Search Documents

By S. Mundike

A scraper-based block cave method has been successfully applied to extract the Lower orebody at Nchanga since the 1950s. Since inception, scraper drifts and service ways have been supported using steel arch sets fabricated to a specific design from high strength manganese steel To reduce costs and to improve productivity, trials commenced in 2002 using fibre reinforced shotcrete as an alternative support method. One of the areas, the 2420 8E 1C trial drift, was subjected to abutment loading for several months prior to undercutting and cave mining. Shotcrete installed exhibited minor cracking shortly after application but very little deterioration thereafter. Following the success of the trial, the application of fibre-reinforced shotcrete was extended to other drifts. This paper describes the application of fibre-reinforced shotcreteat Nchanga and outlines design and quality assurance methods employed.

Jan 1, 2005

By W. H. Gauvin, N. J. Themelis

I N ADDITION to its practical importance in the beneficiation of iron ores and in direct-iron processes, the study of the reduction of iron oxides involves many aspects of challenging theoretical interest. The complexity of the reduction process combined with the fact that under different experimental conditions the controlling stage for the reaction may not necessarily be the same, has led experimenters in this field to a wide diversity of opinion regarding the reaction mecl1anism. As a rule, each investigation has been restricted to the study of one or two variables over a comparative]~• narrow range of experimental conditions, and consequently, it be-comes necessary to examine the significance of each published work in the light of the results of other experimenters in the field.

Jan 1, 1962

By C. R. McClung

"Molybdenum, in the form of molybdenite, is a common byproduct of many copper mining and concentrating operations. Contrary to most copper sulfide minerals where recovery is principally liberation controlled, the recovery of molybdenite is much more complex with fully liberated particles commonly lost to tailings. It is this complexity that facilitated the necessity for a geometallurgical investigation of molybdenite from the Bingham Canyon deposit. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes (i.e. morphology, angularity, liberation, size) have on the recovery of molybdenite in the processing circuit. A set of samples was collected from the ores and products produced by Rio Tinto Kennecott’s Copperton Concentrator. All samples were analyzed using normal polarized reflective light, Mineral Liberation Analyzer (MLA) and X-ray diffractometery (XRD) techniques. The results of this investigation revealed the presence of two distinctly different types of molybdenite, which have been identified as the two polytypes of molybdenite, i.e. hexagonal (2H) and rhombohedral (3R). The 2H polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the core of the Bingham Canyon deposit. The 3R polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance along the margins of the mineralized intrusive body or central core. Concerning their metallurgical behavior each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. For instance, the 2H polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This commonly results in the production of a high quality molybdenum concentrate under normal operating conditions common to most copper concentration operations. In contrast, the 3R polytype is difficult to grind and kinetically “slower” floating with surface attributes that less amenable to recovery under normal operating conditions. Therefore, in deposits with higher concentrations of the 3R polytype, modifications to the normal operating parameters may be necessary to improve the recovery of molybdenum. Finally, a preliminary investigation into the metal budget of porphyry Cu and Mo deposits indicates that a positive correlation may exist between the total economic metal budget and the polytype content. For example, higher concentrations of the 3R polytype appear to be more prevalent in Au-enriched porphyries versus Mo-enriched porphyries. This observation may also serve to help explain why it is easier to obtain high rates of recovery in Mo ± W-rich deposits, which contain little to none of the 3R-polytype. Consequently, the potential for the metal budget of a porphyry deposit to be used as an indication of the molybdenite polytype present, as well as its impact on the economics (exploration) and/or on the processing circuit (plant design) could exist. In conclusion, this investigation highlights the necessity of understanding the mineralogical properties or characteristics of molybdenite and/or other economic mineral(s), as these can and will have a direct impact upon the performance and plant optimization."

Jan 1, 2016

By Herbert Hoover

THE Federation of Engineering Societies has been created for the sole purpose of public service. This initial meeting surely warrants some discussion of a few of the problems to which this organization, for expression of the --. engineering mind, can quite well give consideration. Some of the greatest of the problems before the country and, in fact, before the world, are those growing out of our industrial development. The enormous industrial expansion of the last fifty' years has lifted the standard of living and comfort beyond any dream of our forefathers. Our economic system under which it has been accomplished has given stimulation to invention, to enterprise, to individual improvement of the highest order, yet it presents a series of human and social difficulties for the solution of which we are groping. The congestion of population is producing subnormal conditions of life. The vast repetitive operations are dulling the human mind. The intermittency bf employment due to the bad coordination of industry, the great waves of unemployment in the ebb and flow of economic tides, produce infinite wastes and great suffering. Our business enterprises have become so large and complex that the old personal relationship between employer and worker has to a great extent disappeared. The aggregation of great wealth, with its power of economic domination, presents social, economic ills which we are constantly struggling to remedy.

Jan 1, 1920

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Edward A. Barrett, Lynn L. Rethi

Recent studies have shown that miners performing construction, maintenance, and repair (CMR) work activities in the conduct of their jobs incur from 39 to 65 percent of all reported injuries in the mining industry, The number is particularly high at surface aggregate operations; however, the problem exists at all mining locations and commodities. To address this issue, an interactive, (3-D) slides training exercise, Hazard Recognition Training Program for Construction. Maintenance and Repair Activities, was developed. The purpose of the exercise is to teach work& to recognize CMR hazards in the workplace and to deal with them using accepted safe work procedures. It was field tested using a total of 340 persons from surface mining operations in six states. The subjects were tested before and after the training intervention to determine if objectives of the instruction were achieved. Results indicated that 7 1 percent of the participants showed improvement in ink test scores. Following the posttest, subjects responded to a seven question Likert scale. These questions related to the validity of the exercise and the utility of the training program. More than 93 percent of the miners reported that they "learned something new from the training" and over 94% said they "would use these practices to work more safely".

By C. Morel, P. Fredes, L. Rojas

This article presents a comprehensive study on the development and application of the specific module called "Exclusion Zone" created by Orica to determine blast evacuation exclusion zones. This module, integrated into the "SHOTPlus™ (blast design software)" software, has been used in the context of optimizing equipment evacuation exclusion zones in a northern Chile mine. The main objective has been to reduce the travel times of extraction equipment without compromising the safety of individuals. The module considers various factors such as the explosive charges used, stemming, sector topography, and detonation sequence to determine the rock projection generated by the blast. Furthermore, it utilizes information collected by drones and support tools such as Groundprobe and BlastVision™. The results obtained demonstrate that the use of this technology has allowed the optimization of blast evacuation distances in the northern Chile mine, generating significant economic benefits for the client.

Jan 1, 2024

By P Aspinall

Safe work Australia (SWA) has a number of proposed amendments to existing Workplace Exposure Standard (WES) values that may dramatically change how mining workplaces using personal gas monitoring instruments will operate. In consultation with leading gas monitor manufacturers and distributors, an assessment of common Australian alarm settings values and analysis of potential frequency of increased alarm likelihoods has been conducted. This assessment explores the relationships between current monitoring practices, using instruments as health and not just safety tools and identify what will be needed to minimise worker ‘alarm fatigue’ and for common tasks to continue safely. This paper provides the necessary information to aid industry and hygienists to be ‘future ready’ given the likely impact that order of magnitude reductions in time weighted average (TWA) values for NO2, SO2, H2S and other common gases will have on current working practices. Reductions to gas alarm values will provide significant challenges to existing work methods and will require, practical application of the pending future values. Improvements and awareness of instrument capabilities by safety and hygiene professionals will better utilise gas monitors real-time data monitoring capacity and no longer be just ‘safe or not-safe’ instruments. The presentation seeks to promote the practical steps required in setting alarms based on risk consequence and likelihood, increase general awareness of the tools and data available in modern instruments and will enable industry professionals to better manage the challenges of any potential future changes.

Apr 16, 2024

By E. M. Chance

HERBERT M. WILSON, Pittsburgh, Pa. (written discussion).-Permit me to endorse the author's conclusions and their form of presentation as ,being, in my judgment, the last word 'on the subject of lights for the illumination of coal mines. I also feel that the open-flame oil lamp has outlived its usefulness, and that it should go, in the interests not only of safety but of efficiency. Where an open-flame lamp can be used with safety in non-gaseous mines, the acetylene light adds materially to efficiency by its better illumination, and to safety for the numerous reasons given by Mr. Chance. The latter, however, lays chief stress on the value of the acetylene because of its non-fouling and non-obscuring effect on the atmosphere. Another important advantage over any other form of illumination is the clear, bright light projected at the point where the workman may look for danger. The better illumination materially safeguards the worker against obstacles over which he may stumble when traveling, and against dangers from falls of roof or of coal, weakness in timbering, and similar conditions. The acetylene lamp, where it may be used with safety, has advantages even over the present electric cap lamp, in that it gives a higher luminosity; and when the miner comes to learn its signals, as he will in time, just as he learns those given by the open-flame or the safety lamp, he will find that the acetylene lamp is a fair detector not only of methane but of carbon dioxide, as clearly shown by Mr. Chance. The only, serious objection, raised against the use of carbide lamps. has been recently in Pennsylvania, due to the belief of the State Mine Inspection Department that it endangered miners working on pillar work, or other places where carbon dioxide might accumulate, or where there is lack of sufficient ventilation, and because it was believed that the indications of the carbide lamp would not give the miner sufficient warning. On this point Mr. Chance has clearly shown the fallacies of the objections. I may add that for those unable to detect carbon dioxide with the acetylene lamp, the maximum of protection would be afforded by using an open oil lamp or a flame safety lamp in such places; or, because the miner might not watch his oil light, a better, protection still would be offered by a sufficient number of daily inspections of such working places by a fire boss or other official, with flame safety lamp.

Jan 4, 1917

By Herbert H. Einstein

Swelling ground is one of the most feared problem in tunneling. Although usually not causing sudden failures during construction, the very large and long- lasting deformations give contractors and designers the impression of facing an inevitable phenomenon against which there is no technical defense. Examples are concrete liners of up to 1 m that have been cracked or crushed, tunnel inverts that are heaving at a rate of 0.1 m per week during construction and continue to heave during decades. This author (Einstein (1979). Einstein et al. (1972) (1975)) and others (Huller (19761, Grob (1972) (1976). Golta (1967), tienke (19761, Krause (1976). Lee et al. (1976)) have described many cases of swelling tunnels that illustrate the significance and magnitude of the problem. This paper intends to show that tunnels in swelling rock can be built to perform satisfactorily. . For this purpose the tunnel builder needs to know how to determine the existence and specific behavior of swelling ground, how to select appropriate structural characteristics of the tunnel and predict its performance under the specific ground conditions, and finally how to construct the tunnel such that the anticipated performance will be achieved. This concept of a design-construction procedure is the same as that for tunneling in general; it is mentioned here for NO reasons: 1. To point out that design and construction cannot and should not be separated. The way in which the tunnel will be built has to be an integral part of the design. 2. This paper will be structured corresponding to the procedural concept.

Jan 1, 1981

By J. E. Nesset, F. Rosenblum, J. A. Finch

"The self-heating of sulphides can be a major hazard in mining operations and concentrate handling, particularly during transportation and associated storage. Self-heating results from the oxidation of sulphide minerals and can vary from being insignificant to highly reactive and potentially hazardous to both humans and infrastructure. It is essential that there be a reliable test methodology that can measure and categorize a given sulphide material as to its self-heating potential. By their nature, sulphide ores and concentrates are complex and variable mineral mixtures making it difficult to predict their self-heating behaviour a-priori based on mineralogy or with a simple “snapshot” test. Furthermore, self-heating behaviour will depend on the state of oxidation of the sulphides as well as time, temperature and humidity. A review of available testing apparatuses and protocols that can be used to assess self-heating potential is presented. Each of these methodologies was examined in relation to its ability to measure and reliably predict the latent self-heating hazard of a sulphide material. Several of the methods were tested and compared to illustrate their strengths and weakness. The results indicated that a number of the test protocols may produce false negative indications of self-heating potential, constituting an obvious concern to the industry.INTRODUCTION Sulphides as well as other materials (coal, wood chips, hay, powdered milk, to name a few) that are stockpiled in an air atmosphere may undergo oxidation reactions which can result in the evolution of heat (Beever, 1984) (Hudak, 2002) (Blanchard, 2007). If the rate of heat generated exceeds the rate of heat dissipation, the stockpile temperature will rise, potentially leading to “hot spots” in the most reactive areas, and possibly even fires. The heat generation rate, the “self-heating” rate, depends on many factors such as the type and composition of material, particle size, moisture content, oxygen availability, ambient temperature and humidity, and of prime importance, the extend of prior oxidation, or more specifically, the presence of oxidation products. The desire of operators that mine, process or transport sulphide-bearing materials with a potential for self-heating is to have an accepted and reliable method for evaluating and quantifying the potential hazard of their material. The challenges are how to best measure the self-heating properties of given samples, and based on results, predict the behaviour of the bulk material over time and in-situ. Generally, when evaluating a given material one derives the self-heating characteristics of that sample at the time and under the conditions of testing, which will be referred to as a “snapshot test”. If that material is invariable, i.e. it will not change its response over time, then it may be considered to be a “predictive test”. However, if as a result of continuing oxidation or other changes, the material becomes more or less reactive with time, then a “snapshot test” is unreliable with respect to predictive ability."

Jan 1, 2014

By D. Campbell Mackenzie

THIS paper is submitted primarily to put on record the results of a number of experiments carried out at the Wingdam mine of Consolidated Gold Alluvials of B.C., Ltd., with the object of establishing a reliable method of concentration of 'wash' and a maximum recovery of gold from the concentrate. It will be generally admitted that, during the last two decades, a tremendous amount of research work has been carried out, both by private companies and Government departments, with a view to improving the technique of the recovery of gold .from quartz veins or lodes. So thorough have been these investigations that milling practice at a modern quartz gold mine is almost an exact science, carried out with meticulous accuracy. In placer mining, on the other hand, very little departure from old traditional methods can be noted, with the exception perhaps of the more modern gold dredges. This may be due to the fact that the concentration of placer gravels, up to a certain point, is comparatively easy. Only a simple equipment of sluice box and riffies seems necessary where the gold is coarse and the gravel free from clay. In the early days of placer mining, when claims were rich and fairly 5hallow, nobody worried very much about fine gold; and, if clay was present, an enlarged dump box was constructed in which the gravel was subjected to a rather desultory puddling. That large quantities of gold are lost in normal placer practice is generally admitted. Some 26 years ago, I had inspectorial charge of many bucket dredges on the Ovens river, in Australia. Occasionally it was necessary for a dredge to work through its own tailing to reach a new section, and almost without exception enough gold was recovered from these tailings to defray the total cost of moving the dredge. Since those days, the technique of gold recovery in dredging has been considerably improved and it is still receiving close attention. Outside of dredge mining, most placer operations, deep or otherwise, are as they were-notorious gold losers, paying little attention to the recovery of fine gold and taking an absurd amount of time over each clean-up. In the Cariboo district of British Columbia, the alluvial gold is usual y associated with varying quantities of black sand (magnetic) and grey sand (non-magnetic); and it can be taken as axiomatic that, if you save all the black sand and grey sand, you save practically all the gold. It is on this hypothesis that we have carried out our research work and brought our recovery system up to its present highly satisfactory standard.

Jan 1, 1937

Professor Skeats said: I wish at the ,outset to express my appreciation of the h0!-l0ur conferred on me by my election as President of this Institute for the ensuing year. The selection of a geologist for this position by a body of mining engineers andmetallurgists may be taken as an indication of the recognition that the subject is one which may play a useful part in the great metal industry. Among the records of primitive man the finding of implements of bronze and of iron indicated one of the important, advances made in human civilization, and shows that...

Jan 1, 1924

The commercial application of electrolysis to zinc sulphate solutions for the production of metallic zinc is a development ·of the past twenty years. Earlier attempts failed to give satisfactory results, chiefly because certain harmful elements were either not recognised as being present in the solution, or, if recognised, suitable methods of removal had not been developed. The electrodeposition of zinc from zinc sulphate solution is extremely sensitive to the influence of a great many factors, all of which appear to be closely inter-related.Some of these factors tend to minimise the necessity for a high degree of purity of the solution, while other factors aggravate the harmful nature of certain impurities.The relationship existing betweBn the various factors in zinc electrolysis makes a general discussion of the injurious effect of impurities very difficult since, under one set of conditions a given concentration of an impurity may be of minor: importance, where its under another set of conditions the same concentration of that impurity may prove dangerous to successful electrolysis.

Jan 1, 1934

By Marcos Villegas

El presente texto describe el desarrollo del sistema de gestión de riesgos en la reingeniería de procesos, justificando la inversión en gestión de riesgos de la concentradora Atacocha donde se protege a las personas, activos e ingresos, minimizando el potencial de pérdida de los riesgos y así proveer fondos para recuperar las posibles perdidas y soportar el sistema en salud, seguridad, medio ambiente y Calidad (SSMAC).

Sep 9, 2007

By Reno H. Sales

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

By Sales, Reno

Since leaving school my efforts have been geared to the task of making geology useful to the mining industry. The responsibility of the economic geologist or mining geologist of today has grown to be more, than that of merely finding a faulted segment of a vein. The very life of our mining industry is at stake. The tremendous progress in every branch of our modern civilization has been made possible through the developments in the use of metals. Many of our great industries, including that amazing field of aircraft production live and thrive only because of metals.

Jan 1, 1942

The objectives of this research were to examine and to laboratory performance of several brands of rigid urethane een brands, produced by 13 manufacturers, were examined. was performed in a laboratory under controlled conditions. document the foam. Eight-All testing Preliminary laboratory tests included flame spread evaluations, flame penetration, ignition temperatures, air permeability, and adhesion. Having established arbitrary cutoff values, the original 18 candidates were narrowed to 8. More specialized tests followed. The effects of water immersion and dry aging on flame spread performance and other physical properties were then examined. This Bureau of Mines report was written to provide information for those concerned with using rigid urethane foam as a sealant. Its intent is to describe the various laboratory evaluations performed and to delineate the performance of each candidate. This report neither promotes nor discourages the use of rigid urethane foams. It presents results that will enable those responsible for using or enforcing the use of rigid urethane foams in underground mines to make informed decisions.

Jan 1, 1985

By Debasis Deb

The first version of the longwall strata control and maintenance system (LSCMS) has been successfully developed by the Strata Control Re¬search Team at the University of Alabama. The system includes a software package designed to monitor shield leg pressure, interpret the data and predict the forthcoming roof loads and the existence of geological anomalies. It can also detect maintenance problems of the face equipment. The LSCMS was installed underground and connected to the surface terminals at Drummond's Shoal Creek Mine in Alabama. The system has proven to be a useful and practical system for improving safety and efficiency in coal-mining operation. The Shoal Creek Mine is a new, large coal mine operated by Drummond with two longwall panels. The Blue Creek seam is the primary source of coal production. It is located at a depth of 275 to 440 m (900 to 1,450 ft) below the surface with an approximate 2% southwest dip. Typical strata conditions are represented by two stratigraphic columns (Figs. la and b). A fireclay/dark shale parting (called Middleman) 0.2- 0.7-m- (1- to 2.5-ft-) thick exists between the Mary Lee and Blue Creek seams. Mining conditions vary from area to area. This mainly depends on the Blue Creek seam thickness that ranges from 0.9 to 2.9 m (3 to 9.5 ft). The thickness of the Mary Lee and the parting is relatively consistent with a to¬tal of 0.9 m (3 ft). They are mined when the Blue Creek seam becomes thinner. In most of the panels, the immediate roof is composed of sandy shale 1.5-

Jan 1, 1997

By M. Mostert

Mining companies sponsor a range of non-core, corporate social responsibility projects to adhere to social and labour plans and environmental management prerequisites that form part of a mining licence application. Some companies go above and beyond such projects, sponsoring initiatives that generate renewable energy through solar power, wind energy, natural gas, etc. The challenge for these companies is to choose between a variety of projects to ensure maximum value, especially in times when the economic climate might be less favourable for such projects. The focus of this research was to analyse the concept of sustainability as it exists today, and to apply that to the triple bottom line accounting method in an attempt to quantify the sustainability of a project. Research was done on the methane burn-off project at Sibanye Gold?s Beatrix Mine to establish how such projects are planned and financed, and what impact they have on the triple bottom line of a company. The financial bottom line is, by definition, one that executives understand. This paper also proposes a quantitative method for defining the social and environmental bottom lines as well. By considering the financial, social, and environmental values, the study attempts to determine a monetary value for a sustainable renewable energy project. This monetary value can be compared to similar values obtained for other sustainable renewable energy projects under consideration. The research suggests that monetary value alone is not enough to base a sustainable decision on, and qualitative measures are suggested for use in conjunction with quantitative methods. The selection method proposed should assist the board of a mining company to choose the most sustainable option and the project that will add the greatest value to the company across all three bottom lines. It will also provide increased justification for such renewable energy projects, even in periods of harsh or uncertain economic climates.

Jan 1, 2014