Search Documents

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By M. A. Trevits, J. E. Urosek, A. C. Smith, M. P. Valoski

The National Institute for Occupational Safety and Health (NIOSH), in partnership with the Mine Safety and Health Administration (MSHA), is conducting research to test, evaluate, improve or modify coal mine fire-fighting strategies and methodologies through large-scale tests. Since wood is the second most abundant fuel available during a coal mine fire, it was decided that series of large-scale wood crib fire tests were needed to measure the products of combustion and to observe the capability of commonly available direct application fire suppression equipment, namely, fire extinguishers, water and gas-enhanced foam. This paper discusses the wood crib fire tests, provides insight into the products of combustion and describes observations made during the application of the fire suppression agents.

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By S. Underwood

The tracer gas method of conducting ventilation surveys is a means of determining air quantity in underground mines with knowledge of the concentration of the tracer in the atmosphere and the flow rate at which the tracer is being released. The technique is useful in inaccessible areas of underground mines and areas where traditional point measurement of velocity is not practical. Sulfur hexafluoride (SF6) is the industry standard tracer(Kennedy 1987) used in underground mines because it is safe, stable, and not naturally occurring in the mine environment. The implementation of a second tracer will increase the versatility of the tracer gas technique allowing for simultaneous releases for the study of interrelated ventilation circuits, and for conducting multiple experiments in less time. This paper will detail the selection of perfluoromethylcyclohexane (PMCH) as a novel tracer with sensitivity, physical properties, and analysis characteristics similar to SF6. Methods for the release of liquid PMCH into underground mines will be recommended, and the vulnerabilities of sample loss due to condensation of vapor PMCH will be explored. Finally, the benefits and implications of using PMCH as a second tracer will be discussed.

Jan 1, 2012

A series of electron beam, cold hearth, single melt Ti-6Al-4V plates (nominally 2.5 cm thick) impacted by 2cm diameter, 4340 steel projectiles (with 54g nominal mass) at velocities ranging from 0.633 to 1.027 km/s were sectioned along the impact axis and examined by optical metallography to characterize the formation, growth, and microstructure of adiabatic shear bands. Near ballistic limit velocities, the shear bands propagate towards the rear of the target where they coalesce and grow to provide a cylindrical solid state flow regime for the plug volume.

Jan 1, 2006

By Fernando Aracati Botelho, Jose Antonio Silva Souza, Luis Alves Venancio, Emanuel Negrão Macedo

"1 AbstractThe production of alumina from bauxite using the Bayer process generates 0.7 to 2.0 ton of the residue known as red mud and about 800 kg of CO2 per ton of alumina. The direct use of exhaust gases to react and neutralize the bauxite residue may allow a double gain: open a wide range of new applications for bauxite residue reducing its reactivity and sequester from 3 8 to 107 kg of CO2 per ton of alumina. This paper shows a pilot scale reaction of a suspension of bauxite residue-water with flue gas produced from direct burning oil, similar to the exhaust gases of a refinery. Two different types of reactors are used, a spray tower and a packed column. The inlet and exhaust gases are analyzed using electrochemical cells and non-dispersive infrared sensors. The pH of the suspension is monitored during the reaction and after to evaluate the buffer effect. 2 IntroductionThe production of millions of tons per year of alumina around the world generates from 0. 7 to 2.0 ton of the residue known as red mud (RM) per ton of alumina. The vast majority of the red mud is stored in large sealed lakes. Due to the high reactivity this material is considered dangerous and currently there is no operating process capable of reusing all the material produced at any refinery. These lakes after filled of solid material eventually have the surface revegetated [4]. In any case they will remain as an environmental passive and needs monitoring for decades. The search of a industrial process that combines the reduction of the CO2 emission and the reduction the pH of the red mud opening the possibility of large scale and economically viable ways is the main objective of this work.The use of the exhaust gases of the refmeries to neutralize the bauxite residue may allow a double gain: Open a large array of new applications for the residue with the reduction of its reactivity and sequester millions of tones ofCO2 plus other gases like SO2 [7] and NOx. This project studies the reaction of the exhaust gases from a boiler burning diesel with RM in different reactor types and conditions in order to obtain parameters to design equipment capable of process this reaction on a larger scale. With these objective compositions of red mud were processed with flue gas at concentration similar to the exhaust gases of the calcination process and boilers of the refmeries."

Jan 1, 2012

The Energy Authority of NSW has wide powers and responsibilities conferred by its Act which are pertinent to the State's coal industry and its development into the next century. With respect to coal, the broad objective is to maximise the benefits to NSW and its people derived from the State's coal resources. The initial focus of the Authority's coal-related activities in the late 70's and early 80's was on petroleum substitutes from coal. Research was supported, especially on hydrogenation, and the Authority participated in the Joint Australia/Federal Republic of Germany coal-to-oil feasibility study. It also co-ordinated a State Government initiative to involve the private sector in examining the possible establishment of a synthetic fuels industry based on Hunter Valley coal. With a short-fall in world-wide petroleum supply now seen as less likely for some years, the Authority is looking also at ways of working towards the broad objective in the field of coal utilisation on both domestic and export markets. Areas of interest include possibilities for using washery rejects, means of making NSW coal more competitive as an energy source, use of coal-seam gas and new or special technologies for burning coal. The future is expected to see renewed interest in producing petroleum substitutes, and coal - as the State's major energy resource - is seen as a strong contender as a basis for such an industry. Developments in coal-based power generation are also expected to have an impact, with advanced technologies having a possible place here as well as Overseas.

Jan 1, 1987

By R. E. Wilmot

The problem of corrosion of reinforcement in concrete structures is internationally recognised and represents the single biggest expenditure in the preservation of steel reinforced concrete structures. While the corrosion protection of the reinforcing steel is no substitute for design and the placement of good quality concrete, it does provide for a viable and economical extension of structural integrity and service life in the day-to-day and practical environment in which concrete structures are constructed. The mechanism of corrosion attack and consequent deterioration of reinforced concrete structures is well understood and documented. New structures can be designed and built to withstand corrosion. However, due to short-term economical restraints, many new reinforced concrete structures continue to suffer as a result of corrosion damage, which results from the corrosion of the steel reinforcing. This paper explores the economic and practical benefits offered by the application of hot dip galvanizing as a viable means of protecting reinforcing steel concrete structures. The paper also discusses technical misconceptions that exist with respect to the application and performance provided by the use of hot dip galvanized reinforcing steel.

Jan 1, 2006

Much attention in controlling blast vibrations has been centred on the probability of causing damage to structures in the area adjacent to where blasting is carried out. In most cases these structures are residential properties and the effect of the vibrations on the occupiers has not been studied to any great extent. This paper looks at the sources of disturbance caused by blasting and their psychological effect. A comparison of ground vibration levels for compliance is examined within the framework of structural and human response.

Jan 1, 1998

By W. D. Mcmillan

Important reserves of nickel ore occur in the Levies district in Oriente, Cuba. The area is mountainous and mostly covered by heavy vegetation. The ore bodies comprise surface tracts of nickeliferous laterite underlain with decomposed serpentine of ore grade. The Cuban Nickel Co., a wholly owned United States Government corporation, owns a plant for leaching the nickel from its ores at Nicaro, Oriente, Cuba, Between December 1943 and March 31, 1954, 5,902,225 short tons of ore was treated, with a recovery of 116,206,519 pounds of nickel (52,711 metric tons). In 1953, 1,330, 224 short tons of ore was mined and 27;"3,129 pounds of nickel produced. The Cuban Nickel Co. also owns a townsite, with the necessary facilities, mining equipment, and 11 miles of railroad. Ore for the plant has been produced from the Ocujal-San Juan claims on lends owned by the Nicaro Nickel Co., a sub¬sidiary of Freeport Sulphur Co. The Government enterprise is man-aged by the Nickel Processing Corp. The Cuban Nickel Co. has denounced mineral concessions and has purchased other claims from private owners.

Jan 1, 1955

By A Bennett, A Peck

BHP has recently constructed a Hot Briquetted Iron Plant at Port Hedland in the Pilbara region of Western Australia. Supply of iron ore fines to the plant is by conveyor from the companyÆs existing Nelson Point stockyards. The conveyor passes under Port Hedland harbour in a concrete segmentally lined tunnel, approximately 1030 m long and with a 5.1 m external diameter. The tunnel was constructed by a Tunnel Boring Machine (TBM) which both excavated the ground and erected the tunnel lining. The tunnel was bored between cut and cover in situ concrete portal structures, the TBM being launched from the Finucane Island side towards Port Hedland town. The alignment required lengthy gradients of 1:6 on either side of the harbourÆs dredged channel, under which the tunnel is bored with a minimum clearance of 8 m.The tunnel is fitted-out with:1800 mm belt conveyor capable of 10 000 tph;walkway along which a specially designed inspection/ maintenance vehicle can run; andtunnel services including power, light, fire detection and suppression communications, water mains for wash down and sumps and pumps for drainage.This paper gives a general overview of the design and construct contract, important aspects of the design and the construction process itself.

Jan 1, 1999

By B Beale

Bow-tie analysis is a commonly used tool to identify and display risks that have the potential for an undesired hazardous event. The output of the analysis are bow-tie diagrams, which are an effective and versatile communication format that can be applied to any type of risk. Contrary to their simplicity, a proper bow-tie diagram that maintains its usefulness and clear communication is difficult to build. Over two decades assisting Major Hazard Facilities with bow-tie analysis for Safety Cases, several common mistakes have been identified. This paper aims to highlight those issues with examples and provide improvement strategies. A sample of the most common mistakes are: - overly complicated risk analysis - poorly scoped and defined terms - poor descriptions and justifications - identifying too many dependent controls. Overly complicated risk analysis leads to wasted time in obtaining data for little gain. The bow-tie diagram is only a model. Effort should be redirected into identifying and managing controls that will make a tangible difference to site risk. Broad scopes lead to enormous and confusing bow-tie diagrams for both the user and the workshop team. Defining the scope of the study, the consequence severity of interest and critical control characteristics creates focused workshops and targeted analysis. With more definitive scope, there may be more bow-tie diagrams, however, they are succinct and specific. Well described causes are imperative for clear communication to users, regulators and future bowtie review workshop groups. It is best to use common wording structures and explain the event stepby- step. Also, clearly document any likelihood calculations and use data references where applicable. Identifying all possible controls creates a false sense of security that there are many layers of protection. In reality, most controls are dependent on a single system or person and could all be compromised from a single failure. A definition of a ‘bow-tie’ control is required whereby it must be independent from other controls. Improving the bow-tie analysis process will assist operators in developing meaningful and ‘operational’ bow-tie diagrams to support risk management systems and practices.

Apr 16, 2024

By F. S. Wartman

The presence of magnetite, either dissolved or suspended as solid crystals, in slags from the copper reverberatory furnace is a frequently mentioned cause of an abnormally high copper content in those slags. The presence of this oxide in the slag is to be expected, since it is present in appreciable amounts in both converter slag and roaster calcine which comprise a considerable proportion of the furnace feed. Magnetite is also a product of some of the furnace reactions. These abnormal losses result in several ways. Magnetite is supposed to favor the formation and retention of copper ferrite, in the slag. Crystals of solid magnetite suspended in the slag are objectionable-because they make the slag less fluid and often entrap globules of matte. Frequently these crystals settle into a layer at the slab-matte interface which may have such mechanical strength as to create a false bottom and interfere with furnace operation by preventing separation of matte from slag. Magnetite may, by crystallizing on the furnace bottom, build the bottom to such a level that the furnace can no longer be operated.

Jan 1, 1928

By T. W. Wlodek

"AbstractThe results of research into the fatigue properties of SAE 1080 carbon steel and nickel-chromium-molylbdenum steel for mining drill rods are analysed and described in detail.The effect of water corrosion on the fatigue strength of drill rods of these two steels in the as-rolled condition has ,been investigated and the beneficial influence of shot-peening on their dry and water-corrosion fatigue strengths determined by employing the method developed previously (1).Eight S-N curves for as-rolled and shot-peened mining drill rods under both dry and water corrosion conditions have been derived and their shape and relative position are discussed. The main features relating to field performance of the drill rods are analysed.Purpose of Research and Outline of ProgrammeDRILLING holes in rock and ore by means of drill rods attached to a pneumatic drill is a basic procedure required in mining operations. Detonation of explosives placed in these holes is at present the only practical method of breaking down the rock and ore.A drilling rod is supported by its bit end in the drilled rock. Its shank end, fixed in the drilling machine, transmits impact energy to the cutting edges of the bit. On the field performance of the drill rod depend a number of basic mining operations such as sinking, drifting, and stoping. The drill rod is there-fore regarded as one of the most important tools used in the mining industry."

Jan 1, 1952

By V. Bari?ic

The scheduled power cuts of early 2008 were a disturbing reminder that South Africa needs to expand its power-generating capacity. Low-grade and discard coals, of which South Africa has much, are a source of energy and amenable to combustion in circulating fluidized beds (CFBs). Foster Wheeler (FW) has a long record in developing this technology in boilers. The technology is flexible in burning a variety of fuels; low-grade, high-ash coals, good quality bituminous and anthracite coals, and biomass and waste fuels have all been used. CFB boilers are efficient, reliable and can be designed to meet tight emission standards. In recent years once-through supercritical (OTSC) CFB technology has been developed. It enables the next stage in CFB development to proceed to a medium-scale (500 MWe) utility in such projects as Lagisza, which runs at a net efficiency of nearly 44%. Scaling the technology up to 800 MWe with a net efficiency of>45% is planned to be commercial during 2009. CFB technology can reduce CO2 emissions in the repowering of coal-fired and greenfield power plants. It does so through greater efficiencies and by co-combusting coal with biomass. FW has also developed CFB technology for the gasification of biomass, as, for example, in a pressurized gasifier to produce syngas, which can be used for the production of biodiesel, thereby reducing CO2 emissions from vehicles. Carbon capture and storage (CCS) can potentially cut CO2 emissions in the generation of power from fossil fuels in the short term, provided that it gains public acceptance, that the required regulatory framework is created, and that emission-trading mechanisms or other incentives provide a solid return on the major investments required. Oxyfuel combustion is an option in CCS; Foster Wheeler is adapting its CFB combustion technology for oxy-fuel combustion to meet this challenge. It is developing Flexi-burn?, which enables a plant to be operated either with or without carbon capture. This paper describes the status of CFB technology in terms of boiler efficiency and fuel flexibility. It highlights the advantages of CFB technology for oxyfuel combustion, presents a development plan for Flexi-burn?, and discusses a pressurized gasifier for biodiesel applications.

Jan 1, 2009

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By H. Stutchbury

Alberta is labouring, and has laboured, under serious difficulties in the marketing of ?her coals, due to a number of conditions which now obtain, but all of which appear capable of solution, and their elimination would insure a very largely increased market for the vast coal resources of that province. It is perhaps necessary to again mention the fact that 15 per cent of the world's coal resources are to be found in Alberta; 21 per cent of that of North America; 72 per cent of that of the British Empire, and 87 per cent of that of all Canada. While we talk largely of the great wealth of Canada, the immensity of her vast natural resources, it is axiomatic that the mere presence of any natural product in a country does not in itself constitute wealth for that country, unless these raw materials can find a market, either in their raw state, or by the process of manufacture. There are many factors, however, which enter into the marketing of any commodity. The chief of these, in my opinion, is price competition. High costs of production materially reduce the radius in which any product can be marketed, and this applies particularly to coal. Mining costs in the province of Alberta are necessarily high at the present time, due in a large measure to the ease with which the 'gopher hole' mine can be opened with small capital.

Jan 1, 1925

By B. A. Day

The traditional view taken of commodity prices is that they are cyclical, with strong demand boosting prices and attracting new suppliers. The resulting increased supply pushes prices down with consequent exit of the higher cost producers. And so the process repeats itself. Little attention is given to shifts in underlying global issues and their effect on the traditional process which is seen as being controlled by ?amorphous? market forces with producers profiting from the good times and trying to survive in the bad.. The questions posed are: does this still apply and will it apply into the future? What new factors are affecting the cycles? Can we expect to find the traditional commodity cycles repeated in the 21stcentury? Are producers powerless within the forces of the cycles? Forces likely to affect future commodity prices will be suggested, using gold, zinc, copper, tin and coal as case studies. The long-term downward trend in the real price of commodities is identified.

Jan 1, 2000

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By Ira B. Joralernon

THREATS of a coming metal famine in the United States have filled many columns in magazines and newspapers in the past three years. This asserted menace has diverted attention from the actual results of recent exploration. Because no one had bothered to look into the facts, the statistical experts assumed that little ore was being found. They often subtracted the staggering tonnage of metals produced during the war from earlier published reserves, and assumed that the difference was all we had left. Naturally, they shuddered, with all possible publicity. For their figures showed an imminent lack of nearly all the metals needed for an industrial civilization, as well as for mechanized war. They concluded that only wholesale imports and development and production of metals by Federal agencies could avert the famine.

Jan 1, 1948