Search Documents

By Michael Leslie Connor

The paper point out the services of the london metal exchanged on the mining.The investigation is divided at two parts: the tradings sessions and dealing and delivery dates. As well as, the london metal exchanged serves the world metal trade at large in three ways: a daily market price, a physical market and the insurance against market fluctuations.

Nov 20, 1969

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By W. H. Fertl, S. J. Pirson

Well logging techniques, as used successfully in oil and gas exploration, can also be used to give a detailed evaluation of drill holes through industrial mineral deposits such as sulphur. This paper describes the logging tools used gives the theory behind the well-log interpretation and discusses the application of the method in sulphur-bearing limestone and m more complex sulphur deposits.

Jan 1, 1970

By Georges Delemontex, Nigel Grigg

"Pre-concentration of precious metal and base metal ore types is becoming more relevant with the discovery, development and operation of many lower grade deposits around the world. The fluctuations in metal prices and currencies expose many mines to risks especially dealing with low and variable ore grades. Pre-concentration, the process of concentrating the valuable metal into a smaller mass yield, effectively results in the introduction of higher feed grades to milling circuits. Gangue rejection, the removal of lower S.G. waste rock from the circuit, not only results in higher downstream grades but also potentially removes harder, non-valuable mineral, providing significant power savings within the circuit. The pre-concentration or ‘gangue rejection’ process offers a number of benefits when considering the treatment of marginal ore deposits, especially if it can be performed at a coarse crush size; these benefits include a reduction of the operating costs and the feed of more metal units to the mill. Gekko Systems has effectively utilized the Inline Pressure Jig (IPJ) to pre-concentrate the valuable metal, achieving high primary recoveries into a range of mass yields resulting in upgrade ratios between 2 and 10 times. This paper explores: the benefits of pre-concentrating ‘marginal’ ore deposits prior to the milling circuit; the selective rejection of ore types that may affect either the recovery or comminution process; and also looks into the potential to effectively reduce the ‘cut-off’ grade when considering the mine planning process. Case studies of projects using the IPJ to pre-concentrate and reject gangue are also included. Pre-concentration and gangue rejection provide the potential to develop marginal ore deposits, thus providing higher grades, less gangue and more metal at a lower operating cost to producers."

Jan 1, 2014

By Yanxu Shen, Cheng Liu, Zhijie Chen, Hao Chen, Huimin Gao, Zijie Ren

Fluorite, a kind of critical non-metallic minerals, is the primary source of industrial fluorine. Sodium oleate (SO) is commonly used as the collector of fluorite ores. However, because of its some features (such as the low solubility, high solidifying point, and poor dispersion of SO) at low temperatures, it profoundly inhibits its collecting ability as well as the flotation performance. Herein, we have developed a low-temperature-resistant collector for the efficient flotation separation of fluorite from quartz. The advantages and disadvantages of the SO and sodium petroleum sulfonate (SPS) were analyzed by comparing the performance under different temperature conditions. The results of flotation tests suggest that SPS exhibited much better collecting performance than SO under low temperature. The flotation mechanism of the two collecting agents were further analyzed by contact angle measurements, zeta potential measurements, Fourier-transform infrared spectroscopy (FT-IR), and flotation kinetics. The results indicated that both collectors can selectively undergo electrostatic and chemical adsorption with fluorite, with no adsorption on quartz surface. The sulfonic acid group in SPS is a hydrophilic functional group, which has a relatively higher solubility in water. Therefore, the water solubility of SPS is better at low temperatures.

Sep 30, 2021

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011

By J. O. Marsden

This paper presents an overview of the innovative methods for gold and silver extraction that have been put into actual practice in North America since 1987. It is an update of a paper of the same title which was presented by Sass and Mansanti at the AMC conference in San Francisco in 1987. New practices, new equipment and variations of older practices that have been introduced in the last five years are discussed in each of the following categories: process selection trends, comminution, gravity concentration, flotation, oxidation, agitated and vat leaching, heap leaching, solution concentration and purification, zinc precipitation, electrowinning, tailings disposal detoxification, and reclamation.

Jan 1, 1993

By F. A. Rutledge

[An a part of the United States Department of the interior program for the development and use of Alaska raw materials, the Bureau of Mines is conducting an investigation of deposits of nonmetallic minerals accessible to the Alaska Railroad for use in building; materials is In the Alaska Railroad-belt area. The results of the investigations, to date, indices that raw materials for the preduction of brick products are in plentiful supply as cloy in the Anchorage area, as fire clay at Sheep Mountain, and as shale in the Healy Creek coal formations near Healy, Alaska.]

Jan 1, 1953

By Bernard H. Hertlein

Transportation system structures have come under very close scrutiny in the last couple of years, largely due to the damaging effects of disasters, both natural and man-made. In the Pacific northwest and California, earthquake risk is a major concern. In the central and eastern states barge impacts on bridge piers and docks are a big worry. In all cases of bridges over water and waterside structures, scour is a primary concern. Some of the results of this scrutiny have been changes in design and construction methods, and the introduction of more testing to supplement field inspection during construction, and throughout the service life of the structure. Future construction of bridges and docks will almost certainly see a continuing growth in these practices. Where foundations are concerned, particularly for bridges and waterside structures, many state and local authorities have started specifying drilled shafts rather than driven piles. Where the shafts must be constructed under water or slurry, visual inspection of most of the work is impossible, and one of several different Nondestructive Tests (NDT) is often specified. Contractors' experiences with these methods have varied considerably, and there is a great deal of controversy in the deep foundation industry over the reliability of NDT methods for assessing the integrity of foundation shafts or piles. The author has had more than 15 years of practice with the various NDT methods for deep foundations, on projects all over the US, particularly foundations for bridges and dock structures, and has developed an understanding of the "NDT controversy" as it has become known. In particular, experiences in the Pacific Northwest, California, and Alabama have illustrated the reasons for the controversy. This paper reviews these experiences, and suggests some steps that owners and contractors can take to reduce the risk of inconclusive or downright inaccurate test results.

Jan 1, 1998

Electricity supply constraints in SA are increasingly challenging mines to operate more energy efficiently without reducing production output. Mining compressed air systems are well known to be operated inefficiently and are also a major power consumer. Two available and proven technologies can be applied on new and existing mines to replace or and optimise available compressed air facilities and achieve meaningful reductions in electrical power consumption; ? Hydro powered drilling and mining is significantly more energy efficient than compressed air and provides drilling rates that are twice as fast. ? Stope drilling systems using compressed-air or water drills allow further energy savings. The technologies are discussed and a broad strategy to selectively apply these them together is presented.

Jan 1, 2008

By A. R. Dover

The Richmond-San Rafael Bridge is a 6.92 kilometer (4.3 mile) long major toll bridge span that crosses the northern San Francisco Bay in a highly seismically active region. Tutor-Saliba / Koch / Tidewater JV was contracted by Caltrans to conduct a comprehensive seismic retrofit. The JV provided geotechnical planning and quality control services as described herein, under normal oversight by Caltrans. Part of the robust foundation retrofit design included the installation of 26 new, large diameter piles, including eleven 3.81 m (12.5 ft) diameter, cast-in-drilled-hole (CIDH) marine piles that were drilled 9.15 m (30 ft) into the bedrock beneath the Bay, where the water depth ranged up to about 21.3 m (70 ft). These reinforced concrete-filled composite piles have a steel shell permanent casing from the bridge substructure pile cap through the water column and 30.5 to 39.6 meters (100 ft to 130 ft) of marine sediments to the top of rock. This paper discusses construction, inspection (ranging from the QA employed in the planning of the CIDH pile installation methods and equipment to the actual construction inspection required for the routine installation of the shafts), problems that were encountered during construction, and the solutions that were developed and implemented. Inspection, particularly with the usual difficulties in the marine environment, coupled with the difficult and complex bedrock conditions was particularly challenging, and ranged from non-destructive testing to "in-water, inshell" diver inspection. Similarly, the complexities of dealing with both the steel casing "riser" and the associated drilled shaft (rock socket) portion of these composite foundation elements created some unusual issues. The paper also presents important lessons learned from the project.

Jan 1, 2008

By A. E. Schwaneke

Plans and specifications are given for constructing a quartz composite oscillator designed to measure internal friction in metals and alloys . The characteristics of the system are listed , and detailed procedures for its operation are explained . Typical measurements on manganese - copper alloy , on single - crystal magnesium , and on polycrystalline magnesium are shown to illustrate applications of the system .

Jan 1, 1964

By Larry DeGraff

With the increase of new mine development in the past several years, many coal mines have decided to self- perform the design and construction for their slope development projects. The development process of determining the proper configuration is challenging, and a major economical consideration. Greenbrier Smokeless Minerals engineering staff and consultants, along with DSI/American Commercial, developed a support configuration that was best suited for their slope. The developmental process took into consideration the length of slope, depth of slope at the high-wall transition, economics of a single or multiple entries, waterproofing, stresses on the steel supports and lagging during the backfilling operation. This paper describes the developmental concept of using a single entry, side by side configuration, using steel ?Banjo String? supports with steel plank lagging, to develop a long term permanent installation in a cut and cover application.

Jan 1, 2009

By Malcolm J. A. Swallow

In June 1997, Mount Polley Mining Corp., a division of Imperial Metals Corp., completed an 18-kt/d (20,000 stpd) gold-copper mine in central British Columbia. Fast-track construction and extensive off-site construction were combined with an aggressive project schedule to build the mine in one year. This was three months ahead of schedule and 7% below the original budgeted cost of C$123.5 million (US$86 million). The Mount Polley Mine was the first of a crop of new open-pit mines in British Columbia. The Mount Polley deposit has been explored since the mid-1960s when it was known as the Cariboo Bell property. From 1988, Imperial Metals completed drilling and metallurgical testing on the deposit. This led to a positive feasibility study and the issuing of a Mine Development Certificate in 1991. The project was later shelved due to falling metals prices and the strength of the Canadian dollar. In late 1994, Imperial merged with Bethlehem Resources Corp., bringing a strong project team to the company. The deposit was then re-evaluated, ore reserves revised and additional metallurgical testing was performed. The result was a revised project plan. It indi¬cated that a financially feasible gold-copper mining op¬eration could be constructed at Mount Polley operat¬ing at 18 kt/d (20,000 stpd). In May 1996, an agreement was reached with Sumitomo to jointly fund and develop the project. By early 1996, final plans and permits were being prepared for construction, scheduled to begin in June 1.996. On-site work commenced on May 28th, 1996 following lifting of the road restrictions. Mount Polley Mining acted as its own project manager. Construction was completed in June 1997. Plant runup took place in July and full production began in August. Through the use of off-site construction and the careful selection of contractors who cooperated to complete some 12 major contracts, it was possible to reduce the mine and mill construction time from 16 to 13 months. Off-site construction for all possible aspects of the work and the use of used milling equipment allowed significant savings in overall capital costs of construction. Total costs for the mine, mill and tailings dam equated to C$6,100/t/d of throughput. The mill design incorporates several innovative features that will aid maintenance and allow flexibility of operation. The operation is designed as a closed system and meets the latest environmental standards. Concentrate is shipped by truck to the port of Vancouver. Revenues for the mine come from the mine's production of about 3.1 t/a (100,000 oz/year) of gold and 10.8 kt/a (24 million lbs/year) of copper during the first four years of the 12-year mine life.

Jan 1, 1998

By A. C. Burr

This progress report covers the period from January 1949 to the end of the fiscal year, June 30, 1950. Three runs were successfully completed, and one run was terminated as the result of failure of a cast reaction tube. Including the abbreviated run, the gasifier was operated for 1,915 hours, during which some 428 tons of natural and steam- dried lignite was partly gasified In producing 20 million cubic feet of gas. Gas-production rates varied from 7.8 to 16.4 thousand cubic feet per hour, the latter being the highest production rate yet reached; hydrogen-carbon monoxide ratios of the product gas varied from 1.85, the lowest ratio yet produced, to 6.5; and heat-transfer rates through the heated wall of the outer tube varied from 2,100 to 4,400 B.t.u. per square foot an hour. The general objective of the project is to establish the technology and economy of the gasification of lignite in an externally heated, metal, annular retort. Specific objectives include determination of the useful life of the metal retort tube, which is a continuing problem, and special objectives that were established for each run as part of the systematic investigation of the basic variables of the gasification process. For runs 10 and 11 the special objective was the influence of the lignite feed rate on gasification; for run 12, a comparison of dried and natural lignite, and the production of gas having a hydrogen-carbon monoxide ratio less than 2; and for run 13, the influence of a gradually increasing steam rate with steam admitted to either the upper or lower reaction zones. In addition, during each run the sulfur distribution and concentration in the product gas and char were investigated. Experimental results obtained using the lignite feed rate as the variable indicated that the gas yield per ton of natural lignite varied inversely with the feed rate. Comparison of the gasification of natural and steam-dried Dakota Star lignite indicated that the dried lignite was a superior gasification material because: 1. The hourly gas production was higher at normal combustion space temperatures under nearly equal experimental conditions. 2. On the moisture- and ash-free basis, a considerably higher feed rate could be maintained at a relatively high percentage of carbon gasified. 3. At nearly equal moisture- and ash-free feed rates, the specific gas yield was higher. The location of steam admission was found to be important because the gas yield per ton of natural lignite was higher when at least a portion of' the process steam was admitted to the upper reaction zone. Heat balances showed the potential heat in the gas and char to be 71.8 to 83.6 percent of the total heat input. The sulfur concentration in the product gas was low, being in the range of 35 to 140 grains per 100 cu. ft., of which 1.5 to 2.3 grains was organic sulfur. Careful measurements and inspection of the 310-alloy rolled plate tube following runs 11, 12, and 13 showed no excessive corrosion; however, some radial deformation had occurred indicating that deformation or creep might be the limiting factor in the life of the tube.

Jan 1, 1953

By Eugie Kabwe

Rock bolts are components of tunnel support structures and their efficacy in reinforcement requires the appropriate estimation of the bolt pre-tension. However, cases of ineffective rock bolt application due to loosening are common which leads to the potential failure of the support structures, thus negatively affecting the tunnel stability. The effective employment of pre-tensioned bolt within support structures requires an appropriate installation tension as a result of sufficient bolt head/nut pre-load. Henceforth, this paper presents a load indicator washer (LIW) capable of withstanding assigned static loading as well as provides an appropriate pre-tension. The different LIW breadths are numerically analysed in the finite element code (ABAQUS) to estimate deformation when a designated 60-kN pre-load is applied. The numerical simulation employs a bi-linear isotropic hardening constitutive law governed by the von Mises yield criterion. The simulation also considers the nominal temperature of the nutLIW-rock bolt connection. Therefore, a long-term relaxation effect on bolt pre-tension as a result of stress relaxation is neglected. The compressive force required to achieve the LIW-predetermined deformation is the bolt pre-tension. It is drawn from the simulation results that the 1.5-, 2.0-, 3.0-, 3.5-, and 4.0-mm-thick LIWs are completely flattened when subjected to 28-, 42.5-, 65-, 76-, and 88-kN pre-load respectively.

By MARSHALL D. DRAPER

THERE are said to be about 150 operating companies in Kotchiu, most of these being small, corresponding in degree to lessees in western mines in the United States. Of the total number there are probably forty large companies having their own smelting plants equipped with one or two furnaces, slag crushing plant and other accessory equipment. A few plants, not more than ten, do custom smelting. There are in all about fifty smelting plants in Kotchiu. With little variation, the equipment and methods are the same. The plant usually consists of two furnaces, one being in operation while the other is being relined 01- re- paired. An adjoining house contains one or more of the large buffalo-drawn Chilean mills for crushing slag. A few houses for the working coolies, with more pretentious ones for the owners, complete the establishment, the whole being surrounded by a compound wall 8 ft. high.

Jan 1, 1931

Surface mining and reclamation of a southeastern Ohio site with sandstone-shale overburden resulted in (as compared to premining levels): 1) runoff volumes and peak rates that increased by a factor of from 2 to 10 during mining and after reclamation, 2) destruction of the "aquifer" perched on the underclay of the mined coal bed and gradual, but, as yet incomplete redevelopment of this aquifer after reclamation, 3) no immediate effect on another, lower perched "aquifer", 4) up to 100 times greater sediment concentrations in runoff. Results were influenced by increasing annual precipitation amounts through the period of record; 1978, 1979, and 1980 (postreclamation years) experienced precipitation amounts approaching or exceeding long-term normalcy for the area. Part of the reason that the site produced more runoff after reclamation than before mining is that the premine condition was one of an open, porous soil under woodland, while the postreclamation condition was one of a compacted, bulldozed soil. Sediment concentration results were influenced by failure of the postreclamation erosion control system and by a series of detention reservoirs above the stream monitoring station.

Jan 1, 1983

By Kelly E. G

NZ Steel's flushing slag typically contains 1.2 per cent V203. Extraction of vanadium from powdered slag using a salt (NaCI or Na2CO3) roast/leach process was investigated. With NaCl, optimum extraction conditions were a charge containing 10 per cent NaCI, roasting in air at 875°C for 4 hours, followed by leaching in dilute H2SO4. Extractions were typically 30-50 per cent. NaCI roasting did not chemically attack the slag; the phase transformations that occurred were due to high temperature oxidation. Slag particle size had a significant effect on extraction.Optimum conditions for extracting vanadium by Na2C03 roasting were 20 per cent Na2CO3 in the charge and roasting in air for 3-4 hours at 850-875°C followed by water leaching.Na2CO3 roasting involved chemical attack that resulted in the formation of perovskite (CaTiO3) and carnegieite (NaAISiO4).The extent of vanadium extraction depended on the amount of Na2CO3 added and the original slag SiO2 content.Compared to the separate roasting treatments, simultaneous treatment with NaCI and Na2CO3 gave lower vanadium extraction, while requiring considerably higher roasting times and temperatures.

Jan 1, 1982

By Diler Katircioglu-Bayel, Oner Yusuf Toraman, Safak Gokhan Ozkan

One of the most energy-intensive processes for producing submicron range calcite is stirred media mill. In the present work, numerous operating parameters such as solid mass fraction, grinding media size, media filling ratio, and grinding time have been investigated using a vertical type stirred media mill. The results are evaluated on the basis of mean particle size, specific surface area, and specific energy consumption. After conducting this study, optimum experimental conditions found to be as 70% media filling ratio, 25% solid mass fraction, 1 mm grinding media size, and 120 min grinding time. Besides, energy savings up to 22% were achieved with the choice of proper media size.