Search Documents

By F. R. Hensel

P. R. Kalischer.*—I should like to amplify a little one of the points made by Dr. Hensel, and rather violently disagree with him at the same time. He brought out the point that when the higher forming pressures are used on the green compacts there is a marked decrease in the density as sintered. We found that to be true and, of course, many of you notice that that is true with copper compacts also. But, in my opinion at least, it is not true that the expansion is due to entrapped air. We have vacuum-pressed both silver and copper compacts and obtained almost exactly the same numerical expansion as we secured by pressing in air. The powder, however, that is vacuum-annealed does show a slight decrease in expansion on sintering, but almost the entire increase on expansion can be overcome by very slow rates of heating. And it is our opinion that a majority of the expansion is due to dissolved oxygen in the discrete metal particles themselves rather than to entrapped gases. Another interesting observation that we have made is that often with silver or copper compacts it is desirable to silver solder or braze the compact into some part of a piece of equipment after completing powder metallurgical operations on it. If such a compact is sintered and coined, say a silver compact, given an initial forming pressure of 10 to 15 tons per square inch, and sintered, there is an adequate amount of shrinkage and it can be coined at about 50 or 60 tons per square inch and bring up the density nearly to theoretical. If, then, that compact is silver-soldered into some part of a fixture or a machine, it will expand very beautifully, and the only way that this can be overcome. as far as we know, has been to reanneal after the coining operation at a temperature higher than is to be used in any subsequent operation. In that way, a density very nearly theoretical can be achieved, but the coining operation cannot be carried to the excessively high pressures or expansion and bubbling of the compact will occur again.

Jan 1, 1945

By P. R. Moyer

"INTRODUCTION The Federal Explosives Act (55 Stat., 863), as amended, was passed by Congress on December 26, 1941, and became effective immediately; it amended the Act of October 6, 1917 (4o Stat., 385). The purpose of the Act was to regulate the manufacture, storage, use, and possession of explosives in order to prevent sabotage and to assure that explosives and ingredients would not fall into unauthorized hands. Under the provisions of the Act, the Director of the Bureau of Mines was authorized to administer its provisions under the supervisions of the Secretary of the Interior.EXPLOSIVES-CONTROL DIVISIONTo administer the Act, necessary personnel were employed in accordance with the appropriation made from a special presidential fund and later by Congress, and the Explosives Control Division was organized as a part of the Health and Safety Branch of the Bureau of Mines constituting the fourth division of that branch. A central office was established in Washington, D. C., and field offices were designated largely at the offices of the Health and Safety Branch throughout the country, and 50 explosives investigators were employed and assigned to work from these offices under the direction of the district engineers of the eight districts into which the United States is divided by the Health and Safety Branch. The territory assigned to each investigator was based on the approximate amount of explosives stored in that area; however, smaller territories were assigned to investigators stationed near the Pacific coast, which was indicated as critical by the armed forces."

Mar 1, 1947

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4. N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management 156, Ataturk Bulvarl-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcade Bids. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1893 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs and Mine Management ` 188, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 8 Haward-Canfleld Bldg. Santa Barbara, Calif.]

Jan 1, 1952

[RALPH ADAIR Ore Dressing Consultant Bull Mtn. Rd., Asheville, N. C. Phone 4-1693 JAMES A. BARR Consulting Engineer Mt. Pleasant, Tennessee Washington, D.C. BEHRE DOLBEAR & COMPANY Consulting Mining Engineers and Geologists 11 Broadway New York 4, N. Y. I. R. BERENT Engineering Consultants and Contractors Mineral Exploration, Mine Evaluation, Mine Designs, and Mine Management 156, Ataturk Bulvari-Ankara, Turkey BLANDFORD C. BURGESS Registered Professional Engineer Mining Consultant Monticello, Georgia GLENVILLE A. COLLINS Mining Engineer Uranium examinations Cable "Coins" 210 La Arcada Bldg. Santa Barbara, Calif.]

Jan 1, 1952

By R. L. Marek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalitics coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance. [ ]

Jan 1, 1930

By Parry. V. F.

"SUMMARY This report reviews the status of the packaged-for industry as of 1941. A field study was made of 35 representative plants to obtain technics and economic data on different types of processes used to make packaged fuel in the Central States. The report includes a classification of processes, photographs of typical operations, designs of different plants, an analysis of costs of manufacture, and a study of the physical and chemical properties of fuel cubes.It was observed that many of the smaller plants were having troubles in the manufacture of packaged fuel as the price of materials and costs of labor advanced toward the higher levels of 1942. In some instances, the total cost of manufacture was as high as $5.00 per ton, while in the better, medium-sized plants it was approximately $3.25 per ton. The direct manufacturing costs, excluding investment and depreciation, ranged from $3.17 to $2.37. These costs permit almost no profit at small plants when packaged fuel sells for the same price as competing lump coal under conditions existing in 1941-42.It was found that the predominant troubles in plants were due to inadequate drying and insufficient mixing of the starch binder. It was ob¬served that in the better plants, where proper mixing of binder was attained high-quality packages were made if 50 to 70 percent of the moisture was removed in the drying ovens. Experimental data obtained in the laboratory show the relationship between the temperature of dry air and the time required to remove different percentages of moisture in wrapped orunwrapped coal cubes.The average physical and chemical properties of fuel cubes made by five processes are listed, and tentative standards for minimum physical qualities and methods for measuring quantity are giver."

Jun 1, 1944

By R. L. Merek

There were 63 fatalities in the California petroleum industry in 1929, the largest number in any year since 1923 and an increase of 34.0 per cent over 1928, when 47 men lost their lives in the drilling, producing, manufacturing, and marketing divisions of the industry. It will be observed from the accompanying chart that after following a consistent decline for 4 years, the fatality curve turned upward in 1923 and advanced sharply in 1929. Although this increase in fatalities coincided with a period of intensive development it tends to indicate some laxness in the industry during a period of increased hazards. Intensive drilling campaigns are usually started hurriedly and conducted with a great demand for speed, and the result is that accident-prevention work is too often relegated to a position of minor importance.

Jan 1, 1930

Researchers, medical organizations, statisticians, and others often use data on the nature and rate of occurrence of occupational diseases in directing their efforts and plans. Very often this information is developed from the reports of the States which describe the nature of work¬men's compensation claims and awards and the frequency with which they are made. To be meaningful, the statis¬tical information must be viewed in the context of the State laws involved. There is considerable variation among the laws of the different States. The Bureau of Mines has responsibilities for protecting the health of persons employed in the mineral industries and for the development of useful mineral products. To assist the Bureau in the accomplishment of its objectives, this compilation has been undertaken. For the benefit of the mineral industries, and any others who may have a similar interest, this volume is made available. An earlier compilation of the Bureau of Mines on this subject was published in 1952.4 However, during the intervening years, sufficient changes have been made in State laws to warrant completely recompiling the information. This publication includes the laws of the States, the District of Columbia, Puerto Rico, and the Virgin Is¬lands through 1964. Only those portions of the workmen's compensation laws which apply to or as ' related to occupational diseases are presented, and in each case enacted additions to and deletions from the basic law have been incorporated into the text of the law, thus snak¬ing it unnecessary to search out the various amendments made each year.

Jan 1, 1967

By Frederic P. Dewey

The Bureau of the Mint of the United States Treasury maintains 13 ofEces for the purchase of gold-bullion, and this paper describes an investigation to establish the reasonable differences in the assay-results at the various institutions which may be commercially allowable in the settlements between them. Beginning with the comparative assay of proof-gold at the Philadelphia mint and the Utrecht mint, which shows 0.00002 as the closest agreement now possible, nine tables of comparative results, taken from the regular work of the service, are given..These tables begin with very fine gold, produced in an electrolytic refinery, showing close agreement in the assay-results, and follow through decreasing gold fineness and increasing amounts and complexity of base metals to very impure and complex bars produced at cyanide-mills, some of which give widely-varying results. Next is given a series of results on samples, prepared and sent out to various laboratories in the service, to test the influence of different metals and various combinations upon the agreement of the assay-results ; 11 samples were sent out and each one was assayed from 44 to 71 times, making a total of 623 assays. To these ire added 107 assays of identical samples of coin-gold. On a previous occasion,' I have endeavored to show the degree of accuracy that may be expected in the ordinary everyday analysis of various materials, and on another occasion,2

Jan 1, 1910

By H. C. M. Gordon

IT is essential to the success of any mining op::ration that the roadways through which the material wrought and ocher materials and supplies are to be transported should be kept in such condition that this transportation cart be effected rapidly and without difficulty. The longer the roadway and the greater the tonnage to be taken over it, the more necessary it becomes chat the construction and maintenance of the road be such chat traffic delays can be reduced co a minimum. le is proposed co deal with the development and construction of roadways serving longwall operations and, since a recreating system of longwall is worked, as a rule, only where roadways driven in the solid coal can be readily maintained, the discussion will be confined co advancing longwall roads which are driven through areas from which the coal seam has been totally extracted. In order to construct a roadway through extracted ground in such a manner that it will remain in a state of reasonably good repair without undue maintenance, it is necessary chat everything possible be done to bring the overlying strata co a state of equilibrium as quickly as this can be effected, and the operations should be so planned that future workings will not disturb the equilibrium so set up more than can be avoided. Obviously, the readiest way to obtain a stable roadway is to develop it by tunnelling through a settled waste. However, this cannot always be done, as some of the roadways must be developed and constructed as the walls progress, but level or lateral cut-offs can be constructed in this manner. Main-slope roads can be developed in a similar manner after the coal has been extracted and a waste formed for at !east five hundred feet on either side of the line of the permanent roadway from temporary subsidiary roads developed for this purpose along one or other of the flanks of the waste to be formed. This interval must be obtained in order chat the lacer extraction of the seam will not set up movements in the waste immediately overlying or adjacent to the constructed roadway, thus upsetting the equilibrium of the strata and distorting the road.

Jan 1, 1940

By W. R. Ingalls

THE following chronology presents the history of lead-mining in the United States in a brief form and is a useful reference in connection with the statistics of production 1621. Lead was mined and smelted near Falling Creek, Va., to supply the local demand for bullets and shot. This was the first mining and smelting of lead in what is now the United States. 1632. In a report made on the minerals of New England, lead-ore is mentioned. (Bishop, I., 470.) 1650. Supposed beginning of mining by Jesuits in Pima county, Ariz. 1651. Grant of lead-mine at Middletown, Conn., to Gov. John Winthrop.

Jan 9, 1907

By F. H. Willcox

This publication is the third of a series of reports on hazards and the prevention of accidents at blast-furnace plants that is being published by the Bureau of Mines, Technical Paper 106a being the first and Technical Paper 136b the second of the series. This bulletin, which is arranged in three parts, treats of the causes and prevention of blast-furnace breakouts, explosions, and slips. The first part discusses blast-furnace breakouts, the hazards therefrom, causes, and features of furnace design and methods of operation that tend to prevent breakouts or lessen their number, and points out safety measures to be adopted. The second part takes up the theory and causes of gas explosions at blast-furnace plants and reviews the better methods in use for handling gas. The third part analyzes the causes of hanging and scaffolding in blast furnaces, with the resulting slips that frequently cause injury to the plant and danger to the workmen, describes features of construction and furnace design and methods of operation employed to prevent hanging and slipping, and suggests precautions and safeguards.

Jan 1, 1917

By Yan Yuan

Stable Nitroxyl polymers, such as poly (2,2,6,6-tetramenthyl-1-piperidinyloxy-4-yl methacrylate) (PTMA), are known to be effective as cathode active materials for lithium rechargeable betteries.The nitroxide radicals displayed a reversible and very rapid redox performances.We present a new synthesized method to get PTMA powder, then a doctor-blading method was used to prepare the PTMA composite electrodes, enabling successful production of homogeneous electrodes. It was characterized through FT-IR and SEM methods.The organic radical battery consists of lithium metal anode and PTMA cathode with an active material content of 65wt%.The best performance is achieved with a thin cathode that shows nearly 100% utilization of the active material (111mAh/g) at 0.1C.Through the electrochemical tests, it was found that there was a stable plateau at 3.5V while discharging. Besides, the cycling stability and rate capability were measured in detail. Although they showed a certain quantity of irreversible capacity on the first cycle, the capacity stabilized after the second cycle.

Jan 1, 2009

By AIME AIME

COMMITTEES. CANAL ZONE.-Col. George W. Goethals, U. S. A., Chairman; Lt.-Col. H. F. Hodges, U. S. A. ; Lt.: Col. D. D. Gaillard, U. S. A. ; Lt.-Col. William L. Sibert, IT. S. A. ; H. H. Rousseau, U. S. N.; Col. W. C. Gorgas, U. S. A.; Maurice H. Thatcher ; Joseph Bucklin Bishop ; Lt.-Col. Charles F. Mason, U. S. A.; S. B. Williamson ; Major Eugene T. Wilson, U. S. A. ; Edward Schildhauer ; Henry Goldmark ; Edward C. Sherman ; W. G. Comber ; W. B. Corse ; J. A. Walker; Joseph A. Le Prince; J. A. Smith ; Lt. Frederick Mears, U. S. A. HAVANA.-V. T. Polledo, Chairman; Diego Lombillo Clark, Jose Primelles, J. R. Villalon, Jose Artola, J. Ducassi, Luis Morales, Enrique Montonlieu. ENTERTAINMENT ON SHIPBOARD.-William L. Saunders, Chairman; Mr. and Mrs. S. D. Warriner, Mr. and Mrs. Thomas Robins, Mr. and Mrs. George.D. Barron, Mr. and Mrs. R. B. Watson, W. E. Greene. GENERAL MANAGEMENT. .Joseph Struthers, Chairman; Albert E. Vaughan. There were ten sessions of the Institute held for the presentation and discussion of, technical or professional papers. Eight of these sessions were held on the steamer while en route, and two in the ball-room of the Hotel Tivoli, at Ancon, C. Z. Mr. David W- Brunton, President of the Council, presided at all the sessions, except the sixth, at which Mr. Charles Kirchhoff, past President, occupied the chair. The following list includes the papers presented in oral abstract by the authors: First Session., October 24. The Summit Hill Mine-Fire, by W. A. Lathrop, Philadelphia, Pa. Mine-Fire at the Calumet and Hecla Mine, No. 8 Shaft., by S. D. Warriner, Wilkes-Barre, Pa. Fire in the Big Lick Stope, Lykens Valley and Williamstown Colliery, by R. V. Norris, Wilkes-Barre, Pa. Mine-Fire in the Hecksherville Valley, Schuylkill Field, Pa., by W. J. Richards, Pottsville, Pa.. Fire in the Monarch Mine, near Rock Springs, Wyo., by S. A. Taylor, Pittsburg, Pa.

Dec 1, 1910

By Grant R. Brown

This report presents the results of a study examining the relationship between supervisor characteristics and performance in underground coal mines, The specific objectives of the research include; document tasks performed by first-line supervisors during a normal shift; explain why supervisors carry out their duties as they do: identify salient characteristics of effective first-line supervisors; and formulate criteria for selecting and developing candidate supervisors. To accomplish the study objectives, on-site observation and data collection was carried out at 13 underground mines in Illinois, Ohio, and Pennsylvania. One hundred thirty-eight first-line supervisors were observed during a full work-shift and discussions with the supervisors and the mine superintendent were held during the course of the visit. The observational data from the study provide a detailed description of what supervisors to during their shift. The report begins with an introduction discussing the problem being studied and objectives of the research. The literature related to supervisor selection is then reviewed. The following section describes the research design including data collection procedures and statistical methodology used in the study. The next sections present the analysis of mine, section, crew, and supervisor characteristics. The report concludes with a discussion of the results of the study and recommendations concerning supervisor selection and development.

Jan 1, 1987

By Donald Christofferson

This report documents the program conducted to demonstrate the application of a flywheel-powered propulsion system to underground mining shuttle cars. Such application can replace the present electrical trailing cable common to most shuttle cars and thereby eliminate those safety hazards, maintenance problems, and haulage route limitations inherent in the trailing cable. Described are the activities undertaken to specify and design a flywheel of optimum size, shape, and material; to identify the best concepts of input and output systems; and to achieve installation of the power package into a shuttle car. The resultant Flywheel-Powered Shuttle Car is an FMC Model 6L shuttle car, 6-ton capacity, 20-ton gross vehicle weight, powered by a flywheel system with 4.5-kilowatt-hour usable energy. The completed vehicle was delivered to the Bureau of Mines in Bruceton, Pennsylvania, for testing and evaluation.

Jan 1, 1986

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By C. Yi, M. Onifade, B. Genc, S. Dineva, T. Zvarivadza, M. Khandelwal

Deep hardrock mines worldwide increasingly face rockbursts as mining depths increase. These events result from the accumulation and sudden release of stress, causing rockmass damage and posing major safety and operational challenges. This paper focuses on destress blasting as a critical strategy to mitigate rockburst hazards. Although limited practical experience exists in Swedish deep hardrock mines, international case studies demonstrate that, when well implemented, destress blasting redistributes peak stresses by promoting controlled fracturing around mining excavations. The success of such techniques is highly dependent on site-specific factors such as stress regime, rockmass brittleness, structural geology, and blast layout. Although destress blasting is especially effective in massive, brittle rock under high stress, typical conditions for strainburst prone environments, its design cannot rely solely on numerical models. Simulations can offer preliminary evaluation of stress redistribution trends and guide early design assessments but their current limitations, including sensitivity to input data and simplified fracture mechanics, mean they are best used as supplementary tools rather than final decision-makers. Field trials, supported by microseismic analysis and fracture mapping, remain essential for validation. The study critically synthesises international experiences and presents a structured framework for destress blasting design, offering practical and academic perspectives aligned with Swedish geological conditions to support safer and more efficient application in deep hardrock mines.

Jun 27, 2025

By The Staff

BEFORE going into detail on the subject to be presented, a brief outline of the Company's earl y history would not be out of place. Prospecting and mining on a small scale was started in 1876 on the site of the present open pit at Thetford Mines. The property was purchased from the Crown in 1878 and Johnson's Company was incorporated in 1885. It is owned and operated today by descendants of the original shareholders. Many employees, through their fathers and grandfathers, have service records dating back three generations. The principal asbestos deposit at Thetford Mines is pear-shaped, with surface dimensions of about 2,200 feet in length by 1,300 feet in maximum . width. Its long axis strikes northeast and the dip is nearly vertical, but irregular in detail. It is known to extend to a depth 1,200 feet below the original surface, but its area at that depth has not been determined. Ownership of this deposit is divided among three active Companies: the Asbestos Corporation, Limited; Bell Asbestos Mines, Limited; and John-son's Company. Johnson's Company owns a section about 1,000 feet in length and 500 feet in width, bounded on the northeast by the King mine of the Asbestos Corporation and on the northwest by the Bell pit. On Johnson ground, there was originally a large outcrop o~ asbestos rock which dipped toward the south below overburden. This was mined until recently by open pit, the overburden being stripped off as far southward from the original outcrop as was economically possible. As the. pit was deepened, within side walls maintained at a maximum safe slope, its floor area, of course, became progressively smaller, and eventually the pit would have wedged out against the Bell property line. It became necessary, there-fore, to introduce some other method of mining before production became seriously curtailed by a shrinkage of the pit area.

Jan 1, 1941