Search Documents

By Mariano de Córdova

In this paper, the coke oven life prolongation technology is reviewed from different points of view: blend design; battery heating; operational control; refractory maintenance. A summary of major inspections in critical areas, for the evaluation of the battery conservation situation is presented. A discussion on tools for the diagnostics of the degree of damage is carried out.

Aug 16, 2017

By Martim Hideki Nakayama Kurauchi

One of the main issues regarding the use of charcoal in metallurgical processes is its mechanical strength, which is much lower than coke. There is no defined standard to determine charcoal compression strength, and the methods described in the literature consist in using a prepared specimen and applying compressing load in the same direction of the charcoal fibres. As charcoal is highly anisotropic, it is proposed a procedure that does not use a specimen and with load applied on a specific direction. Instead, it intends to simulate industrial conditions by randomly dumping charcoal inside a tube, without preferential directional arrangement. This is an attempt to determine charcoal mechanical strength and predict the behaviour of bulk charcoal under a static load, as in a blast furnace. Experiments with controlled loads have been carried out on randomly distributed bulk charcoal with controlled initial size and their effect on the size distribution has been analysed. After compression, charcoal is screened and each size is weighed, determining the particle size distribution of the experiment. This method can therefore be used to evaluate charcoal mechanical strength.

Aug 1, 2018

By Joachiim Lehner

The application of post-combustion (secondary oxygen) to avoid skull formation on BOF lances was tested in industrial trials. The main findings are that no negative impact on the metallurgical targets (i.e. carbon, temperature and phosphorus at end of blow as well as iron–oxide in the slag) could be observed. The technology is capable of avoiding the buildup of lance skull and consequently increasing the average life of lance tips. The application of post-combustion not only affects the skull formation, there are also interactions with the refractory lining, especially thermal wear, and the utilization of the process gases (CO Recovery) that have to be considered. Special attention has to be paid to the parameters determining the use of secondary oxygen because rather small changes can strongly affect the points mentioned above. Since August 2016, the PCD (Post-CombustionDistributor) lances are used on a daily basis in the steelplant LD3 in Linz.

Oct 30, 2017

By Haruki Inami, Takashi Ishida, Kazuhiro Ohara, Hiroyuki Imanari

The highly competitive business environment of the international metals industry is driving demand for more cost-effective operation of steel making facilities, rolling mills, and strip processing lines. Achieving stable operation is vital if the steel industry is to produce high-quality products constantly and productively. In recent years, advances in computer processing speeds, data acquisition rates, and data storage capacity have rapidly led to greater use of the new technologies of big data, analytics, the IoT, and AI by control system designers and process engineers, and the introduction of industrial applications. The “Smart Rolling Mill” solutions for hot strip mills have been developed by our group with the goal of achieving sophisticated, state of the art, and automated operation in steel rolling mills. The various solution engines improve process stability, increase the performance of mill equipment, and provide improved process control. These solution engines are based on extensive knowledge of the rolling process and the associated control systems. Two solution engines in particular are the diagnosis systems for rolling condition and for product quality that contribute to cost-effective operation and lower yield loss. This paper focuses on the diagnosis systems for rolling condition and for product quality in hot strip mills. Advanced information technologies using big data analytics and machine learning are applied to real-time data collected from the automation system that controls operation and the rolling process. We have developed diagnosis solutions for rolling condition and product quality utilizing predictive and clustering diagnosis. Predictive diagnosis prevents serious problems by detecting changes in the state of the plant or in the rolling condition. Clustering diagnosis classifies patterns of fluctuation in product quality trend charts, providing effective tuning guidance for improving product quality. This paper describes these applications with several examples.

Oct 1, 2019

By Henrique Lacerda Eleutério, Aldo Henrique de Almeida Barbosa, Vicente Tadeu Lopes Buono

The automotive industry’s interest in galvannealed (GA) boron steel for hot forming processes application has been steadily increasing due to its excellent surface quality, galvanic protection provided to the parts, good paint adhesion and better weldability in relation to other coatings for this application. In this study, samples of 22MnB5 galvannealed steel were heat treated and hot stamped on a water cooled die in laboratory scale. The influence of heat treatment on stability of coating and steel was assessed by using initial heating rates 11.0ºC/s and 15.0ºC/s. Microstructural evolution of galvannealed coating and structural integrity of steel during hot forming were investigated by scanning electron microscopy with energy dispersive spectroscopy analysis (SEM/EDS/Line scan), X-ray diffraction (XRD) and optical microscopy (OM). It was possible to quantify the Fe-Zn phase evolution during hot forming, to understand the effect of these heating rates on the product properties and to establish an optimized heat treatment for hot forming of these steel. The heat treatment with the heating rate of 15.0ºC/s presented greater operational flexibility and final products free from surface defects or cracks in the substrate.

Oct 1, 2019

By Nigel Marx

In order to understand (and ultimately to predict) the friction reduction resulting from the use of polymer solutions, the rheological properties of model polymer solutions have been measured over a wide range of shear rates. Both temporary and permanent shear thinning have been observed. By using base fluids of different viscosities it has been shown that permanent shear thinning depends more closely on the shear stress experienced by the fluid than on the strain rate. Hydrodynamic measurements have been made on the polymer solutions using a compliant ball on flat lubricated contact that operates in isoviscous-elastic conditions. The measured friction values can only be predicted with reasonable accuracy if the measured shear thinning properties of the lubricant are taken into account in the hydrodynamic model.

Jul 31, 2018

By Alessandro Marques

Based on a short overview regarding steel defects in the final product, several refractory approaches to maintain or increase steel cleanliness are reviewed in this publication. By applying a ladle to mold approach, one potential to maintain cleanliness is to reduce the probability of air ingress by selection of a suitable slide gate system. Following this path, also the influence of a special configured impact pot is presented to maintain steel quality. Finally, higher productivity as well as cleanliness can be provided by selection of PROIL as a revolutionary product at the casting machine.

Oct 30, 2017

By Patrícia Mundim Campos Faria

The process of particle size reduction by grinding is inherently inefficient and involves high capital and operating costs. In particular, ball milling is one of the important unit operations in the iron ore pelletizing process. The mill product, due to its physical properties, determines the efficiency of subsequent stages of classification, filtration and pelletizing, thus impacting the quality of iron ore pellets. The work demonstrates the application of the population balance model in the optimization of a full-scale ball mil circuit grinding pellet fines with the aim to evaluate the optimal solids concentration to improve iron ore pellet quality. Initially, detailed experimentation was carried out in a 25.4 cm diameter batch mill and a relationship for mill scale-up using a linear population balance model in wet grinding systems was established. The selection and breakage parameters and the specific selection functions were determined for pellet feed iron ore. It was possible to identify the non-normalizable nature of the breakage functions of the ore studied, which were modeled properly. Afterwards, as a result of incorporating the specific selection functions and breakage functions into the linear population balance model, it was possible to predict product size distributions in the pilot and plant scale mills (0.416 and 5.18 m diameter, respectively) from data obtained in the 25.4 cm diameter mill. Finally, with this scale-up procedure it was possible to appraise the plant scale optimization via laboratory scale grinding mill tests. The effects of changing percent solids were assessed in order to improve the industrial mill performance and the optimal value should be in the range from 76 to 80%.

Aug 1, 2018

By Hugo M. Checo

Friction-reducing textures for lubricated mechanisms have received much attention since the advent of microtexturing techniques. In this work we consider the piston ring/liner contact, numerically simulating the rings as they slide against a textured liner. This situation has not been sufficiently analyzed because its numerical complexity is much greater than that of texturing the rings. Further, we consider the actual typical geometries of oil-control, wiper and compression rings, under realistic loads and velocities. The results show the possibility of friction reduction when the texture on the liner is properly designed, identifying starvation alleviation as a crucial intervening mechanism.

Jul 31, 2018

By Massimilinao Svetina

In 2010 Danieli & C. S.p.A. put into operation a new Pickling Tandem Mill in Cremona (Italy) at Acciaieria Arvedi, the last Pickling line coupled Tandem Cold Mill (PLTCM) in Europe. The plant was tailor-made to suit the specific requirements of this customer; a very broad range of sizes and grades (IF to AHSS as well as DP and TRIP1000) including ultra-thin hot band can be processed, achieving a total capacity of 1.6 Mt/y. The Danieli & C. S.p.A. Turboflo® process was selected because of its proven efficiency and ability to handle ultra-thin gauges at speeds exceeding 400 mpm in the pickling tanks. All the equipment, i.e. pickling section and rolling mills was provided with the last generation of Danieli market-oriented technologies. Danieli & C. S.p.A. - with the support of Arvedi and feedback from the field - is continuously improving its technical design solutions and optimizing plant operations.

Aug 16, 2017

By Paolo Demetlika

In this paper it is shown how the “Zero Operator” concept on the casting floor has been reached by adoption of a standard 6 axis industrial anthropomorphic robot coupled with the most innovative machine vision technology. This has been achieved by automating all the operations related to the ladle and tundish activities, including shroud manipulation, powder addition, ladle nozzle identification, nozzle opening by lancing, temperature measurement and chemical sampling. Q–Robot CAST family products are the result of the successful alliance between industrial robotics and the most advanced technology in process automation. This led, for each production area, to the introduction of flexible automation in dangerous places, even where some degree of human intervention is still necessary. By using anthropomorphic robots, human operators can be reassigned to safer environments. Furthermore, robots are suited to deal with repetitive and labor intensive tasks thus guaranteeing a high process quality.

Oct 30, 2017

By Sandra Lúcia de Moraes

Vários trabalhos voltados a resolução dos problemas da utilização de bentonita no processo de aglomeração de minério de ferro referem-se ao emprego de aglomerantes orgânicos, sendo que os dois tipos principais são os à base de celulose e de poliacrilamidas. Este trabalho teve como objetivo um melhor entendimento da ação de um aglomerante à base de carboximetilcelulose no ganho de resistência mecânica da pelota. Foi avaliada a interação entre a superfície mineral de dois concentrados tipo pellet feed brasileiros e os componentes presentes no aglomerante Peridur de uso comercial. O método proposto e desenvolvido no presente trabalho permitiu comprovar que um mesmo aglomerante atua de maneira diferenciada dependendo do tipo de minério de ferro empregado. Isto reforça a importância do entendimento de como cada produto, utilizado como aglomerante no processo de pelotização, age nos constituintes do minério de ferro para promover o incremento necessário de resistência mecânica das pelotas.

Aug 16, 2017

By Clara Lana Bispo Fidelis

Nos últimos anos, um grande destaque na área dos biomateriais tem sido dado aos compósitos produzidos a partir de fosfatos de cálcio e biomateriais poliméricos, uma vez que podem ser empregados eficazmente em substituições do sistema ósseo e cartilaginoso. Este trabalho teve por objetivo desenvolver filmes poliméricos a partir de blendas entre dois polímeros biodegradáveis: o PLGA e o PHB, associadas ao BCP na forma de material particulado. Foram produzidas e caracterizadas duas formulações, 50/50 e 70/30 de PLGA e PHB, respectivamente. Em cada formulação dessas blendas foram introduzidas 10% e 25% de BCP, em relação à massa da matriz polimérica. Os compósitos foram processados pelo método Casting, sendo obtidos os compósitos pela evaporação do solvente utilizado - clorofórmio. É possível observar pela microscopia eletrônica (MEV) que as partículas de BCP formam uma fase dispersa em torno da matriz polimérica. A combinação destes materiais promoveu uma melhoria na performance mecânica dos compósitos. A conjugação de polímeros e biocerâmicas garantem elasticidade associada ao material polimérico, enquanto o BCP promove o aumento da rigidez e resistência à tração. Análises físico-químicas (DSC e DRX) demonstram a possibilidade de existir uma interface difusa entre os polímeros e a biocerâmica. Estes filmes parecem apresentar grande potencial para obtenção de biomateriais para substituições osteocondreais e/ou como membranas reabsorvíveis do periósteo.

Aug 8, 2018

By Edson José Costa Santos

Uma fonte promissora de pós-descarga é a obtida por cátodo oco, isso devido a sua operação, baixo custo, elevada densidade de espécies ativas e design. Neste trabalho empregou-se a espectroscopia de emissão para diagnosticar as espécies ativas produzidas descarga em catodo oco. Variou-se a corrente elétrica na descarga de Ar entre 150 e 600 mA para verificar a influência da corrente na descarga. Posteriormente, fixou-se a corrente elétrica e variou-se o fluxo de N2 na pós-descarga de 1 a 6 cm3/min. Observou-se que a corrente elétrica influenciou na intensidade de emissão das espécies produzidas pelo sistema de descarga cátodo oco. Além disso, não foi observada a emissão ótica da espécie de ? 2 N na pós-descarga Ar-N2.

Aug 7, 2018

By Johne Jesus Mol Peixoto, Itavahn Alves da Silva, Marina Braga Campos, Carlos Antônio da Silva

A composição, morfologia e distribuição de tamanho das inclusões presentes nos aços têm forte influência sobre propriedades químicas e físicas como fadiga, usinabilidade e resistência à corrosão. Desta forma, melhorar a qualidade do aço implica em aumentar a limpidez do aço líquido [1]. Para tanto são utilizados processos (que apresentam diferentes custos operacionais) como o burbulhamento de gás inerte na panela e o tratamento no desgaseificador a vácuo RH. O presente trabalho apresenta resultados de simulações matemáticas bem como operacionais dos processos de remoção de inclusões através do borbulhamento de gás inerte e do tratamento a vácuo. É feita uma comparação entre as capacidades de remoção de inclusões destes processos, confirmando a maior efetividade do reator RH.

Oct 1, 2019

By Mariana Sizenando Lyrio, Weslley Luiz da Silva Assis, Harison da Silva Ventura, Gabriella Maria Silveira de Sá, Paulo Rangel Rios, Ana Gabriella Conceição dos Santos

A nucleação em contornos de grão é uma das mais importantes na maioria dos metais utilizados em engenharia. Um exemplo clássico é a nucleação de ferrita no contorno de grão austenítico, mas este tipo de nucleação também é predominante na recristalização. Nesse trabalho, simulações computacionais são realizadas de modo a estudar a transformação de fase nos contornos de grãos equiaxiais e nos contornos deformados. Os grãos equiaxiais são representados por poliedros de Poisson-Voronoi e os grãos deformados por elipsoides de diferentes razões de aspecto. Os resultados são comparados como os modelos analíticos de JMAK e CAHN. A microestrutura final não é visivelmente afetada pela razão de aspecto dos poliedros predecessores. Todavia a cinética de transformação dos grãos recristalizados é significativamente alterada.

Nov 9, 2019

By Masakazu Iida

In this article, technologies of unburned Al2O3-MgO (UAM) refractories are demonstrated in terms of microstructure evolution. During operation, Mg2+ diffuses from MgO to Al2O3 through the liquid phase to form spinel (MgAl2O4) network. Molten slag tends to penetrate along the voids in the spinel network structure and spinel dissolves in the penetrated slag. Therefore, maintaining a high degree of spinel saturation in the penetrated molten slag is important. In order to achieve the condition described above, suppression of overall mass transfer through penetrated slag is effective. This is achievable by evolution of complicated spinel network structure with small pore diameter, which increases the flow resistance of molten slag. Thus, optimization of refractory composition and fabricating conditions, with the aim of creating on improved spinel network, is essential. The effectiveness of spinel network improvement was validated by commercial applications. According to the investigation of UAM brick after use, further densification due to heating under restrained conditions was recognized. Hence, it was concluded that the evolution of the spinel network structure in UAM refractories is essential technology needed to improve durability.

Oct 30, 2017

By Daniele Tolazzi

In today’s highly competitive market situation, it is of outmost importance for EAF steel makers to optimise their processes in order to reduce operating costs and to improve safety and reliability of the equipment. The laser based off-gas analysis technology, With laser units installed on the fix duct, downstream the combustion gap, uses the “Tuneable Diode Laser Absorption Spectroscopy” (TDLAS). The system performs real-time off-gas emissions measurements of CO, CO2, O2, H2O and temperature. A closed-loop operation is in place for dynamic control of the chemical energy package combustion/post-combustion of CO, H2 and CH4 gases into the EAF furnace shell. A statistical framework which builds on a data analysis engine, based on Danieli Automation Q3Intelligence technology, evaluates the “fingerprint” of the process represented by average and deviation trends of both gases and other process parameters. Process fingerprinting is conceived both for offline profile optimisation and on-line control of the refining process. This paper describes how the technology has been applied and the results achieved at ACCIAIERIE BERTOLI SAFAU (Italy) 100 t AC Electric Arc Furnace.

Aug 16, 2017

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Pedro Jorge Walburga Keglevich de Buzin

The steel production in mini mills generates several process residues, among them the electric arc furnace dust (EAFD). This residue has as main elements Fe, O, and Zn, being classified as hazardous by the presence of Pb and Cd. In recent years, a rise in the chlorine content of this residue was observed, motivated by the increased use of scrap with impurities bearing this element. In this work, a qualitative assessment of the presence of chlorine in the electric steelmaking process is made. Complementing it, theoretical considerations based on the computational thermodynamics tool FactSage show the effects of the chlorine on the mineral species in EAFD and on gaseous species in the gas phase (HCl and Cl2). For this study, PVC polymer was used as the chlorine carrier substance which contaminates the EAF charge; presence of other minor elements in the system such as K, Na and Pb were also considered.

Aug 7, 2018