Search Documents

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By R. A. Puchner

The location of a decline shaft portal can have far reaching implications if the geotechnical conditions are not suited for safe and cost effective excavation. Ideally the portal should be positioned in an area where the excavation requires minimal support and the portal can be formed in reasonably competent rock. In many cases, however, the shaft is linked to an underground mining plan and the shaft may have to pass through poor ground conditions. Determining the optimal position at which tunnelling can commence i.e. the portal, is critical and requires a thorough geotechnical investigation. Methods used to acquire information for the assessment of the ground conditions are discussed in this paper. Selection of the appropriate methods is dependent on the anticipated ground conditions, the phase of investigation and restrictions due to site access and budget. Non-invasive techniques are often used during preliminary phases and invasive techniques for the detailed investigation. The methods used during each phase of investigation are discussed. Two case studies are then presented to provide examples of the investigative methods used in two different environments. The first being a flat featureless site with thick soils and deeply weathered bedrock, while the second is a mountainous site with differentially weathered rocky outcrops. Based on these cases, it is clear that an understanding of the geology and geomorphology of the site is vital to the final geotechnical assessment. Key words: Decline shaft, boxcut, geology, geomorphology, geotechnical, portal.

Jan 1, 2009

By B. J. Moore

This publication contains routine analyses and related source data for 278 natural gas samples from 14 States. All of the samples were collected during calendar year 1973 as part of a continuous survey of the free world for occurrences of helium in natural gas. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576.3 Fifteen previous publications have presented the results of 10,201 gas analyses prior to 1973. The first three, Bulletins 486,4 576,6 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1960. The other 12 publications,7 which were issued as information circulars, supplement the three bulletins and contain 4,983 analyses of samples collected since 1960. This publication is the 13th publication supplementing the three bulletins.

Jan 1, 1974

By William M. Knuth

This study involved a review of bonding and bond release practices in the states of the Eastern and Midwestern Coal Provinces. Data was collected from regulatory authorities and site visits to document the bonding and release procedures in the states related to achieving successful reclamation. The regulations related to PL95-87 were reviewed. The analysis included suggested modified or new bond release criteria, a review of applicable bond release inspection techniques was prepared, a conceptual graduated bonding system and incentive procedures for reclamation of surface mine sites to alternative or higher land uses. A number of conclusions and recommendations for further research were included. A detailed bibliography and a glossary are included in the report.

Jan 1, 1978

By H Esterhuizen, W Hartman

Rockfalls or significant deterioration of mine openings can have significant safety and financial impacts for mining operations. The failure of drives in underground mines sometimes highlight deficiencies in the mine risk management systems in detecting geotechnical hazards and to prevent events that can have significant impact. Consequences from these failures includes fatalities, injuries, loss of revenue, additional cost, and potentially a loss in Ore Reserves. Where the impacts are severe, it also affects families and communities linked to the operation. The assessment of underground excavations requires consideration of the full range and spectrum of geotechnical hazards, design aspects, ground support, layouts and sequences. Where the assessment of these are insufficient or incorrect, it can result in drive failures. Care must be taken that meeting production targets and personnel pressures do not result in a situation where production take preference over a proper risk-based assessment of the drives to be mined. The risk management approach is now widely accepted in the mining industry for the control and management of risks in underground mines. Codes of Practices (COP’s), Ground Control Management Plans (GCMP), Principal Hazard Management Plans (PHMP’s) and technical guidance documents has become the norm for describing the mines main hazards, risk levels and intimating controls for safe passage of vehicles and mine personnel. However, where there is a disconnect between these documents and what is actually being done at the mine site, the COP’s and/or Management Plans become ineffective (or vice versa). This disconnect may occur due to the actual content of these documents, a lack of resources, or a lack of understanding about the implementation. There is therefore a need for sites to have a documented and implemented risk-based approach for assessing underground mine development. This approach or system needs to identify all hazards and other factors affecting mine development stability early on in the design process, and outline the risk classification and controls required. This paper presents an amalgamation and modification of previous processes for a Geotechnical Risk Management System for Underground Mine Development. CITATION:Hartman, W and Esterhuizen, H, 2018. A geotechnical risk assessment tool for underground mine drives, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 235–253 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By Kenneth K. Landes

So far my consulting in industrial minerals has been confined principally to carbonate rocks,-salt, coking coal, and glass sand. Much of this work has been for companies either too small for a full-time geological staff or unaware of the value of employing one or more qualified geologists permanently. It gave me considerable personal satisfaction to see several of the latter companies employ one or two full-time geologists after the completion of a consulting contract with them. One possible reason why some companies lack the wisdom to hire geologists is that they are dominated by engineers who still subscribe to the old idea that engineers are self-sufficient in all fields. They could have learned this from their professors. I once knew a Dean of Engineering who got purple in the face when a faculty committee was discussing the financing of a broad gauged engineering project and suggestions were made that assistance be obtained from the Schools of Business and Law and from some of the science departments tie pounded the table and shouted "Engineers are trained to handle all this!" In teaching engineering geology some years ago I used to tell the class repeatedly that the course would not make them geologists, that the purpose was to teach them

Jan 1, 1972

By J. Pohlig

It is with more than ordinary pleasure that I have complied with the request of the President of the Verein Deutscher Eisenh?tten leute, to read before this meeting and in this country a paper on a system of transport by wire ropeways which, during the past twenty years, has advanced with rapid strides in Europe, and more partic ularly in Germany. America, with its immense network of railways and water communications, should offer peculiarly favorable oppor tunities for the introduction of these ropeways as feeders, more par ticularly in the mining districts, where, as in Europe, a hilly or mountainous region frequently opposes serious obstacles to the em ployment of surface railroads. The importance of the aerial ropeway as a factor in the develop ment of mineral resources deserves the consideration of every mining engineer. As a case in point, the rich iron-ore of the sierra de Bedar in southern Spain, would probably remain untouched to this day but for an aerial ropeway, 15.6 km. (9 3/4 miles) long, which con nects the mines with the shore of the Mediterranean near the town of Garrucha, affording cheap carriage to the nearest shipping point. A railway would have cost about $480,000 (£100,000), but such a heavy outlay would have more than absorbed all prospective profits on the sale of ore. As the aërial ropeway could be built for a little more than one-fourth of that amount, or $124,800 (£26,000), its erection furnished the successful solution of a profitable mining enterprise. This line has been in satisfactory operation for over two yearn; its details will be referred to later. But beside their importance as feeders, ropeways are valuable as a means of conveyance between works and distant warehouses, and between separate buildings in the same works. Their rapidly spreading introduction for such purposes indicates how keenly the necessity of effecting economies is felt under the stress of an everaccentuating competitiop.

Jan 1, 1891

By Gustav Jahner, Michael Baltrusch, Norbert Hoffmann

Near the port city of Whitby in the north-east of England, Anglo American (AA) is setting up the deepest mine in the UK, which will have a depth of 1,500m. The purpose of the project is to extract and transport polyhalite, both underground, and to market it globally. As part of the construction works, BAUER Technologies Ltd, the UK subsidiary of BAUER Spezialtiefbau GmbH, constructed three different shafts using the diaphragm wall technique, with depths of up to 120m. In order to ensure the specified vertical tolerance of maximum 200mm, several measurement methods were applied, and the results were documented in a 3D model. Complex de-sanding plant technology and specially developed polymer products were adopted to regenerate the trench supporting bentonite-slurry.

Sep 1, 2022

By T. Lane Carter

BEFORE describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, sary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor-that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work he spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the, resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Sep 1, 1908

By P Corbett, P Sheffield

Springvale Mine is an underground coal mine in the western coalfield of New South Wales which utilises retreat longwall mining technique. The mine encountered significant gateroad floor heave issues during retreat of LW415. Floor heave has subsequently impeded longwall advance as well as longwall bolt up and recovery to some extent during the extraction of the next five longwalls. Floor heave at Springvale Mine develops throughout the lifecycle of the mine roadways, and is most prevalent in longwall gateroads. Floor heave has been measured as early as 2 weeks after roadway development and continues to develop through the post-development phase, with a rapid increase in close proximity to the longwall face. This paper presents a case study of the evolution of understanding of floor heave behaviour at Springvale Mine based on geotechnical characterisation, an intensive convergence monitoring program (roof and floor movement) and spatial correlation of monitored locations with longwall face position. The analysis considers previously known factors contributing to floor heave including mining depth, geological and physical properties of the rock mass and mine design geometry. Investigation results indicate a strong correlation between floor heave magnitude and roof dilation magnitude, geophysically inferred faulting in underlying strata, areas of localised stress concentration and mine roadway dimensions. This paper also discusses the predictive model which was developed as a result of the study, which is now the basis of the floor heave removal program used to manage roadway convergence at the mine. Floor heave monitoring, prediction and management strategies (including floor reinforcement and removal) are also discussed. CITATION:Sheffield, P and Corbett, P, 2018. Managing floor heave in an underground longwall coal mine, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 78–94 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By L. C. Raymond

Good afternoon. I have entitled my talk "Investment for Progress," implying thereby a spark of friendly competition by private enterprise with such government-inspired foreign aid and investment programs as the Alliance for Progress. While the subject of foreign investment is hardly a new one, the perpetual flux of the political and economic surface of this earth we inhabit makes it forever timely and forever interesting. Especially do tremendous opportunities for international investment constantly present themselves to the mineral industry, and just as often must the industry approach these opportunities with a great deal of investigation and caution. This is not to say that the mineral industry--no less than any other industry--should be unenthusiastic about the foreign scene, but like everyone who proposes to put his money where his hope is, it should consider all the factors and weigh the possible disappointments as well as the rewards.

Jan 1, 1964

By D. Potter

Freeport Exploration initiated regional reconnaissance exploration programs in Irian Jaya, the easternmost province of the Republic of Indonesia in 1990 (see figure 1). Irian Jaya occupies the western half of the island of New Guinea. Freeport was awarded an initial contract of work which totaled 2.6 million hectares (6.4 million acres) and was subsequently awarded additional?concessions which added 1 million hectares (2.5 million acres). The concessions require work commitments and periodic relinquishments. Due to these relinquishments Freeport?s current land position totals l. 9 million hectares (4.7 million acres).

Jan 1, 1998

By Robert Hopler

THIS paper deals specifically with heading-driving as distinguished from the broader term tunnel-driving. A heading is a pilot or path-finder for the main tunnel. Some headings are complete tunnels in themselves; that is, conditions at times warrant driving a heading the full diameter of the proposed tunnel. A tunnel 10 ft. in diameter might be driven to advantage through a single heading, provided the nature of the material admits, but it usually pays to drive rock tunnels of large diameter through the headingand-bench system. Much depends upon the material, as in soft ground tunnels of much larger diameter are driven in a single heading.

Jan 1, 2010

By J. H. Rose

This paper describing the milling practice at the Magma Copper Co., Superior, Ariz., is one of a series being prepared by the Bureau of Mines on milling methods and costs in the various mining districts throughout the United States. ACKNOWLEDGMENT The authors wish to acknowledge their indebtedness to William Koerner, general manager of the Magma Copper Co., for permission to prepare this article; to J. S. Garrott, former mill superintendent, for the historical facts; and to Walter Cooksley, general foreman, for his assistance in obtaining the data.

Jan 1, 1930

By Laszlo Valentyik

Heavy media separation (HMS) is one of the most widely used gravity methods in the mineral industry. The feed is separated, according to the specific gravities, into two products; float (light) and sink (heavy) particles. The universal acceptance of the process is due to simplicity, efficiency and robustness for ease of control. However, if optimum separation is desired during the operation of heavy media plants, a delicate balance of a number of variables is essential. Among the variables, the two which are generally the most frequently checked and controlled are specific gravity and consistency of the medium. The latter is a function of the settling rate of the media. The medium is generally made up of finely ground ferrosilicon, magnetite, galena, shale, quartz sand, clay contaminants and water. The frequently present clay in the medium acts as a stabilizing agent, since the coarse heavy medium solids (called media) would quickly settle if they were mixed only in water. Clay concentration of the medium varies between 3-7% by height (1,2). Although clay is essential for reasonable media stability, clay concentration greater than 7-8% imparts too high a viscosity to the medium, and the feed cannot accurately stratify and therefore separate into the required products. To be on the safe side, plant operators clean the medium from most of the clays, and would rather work at a lower stability than have a very viscous medium on their hands. The most recent advance in the area of consistency control rlas made by the introduction of atomized (spherical) ferrosilicon (3). This extended the upper limit of the use of ground ferrosilicon from 3.3 to approximately 3.6, broadening the range of the optimum operating conditions. A viscosity control method was also worked out by the use of low cost additives which lower viscosity while retaining a favorable low setting rate (4). Recently (5) polymers have been successfully used in oil well drilling muds then the requirements were mainly to suspend and transport cuttings during the periodic shutdowns and dril1ings respectively. The rheological properties of these polymer suspensions are such that they present an infinite viscosity to

Jan 1, 1971

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

John Birkinbine, Philadelphia, Pa.: We have in the Institute two Dudleys—Dr. Charles B. Dudley, who has so thoroughly studied the chemical composition and physical behavior of rail-steel, and Dr. P. H. Dudley, whose investigations and

Jan 1, 1900

By W. W. Wen

A continuous pilot-scale test of the GranuFlow Process was conducted using a screen- bowl centrifuge for the dewatering and reconstitution of column flotation concentrate at a coal preparation plant in Virginia. In this test, a slipstream of the fine-clean-coal slurry from the column flotation concentrate was treated with a bitumen emulsion before dewatering. The treated products from the screen-bowl centrifuge appeared to be dry and in a free-flowing granular form, while the untreated products were wet, sticky, and difficult to handle. Specifically, test results indicated that the average moisture contents of the dewatered coal were 35.7, 35.5, 32.6, 29.9, and 26.5 wt% with Orimulsion additions of 0,0.7,3.2,4.8, and 6.4 wt%, respectively. The handleability and dust reduction of the dewatered coal product were also vastly improved.

Jan 1, 1997

By B. Fang

Electrochemical behavior of an X-80 pipeline steel, including frequency-sweep electrochemical-impedance spectroscopy (EIS), time-sweep EIS at a constant frequency and open-circuit potential (OCP) monitor, was investigated using four-point bending specimens subjected to a stress-corrosion cracking (SCC) test in a near-neutral pH environment, The capacitive loop became smaller with test duration, revealing an increase in the corrosion rate, The resistance obtained in the constant-frequency EIS test showed two regions, of which the region with a remarkable decrease in resistance transformed into a region of slow decrease, whereas the capacitance increased with test time indicating that iron dissolution was fast at first, and then a corrosion product or film formed and covered the surface, leading to the pitting formation.

Jan 1, 2005

By Keith K. Griffiths

Computers are a valuable tool to the aggregate industry and should not be overlooked. The selection of proper mechanical components is necessary. Merely the addition of a computer to operate a mechanical system will not guarantee that the system will work. Material delivery by rail or truck for stock-piling and intra-plant material transfer can be accurately supervised by automation with simplified controls for the layman to use. There are mechanical problems that occur in material blending and load-out systems when such a system is automated. Such things as material flow, bridging, stockpiling methods, overloading of equipment and safety must be considered. How these problems can be overcome by proper selection of compatible mechanical and computer equipment will be discussed. Also, there are many individual material circuits in a plant that can be computerized at a nominal cost. This type of computer installation will not necessarily result in increased production, but it will produce greater efficiency in manpower. These small computers, binary counters, memory circuits and other devices and their application to the aggregate industry will also be presented. A careful evaluation of the mechanical and computer inter-relationship by someone understanding both "Rocks and Electronics" is essential to proper handling of material by computers. Computers for the mining industry may be either digital or analog computers. Unless the computer is to control some type of chemical process, such as a cement plant, the, analog computer is not required and the digital computer' will be quite adequate and less expensive.

Jan 1, 1967