Search Documents

By Seoul National University, Ki-Ho Kim, Jong-Pyo Kim, Sung-Min Joo, Hee-Chan Cho, Hyung-Seok Kim

Aragonite was synthesized in addition of Mg2+ ion and SrCO3 seed by carbonation process, and the best condition and mechanism of the synthesis was studied by analysis of continuous pH change, ICP, XRD, and SEM. As MgCl2•6H2O addition increased, aragonite phase increased at condition of CO2 flow rate of 100 mL/min and stirring rate of 250 rpm. It was the dissolution of Mg(OH)2 that determined overall reaction time. As SrCO3 seed addition increased at 0.2 mole MgCl2•6H2O, the amount of aragonite increased and the aspect ratio was from 5 to 9. And it was thought that Mg2+ ion prohibited calcitetransformation of aragonite formed by SrCO3.

Jan 1, 2003

"The characterisation of resources and description of variability across different ore domains is key to accurate prediction of probable metallurgical performance. Such characterisation testwork often has limited drill-core from which to work and this immediately confines the characterisation method to smallscale. For flotation feeds, the JKMSI (Mineral Separability Indicator) is being developed as a potential characterisation tool, building on earlier work by Chudacek, (1990), which used shaken test tubes, and was called the EMDEE device. In addition, the consistency of flotation recovery for specified size fractions has shown to be preserved, irrespective of the amount of material in that size fraction obtained by different milling conditions, so that the overall recovery can be estimated from knowing the particle size distribution (McIvor and Finch, 1991; Bazin et al, 1994, Runge, 2007 and Wightman et al, 2010) The JKMSI unit uses less than 10 g of material per test in narrowly sized classes and results to date have demonstrated the value of the test. This paper discusses the potential of the test by demonstrating the link between JKMSI performance and mineralogy of five different ores from Laguna Seca, Escondida Minera Limitada as well as the correlation to plant scale performance obtained in an earlier survey (Coleman et al, 2006). Further work to tie down the proof of representatively of the small sample has been identified and is discussed and included in the paper. INTRODUCTIONSince the uptake of the flotation process at the turn of the twentieth century, small scale, laboratory methods have been sought to characterise flotation response. Although laboratory batch flotation tests are the most widely used method to evaluate reagents, characterise ore variability and obtain suitable model parameters using various scale up factors Runge (2101) other methods using less ore would be useful where ore samples were limited.A method using test tubes for testing ores’s flotation response to reagents was first developed by Ian Walk (Wark & Wark, 1935; Wark; 1938; Sutherland and Wark 1955). In these tests a 50 cc stoppered measuring cylinder served as a means for a qualitative experiment, the aeration being effected through violent shaking by hand. In these experiments about 10 g of mineral was ground by pestle and mortar under water after which the ground material was deslimed and adequately conditioned with the appropriate reagents."

Jan 1, 2013

By Ana Clara Petrucelli

A principal ferramenta de controle do processo BOF reside na regulagem do sopro de oxigênio. A análise dos parâmetros de interação entre o sopro e o banho metálico compõe o objetivo deste trabalho. Através de uma análise visual da penetração e fração volumétrica da bacia de descarburação, foi determinada a melhor configuração de sopro entre diferentes combinações de bicos multifuros (3 a 6 furos), distância lança-banho e vazão. Foram feitas previsões sobre a penetração do jato a partir de um balanço de energia a fim de validá-las com o modelo físico. As maiores penetrações foram alcançadas com os bicos de 3 e 4 furos, com a maior vazão e menor distância lança-banho dentre os padrões testados. Todavia, as maiores frações volumétricas da bacia de descarburação foram obtidas com 5 e 6 furos, vazão e distâncias variadas dentre as ensaiadas.

Jul 29, 2018

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002

By L. W. Higley

It is estimated that well over 20 million lb of chromium and 8 million lb of nickel, plus other metal values, are diverted annually to furnace dusts, mill scale, and contaminated swarfs in the domestic stainless and other specialty steelmaking industry. Little inroad has been made toward the in-plant recycling of these wastes to reclaim the metal values. The Bureau of Mines has devised a process for recovering about 90 pct of the chromium and molybdenum and well over 90 pct of the nickel and iron from stainless steelmaking furnace dusts, swarf, and mill scale. Other metals such as manganese are also recovered. Initial laboratory results were confirmed and expanded to include a wide variation of stainless steelmaking waste mixtures. Later experiments have included specialty steelmaking wastes other than from stainless steelmaking. Significantly, the ease of technology transfer has been demonstrated by a number of industrial-sized (19-ton) commercial electric furnace heats, in which the pelletized wastes represented some 10 to 20 pct of the furnace charge, replacing part of the normal scrap charge. Results of these successful large-scale trials are presented. Some information is also presented on incorporation into the pellets of chromium-bearing particulate wastes originating from other than steelmaking production. Cost evaluation indicates the process is economically attractive.

Jan 1, 1982

By Paul B. Valenti

The Nevada Moly Operation of Anaconda Minerals Co., (a molybdenum/copper ore body) was initiated in 1978, with a contract to Bechtel Civil and Minerals Inc. for construction of a mining and milling facility near Tonopah, NV. Ground was broken on the concentrator portion of the project in August 1979$ with a multi-phased startup of the mill beginning in June 1981. Processing design tonnage of 20 000 t/d (22,000 STPD) was reached in early 1982. Major pitfalls of rapid design and implementation of engineering, construction, and startup are considered. The operation of the concentrator including SAG milling, ball milling, bulk rougher flotation, copper/moly separation, moly regrinding and cleaning, thickening, and product loadout are discussed.

Jan 1, 1983

By R. A. Cattell

A technologic group such as the Petroleum and Natural Gas Division of the Bureau f Mines, which conducts research on many of the complicated and frequently interrelated problems f extracting crude oil and natural gas from the ground, transporting them to market or to daces for subsequent treatment, and manufacturing products, should report progress from time to time. Engineers and others who apply the results obtained by this division are closely associated with its personnel, because many of the problems are attached cooperatively with groups in industry. Some of this cooperation is formal, as exemplified by work now in progress under cooperative agreements with the States of Oklahoma, Kansas, and others, but much of it is informal, prompted by the desire to be mutually helpful in the public interest. Furthermore, the published reports of the Bureau on subjects pertaining to petroleum and natural-gas technology come to the direct attention of a relatively large number of persons, whose interest in results and appreciation of the value of this type of work have caused them to be kept currently informed regarding available data.

Jan 1, 1940

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

The Hill 50 Gold Mine is situated at Boogardie, 3 miles on a bearing of 295 degrees from; Mount Magnet township. Mount Magnet lies 300 miles north-north-east of Perth, Western Australia (Fig. 1).The older workings of the mine may be identified with those of Sirdar, Gold Mining Lease 696M The Sirdar had been worked before 1902 though no records remain, and irom 1903 to 1912 about a thousana tons at a grade of 6' 2 dwt. was extracted annually; by the end of 1918 6,225 oz. of gold had been obtained from the milling of 17,852 tons of ore. In view of these yields, and the length and width of the lode, this mine was early recognized as one of the most promising in the district. From 1919 to 1924 the ground,including G.M.L. 1282M, was held as Mt. Zion G.M.L. 1183M.The Hill 50 Gold Mine N.L. company took up the workings as Hill 50 G.M.L. 1282M in 1934 and have continued operations to the date of writing. To the end of 1956 the Hill 50 Gold Mine had yielded 982,106 tons of ore for a return of 448,'602 fine oz. of gold.The mine has been described by: J utson (1915), Feldtmann (1920), Johnson (1949), and Finucane (1953). Finucane (1953) details the mine structure to a depth of 414 ft. The author was able to examine the mine to a depth of 1305 ft. Detailed main level mapping to the 1060 level and a detailed surface examination have revealed aspects of the structure which were previously obscure.

Jan 1, 1960

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937

By Donald K. Sparling, C. Edwin Baker

The White Mesa uranium/vanadium mill is six miles south of Blanding, UT, on the Colorado Plateau, which has historically spawned more than 200 uranium mines. As uranium prices approached an all-time high during the mill planning period, Energy Fuels Nuclear Inc. anticipated the reopening of many of these mines, whose low grade ore suddenly looked economic. The company located the White Mesa mill close to these mines, to minimize hauling distances to the mill and give vendors added incentive to reopen or expand mine operations. A receptive local community, a relatively unencumbered trip through the regulatory maze, and some mill circuit innovations all helped to make the White Mesa mill a well functioning reality. From a strategic standpoint, and to begin ore stockpiling as early as possible, Energy Fuels constructed two ore buying stations and began receiving ore in early 1977. The buying stations were located at Hanksville and at what is now the Blanding mill site. Ore receipts at Hanksville did not materialize as anticipated and the facility has since been closed. The Blanding ore buying station is now an integral part of the milling operation. All ores, whether company, vendor, or for toll milling, are received at the Blanding station. The Blanding site was central to the plateau mines, and was well received by area residents, who encouraged the introduction of industry to the area. Residents viewed mill construc¬tion as an economic blessing and were prepared to accept the associated im¬pacts. Energy Fuels hired as many local people as possible for mill opera¬tions.

Jan 4, 1981

By Peter Bourke, Marc van Olst, Seppo Ronkainen, Natalie Brown

"Since the early days of flotation, process technicians have known that the speed at which the froth is recovered over the lip of the cell has a very direct and consistent influence on the grade and recovery of the circuit. No plant would deny that, even to this day, one of the most important aspects of a process technician’s job is ensuring that the froth is moving at a desired and controlled speed over the lip. Unfortunately, process technicians cannot watch the froth throughout the entire shift, as there are always a lot of other tasks to do.A considerable amount of work has thus been done to develop a “system” that automatically measures the speed of the froth. This measurement would then be used in simple controllers to emulate the steps taken by the process technician in correcting deviations of the froth speed from its desired level. Many of the earlier attempts to measure speed were ineffective, as they were unable to cope with turbulence on the froth surface. The FrothMasterTM instrument makes use of machine vision technologies to measure the speed of the froth over the lip of a cell at a very high sampling rate. This instrument produces an extremely reliable and accurate measurement of the froth speed (as well as other parameters such as bubble size and froth stability). As we will show, the effectiveness of the speed measurement in controlling the performance of the plant is a testimony to its reliability.Three FrothMasterTM units have recently been installed on the Cadia Hills Gold Mine in New South Wales (Australia). The objectives of this installation were:To control the mass-recovery of two Tank Cells in series on the same level where differences in the hydrostatic head between the two cells result in the cells pulling inconsistently with respect to each other.Control of the concentrate grade (%Copper) from the first rougher.Reduction in the frother consumption in the rougher circuit by monitoring the froth speed.A simple controller was designed to react to disturbances in the same way that human operators react. This was done after consultation with the metallurgists and the process technicians at Cadia. The controller had two functions:Stabilisation: The stabilising controller made use of three manipulated variables (level, frother addition rate and aeration rate) to control the froth speed to a setpoint.Optimisation: The optimising controller adjusted the froth speed setpoint based on deviations of the grade (measured in real-time with an OSA) from a setpoint. The plant metallurgist adjusted the grade setpoint based on information about the ore."

Jan 1, 2001

This paper endeavours to lay as concisely as possible, before the members the salient features of local gold milling practice, and to point out in what respects this practice differs from that of other large mining camps. This is essentially a free milling ore the gangue being quartz and the gold occurring in a coarse form. At times the ore crushed contains a good deal of slate, the latter imparting to the tailings a somewhat leaden hue.Small amounts of sulphides, chiefly iron pyrites, and at times smaller quantities of arsenical pyrites, zinc blende, and galena are contained in the stone. The average amount of sulphides contained in the ore cannot well be ascertained, as the concentrate obtained in all cases contain too much silica to form a basis of calculation...

Jan 1, 1902

By Andrew St. Amant

This report reviews the first three "investigative and concept generation" phases of the referenced contract, and details task performance of Phase IV. This last phase integrated the most promising concepts from Phases I, II, and III into a prototype detailed design which was manufactured, and then tested on a mine locomotive. The concepts developed during the first three phases provided "Improved Pole Tracking," automatic "Rapid Pole Retraction" in the event of dewirement, and servo-operated "Remote Pole Repositioning" on the trolley wire. The Appendix of this report supplies detailed information for the design and construction of the prototype system which is comprised of an RCB (Remotely Controlled Base subassembly), an RCL (Remote Control Lever subassembly) and an SAU (Servo Amplifier Unit) subassembly.

Jan 1, 1980

By Ebrahim Ghasemi, Mohammad Hossein Kadkhodaei, Mosareza Jalilian

Entry-type mining methods, such as cut and fill method, play a significant role in underground mining, and they are still suitable methods for extracting deposits with irregular shapes and with weak host rocks. In these mining methods, the stability of the open spans is important for improving worker safety and increasing ore recovery. This study focuses on the application of six data mining classification methods, namely multinomial logistic regression (MLR), classification and regression trees (CART), logistic model tree (LMT), decision tree (J48), multivariate adaptive regression spline (MARS), and gene expression programming (GEP), in order to develop predictive models for stability assessment of underground entry-type excavations. For this purpose, a database containing 399 case histories of entry-type excavations from seven Canada underground mines was used. These models predict the stability status of entry-type excavations based on two input parameters, dimensions of the span and rock mass rating (RMR). The performance of developed models was evaluated using six performance metrics namely accuracy (ACC), sensitivity (SE), precision (PR), Matthew’s correlation coefficient (MCC), area under the receiver operating characteristic (ROC) curve (AUC), and performance index (PI). The results showed that all developed models can be used to predict the excavation stability, but the comparison of models indicated that the J48 model provides the highest performance with ACC = 0.900, SE = 0.869, PR = 0.922, MCC = 0.835, AUC = 0.891, and PI = 4.417. Thus, the proposed J48 model can be applied to identify the susceptibility of span instability in the entry-type mining, and if instability has been predicted, the necessary measures, including the use of suitable support systems, can be considered to reduce the casualties resulting from span instability.

Feb 26, 2024

By L Manca, P B. Hills, D Tyler, N Pollington

This paper describes a collaborative project undertaken by Newcrest Mining Limited (Newcrest) and pitt&sherry to identify, develop and then implement global best practices to manage the exposure to inrush (dry and mud) hazards in underground mining operations. An extensive literature review was undertaken to identify past experience globally and the current state of knowledge and practice in managing inrush hazard. A key requirement of the literature review was the development of a list of guiding questions which would form a framework for approaching operators to discuss the topic, capture recent learnings and understand current operating practices to allow the development of a best practice solution. An initial cohort of 14 mines across four continents chose to contribute and detailed interviews were carried out by the project team. The outcome from the literature review, interviews with participating mines and various internal discussions was a comprehensive summary document detailing Basic versus Best Practice management of the inrush hazard. This document is being used as a gap analysis tool by Newcrest to assess and guide the management of inrush hazard at their existing and future operations. The summary document has also been provided to the participating mines for their consideration. The project is iterative and will continue to evolve as new experiences, knowledge and practices come to light.

Mar 15, 2021

By T. Sun, J. Kou, D. Tao

"The reduction behavior of low-grade lump hematite ore (100% 20-50 mm) has been evaluated by performing a series of coal-based direct reduction roasting tests followed by magnetic separation under different process conditions such as roasting time, temperature, reductant type and dosage, and grinding stage. To investigate mineralogical transformation and reduction characteristics of lump hematite ore, roasted ores and magnetic concentrates were analyzed by X-ray diffraction (XRD), scanning electron microscopy (SEM) with energy dispersive spectrometer (EDS) and polarizing microscope. The results have shown that a magnetic concentrate with a total iron (TFe) grade of 90.7% was produced at an iron recovery of 83.9% when lump hematite ore was reduced at 1,200° C for five hours using 35% lignite as a reductant followed by two stages of grinding, for 20 min and 30 min each, and low-intensity magnetic separation. The degree of reduction is closely related to the change in the internal structure of the roasted ore. Lignite with a higher fixed carbon content and lower ash generated roasted ore with a more highly porous structure, which provides better permeability of reducing gas. Magnetite, fayalite and wustite were the dominant intermediates of coal-based direct reduction of lump hematite ore. Parts of wustite reacted with SiO2 or Al2O3 in gangue and generated fayalite or hercynite. FeO in fayalite was replaced by CaO to produce wustite, which was finally reduced to metallic iron. However, Fe in fayalite and hercynite produced with low contents of CaO cannot be reduced into metallic iron. Introduction Low-grade hematite ore, characterized by low Fe content and high SiO2 content, cannot be treated by traditional mineral processing methods due to its nonmagnetic property and fine liberation size. The direct reduction (DR) roasting process has been studied and proven satisfactory in treating difficult-toprocess ores, such as low-grade nickel laterite oxide ore (O’Connor et al., 2006; Cao et al., 2010; Guo et al., 2011), high phosphorus oolitic hematite ore (Li et al., 2012; Yu et al., 2013), low-grade hematite ore (Wei et al., 2013;) and iron ore tailings (Li et al., 2010), which greatly expand the resources of usable iron ores (Srivastava and Kawatra, 2009). Therefore, the use of a DR process to treat low-grade hematite ore to produce direct reduced iron (DRI) is of great interest to many researchers of mineral processing and metallurgy (Weissberger et al., 1986)."

Jan 1, 2015

By J. W. Givens, P. B. Crawford

A potentiometric model study has been made of the effect of vertical fractures existing in the matrix of the reservoir on the flooding or cycling performance. Fractures can have unusual flow characteristics. Fluid entering one side of a fracture can emerge on either the same or opposite side of the fracture, depending on the particular streamline. Fracture orientation has a great influence on the sweep efficiency. However, sustained fluid injection may still permit large areas to be swept. INTRODUCTION One can find considerable information available in the literature on the effect of fractures originating at the wellbore on sweep efficiencies of water-flooding or gas cycling programs.1-5 However, there arc few, if any, quantitative data reported in the literature on the effect of vertical or horizontal fractures existing out in the reservoir matrix on secondary recovery performance. Several papers have been presented on the effect of vertical and horizontal fractures on the productivity or conductivity of waterflood and gas injection patterns, but in all cases the fractures initiated at the well and simulated commercial fractures.6,7 It is believed that natural fractures may exist out in the reservoir matrix and would effect the displacement performance. The purpose of this report was to study the effect of a few isolated vertical fractures existing out in the reservoir matrix on the performance of waterflood or gas injection patterns. DESCRIPTION AND EQUIPMENT Since the potentiometric model was described by Lee8 it has been widely used to study numerous types of fluid displacement problems. The potentio- metric model can be used for fluid displacement studies when the following assumptions are valid: (a) steady-state conditions exist; (b) the mobilicy ratio is one; and (c) the capillary and gravitational effects can be neglected. Five-spot and direct line drive square patterns were studied using a copper strip of the desired length and orientation to simulate a vertical fracture in the reservoir matrix. The 20 x 20-in. model was considered to represent only one element of an infinite array of similar patterns. DISCUSSION AND RESULTS FIVE-SPOT PATTERN — ONE FRACTURE BETWEEN INJECTION AND PRODUCING WELLS Fig. 1 shows a quadrant of a five-spot pattem with the vertical fracture existing out in the matrix along a line connecting the injection and producing wells. Length of the fracture was equal to 35.4 per cent of the distance between injection and producing wells. In this particular pattern it is noted that fluid breaks through from the injection well to the producing well when the dimensionless time is equivalent to 26.9. Dimensionless time is defined as volume of fluid injected divided by the volume of displaceable fluid in the pattem expressed as a per cent. The cross-hatched areas of this

Jan 1, 1967

By Harry K. Weatherbee

The paper presents a design case study for a four-story correction facility addition in south Boston, Massachusetts, supported on friction piles driven into the Boston Blue Clay. 356 mm (14-in.) square prestressed-precast (PSPC) concrete piles were selected as they were found more effective and economical. A static load test was performed where the pile was brought to "failure". The load test data were evaluated to estimate the Ultimate Pile Capacity as well as the Ultimate Unit Skin Friction (Adhesion) to serve as a design tool for friction pile projects in the south Boston Area.

Jan 1, 2003

By R. A. Westin

[Polychlorinated biphenyls (PCR's) have been widely utilised as fire-resistant dielectric coolants; in electrical equipment used in mining applicants, including transformers, capacitors, electric motors, and electromagnets. In addition, PCB's have been used in hydraulic fluids and heat-transfer fluids and are present in many oil-filled transformers. The U.S. Environmental Protection Agency (EPA) recently banned the manufacture of PCB's and equipment using PCB's, and imposed strict requirements on the continued use and disposal of existing PCB equipment. This manual discusses the EPA requirements, suggests ways to decrease the risks resulting from continued use of PCR equipment, and surveys the non-PCB equipment that is available as replacements for the PCB electrical equipment presently used in mines.]

Jan 1, 1980