Search Documents

By K. P. Gupta, P. A. Beck, N. S. Rajan

By determining the a phase boundaries in the following ternary systems: V-Fe-Si (at 1175oC), V-Co-Si (at 1175°C), V-Ni-Si (at 1175oC), Cr-Mn-Si (at 1000°C), Cr-Co-Si (at 1175°C), Cr-Ni-Si (at 1175°C), V-Fe-A1 (at 1175°C) and Cr-Co-A1 (at 1175°C), it was found that Si exerts a stabilizing effect on these a phases, while A1 tends to destabilize them. Si atoms in solid solution occupy sites D in the a structure, The co/ao ratio increases with increasing Si-, Mn- or Fe-content. The volume of the unit cell decreases with increasing Si-content. THE stabilization of certain metal silicides (the Nowotny phases) by the addition of relatively small

Jan 1, 1961

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By H. W. McQuaid, E. W. Ehn

It is usually assumed that chemical specifications are sufficient for steel to be used for case carburizing, and if the steel analyzes within the ordinary limits specified for steel for this purpose, no difficulty traceable to the steel used should be encountered in obtaining satisfactory results in the case carburizing and hardening. Much work has been done to determine the effect of various alloying elements on the rate of carbon penetration, etc. but, to our knowledge, little if anything has been published in regard to the effeet of the quality of the steel on the final results in the hardening of case-carburized steel parts. The writers believe that the structure of the case both before and after quenching is greatly affected by the actual condition of the steel itself as made, and that for good results in the case-carburizing and hardening departments, the steel should be of the best possible quality as regards non-metallic impurities. It is the purpose of this paper to prove that the presence of excess dissolved oxides in the steel, as made in the melting furnace, affects permanently the results obtained in carburizing and hardening and that it is possible that the presence of dissolved oxide call result in total unfit-ness of low-carbon steel for case hardening purposes. When races and rolls for roller bearings are made from a low-carbon steel, case carburized and hardened, it is of primary importance that the results of this treatment be of the highest quality. It is necessary, therefore, that in the case-carburizing work each detail be rigorously checked to avoid any defects which would cause the loss of much time and material. The case carburizing with which this paper deals was done in under-fired oil furnaces. The temperature of each furnace is controlled by means of a platinum platinum-rhodium thermocouple, in connection with a potentiometer indicator and potentiometer recorder. The temperature of each furnace is registered every 15 min. by an operator, who is continually checked by the automatic recorders.

Jan 1, 1922

By I. R. Kramer, L. J. Demer

Aluminum single crystals were pulled in an electrolytic cell allowing surface removal during the deformation. The extent of Stages I and 11 of the stress-st-aitz curve was increased and the slope decreased as the rate of metal removed from the surface was increased. An increase of the strain rate caused a decrease in the effectiveness of the metal removal. The data indicate that the work-hardening coefficient in Stage I is determined primarily by the conditions which exist on the surface of the crystal. In Stages 11 and 111, both surface effects and internal barriers are important. ALTHOUGH numerous investigations have been conducted on the plastic flow characteristics of metals in an attempt to explain the mechanism of work-hardening, relatively few studies have taken into account the influence of the surface. In all current theories of work-hardening it is assumed that the impediments to the movement of dislocations are within the crystal. The barriers due to the surface and the existence of solid and liquid films have been neglected even though it has been demonstrated that the surface exerts a large effect. A number of investigators1-l8 have shown that solid films on the surface of single crystals markedly affect their mechanical behavior. In general, the presence of a solid film tends to increase the yield stress and increase the work-hardening rate. Often, on single crystals, Stage I and, at times, Stage II regions are completely suppressed. Various mechanisms have been offered for the effects of oxide and metal films as well as the influence of electrolytes. Of these, concepts concerned with the locking of surface dislocation sources and the blocking of dislocations at the surface resulting in pileups appear to be actively considered at present. Barrett,11 Takamura,6 Gilman,19 Lipsett and King,20 Shapiro and Read,10 and Weiner and Gensamer21 are among those who have interpreted their results in terms of piled-up dislocations at the surface, while Adams.22 and Chalmers and Davis23 have explained their experimental observations in terms of locking of surface dislocation sources. In general, the change in plastic flow properties due to electrolytes has been explained in terms of the unblocking or unlocking of dislocations by the removal of the oxide films. In considering the two proposed mechanisms, it appears that the locking of sources of surface dislocations by a solid film should exert a primary influence only on the critical resolved shear stress for flow and not on the slopes of Stages I and 11. However, the blocking at the surface of dislocations from internal sources may also affect the critical resolved stress and furthermore exert an influence throughout the whole plastic range. In certain cases it does not seem feasible to explain the results of experimental observations in terms of locking of surface dislocation sources. The abnormal aftereffects found by Barrettll,12 by removing the oxide by an acid treatment are excellent evidence of the blocking of dislocations at the surface. Additional evidence in favor of a blocking due to a pileup of dislocations at the surface may be found from the observations that the critical resolved shear strength continues to increase with the thickness of the oxide layer until very heavy oxide layers are formed. If the locking of surface dislocations sources were the dominant factor, the critical resolved shear stress would not be expected to increase after all of the surface sources were locked by the formation of the oxide. This may be expected to happen after a few atomic layers of the oxide are formed. In spite of the above evidence on the strong influence of the surface on the plastic flow characteristic, this has been ignored in current theories of work-hardening. Seeger24,25 suggested that most of the dislocations may slip out of the crystal only when the specimen axis is within certain areas of the orientation triangle. In other areas the resolved shear stress in other glide systems is large enough to generate dislocations which can form Lomer-Cottrell locks, thereby decreasing the average slip distance in some directions and causing a larger hardening rate. Friede126 assumed that at the beginning of Stage 11, a large number of Lomer-Cottrell dislocations are formed by a catastrophic process which used up all the Frank-Read sources on the secondary slip-planes. In this manner a fixed number of Lomer-Cottrell locks is formed which act as barriers against which the dislocations can pile up. In Stage 111, Seeger24 and Diehl, Mader, and Seeger25 proposed that Lomer-Cottrell barriers are circumvented by the cross slip of extended screw dislocations. Cottrell and Stokes,27 Friedel,26 Cottrell,26 and stroh29 suggest that the Lomer-Cottrell dislocations collapse under the stress field of the dislocation pileup. It is the purpose of this paper to report the changes in Stages I, II,and III of the deformation process in

Jan 1, 1962

By Robert L. Slobod

In much of the work reported in the literature on long cores. true connate water value, probably have not been obtained because of insufficient flow of 011 to attain equilibrium. A -.satisfactory method for establishing connate water in long cores has been developed in which oil flow is maintained until no additiona1 water is displaced. INTRODUCTION Long cores have been used by sev-erals investigators in an effort to evaluate the efficiency of oil recovery for various producing schemes. The effects of many variables such as rate of displacement. pressure drop, volume of displacing medium, gas-oil ratio, inter-facial tension, and others have been investigated, and the merits of gas drive have been compared with water drive. In the older experiments no connate water was used. but in the more recent stndies the philosophy of the experiment calls for a core containing oil and connate water (irreducible water) as the starting point of the experiment. The method generally used to establish this condition in long cores involves dynamic' displacement wherein one or more phases are forced through the core. flow being maintained at a constant rate or at a constant pressure until a steady state is reached wherein there is no change of saturation with time. It is one purpose of this paper to point out that in much of the work reported in the literature true connate water values probably have not been obtained. The reason for this failure is pointed out. and a method for obtaining more reliable connate water values on long cores is presented. It is impossible at this time to completely evaluate the effect on the conclusions in the earlier papers resulting from the failure to obtain true connate water in the long cores, but some data are presented which indicate that serious errors may he present in many cases. MATERIALS AND APPARATUS Cores cut front outcrop sandstones (Strawn. Torpedo, and Elgin sandstones) with permeabilities of the order of 300 md were used. The major experiments were made with a core 18-in. long and 2-in. in diameter. Cores of the same diameter but only 12-in. long were used in a few tests? and in some work a core I-in. in diameter and 11-in. long was used. These materials were all somewhat bentonitic. 'To reduce the effect of such constituents, one of the cores (Torpedo No. 10) on which the most work was performed was acid extracted at the start of the experiment. Brine containing 50,000 ppm chloride and naphtha (Stoddard's Solvent) were used as the water and oil phases, respectively. The core was mounted in a rubber sleeve which forms the inner lining of a brass cylinder. In this arrangement2 the rubber sleeve is forced against the core by applying pressure to water in the annular space between the rubber sleeve and the brass cylinder wall. The core is therefore sealed in rubber so that all fluids introduced at the input end of the core flow through the core. With this equipment the core may be easily removed for inspection and analysis. Also, other cores may be introduced for study with no extra time for preparation such as is required when plastic mounting is used. When pressure or conductivity measurements are desired at intermediate points along tile length of the core, the brass cylinder comprising the outer jacket of the core holder is cut into section, of the desired length. Each section is then made up as an individual unit with its own rubber sleeve (see Fig. 1). The individual units are then butted up against a ring of plastic or other insulating material which carries an electrical contact for resistivity measurements and an opening which can be used for the measurements of fluid pressures. The individual units are forced tightly against the plastic ring separators and held in place with several tie rods. Inlet and outlet end butts of the same diameter as the core and several inches in length are provided to control the introduction and withdrawal of fluids and to complete the arrangement for sealing the core within the rubber sleeve. Fluid flow is maintained either by applying pressure to the liquid confined in a reservoir or by the use of a gear pump. The latter is preferable where continuous flow at a moderate rate over a long time interval is desired since a small volume of liquid can be readily recirculated using filters to prevent plugging of the core. EXPERIMENTAL The oven-dried core is weighed and is then completely saturated with brine

Jan 1, 1950

By H. I. Aaronson, W. L. Winterbottom, G. M. Pound

On the basis of a statistical thermodynamic treatment of the data of smithz2 on the activity of carbon in austenite, a Darken and smith23 deduced that the interaction energy, wy, between carbon atoms occupying nearest-neighboring interstitial sites is repulsive. Aaronson, Domian, and pound 24 (ADP) have applied two different statistical thermodynamic analyses to the same data. One analysis, a composite of the treatments of Darken and Smith,23 Speiser and Spret-nak," and Kaufman, Radcliffe, and Cohen,26 primarily takes account of the positional entropic effects of wy in dilute solutions. The other, due to Lacher 27 and Fowler and Guggenheim," is also applicable to more concentrated solid solutions. The equations which both analyses produce for a,, can be rearranged so that, when In a,, is plotted against the appropriate function of the carbon content of the austenite, the plot will have a slope of unity when the correct value of wy is employed. Since no other constant need be simultaneously evaluated in order to make this determination, ascertaining the most probable value of wy from Smith's data on the bases of these analyses was an elementary problem in least-squares statistics. ADP demonstrated that the wy's obtained from both analyses vary with temperature in a statistically significant manner. McLellan, Gerrard, Horowitz, and sprague 29 (MGHS), on the other hand, have recently made a new statistical thermodynamic study of a,, and have concluded from this study that wy is independent of temperature. The equation which they derived for a,, is: where 0 = ratio of the mole fraction of carbon atoms to that of iron atoms, z = number of sites from which occupancy is excluded by the presence of a carbon atom and the repulsive character of its interaction with nearest-neighboring carbon atoms (z = zb in Ref. 24), and x = a geometric parameter taking account of overlapping of the exclusion shells of nearby carbon atoms. z is 1 when wy = 0 and 13 when wy = Q. For a given value of z there is a definite value of X . In the absence of an equation connecting z and X, MGHS computed geometrically the value of x at several integral values of z; x increases from 0.47 to 8.67 as z is increased from 2 to 5. MGHS fitted Eq. [I] to the a,, data of Ellis, Davidson, and Bodsworth30 at 925° and 1050°C and to the data of smithz2 at 1000°C. Confining z to integral values in the range 4 to 6, and also somewhat restricting AG, the values of z, X, and AG were sought which would minimize the average root mean square percent deviation, D, of the calculated a,, values from those obtained experimentally. Finding that D was almost always smallest when z = 5, they concluded that z is independent of temperature. Since:23, 26 where R = gas constant and T = absolute temperature, and w,, was considered to be similarly invariant, this statement cannot be strictly true. The temperature range employed, however, was small and the interval between the values of z tested was sufficiently large so that the results could still be consistent with a constant The statistical treatment of the a,, data applied by MGHS is clearly quite approximate. Since more than three values of a,, are available at each temperature, z, and X, and AG have actually been over deter mined, rather than underdetermined as their treatment implies. In order to make more complete and exact use of the a,, data, we shall employ the Legendre Method of Least Squares, as described by Whittaker and Robinson. This technique permits conversion of the overdetermined system of equations produced by the substitution into Eq. [I] of the available pairs of a,, and 0 data at a given temperature into an even determined system. Solution of the latter system yields the most probable value of each of the three constants. This procedure will allow a statistically rigorous test to be made of the conclusion drawn by MGHS in respect of the temperature dependence of In order to obtain linear iiequations of conditions" from Eq. [I], the exact values of the three unknown constants are replaced by G/RT = =/RT + y, where z, i, and aG are estimated values of the constants. This allows the conditional equations to be written in the form:'l where fi -f6, i, =/RT) = the right-hand side of Eq. [I] for a given pair of ayi and values. When applied to Eq. [I], these relationships become: The i equations of condition are reduced to three "normal equations" in the manner discussed by Whittaker and Robinson. The normal equations are then solved for a, ß, and y. Both of these operations are most conveniently performed by means of the computer technique of Winterbottom and Gjostein.32 This technique was used iteratively until the value of 0 (the most sensitive of the three correction factors) became 10.01. (Until they became small, a, 8, and y

Jan 1, 1969

By W. G. Frailing, W. P. Sims

The Lakeview Pool of Kern County, California, was discovered in 1910 with the drilling of Lakeview No. 1 which blew out and produced an estimated 8,250,000 bbl of oil in 544 days of uncontrolled flow. The well has since been known as the Lakeview Gusher. Full exploitation of the pool did not take place until about 25 years later. A total of 112 producing wells were completed in the Lakeview sand through April 30, 1949. As of that date, about 30 per cent of the total wells drilled were still producing, with an average pool production rate of approximately 2000 bbl per day. The cumulative oil production was about 41 million bbl of oil, or 55.3 per cent of the tank oil originally in place. The pool is bordered on its down-structure side by a body of inactive edgewater and water production where present has been principally the result of coning. Since the depletion of the greater portion of the gas energy by the Lake-view Gusher, the pool has operated under gravity drive. Relatively high angle dips, good permeabilities and favorable fluid characteristics have made gravity drainage particularly effective. Since January, 1942, the oil recovery -has been relatively constant at about 53,000 bbl per ft drop in fluid level. Correlations between the volume of reservoir space drained and the cumulative oil produced indicate that an ultimate recovery of 63.3 per cent of the tank oil originally in place is attainable. INTRODUCTION The Lakeview Pool is an outstanding example of gravity drainage. It is one of many productive reservoirs of the Midway-Sunset Field, and is located in Kern County, approximately five miles southeast of Taft and two miles north of Maricopa, California. Its position rel- ative to surrounding pools and to the Thirty-Five anticline is shown on Fig. 1. The northern portion of the pool lies in sections 32 and 33, Township 32 South, Range 24 East, Mt. Diablo Base and Meridian, while the southern portion lies in sections 25, 26, 35 and 36, Township 12 North, Range 24 West, San Bernardino Base and Meridian. As no two sections bear the same number, they will hereafter be referred to by section number alone. The purpose of this paper is to review the performance of the Lakeview Pool in an effort to evaluate the effectiveness of gravity drive as a recovery mechanism. REGIONAL STRATIGRAPHY AND STRUCTURE The oustanding structural feature is this area is the Thirty-Five anticline, the axis of which plunges South 75" East through the center of Section 35. As shown on Fig. 2, the following zones are oil and gas bearing in the Thirty-Five anticline area: Pleistocene Basal Tulare Tar Sands Pliocene San Joaquin Mya Sands Top Oil or Scalez Zone Etchegoin Kinsey Sand Wilhelm Zone Gusher Sand Calitroleum Sand Miocene Reef Ridge Lakeview Sand Sub-Lakeview Miocene Sands Monarch Sands or fractured shale equivalent Maricopa Webster Sand or fractured shale equivalent Fractured Shale-Uvigerina Zone C Obispo Sand and fractured shale equivalent Pacific Shale Zone The productive interval of the Lakeview Pool is limited to Upper Miocene and Lower Pliocene deposition. In this general area, the most prevalent type of accumulation results from stratigraphic traps or permeability pinchouts. As is the case of the Lakeview Pool, strati-graphic traps resulting from angular unconformities are present. The structure within the Miocene does not parallel that of the Etchegoin (Pliocene), as the Miocene beds were folded, and in places faulted, and subjected to erosion prior to Pliocene deposition. The Lakeview horizon consists of truncated sands which occur on the northeast flank of the Thirty-Five anticline. The direction of strike is west and northwesterly through sections 25 and 36 and continues northwesterly through sections 26 and 33, to the approximate center of section 32. At this point the strike swings to the northeast and the horizon re-enters section 33. in the northwest corner. The change in strike in section 32 affords synclinal accumulation at that point. The Lake-view sand is truncated updip by the Etchegoin overlap. To the southeast, the sand shales out, while to the northwest, the productive interval appears to be limited by a combination of stratigraphic pinchout and permeability barrier. Structurally, the Lakeview reservoir presents three areas of interest, as shown on Fig. 3. Area I in section 32 is a region in which a productive Sub-Lakeview Miocene sand is present. It occurs from 10 feet to 30 feet below the base of the Lakeview sand and attains a maximum thickness of 25 feet in Well No. 21, section 32. The producing characteristics of the Sub-Lakeview Miocene sand differ radically from those of the Lakeview sand. Water production at high structural locations and abnormally high fluid levels indicate that there was no communication with the Lakeview sand. Wells in Area I penetrated this sand and produced it in conjunction with the Lakeview sand. In Area 11, the Lakeview sand is a

Jan 1, 1950

By M. Cohen, D. J. Blickwede

Quantitative observations concerning the carbide phases in high speed steel are of importance for two general reasons: (1) the carbides, being inevitable constituents of the final structure, exert a direct influence on the properties of the steel; and (2) a substantial proportion of the total alloy content is tied-up in the carbides, and hence the extent of their solution on austenitizing governs the composition of the steel matrix. The latter relationship has a vital bearing on the response of the steel to tempering as well as on its performance in subsequent service. Accordingly, in the course of a long-term study of the behavior of high speed steels, the authors were confronted with the problem of securing quantitative data on the carbide phases. The obvious method for acquiring such information is to isolate the car-bides from the steel and subject them to chemical, X ray diffraction and other measurements. There are well-known extraction techniques which involve the chemical or electrolytic solution of the less noble matrix (ferrite, marten-site or austenite), thus leaving a residue of the carbide phases. However, the results obtained must be scrutinized carefully1,2 since the carbides may be affected by the chemical or electrolytic action. It is the purpose of the present paper to describe the experiments leading to an electrolytic-extraction technique for quantitatively isolating the carbides from both I and hardened high speed steel. Particular attention is paid to the amount, as well as the composition, of the carbides so that the matrix analysis becomes ascertainable by subtraction from the overall steel composition. Illustrative results are given for the M-2 grade of tungsten-molybdenum steel. Review of the Literature The chemical method of dissolving the matrix selectively with respect to the carbides makes use of dilute non- oxidizing reagents such as hydrochloric or sulphuric acid. Although this simple procedure has led to the determination of the cementite composition,3,4 it achieved only limited success because of the interaction between the acid and the carbide residue. Some of the carbides may not only be destroyed in this way, but the hydrogen released is likely to remove part of their carbon as hydrocarbon gases. The electrolytic technique of isolating carbides has the advantage of rapidly dissolving the specimen (anode) in the presence of less reactive solutions than are practicable with the chemical method. This reduces the possibility of chemical attack on the carbides, and furthermore, the hydrogen evolved during the electrolysis is released at the cathode which is not in close proximity to the carbides. The common electrolytes adopted for this purpose are hydrochloric and sulphuric acids.5-l1 Aqueous solutions of ferrous salts have also been used.12,13 A considerable advance in experimental technique was introduced by Treje and Benedicks14 who developed a double-compartment cell for electrolytic extraction, the anode and cathode chambers being separated by a porous diaphragm. A solution of 15 pct sodium citrate, 2 pct potassium bromide and 1 pct potassium iodide was selected for the anolyte, while the catholyte consisted of a 10 pct solution of copper sulphate, with copper serving as the cathode. This type of cell has a number of desirable characteristics: 1. The anolyte has a pH value close to 7, at least at the beginning of the run. 2. The iron that dissolves from the anode-specimen forms a water-soluble complex ion with the citrate, thereby preventing the precipitation of iron hydroxide (which would contaminate the carbide residue) despite the neutrality of the solution. 3. Copper deposition instead of hydrogen evolution occurs at the cathode, and this avoids an increasing concentration of hy-droxyl ions which (in an otherwise neutral solution) might cause the precipitation of insoluble hydroxides. 4. Contamination of the anode chamber by copper sulphate is inhibited by the porous diaphragm. Houdremont and coworkers15 applied the above method (with the further refinement of excluding oxygen during the electrolysis, washing and drying) to the extraction of carbides from a series of plain carbon steels after various heat treatments. They had quantitative success only with specimens in the annealed condition, and concluded that the size and shape of the carbide particles play an important role in the isolation process, with large spheroids exhibiting the least tendency to decompose during the electrolysis. Up to the present time, the citrate double-cell has not been used to any extent for isolating the carbides of high alloy steels, apparently on the grounds that the complex carbides are more resistant than cementite to attack in the simpler acid electrolytes. In particular, Bain and Grossmann7 and Gulyaev10.10a have employed the hydrochloric acid cell for their investigations of the carbides in high speed steel.* It will be demonstrated here that this type of cell is capable of yielding quantitative results in the case of high speed steel, and actually has certain advantages over the more complicated double cell. However, in order to provide a rigorous test of the quanti-tativeness of electrolytic procedures for the problem at hand, both methods were studied in considerable detail.

Jan 1, 1950

By Isaac Vera, Hans Ruge

The El Soldado copper mineralization occurs as relatively high-grade irregular ore bodies with assay contacts and with frequent inclusions of barren rock. The sampling methods must be timely for production grade control purposes, as well as accurate and inexpensive. Sampling techniques evolved from sampling dump cars at the haulage level to sampling Scooptrams at the loading pockets. These methods were abandoned in favor of sampling production blastholes. Several sampling alternatives are discussed. These involve the selection of optimum volumes and sampling frequencies while taking into consideration geological parameters and statistical analyses of sampling data.

Jan 1, 1985

By Louis D. Huntoon

SHORTLY after publication of the article in the July, 1924, issue Of MINING AND METALLURGY, entitled "Canada as a Gold Producer," requests were received to determine the ownership of production. Advices have also been received that considerable discussion has taken place on the same questions both in Canada and Great Britain. The author is indebted to R. H. Coates, Dominion Statistician, and George C. Bateman, Secretary, Ontario Mining Association, for the following figures and takes this opportunity of expressing his appreciation. There have been no statistics compiled as to ownership of production. Statistics were compiled as of Dec. 31, 1921 relative to the distribution of stocks, bonds and "other securi¬ties" in industrials, agriculture excepted, throughout the Dominion, and "distribution of ownership of securities issued by mining companies incorporated and operating in Ontario" for the same year. Stock registration does not necessarily represent actual ownership' as large blocks may be endorsed and not transferred; neither does registration actually represent production. When the charts are studied individually and collectively one cannot help but be impressed with the fact .that in the mineral industry of Ontario and the Dominion at large, Canadian registration predominates, the United States registration is about half that of Canada, and Great Britain is about half that of the United States. When the nickel-copper industry is excepted the British registration falls to a very low percentage. Since Dec. 31, 1921, British capital has commenced to flow into mining enterprises in Ontario and it has been already rewarded by the discovery of valuable ore deposits.

Jan 1, 1925

SME Membership Directory Listings of record March 31, 1072 SOCIETY OF MINING ENGINEERS OF AIME

Jan 7, 1972

By Lewis Carroll

AS he contemplates the numerous good things the hard-working committees have evolved for the 140th Meeting of the Institute, the Editor knows just how the walrus felt when he uttered his memorable, if somewhat lugubrious lines. For there are the Annual Reception and Dinner at the Commodore, 'the Gold Supply Symposium, the luncheons, general and special, and the Annual Institute of Metals Lecture, a Round Table on Iron Ore and a wonderful Informal Dance at the Grand Central Art, Gallery, substantial general sessions, a Smoker-and many other things. -Old, friends and new, reminiscences and confidential chats, horizons pushed back by new information and adjusted perspectives, courage revived and ambitions stimulated-one with a flair for the modernistic might make something-or nothing-of the kaleidoscopic preview 'of the coming Annual Meeting.

Jan 1, 1931

By D. N. Williams

THE present study was undertaken with two specific objectives: measurement of the thermal-expansion coefficient of ß titanium and examination of the effect of solid-solution alloying on the thermal expansion coefficient. Four titanium alloy niaterials were available in the form of annealed 5/8-in. diam rod. Three of these, Ti-8V, Ti-20V, and Ti-6A1-4V, were prepared in the laboratory from 140 Bhn sponge. The

Jan 1, 1962

By W. A. Forbes

OUR present-day geological surveys show that 36 of our States are underlain with bituminous coal, covering a total area of 496,709 square miles. The North American continent possesses 69 per cent of the world's coal reserves, with the United States alone having an estimated 55 per cent. The American coal reserves, in tons, are calculated to he about 3,500,000,000,000 tons, of which we have exhausted about 1 to 1 1/2 per cent. If this coal were mined at the rate of the 1918 production-a record output of 579;000,000 tons-it would not be depleted for 4,000 years. The more easily accessible and high-grade coals would obviously be consumed much before this; some estimates are 100 years. The natural progress of the nation's industries up to 1910 encouraged on every hand the development of new mines, especially where cheap and easy access to coal measures was coupled with short hauls to the consumer. Over-development resulted, which is perhaps today one of the fundamental causes for the many difficulties faced by the coal industry, which is highly competitive; about 70 per cent of the production cost is labor. Salient statistics for 1930, recently issued by the U. S. Bureau of Mines, follow:

Jan 1, 1932

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By G. Caetani, E. Burt

Jan 1, 1907

By P. Greenfield, P. A. Beck

RECENT work by J. Darby, Jr. in this laboratory has shown that the reported vanadium-rich limit of the s phase in the Co-V system at 1200°C is in error. The appearance of a second phase in s actually is restricted to alloys containing over 68 atomic pct V. The error in the original value is due apparently to a reaction that takes place along the numerous cracks in the s specimens between the alloy and the impurities present in the He + 8 pct H atmosphere in the annealing furnace. Such a reaction and the consequent appearance of a second phase can be suppressed if the alloys are sealed under vacuum in Vycor tubing. The new value of 68 atomic pct V for the vana-dium-rich limit of the s phase in the Co-V system effects slightly the s compositions calculated from average values of N, and N,. for various s phases. The standard deviation between experimental mean compositions and those calculated from the assumption that s is characterized by a constant number of 3d + 4s electrons per atom (N,), is slightly reduced from 9.1 to 8.8 pct. The maximum divergence for the V-Mn s phase is reduced from 15.5 to 14 atomic pct. The standard deviation calculated from constant electron vacancy numbers given by N.. = 4.66 (Mo + Cr + V) + 3.2 (Mn) + 2.2(Fe) + 1.71(Co) + 1.6(Ni) is now greatly reduced, as the maximum divergence for this correlation previously occurred in the V-Co system. This maximum divergence is reduced from 7.6 to 2.3 pct, and the standard deviation for all s- phases is reduced from 4.1 to only 2.9 pct. The correlation for electron vacancy numbers given by N. 5.66 (V when with Ni or Co) + 4.88 (V when with Mn or Fe) + 4.66 (Cr + Mn) + 3.3 (Mn) + 2.66 (Fe) + 1.71 (Co) + 0.61 (Ni) is made slightly worse, and the standard deviation increases from 2.8 to 3.9 pct. These changes, however, do not affect the conclusions of the paper.' The deviation between calculated and experimental s compositions is much less for either one of the electron vacancy correlations than for the correlation with the number of 3d + 4s electrons.

Jan 1, 1955

By G. G. Brown

Enthalpy-entropy diagrams are presented for natural gases of 0.6, 0.7, 0.8, 0.9, and 1.0 gravity over the pressure range of 5 to 10,000 Ib. per sq. in. and temperature range of 32º to 700°F. The charts indicate directly the work requirement and temperature rise for adiabatic compression or temperature change for free emansion of natural eases. Computation and Uses of Charts The Mollier diagram (Fig. 4), in which the enthalpy (heat content) is plotted against the entropy with lines of constant temperature, pressure,, and in some cases volume, has been found most convenient when dealing with the compression, expansion, and flow of fluids. In dealing with the flow of fluids, the sum of the increase in the enthalpy, AH, plus the increase in kinetic energy, AM —, plus the increase in potential energy, ?MZ, representing the total increase in energy of the fluid in flow, is equal to the sum of the heat q, and work added, —w, to the fluid while flowing between the entrance and exit of the flow system. AH + AM— + ?MZ = q-w [1] In cases where there is no significant change in potential energy or in kinetic energy (velocity), it follows that the increase in enthalpy is equal to the total energy supplied to the fluid. Under such conditions' the changes in the property of the fluid as it flows through a throttling valve, choke, or any other similar arrangement, may be read directly from the enthalpy-entropy diagram by following a horizolltal line between the known pressures' When compressing Or expanding a gas by means of a Or or engine in which no heat is added to or subtracted from the gas, but only work done, the changes in the properties of the gas may be determined along a vertical line of constant entropy between the entering and exit pressures. The power required for the compression of the gas may be readily determined by converting the increase in enthalpy into the desired units. The enthalpy-entropy diagram for natural gases is to the gas engineer what the steam diagram is to the steam-power engineer. For this reason it would be extremely convenient if a reasonably satisfactory enthalpy-entropy diagram could be prepared as a function of the gravity of the gas. A careful study of the known properties of natural gas indicate that this is possible. The effect of temperature upon the enthalpy at constant pressure is expressed as the "heat capacity" or "specific heat" of the gas. The best available data for natural and petroleum refinery gases indicates the relationship shown in Fig. I. From this it is clear that the specific heat of natural gases is a function only of the gas gravity and the temperature at atmospheric pressure. The effect of pressure on the enthalpy of natural gases is dependent upon the pressure-volume-temperature relationships,

Jan 1, 1945

By Reynold Q. Shotts

Data are presented which show that fractions of varying densities-from the same coals are oxidized at different rates by nitric acid. From oxidation data, the approximate quantity of "bright" and "dull" components may be calculated. Definite relationships between oxidation rate and rank are shown for density fractions from at least two bituminous coals.

Jan 1, 1950

By H. H. Campbell

The following paper deals almost exclusively with the results of practice at the works of the Pennsylvania Steel Company at Steelton, Pa. From the records of the furnaces at this plant, both acid and basic, large and small, are drawn the data for the various demon strations, and on a long and intimate experience with their opera tions are founded many theories and generalizations. It may seem that universal laws should not be built upon a basis so restricted ; but in reality the condition is the strongest guarantee of validity. Each table investigates some- certain variable, and by virtue of the common origin of the factors, we have good ground for assuming the corresponding agents to be equal. The examples may or may not be instances of good practice, and may be open to criticism if regarded solely as exponents of • metallurgical success. But it must be remembered that the lists are not made up of selected specimens, nor are they chosen to show su perior results; they are gathered to investigate, by strict scientific methods, the formula? of the operation. In such work no untoward results should be eliminated, save those which bear upon their face the stamp of experimental error. If the worst members be omitted, then the best must also be omitted. Only by using every available case can an honest attempt be made to deduce a true average. It is recog nized, however, that with the most careful selection it is difficult, if not impossible, to collect data representing universal conditions. In each table the records tell of a special practice, and all conclusions drawn from them are true only within the limits between which the equations have been integrated. Not assuming the prerogative of speaking for American melters in all the opinions herein expressed, nor acting as a camera in por traying an ephemeral state of national metallurgical development,

Jan 1, 1894