Search Documents

By Mehmet Ali Recai Önal, MAHMUT CAMALAN

Mineral liberation is one of the primary objectives in comminution circuits for the downstream separation of valuable minerals. Breaking minerals through their grain boundaries (grain-boundary breakage) enables mineral liberation in their natural grain size, removing the need for intensive grinding. This study aimed to evaluate if gaseous carbon dioxide, oxygen, or hydrogen can be used as grinding additives to promote the liberation of chromite grains by grain-boundary breakage. For this purpose, chromite ore particles in the −9.53 + 6.35 mm size fraction were pretreated by exposing them to carbon dioxide, oxygen, or hydrogen flow. Then, the untreated and pretreated samples were broken in a drop-weight tester under the same conditions. Finally, the graderecovery plots of chromite grains in the selected progeny size fractions and the overall progeny distributions were measured and compared. Pretreatment with carbon dioxide flow was found beneficial for grain-boundary breakage. It significantly enhanced the liberation of coarse chromite grains along with the overall progeny fineness. EPMAanalysis showed that the adsorption of carbon dioxide seems to reduce aluminum concentration at grain boundaries, which could be the reason for grain-boundary weakening. These results suggest that carbon dioxide can be used as a grinding additive, reducing the carbon footprint of the mining industry.

Oct 29, 2020

By MATTHEW HART, THOMAS BAMFORD, Kamran Esmaeili, MICHAL KOWALCZYK, FILIP MEDINAC

Improved haul road conditions can positively impact mine operations resulting in increased safety, productivity gains, increased tire life, and lower maintenance costs. For these reasons, a monitoring program is required to ensure the operational efficiency of the haul roads. Currently, at Bald Mountain mine, monthly site severity studies, ad hoc inspections by frontline supervisors, or operator feedback reporting is used to assess road conditions. These methods are subjective and provide low temporal resolution data. This case study presents novel unmanned aerial vehicle (UAV) technologies, applied on a critical section of haul road at Bald Mountain, to showcase the potential for monitoring haul roads. The results show that orthophotos and digital elevation models can be used to assess the road smoothness condition and to check the road design compliance. Moreover, the aerial mapping allows detection of surface water, rock spillage, and potholes on the road that can be quickly repaired/removed by the dedicated road maintenance team.

Sep 15, 2020

By P. Mühlen, C. Nelson

Process control optimisation depends a lot on the availability of timely data from production to give operators a chance to make adjustments before potential process upsets or disruptions happen. A lot of data is already available with newer and updated machine technologies, but what about the process upsets coming from the raw materials that we use? They are natural products and therefore they are not of a stable composition or mineralogy. The production process depends on a certain chemical or mineralogical stability of the raw materials when they come to a roaster, kiln or sintering stage. Only then can the proposed reactions take place and the equipment be operated at stable temperatures. Laboratory analytical technologies have the limitation that they depend on representative samples and have a long time delay. Therefore online (real time) analysers are used nowadays in mining applications to obtain an early indication of the actual mined or to-be-processed ore. Most available technologies can only analyse inorganic content on an oxide or elemental level. Near infrared (NIR)- based online analysers can overcome that limitation and give a real time analysis of organic as well as inorganic composition, if required on a mineral level. The paper will present two case studies where the NIR online technology was successfully adapted.: a) Optimising refractory gold ore processing at the Goldstrike roaster operation b) Optimising the sinter process at a Japanese manufacturer. Keywords: Analyser, NIR, online, realtime, gold, roaster, iron ore, sinter, mineral phase analysis

Jan 1, 2020

By David Whalen

Mobile equipment in oil sand mining operations experience more maintenance problems than similar equipment in other surface mines, due to soft underfoot conditions. Oil sand properties are known to vary with temperature, bitumen content and previous loading cycles. One of the challenges is the widely variable underfoot pressure which supports shovels and trucks. In the case of a heavy hauler driving on in-pit roads, each tire is supported by a different ground stiffness resulting in an apparent uneven surface. Driving over uneven ground causes twist in the truck frame, which is transmitted to the dump body. Through a finite element analysis of a haul truck dump body, it was shown that slight frame twists produce localized stresses in the intersections of the floor stiffeners. These stresses are at times greater than those resulting from the maximum ore weight and are primarily responsible for cracking in these intersections. Syncrude maintains high quality haul roads, which are constructed of gravel, and makes every effort to keep the shovel pit roads as smooth as possible. This problem cannot be avoided through operational practices only and must also be accounted for in the design of haul truck bodies.

May 1, 2003

By McKenzie A. M

The Corridor ore body is so named because it occurs in an east-west zone or corridor of schist bounded on the north by the siliceous conglomerates of Mount Lyell, and on the south by similar conglomerates of the Tharsis ridge (Fig. 1). It was discovered after the geophysical prospecting methods described below had defined a target zone for diamond drilling.Since the proving of copper mineralisation by drilling, the corridor orebody has served the vital function of a convenient known target body for the orientation of more recently developed geophysical methods. Traversing of the orebody by these new methods has provided experience for the evaluation of anomalies elsewhere.Some of the methods applied had not been used in Australia before, and were introduced to the west coast of Tasmania through the undertaking there of modern regional exploration programmes. The authors feel that the information gained could be of assistance to others engaged in geophysical prospecting.HISTORY OF DISCOVERYProspecting in the Mount Lyell district has been more or less continuous since 1881. The first geological report was published by Thureau (1886).In 1934, Blazey and Douglas (1934-38) commenced geophysical surveys at Mt. Lyell using the equipotential method.They obtained anomalous indications in several discrete zones and actually detected the south-east half of the corridor orebody but their work never became the basis for...

Jan 1, 1961

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By J. Ruzicka

IN creep testing, material is subjected to a constant load, preferably at a constant temperature, and its rate of deformation is measured. The method of loading can be of various types but in this paper only creep testing under tensile load will be considered. The ordinary tensile test is essentially a comparison test in conditions that frequently bear little or no relation to those under which the test material is to be used in service. The purpose of creep tests is to measure the strength of the test material at slow rates of deformation that more nearly approach the rates realized in service. One purpose of this paper is to illustrate that the creep test, in addi-tion to its value as a service test, is superior to the ordinary tensile test as a sensitive tool for the comparison of certain metals in investigative testing. The other purpose is to describe equipment having distinctive features of design that make it especially suitable for such tests. Representative data obtained with this equipment on a group of rolled zinc-base materials are given. These data are compared with those from practical comparison tests of the creep type on weatherstrip fabri-cated from the same group of materials. The comparison illustrates the value of the fast creep test and of the equipment.

Jan 1, 1937

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

By Jack Eloranta

The winning of metals often requires fine grinding of very hard ore. The US Bureau of mines measured compressive strengths exceeding 100,000 PSI (700 MPa) in Minnesota taconites. Grinding down to 300 mesh (50 µ) is required for some fine-grained taconites. While other metal ores may not be as strong, significant grinding costs are the rule rather than the exception. One author recently reported that a 7% drop in grinding costs would fully offset a doubling of the drill and blast budget. Another author found that drill and blast costs were 13% of the costs of producing iron ore concentrate while fine crushing and grinding were over 60% of the cost of producing concentrate.

Jan 1, 2013

The lead concentration of flotation feed ore slurries is determined using two ?-ray absorption gauges mounted directly on a 6 in. diameter flotation feed pipeline. One gauge is a conventional "density" gauge using CS137. The other is a "lead-sensitive" gauge, which depends on the preferential absorption. by lead of 225 key y-rays resulting from Compton backscatter of CS137 y-rays.Gauge outputs are combined using an analogue computer the output signal of which is directly proportional to the lead concentration of the pulp. The accuracy of measurement of the pulp lead concentration is ± 3·6 per cent for ore slurries with lead concentrations in the range 0'07-0·16 g/c.c. and pulp densities 1.43-1.60 g/c.c.This paper sets out the development of the technique and details are given of the two experiments (1964, 1966) conducted in the plant at North Broken Hill Limited. The installation of the two-gauge system inthe plant during May 1968 is described. Details are given of the calibration technique used and the results obtained.

Jan 1, 1969

By R. V. Ramani

In this the available information friction factors and leakage report, on characteristics are reviewed and summarized. The use of Penn State Mine Ventilation Simulator (Volumes II and III of the Final Report) to analyze the sensitivity of the ventilation system to the changes in leakage and friction factors is discussed with examples. In simple ventilation systems, the results of changes in leakage and friction factors can be easily solved and explained by the laws of air-flow. In complex systems, with fixed quantity branches and multiple sections, the effect of changes in leakage and friction factors cannot be generalized. This study points out the importance of good input data for obtaining reliable information from computer analyses and demonstrates the application of simulators to analyze the effectiveness of ventilation systems. An extensive bibliography on friction factors, leakage characteristics and ventilation economics is included.

Jan 1, 1977

By J. Koster

[In 1178 thn S-00n of thr !~Viluralcal Divicion, pur--'11 cf Mines, bcran an o. 't iv in': n-t!Y_Vnn of vothod; for recoverin'-1, Achol, copp~r, nK precioun notnin Zycn o;. -z of tic Bunkcrvillo KOH& in Clark County, Tcv. Tho Bunkcrvillo ran arc of t,-j)(,e of -iincrilization similar to that of 02 SWbury, Ontario, CannO, nichvl dc-?o?-:.t,. At prcoont, only n anall tonnes? p of ore has loan cxDr)scd in t*ic' :hui:er7ilIp rc: inn, ann. there is decided nce! for orjn: izod OrospectiAg ina drvclo-nnnt "crk there. It wann believod, howevar, t4it the dc,cuits varo 3ilficUntly siSnIficant to warrant an investigation iito their]

Jan 1, 1939

The literature pertaining to the electrochemical reaction at the anode during electrolytic reduction of alumina by the Hall-Heroult process is not in universal llgreement about the gaseous product. The possibility of electrochemical formation of CO at the anode was examined using existing data. Although the thermochemistry favours co-evolution of CO and CO2 with CO as the major product, the mechanism of the reaction shows this is unlikely. Since the origin of CO can be more logically explained by non-electrochemical mechanisims, it is concluded that CO2 is the only product from the electrolytic reaction at all current densities.

Jan 1, 1967

By N. Behnood

"This paper describes how material selection, quality assurance, and failure investigation play important roles in the efficiency and safety of mining and metallurgical operations.INTRODUCTION Material selection, quality assurance, and failure investigation are all complementary elements of materials engineering in the application of materials technology for failure prevention. Based on commodity price increase of 300% between 2002 to 2013 [1] and increased cost ofcapital projects and operation, equipment failure, which in some cases causes complete shutdown of the operation, becomes a vital importance in mining and metallurgical plants. The following sections present a number of examples from many failure cases experienced by the author during his three decades of work as a materials engineer in the mining industry."

Jan 1, 2015

Arizona copper mines produced nearly 67% of the nation?s copper in 2000, according to a report released by the Arizona Mining Association (AMA). This was a slightly larger share than in 2000 despite large reductions by one major copper producer and production cutbacks at several other facilities. In 1999, Arizona mines produced 64% of the nation?s copper. The report was prepared by economist George F. Leaming of the Western Economic Analysis Center in Marana, AZ. It also showed the copper industry had a $4.6-billion impact on the Arizona economy in 2000, a 26%decline from 1999. This is the lowest financial impact since 1973 and less than half the record reached in 1981of $9.6 billion. The decline is primarily due to a sustained low copper price and a slow-down in the US economy. The mining industry?s impact included combined direct and indirect contributions of $1.283 billion in personal income for Arizona residents, the equivalent of 43,000jobs. More than 5,000 of those jobs were in state and local government and more than 18,000 were in trade and ser-vice businesses. The copper industry directly employed fewer than 8,000 people statewide in 2000. This was down about 23% from 1999.

Jan 1, 2001

By D. M. Rippley

THE St. Lawrence Seaway Project ranks with the greatest engineering undertakings of all time. A summary of major materials going into the construction of this project, shown in Table I, will assist in an appreciation -of this fact. These data relate to Seaway construction only, and it should be remembered that two large-scale power projects are in the construction stage on the St. Lawrence river concurrently with construction of the Seaway. A project of such magnitude as the Seaway would attract widespread interest even if it were being constructed in a remote area. The fact that it is located in a heavily populated and developed section of both Canada and the United States has done much to enhance this interest, and in many ways complicates the problems confronting the engineer in the design and construction phases. Many consider the St. Lawrence Seaway to be a new idea that has developed within the past decade - such is far from the fact, because the St. Lawrence River canal systems have existed for more than a century, and the Seaway Project is but a new, larger, and more efficient version of a continually expanding facility.

Jan 1, 1957

By M. Zaske, E. R. Mortensen

"As mine operators continuously look for ways to improve functionality and increase the capacity of their facilities, existing process equipment is often pushed to and past its designed limitations. As a result, equipment manufacturers are asked for economical solutions to meet redefined processing needs. Newmont Mining in Nevada was faced with such a need in its carbon-in-leach (CIL) train. In a collaborative effort between Newmont and Derrick Corp., tests were conceived to assess the viability of drop-in replacement screens using a three-dimensional screen panel. The synthetic pyramid screen panel was designed to increase flux while maintaining the existing equipment footprint. The test is the end result of an ongoing research and development project that Derrick undertook in an effort to refine and upgrade its urethane screening media. The application of this new screening media is presented for this CIL application along with future plans to implement the technology in trash, safety, carbon dewatering, carbon sizing and other scalping applications.In spring 2014, Process Machinery Associates (PMA), Derrick’s local area representative, met with Newmont to discuss the operation of the in tank screens in the CIL train at Twin Creeks, near Golconda, NV. The process was originally designed for about 12+ kt/d (13,000+ stpd) but the throughput has been steadily rising since the plant was commissioned. Newmont now requires 14.5 kt/d (16,000 stpd) to be processed. The original screens were running at their maximum capacity, and Newmont required additional screening capacity to continue the upward trend in production.Physical separation by use of screening is one of mineral processing’s oldest methods. Screening media can be prone to blinding and pegging, and the necessary support structures required for finer apertures result in smaller open areas. Therefore, more screening area generally requires larger panels and, thus, larger machines, screening media that does not blind or a combination of both.In an effort to avoid larger machines, Derrick had been working on a revolutionary threedimensional panel that would add nonblinding screen area in the same footprint of an existing machine. Alpha testing of the new screen panels began at Newmont Mill 2/5 in July of 2013. It was still occurring when PMA approached Twin Creeks about beta testing a refined machine and pyramid panel. After presenting the initial results, Twin Creeks determined that an upgraded machine and pyramid panels would be a possible solution to meet production needs. The testing of a machine eliminated the risk of capital costs to Newmont and provided Derrick the opportunity to obtain additional data."

Jan 1, 2015

By R. J. A. Fricker

IT is the purpose of this essay to give a reasonably complete description of shaft sinking under a rock pentice in a small Northern Ontario gold property. Hallnor is in many ways an exceptional mine, but the sinking operations here described are but typical examples of the excellent practice for which Canadian mines and mining engineers are justly famous the world over. The worth of the subject lies, therefore, nor in its originality, but in its soundness; not in the spectacular, but in the economical and safe. Attention is particularly drawn to the excellent safety record and to the exceptionally low overall sinking cost. INTRODUCTION Prior to April, 1939, the Hallnor No. 1 shaft had been sunk vertically to a depth of 997 feet below the surface. It is a three-compartment shaft, 19 ft. 10 in. by 7ft. 7 in. outside the timbers (see Figure 1).

Jan 1, 1941

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By George J. Tamaro

The design and construction of foundations in the New York City area are usually dictated by the widely varying geologic conditions encountered in the five boroughs, particularly along the spine of Manhattan Island. Rock extends well above sea level at the northern reaches and falls to depths in excess of 250 m at the barrier islands at the southern extremities. These highly variable geologic conditions, significantly affected by glacial activity, dictate different design and construction approaches throughout the five boroughs of New York City. Extensive rock removal is required at the north while long piling is dictated in the south. Similar changes can occur within a project site on Manhattan Island. This paper will describe these conditions in general, will identify the various solutions used to solve these problems and will summarize various foundation types used in the New York City area.

Jan 1, 2000