Search Documents

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Edward Judd

CANADA'S mining industry is rapidly recovering from the depression through which it passed in 1921. Its total output of $183,029,600 in 1922 was 6.4 per cent. greater than that of 1921, and was exceeded by only three previous years, 1917, 1918, and 1920. Table 1 compares the output of a few of 'the more important items selected from preliminary data published' by the Dominion Bureau of Statistics. TABLE 1.-OUTPUT OF CERTAIN MINERAL PRODUCTS IN CANADA PER CENT. 1921 1922 CHANGE Cobalt, metal and in compounds, lb 252,000 443,800 +76.1; Copper contents of blister, matte, and exported ores, lb 47,620,820 43,321,400 - 9.0 Refined copper, lb 4,286,000 730,000 -83.0 Gold, fine oz 926,329 1,230,985 +32.8 Pig iron, sh. tons 665,676 429,024 -35.5 Lead, sh. tons 33,340 47,085 +41.2 Nickel contents of matte, etc., lb. 19,293,060 17,496,490 - 9.3 Silver, including that in base bullion, gold bullion, etc., fine, oz. 13,543,198 17,611,646 +30.0 Zinc (nearly all refined), sh. tons. 26,545 28,199 + 6.2 Asbestos shipments, sh. tons 92,761 136,657 +47.3 Coal, all grades, sh. tons 15,057,500 15,045,300 Gypsum shipments, sh. tons 386,550 441,160 +14.1 Natural gas, M. cu. ft 14,077,600 14,954,100 + 6.2 Petroleum, bbl : 187,540 178,570 - 4.8 Cement, bbl 5,752,885 6,943,968 +21.0 Brick, structural, all kinds, M. , , 109,009 127,137 +17.0 On the basis of estimated market values, the whole output of 1922 was contributed as follows: Metals, 33.4 per cent.; non-metallic minerals, 45.1 per cent.; structural materials and clay products, 21.5 percent.; this distribution indicates a return of the metal mining. industry nearly to the position of relative importance that it occupied. before 1921, in which year metals contributed only 28.7 per cent. to the total value. of output while non-metallics gave 51.1 per cent. Canadian cobalt originates entirely in the ores of the Cobalt district, which are mainly treated at smelters in southern Ontario, although some quantities of residues have been exported to England and Europe. Exports during 1922 increased even more than production, consisting of about four-fifths . cobalt oxides and salts, and one-fifth of cobalt alloys and other metal combinations.

Jan 8, 1923

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By J. W. Schroeder

SEAMLESS pipe, the product produced from piercing a solid round billet of steel by the Mannesmann process, was first produced in the latter half of the 19th century, the Mannesmann machine having been patented in 1885. The products of other processes also have been termed seamless pipe; for example, the cylindrical section produced by "cupping," which consists of forming a cup from a flat plate or disk and further elongating the cup into a tube by passing it through a set of reducing dies. The purpose of this paper is to discuss some of the more important metallurgical factors and their relationship to the economical production of seamless pipe produced by the Mannesmann piercing process. The first seamless tube plant in America was established at Shelby, Ohio, in 1891, and was employed in the manufacture of bicycle tubing. For a number of years the bicycle industry was the only user of seamless tubing, and this tubing was produced by hot-rolling pierced billets imported from Europe and finishing on the cold drawbench. At the turn of the century, the automotive industry was responsible for an increase in the demand for seamless tubing. The growth of this industry was the dominant factor leading to the phenomenal growth of the petroleum industry, which in turn created a tremendous demand for seamless pipe. In addition; the old lapweld iron boiler tubes for stationary and locomotive boilers were replaced gradually by seamless tubes. Since 1929, the production of seamless steel pipe and tubes has increased over loo pct. In 1929, 1,459,9031 net tons of seamless pipe was produced, including both hot-finished and cold-drawn material, as compared with 3,087,3122 net [ ] tons in 1948. Table I gives the distribution of seamless pipe by classes for 1948. METALLURGICAL PROBLEMS From a metallurgical standpoint, the production of seamless pipe has presented many problems. Practically every type of steel, carbon and alloy, with the exception of the superalloys developed during World War II, has been pierced and rolled successfully into tubing. This includes bessemer, open hearth, by the stationary and duplex processes, and electric steels. The range of sizes produced is no less staggering to the imagination, when it is considered that the hypodermic needle, which is 0.016 in. diam with a wall thickness of 0.004 in., and pipe for gas or oil transmission lines, with a 26 in. OD, are both seamless tubes. Between these extremes, the range of diameters and wall thicknesses meets most present-day demands for seam-

Jan 1, 1951

By M. E. Hassan, J. C. Calhoun, R. F. Nielson

An apparatus was constructed for the measurement of inter-facial tensions over a range of temperatures and pressures. This apparatus utilized the pendent drop method, and resembles in construction similar apparatus recently described in the literature and in use in some petroleum research laboratories. The interfacial tensions of benzene, propane, n-pentane, n-hexane. n-octane. and iso-octane against water were measured at temperatures ranging from 26" to 82" C and at pressures ranging from 1 to 204 atm. Values of interfacial tensions for the henzene-water system and their variations with temperature and pressure are generally in good agreement with value? of previous investigations. The data in all cases showed a slight decrease of interfacial tension with pressure at constant temperature in the range studied. The effect of pressure became less as the pressure was increased, with an indication of a reversal of the effect at higher pressures. There was a decrease of interfacial tension with temperature at constant pressure in all cases, as would normally be expected. This rate of decrease became greater the higher the temperature. A general equation is presented for the interfacial tensions as a function of presPurp and temperature over the range studied, and the constants calculated for each system. A definite trend was found in the effect of molecular weight on the interfacial tension at a given temperature and pressure, for the homologous series from propane to n-octane. Data for n-decane from the literature fitted well into this trend. INTRODUCTION It has been recognized for many years that surface forces play an active part in the production history of an oil reservoir as well as in determining the amount of unrecoverable oil. The magnitudes of these forces are governed by the values of the interfacial tensions. These vary greatly with composition, pressure, and temperature. The effect of composition is greater than that of pressure and temperature over the ranges normally encountered. In fact, because of the variety of compounds present in a crude, no attempt has yet been made to correlate crude composition with its surface tension or with its interfacial tension against water. The amount of dissolved methane greatly affects the surface properties of an oil, and there are "surface-active" compounds in crudes which have a much greater effect on boundary tensions than do equal amounts of hydrocarbons. The purpose of the present work was partly to contribute data that would eventually be used in correlations applicable

Jan 1, 1953

By J. Rogers, K. L. Sutherland

THE relationships between collector and mineral, activator and mineral, and activator, collector and mineral will be considered herein. We propose to criticize current theories of flotation but we will not repeat the many pertinent arguments presented by Wark and Cox28 in 1937 in which the "chemical" or more strictly the "solubility" theory proposed by Taggart and co-workers22 is shown to be untenable. Recently Taggart, Arbiter and Kellogg24 have studied the long-chain aliphatic amines as collectors and have attempted to resuscitate the solubility theory for these particular collectors. Dean and Ambrose3 have felt that "we stumble over words" when we distinguish different mechanisms of adsorption. Our view is that nothing is more stultifying to the development of a science than attempts to force widely different phenomena into one classification. This oversimplification leads immediately to difficulties in the interpretation of results. EXPERIMENTAL PROCEDURE The response of minerals to activator and collector was determined by "captive-bubble" tests. The methods of preparation of specimens26 and of testing18 have been previously described. Results from captive-bubble tests were confirmed by flotation tests in glass-stoppered cylinders.25 The full lines shown in the figures relating solution composition to contact (flotation) distinguish solutions in which contact (flotation) is possible from those in which it is not. The curve is derived by successive approximation and the accuracy is ±0.2 pH units and ± 5 mg. per liter of collector or depressant. Solution compositions for which it was shown experimentally that contact or flotation is possible are marked by a circle, those for which it is not possible by a cross and those for which it is doubtful by a cross within a circle. It is assumed that at all other solution compositions within (without) the curve, contact or flotation is possible (not possible). After testing in the collector solution, the mineral was removed, washed, and tested by the captive-bubble method in water, or floated in a cylinder with frother only. In this way the composition of solutions in which a mineral was conditioned but in which properties of the collector solution prevented contact or flotation can be defined. The composition of solutions in which conditioning was possible lie between the full and broken curve, the experimental results being indicated on the figures by a square. The curves show the limits of composition of solution in which flotation in a cell would be possible. Many factors other than those considered in these tests determine recovery or grade of a given mineral in practice.

Jan 1, 1947

By B. M. Burchfiel

CALIFORNIA possesses such an abundance of ceramic materials other than clays, that she is quite independent of other states and foreign countries so far as these materials are concerned. Certain users import some feldspar, silica, and allied minerals, but they do so from choice and not necessity. Production is largely for home consumption, so the total volume of ceramic materials produced is comparatively small. Many small deposits of the materials here under discussion are worked by individuals, and their output sold to individual grinding companies or users. The data given here shall be confined to the larger deposits and developments because they give a truer picture of typical deposits, operations, and materials.

Jan 1, 1936

By B. B. Zavoico

During 1936 the Russian oil industry made very satisfactory progress and, while not all difficulties of organization have been ironed out, the country is now assured of a supply of petroleum products in sufficient quantities and of quality demanded by modern motor equipment. The year 1937 promises to better by a wide margin the good showing of 1936. The statistics given in this paper for the first time take into consideration the varying gravities of crude oils of the several Russian oil fields instead of using a flat conversion factor of 7 bbl. per metric ton. It was found from the detailed study that the generally used average conversion factor should be increased from 7 to 7.25 bbl. per metric ton, the figure varying, of course, with the gravity of oil in the individual fields. Crude-oil production during 1936 is estimated at 201,500,000 bbl. as compared with 182,970,000 bbl. produced in 1935, an increase of 9.4 per cent. The greatest increase was again recorded in the Baku district, which increased its production by 10.9 per cent, from 141,257,000 bbl. in 1935 to 158,300,000 in 1936. Grozny district maintained its production at a level of about 23,000,000 bbl., but its old fields continued to decline and production was sustained by the development of newer fields. A great advance was made in drilling speeds and the total footage in 1936 reached 6,694,200 ft. as compared with 4,926,600 ft. drilled in 1935, an increase of 26.4 per cent. In older deep fields, producers were being completed at over 8000 ft.—a great depth for Russian drillers but two years ago. Several major discoveries were made in 1936. Northeast Caucasus.—Izberbash, east from Grozny and on the Caspian Sea, was the outstanding discovery, the initial production of the discovery well being around 3000 bbl. per day from about 5000 ft. The importance of the field is due to the large area of the structure, half of which, however, is under the sea, and also to its strategic location on the shores of the Caspian and near a trunk pipe line to the Grozny refining center. An active development program is being pursued in Izberbash and its 1937 production quota is set at 7,500,000 bbl. Achi-Su field, near Izberbash, also discovered during 1936, while not as prolific as Izberbash, is thought to cover a very large area and the small

Jan 1, 1937

SULPHUR is a very well known mineral and apparently is produced in many places. It is engendered from an unctuous earthy and powerfully hot substance so that it is considered among experienced workers to bear a resemblance to the element of fire. This is called by these same men the masculine seed and the prime agent of Nature in the composition of metals. Because of its great dryness and heat it has, as experience shows, affinity with fire, which is easily introduced in it when brought near. And once introduced the fire is quenched only with difficulty before its unctuousness is wholly consumed. Although it shows itself to us of such a hot and dry nature, we must not think that sulphur is a substance so pure that it can stand by itself or that in order to attain its form it has no need of its portion and part of moisture like every other mixture. This is shown to us by its easy fusion, in which it resembles the metals. This thing is found in many places and in many varieties of color; some are white, others yellow and orange, and some others between gray and black. They also say that some red is found. It does not occur in that arrangement of veins like other minerals, but most liberal Nature makes whole mountains of it as is seen in the Aeolian islands, [26] near Sicily, in Etna or Moncibello which is the island of Sicily, at Pozzuoli, in the territory of Rome, in the Sienese domain at San Filippo, and in many other similar places. It is a substance that has a very strong odor and is most unpleasant to smell. It is very fixed in its substance so that it is never corrupted by time, by boiling, or by the moisture of water. For although it may stand in water a long time it never becomes soft nor does it ever decrease or increase in weight. It is brittle and easily crushed very fine. It is said that a trace of garlic rubbed on the mortar helps anyone who wishes to reduce it to impalpability. Its ores have a form more like earth than like stone although they some¬times have the color of a certain soft rock. The places where it is found are easily recognized by the great odor that they give out and by the very hot baths that often spring forth near it. What I have already told you about quicksilver that is contrary to the

Jan 1, 1942

Granduc lies near the Alaskan border in British Columbia, about 600 miles (960 km) north of Vancouver. Prospecting in the area must take place in the short summer months of fog and rain because the winter is bitter cold, with snowfall up to 960 inches (24.4 m) accompanied by avalanches. Despite these difficulties, the mineral ized area was discovered in the 1920's. By 1956, Newmont Mining Corporation had developed mineable ore reserves estimated at 32,500,000 tons of 1.93% copper. Newmont and ASARCO, in a joint venture, then began development of the ore body, which was partially covered by glaciers. It was apparent a concentrator could not be built at the mine site where overland access was impossible due to the weather conditions and the terrain. Years of engineering studies of all possible access routes finally dictated the driving of an 11 mi long (17.6 km) tunnel passing under three glaciers and three mountain ranges to the nearest feasible concentrator site at Tide Lake. Even then, a mountain road subject to an average snowfall of 800 in. (20. 3 m) had to be built 32 mi (51 krn) from the concentrator through Alaska to Stewart, British Columbia, the nearest port. At Stewart, which is located at the head of a fjord 120 mi (192 krn) from the Pacific Odean, a fully equipped marine terminal was built. The tunnel, the lifeline between mine and mill, was to be driven from both ends; however, in 1965, an avalanche occurred at the Leduc portal, killing 26 crew members and wrecking much of the camp. The tunnel was then driven from one heading adjacent to the concentrator site at Tide Lake, a distance of 53,744 ft (16,381 m) to a point under the ore body. The remote location, type of terrain, and bad weather made supply of crews, equipment, and construction materials difficult; but in spite of these extremely adverse conditions, the tunnel crews set many world records. Mineralization throughout the ore zone is generally uniform in grade and composition and is primarily chalcopyrite and pyrrhotite associated with pyrite. Mining is mainly by sublevel caving. After blasting, rubber-tired load-and-haul equipment moves from level to level by means of an internal connecting ramp system on a 15% slope. At the gathering haulage level, 15-ton bottom-dump cars deliver the ore to a 600-ton pocket equipped with a Hudson "Rock-Flo" dump. The bottom of the ore pocket forms the feed chute to the primary

Jan 1, 1978

By J. M. Sands

Production of oil in Oklahoma during 1927 amounted to 273,256,900 bbl. (Table l), an increase of nearly 100,000,000 bbl. over the previous year. All of the major fields declined with the exception of those of the Seminole district which produced 136,105,000 bbl., almost one-half of the total production of the state. Because of this large new production, most of the development in the state during the year took place in that district. The Seminole City pool located in T.-9-N., R.-6-E., was the first of these pools to be developed. The Indian Territory Illuminating Oil Co. brought in the first well in this field in March, 1926, for 1100 bbl. This well is located in Sec. 24-T.-9-N., R-6-E., and produced from the Hunton lime reached at depth of 3900 ft. The first Wilcox production was developed by the Independent Oil & Gas Co. and R. S. Garland in Sec. 26, T.-9-N, R-6-E. This well was being drilled for production in the Hunton lime but was dry in this horizon and was deepened to the Wilcox sand in July, 1926, and at the total depth of 4069 ft. developed a maximum production of 8000 bbl. daily. It held up in wonderful manner and was the cause of not only the development of this pool but the prospecting of the whole district for the Wilcox sand. This led to the discovery of the other major pools in that district. Seminole City pool reached a peak production of 264,500 bbl. on February 22, 1927, and slowly declined so that by December it had a daily average of 56,200 bbl. from 321 wells. The second pool in this district to be discovered was the Searight pool which was discovered by F. J. Searight et al. in Sec. 33, T-10, R-6, in April, 1926. The first well was drilled to the Hunton lime encountered at 4115 ft., and came in for 1300 bbl. daily. During August, 1926, the second well was drilled on the same farm through the Hunton lime to the Wilcox sand which was encountered at 4360 ft. It came in for an initial production of 4000 bbl. daily. This started active drilling in this field for the Wilcox sand. The field had a peak production of 40,621 bbl. on June 15, 1927, and declined to a daily average of 22,300 bbl. from 73 wells during December.

Jan 1, 1928

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949

By McHenry Mosier

MeRcuRy is one of the strategic metals of which the supply has been raised from critical uncertainty to more than enough for essential demands. Work by the Bureau of Mines has contributed substantially to increased production of mercury in the United States and to consequent accumulation of Government stocks. Other contributing factors have been higher prices for mercury and Government loans to operators. The Bureau has undertaken 13 exploration projects, 10 of which have been completed. This work has comprised 28,376 ft. of several types of drilling and 23,798 lin. ft. of surface trenching, and has indicated commercial ore containing 34,800 flasks of mercury and marginal ore containing 26,200 flasks, a total of 61,000 flasks; equivalent, respectively, to domestic production for 8 months, 6 months, and 14 months. As Government stocks are now adequate, domestic production (currently at the rate of 50,000 flasks per year) is gradually being curtailed through Government control of labor and operating supplies. Introduction Mercury was one of the seven metals designated as strategic by the Army and Navy Munitions Board in 1939, when Congress appropriated funds for the investigation of domestic sources of supply of war minerals. The Bureau of Mines immediately started a limited search for strategic minerals, but the first mercury project was not begun until December 1940. The U. S. Geological Survey assisted in the search for cinnabar by contributing information on domestic mercury deposits, preparing maps, and making geological studies of exploration projects. The present high rate of production of mercury in the United States was encouraged by the increase in price to $196 per flask at New York (Fig. I) and Government loans to operators for mine development and plant construction. The Bureau of Mines has issued, for restricted distribution subject to wartime controls, 13 War Minerals Reports on individual mercury deposits (listed in appendix A). In March 1942 it also published a Progress Report of the Metallurgical Division, R. I. 3627, Cinnabar-reduction Plants of the Southwestern Arkansas Quicksilver District. Uses of Mercury Mercury and its compounds have more than 3000 uses. Its principal use is as a catalyst in the manufacture of gases for chemical warfare; the next largest is in pharmaceuticals. Mercury is essential also for: (I) certain electrical apparatus, (2) industrial control instruments at many war plants, (3) munitions, including blasting caps, (4) insecticides in agriculture, (5) antifouling paint for ship bottoms, (6) dental preparations, (7) general laboratory use, and (8) amalgamation of free-milling gold ores.

Jan 1, 1949

By John R. Anderson, Michael B. Bever

CARBON may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,1 the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. EARLIER DATA The solubility of carbon in molten pure copper is about 0.0001 pct at 1100 °C and 0.0004 pct at 1475°C.1 Various authors2-6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range 1217° to 1245°C. This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Michael B. Bever, John R. Anderson

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By John R. Anderson, Michael B. Bever

Carbon may affect the alloys of copper in several ways. Provided an alloying element does not oxidize preferentially, even minute quantities of carbon dissolved in liquid alloys of high copper content will form insoluble carbon oxide gases under oxidizing conditions. Gas porosity in castings of high-copper alloys can originate in this way. In certain alloys of low copper content carbon may have considerable solubility and may be an effective deoxidizer. In these alloys carbon will tend to suppress porosity. Carbon that is dissolved in the molten alloy is likely to be retained in the solidified metal. The effects of carbon on the physical properties of the metal are determined by the form in which it is present. Depending on the alloying elements and also on the cooling rate, carbon may precipitate as graphite, may form a carbide or may remain in solid solution on cooling. As solid copper does not dissolve a measurable amount of carbon, a carbon-bearing solid solution can occur only if the copper is alloyed with a large excess of an element that forms such a solution. The effect of graphite or of carbides on the properties of an alloy will depend on the size and distribution of the precipitated particles. As Hensel pointed out in discussion,' the formation of an alloy carbide may interfere with the age-hardening properties of a copper alloy. One would also expect that the presence of carbides or of graphite will under certain conditions promote corrosion or high-temperature failure in nonferrous alloys. Since carbon has an effect on the soundness of castings and affects the structure and behavior of solid copper alloys, its solubility in the liquid alloys is of practical importance. The isothermal change of carbon solubility with alloy composition is of interest from a theoretical standpoint. The binary alloys of copper with manganese and with nickel are used industrially and serve as a base for more complex alloys. The solubility of carbon in each of these metals is known, but its solubility in their alloys has not been determined. Earlier Data The solubility of carbon in molten pure copper is about o.oooi pct at II00°C and 0.0004 pct at 1475°C.l Various authors2""6 have published data on the solubility of carbon in molten manganese. There is agreement on a value of about 6.7 pct in the temperature range r2170 to 1245°c This solubility value corresponds to the formula Mn3C. It increases very little with increasing temperature. Corson7 states that carbon is soluble in copper-manganese alloys and that the

Jan 1, 1947

By Bever M. B., Floe Carl F., Hung Liang

Data on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Simsl have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett5 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid iron were reported in 1910-191 1 sieverts and Krumbhaar8 and by sieverts.9 They found that 100 grams of iron absorbs 28 c.c. of hydrogen at 1550°C and One atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 C.C. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon are not available. Martin1' investigated

Jan 1, 1947

By Harold Margolin, W. R. Hibbard, R. W. Fenn, H. P. Moore

Deformation lines, also called etch markings or strain markings, are non-effaceable lines developed in individual grains by etching a metal specimen which has been cold worked sufficiently to cause atomic non-conformity or slight orientation differences within the grains. Etching occurs more rapidly at these lines of high chemical reactivity to produce a result similar to that revealing grain boundaries. Wider etching effects forming bands have been found. They are believed to be bands of deformation lines which form areas of measurably different orientation from the crystal matrix. The crystallite rotations causing these bands have been shown by Barrett2 to contribute to deformation textures. Although deformation lines have been observed in many metals, the amount of deformation requireti for their appearance has been established only in general terms. Mathewson and Phillips3 observed the first appearance of deformation lines in cold-rolled alpha brass at about 20 pct reduction in thickness using the standard ammonium hydroxide hydrogen peroxide etchant. Price and Davidson4 noted defor- mation lines in common high brass after 26.5 pct reduction by cold rolling using the same etchant. Johnson6 observed dark thick forklike lines in 99.99 pct pure copper reduced 31.8 pct. Adcock6 observed deformation lines in 80-20 copper-nickel alloy rolled 50 pct. Samans7 found no deformation lines in alpha brass single crystals cold rolled 9.5 pct but they did appear after 25 pct reduction using ammonium hydroxide and hydrogen peroxide etchant. Barrett and Levenson8 observed deformation bands in drawn polycrystalline iron at very small reductions in area and noted that their initial appearance perhaps depends on grain size and other conditions. They reported deformation bands in a single crystal of iron reduced 6 pct by drawing. Brickg noted that deformation lines in 70-30 brass apparently associated with I I I I ) planes appeared after reductions of from 20-50 pct by cold rolling. Brick and Williamson10 noted that in single crystals of 70-30 alpha brass "as in polycrystalline brass, no deformation markings appeared until reductions exceeded 20 pct." Cook and Richards" reported that in Copper cold rolled less than about 50 Pet few strain markings were apparent but for higher reductions many strain markings appeared transverse to the rolled direction. In a review article Brick and Phillips12 noted that previous studies had not shown deformation lines in cold rolled alpha brass below 20 pet reduction and added that 4

Jan 1, 1949