. The theory predicts that the length of the reservoir fluid-slug transition Zone will increase with increased initial gas saturation and decrease with increased oil swelling accompanying the composition change from reservoir oil to the critical composition. The precipitation of small amounts of an asphaltic phase during the formation of the transition zone had no adverse effects on the flow behavior of otherwise miscible systems. INTRODUCTION Despite the large number of recent publications relating to oil recovery by miscible displacement, little information is available concerning the behavior of crude oil-natural gas systems at conditions likely to be encountered in field application. The laboratory data reported here were obtained during an investigation of the possibility of using a gas-driven LPG slug in a partially depleted California reservoir. Seven gas-driven slug displacements employing slugs of different compositions and sizes were made in 26- to 27-ft long sandstone cores. The equilibrium phase behavior of the systems was also determined. The features of primary interest in this study are the following. 1. Data were obtained on the displacement of reservoir fluids at reservoir conditions. 2. A high gas saturation existed in the long cores at the start of the displacements. 3. The temperature of the studies was above the critical of the slug materials. 4. A comparison between the flow behavior and equilibrium phase behavior, as illustrated by a pseudo-ternary phase diagram, is afforded for a system of considerable complexity. THEORY Phase Behavior The use of the pseudo-ternary phase diagram to illustrate the phase behavior in miscible displacements has been discussed by Clark, Schultz and Shearin. Sie-vert, Dew and Conley and Arnold, Stone and Luffel' have presented both phase equilibrium and flow data for true ternary systems. For the true ternary, the application of the theory is straight-forward; for a reservoir system represented as a ternary, the theory undoubtedly gives a qualitatively correct picture. One purpose of this investigation was to see if the pseudo-ternary phase diagram could be used to predict with reasonable accuracy the conditions necessary for miscible displacements with actual reservoir systems. MiscIBLE Displacement of Two-Phase System A large number of papers "I3 have treated the miscible displacement of a single-phase fluid from both an experimental and a theoretical viewpoint. However, the normal field application of the process will be in a partially depleted reservoir. Often the state of the system will be such that the mobility of the gas phase is greater

By F. D. Richardson

STAFF: Editor, Gerhard Derge Carnegie lnstitute of Technology Schenley Park Pittsburgh, Pa. 15213 Editorial Assistant, M. A. Redmerski Production Editor, Otto T. Johnson THE METALLURGICAL SOCIETY: Jack H. Scoff, President; Richard C. Cole, Past-President; Harold 0. Emerick, President-Elect; Ralph L. Hennebach, Treasurer; Robert W. Shearman, Secretary; Donald A. Parks, Assistant Secretary; Leslie S. Wilcoxson, Assistant Secretary. PUBLICATIONS COMMITTEE OF THE METALLURGICAL SOCIETY: R. E. Lund, Chairman; T. E. Dancy, H. O. Emerick, P. R. Gouwens, R. E. Grace, J. H. Jackson, H. H. Johnson, A. E. Lee, Jr., R. R. Nosh, R. D. Pehlke, and Paul Queneau. Review and selection of manuscripts is under the supervision of the following Publications Committees: Extroctive Metallurgy Division: R. E. Grace, Choirmon; G. M. Bell, D. W. Bridges, J. M. Cigon, G. W. Heoly, T. A. Henrie, R. D. (Holli-doy, C. E. O'Neill, C. S. Somis, A. W. Schlech-ten, and Charles Shull. Iron and Steel Division: R. D. Pehlke, Choirmon; T. P. Floridis, Arnulf Muon, G. R. St. Pierre, E. T. Turkdogan, L. H.Von Vlock, and J. M. Uys. lnstitute of Metals Division: H. H. Johnson, Jr., Chairman; J. B. Clark, Vice Choirmon; M. R. Achter, G. F. Bolling. J. O. Brittoin, G. P. Conard, II, R. S. Davis, L. A. Girifolco, G. T. Hohn, J. P. Hirth, L. Himmel, G.T.horn, George Krauss, J. D. Livingston, R. D. Manning, H. M. Otte, S. V. Rodcliffe, R. E. Reed-Hill, H. C. Rogers, E. ScaIa, O. Sherby, M. T. Simnad, G. R. Speich, E. A. Steigerwald, R. A. Swolin, W. A. Tiller, W. R. Upthegrove, J. B. Wagner, Jr., Derek Wolton, H. W. Weart, W. W. Webb, and D. Published seven times yearly in February, March, April, June, August, October, and December by the American lnstitute of Mining, Metallurgical, and Petroleum Engineers, Inc., 345 East 47th Street New York, N. Y. 10017. Telephone PLAZA 2 -6800. Subscription $30 per year for non-AtME members m United States and North, South, and Central America; $32, foreign; $7.50 for AlME members Single copies, $6.00, single copier foreign, $6.50. The AiME is not responsible for any statement made or opinion expressed in its publications . . . Copyright 1964 by the American Institute of Mining, Metallurgical, and Petroleum Engineers, Inc. . . . Registered cable address, AiME New York Indexed in Engineering Index, Industrial Arts Index, and Chemical Abstracts. Second dost postaas poid ot New York, N. Y.,ond Ann Arbor, Mich. Volume 230, Number 6.

Jan 1, 1964

By J. E. Campbell, A. W. Wesner, M. Pobereskin

This paper summarizes the results of an investigation sponsored by The Coates Steel Products Company. The objective was to determine the relative effects of certain chemical and physical properties on the wear resistance of grinding balls when grinding cement. In making this study, a number of types of balls were used in both dry and wet grinding in commercial ball mills. The radioactive-tracer technique was used in separating the test balls from the rest of the mill charge and in sorting the different types of halls that were all tested at the same time for each of the grinding operations. PROCESSING OF GRINDING BALLS In order to determine whether the properties of grinding balls, namely, composition, microstructure and hardness, can be related to the rate of wear, the halls used in this study were selected to represent various combinations of these properties. It was recognized that the mechanism of wear was not the same in the wet mill as in the dry mill. Therefore, the types of balls tested in each of the two environments were not necessarily the same. However, all of the types of balls evaluated in the dry mill were tested simultaneously for one time period, while those evaluated in the wet mill were tested simultaneously for three different time periods. All of the test balls were separated from the charge when the mill was dumped. All of the balls were of 0.940-inch diameter when charged, and all but the regular production balls were finish ground to this size to eliminate the decarburized surface layers. The steels and processing methods used, as well as the micro-structures and hardness levels of the balls, are described as follows: Regular production forged SAE 1095 steel balls were used in both the wet and dry mills. They were forged to a nominal diameter of 0.940 inch and quenched in oil from the forging temperature. Each retained a partially decarburized surface layer from the forging bar stock; the maximum depth of this layer was about 0.030 inch and the decarburization was negligible where the ball was sheared from the bar. The hardness at the surface was 40 to 46 Rock-well C in the partially decarburized area and 57 to 62 Rockwell C in the areas not decarburized. The hardened zone extended to a depth of about one-third of the radius. Below the decarburized layer, the hardened zone consisted primarily of hard as-quenched martensite with varying amounts of retained austenite. This structure changed to fine pearlite at a depth of about one-third of the radius. In order to eliminate the effect of the decarburized layer, a set of production balls of SAE 1095 steel was forged to about a 1-inch diameter, quenched in oil from the forging temperature, and ground on ball-bearing grinding equipment to a 0.940-inch diameter to remove the decarburized layer. The balls' hardened zones were similar to those in the previous set. The hardness of the finished surfaces was 52 to 60 Rockwell C. A slight amount of decarburization apparently remained after the removal of about 0.030 inch from the surface. Balls of this type were tested in the dry mill only. Another set of forged SAE 1095 steel balls of 1-inch diameter was heated to 1500 F and quenched

Jan 1, 1961

By W. W. Fowler

ORIGINALLY designed for copper smelting only, the reduction works of the Cerro de Pasco Copper Corp. have been expanded over the years until now twelve different metals are produced, together with some seven other items which are used locally. Although the total tonnage treated is comparatively modest, as smelting plants go, the variety of operations makes one of the most complex and interesting metallurgical problems in the world. The original plant, at La Fundicion, operated from July 1906 until September 1923. In 1922 a new copper smelter was built at La Oroya, which produced its first copper on Nov. 23, 1922. It is in this plant, greatly enlarged, that metallurgical operations now center. La Oroya is situated at the junction of the Cerro de Pasco Railroad and the Ferrocarril Central del Peru, at an altitude of 12,175 ft.-well over two miles. Many of the various operations stem from two principal smelting circuits which are themselves of conventional types. Copper ores and concentrates are roasted, smelted in reverberatory furnaces and converters, and blister copper produced. Lead ores, concentrates, and other materials are sintered, smelted in blast furnaces to crude lead which is partially fire-refined, and finally electrolytically refined by a modified Betts process.

Jan 1, 1945

By James C. M. Li, J. Weertman

James C. M. Li (United States Steel Covp.)—The author has discovered a single analytical relation between the minimum, or the steady-state, creep rate and the applied stress confirming a statement made earlier by orn" that such relation should exist and should reduce to the power law at low-stress levels and to the exponential law at high-stress levels. However, as pointed out by the author, all the available theories of creep are not adequate to explain such a single relation. Inspired by such a statement, I have made a suggestion concerning a possible explanation13 of the new relation. This is based on the concept that the rate-controlling step is the cooperative motion of a short dislocation segment. The nature of and the reason for the cooperation have been discussed13 as well as the reason why the motion of the dislocation could be controlled by the mobility of the short segments. A natural short segment has been proposed13 to be the node formed at the intersection of two dislocations. The reason why the node may contain only a few atoms has not been discussed and the application of the proposed model to all the metals and alloys reported in this paper has not been attempted. It seems appropriate to include these in this discussion. The model was partly inspired by the substructure recently observed in the electron microscope on creep specimens. One such example is shown in Fig. 48 in Darken's Campbell Memorial Lecture. The substructure is a collection of dislocation intersections and irregular networks. No pileups have ever been observed in such specimens. A closer look at the network indicates that one set of dislocations is more straight than the other set sug- gesting that the other set may be mobile in the plane of the net. Since, for the network to survive the creep deformation, some dislocation reaction has to take place at the intersection of the two sets of dislocations, the mobile dislocation, even if it can slip in the plane of the net, will have difficulty in moving at these intersections. To illustrate, an idealized network is shown in Fig. 9. The thin lines represent the set of dislocations which are mobile and can slip in the plane of the net except at the nodes which are formed at the intersection of the two sets of dislocations. The other set of dislocations, represented by the thick lines, may have a Burgers vector which is not parallel to the plane of the net, and therefore may be immobile. Because of this nonparallel Burgers vector, the Burgers vector of the node, which is avectorial sum of the Burgers vectors of the two sets of dislocations, will also be nonparallel to the plane of the net. Therefore, the node cannot slip in the plane of the net and the set of mobile dislocations will have to drag the node along as indicated in Fig. 9. Now the problem is how many atoms could be involved in the nodes. Exact calculation of the length of the node is a difficult task especially since the length should be a steady-state length and not an equilibrium length. An estimate of the equilibrium length can be made by balancing the line tension of all the dislocations. The results would be a small fraction of the length 1 between nodes as shown in Fig. 10. In some instances such a calculation shows that the node will not be formed. But, since the calculation is only approximate, it does not rule out the possibility of the formation of a short node. In other instances the equilibrium length of the node is an appreciable fraction of I. Such a node would

Jan 1, 1963

By AIME AIME

WTHIN the next month all members of the Institute will be given an opportunity to vote for a new President, two Vice-Presidents, and five Directors. All of the candidates nominated by the official committee are well known to certain groups of the Institute membership but a brief record of their professional lives will be given here for the information of those that will vote. Not since 1927, when Everette DeGolyer guided the destinies of the Institute, has a member of the Petroleum Division been a candidate for President. John Meston Lovejoy has been a Director since 1930, and a Vice-President as well for the last year: In the three years 1932-4 lie was also chairman of the Admissions Committee. Dir. Lovejoy graduated from the Columbia School of Mines in 1911, just before lie was 22 years old, and began his professional career as a copper miner at Chuquicamata. Chile. Silver and gold mining later claimed his % attention, and it was not until 1914 that lie gut into the oil business, as geologist for the Standard Oil Co. of N. Y. This took hint to China and he later worked for the company in Wyoming. In 1917 lie joined the Army where lie rose to be captain of Field Artillery. Upon his return to the United States he went to work for the Amerada Petroleum Co., of which he later became vice-president and general manager, with headquarters in Tulsa. Since coining to New York he has been president of the Petroleum Bond & Share Cu.. and is currently president of the Seaboard Oil Co.

Jan 1, 1935