Search Documents

By C. N. Adams

The purpose of this investigation was to evaluate the physical and mechanical properties of high-purity titanium made by two processes. Sodium-reduced metal with 58 Brinell hardness number (B.h.n.) and electrorefined metal with 60 B.h.n. and 70 B.h.n. were used. Titanium of these hardness levels did not work-harden excessively, and beyond 40 percent cold work the hardening effect was not great. Rapid softening occurred when the metal was annealed at temperature between 300° and 600° C. Full annealing, as determined by property and microstructure studies, was accomplished after 30 minutes at 700° C. A recrystallization diagram is presented which is based on determinations of annealed grain size as a function of rolling reduction and annealing time. For reductions of less than 20 percent, exaggerated grain growth occurred during annealing; for reductions greater than 20 percent, the variation in grain size for each annealing temperature was minor.

Jan 1, 1961

By Mizraim Uriel Flores, Elia Guadalupe Palacios, Sayra Ordoñez, Iván Alejandro Reyes, Ister Mireles, Martín Reyes, Francisco Patiño, Hernán Islas, Víctor Hugo Flores

This paper presents the characterization of a sample of mercury jarosite that was synthesized by slowly adding Hg(NO3)2H2O into a Fe2(SO4)3nH2O solution. X-ray diffraction (XRD) analysis performed on the sample confirmed that the compound presents a crystal phase corresponding to mercury jarosite. Analysis through Scanning Electron Microscopy with Energy Dispersive X-ray Spectroscopy (SEM-EDS) determined that the precipitate is composed of mercury, sulfur, iron and oxygen. It is made up of spherical particles with an average size of 38 μm; these particles are made of rhombohedral micro-crystals with sizes ranging between 1 and 2 μm. Chemical characterization was performed through dichromatometry analysis, gravimetry and atomic absorption spectroscopy (AAS), thus obtaining the following composition: 27% Fe3+, 37% SO4 2− 14% Hg2+, 22% OH− + H3O+ + H2O. The following approximate formula of the compound was determined from chemical analysis: [Hg0.39(H3O)0.22]Fe2.71(SO4)2.17(OH)4.79 (H2O)2.09.

Mar 1, 2017

By Susan M. Moore

Many challenges are faced by workers in lower-seam (42 inches or less) mines. The lower-seam heights confine mine workers to their knees as they perform their daily tasks such as installing roof bolts, delivering supplies, repairing belt, or cutting coal. Miners working in these lower seams often consider kneepads to be their only line of defense against knee injuries. However, healthy knees do not start and stop with kneepads. Other interventions such as changing postures, proper hygiene, and work station design may also be used to reduce mine workers? risks for developing knee injuries. Incorporating these and many other interventions into a mine worker?s ?way of life? is an important step to ensuring a long, healthy career and retirement. Keeping knees healthy is also a key aspect to reducing costs in low-seam mines as the industry battles rising health care costs, and training/recruitment of replacement workers is time-consuming and costly. Educating the workforce about the possible interventions to reduce knee injury risk is a primary objective for the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Laboratory (PRL). Therefore, NIOSH researchers, along with industry and academia, developed a training package to educate the mining community about some possible interventions beyond kneepads that may be used to help decrease knee injury rates. Increased awareness and simple changes are the first steps to reducing knee injuries.

May 1, 2008

By J. M. Singer

This study was undertaken to obtain some fundamental information about hazardous mixtures of coal dust and methane (firedamp) likely to occur in mines. Fuel concentration limits for ignition of mixtures of coal dust, methane, and air have been determined by a hot-gas ignition method. The limiting concentration of each of the two fuels was usually less than that corresponding to its lean flammability limit in air. The lean limits of flammability of coal dust vary with the type and size of the dust; in this study coal dust concentrations were less than 80 mg/liter. Ignition jets were turbulent pulses (emerging from a channel of 0.5 cm diam) resulting from explosions of stoichiometric mixtures of methane, oxygen, and nitrogen, Temperatures of the ignition jets were varied by changing the oxygen index (OI) = O2/(02 + Nj2) of the primary methane-oxygen-nitrogen mixture (adiabatic flame temperatures from 2,000° to 3,000° K). The objectives of the study were to establish quantitative relations between concentrations of each fuel at ignition limits of hybrid mixtures and to study the mechanism of ignition of these hybrid mixtures by hot turbulent gases, Empirical equations were fitted to concentrations for four coals, namely) Pittsburgh Seam (sizes A, B, and C), Sewell No.2 Seam, pocahontas No.3 Seam, and anthracite. Equivalences of coal dust to methane were computed from these equations; equivalence being defined as -Ac/Am, where c is the coal dust concentration and m is the methane concentration, each in milligrams per liter of air. It was found that the equivalence increases as the temperature of the hot-gas jet decreases. In general, the equivalence is also an inverse function of volatile content of the coal and a direct function of the particle size, However, volatile con-tent in itself is not a sufficient correlating variable, nor is the specific surface area of the coal dust.

Jan 1, 1967

The corrosion behaviour of a low carbon steel was investigated in natural seawater and various synthetic seawaters. It was found that the steel corroded nearly four times faster in a 3.5% NaCl solution than in natural seawater for an exposure time of 21 days. The corrosion rate after immersion in synthetic seawaters (ASTM D1141 and Marine Biological Laboratory seawater) is similar to the corrosion rate after immersion in natural seawater. Calcium carbonate (aragonite) deposits were found on the surface of the steel after immersion in natural seawater and the synthetic seawaters. Some magnesium-containing deposits were also found after immersion in the natural seawater. These deposits act as a barrier against oxygen diffusion and thereby lower the corrosion rate. The morphology of the calcium carbonate deposits that formed during immersion in the natural seawater is different from those formed during immersion in the synthetic seawaters. This may explain the slightly lower corrosion rates obtained in the natural seawater. X-ray diffraction also showed that the oxy-hydroxides formed in the 3.5% NaCl solution differed from those formed in the other solutions. Keywords: Corrosion, seawater, low carbon steel, 3.5% NaCl, aragonite

Jan 1, 2006

By Timothy P. Smirnoff

Sustaining the region?s mobility needs, achieving projected economic growth, and maintain Midtown Manhattan as a center of regional, national and global importance has led to continued investment in commuter rail and transit infrastructure in New York City and resulted in design and construction of large underground caverns. The current plans for stations in Manhattan include New York Penn Station Expansion (NYPSE) caverns for Trans Hudson Express (THE) Tunnel Project for New Jersey Transit (NJ Transit) and the Port Authority of New York and New Jersey (PANYNJ), Metropolitan Transportation Authority Capital Construction Long Island Railroad (MTACC/LIRR) twin caverns for East Side Access (ESA) Project, and station caverns of the No. 7 Line Subway Extension Project and Second Avenue Subway Project for Metropolitan Transportation Authority Capital Construction/New York City Transit (MTACC/NYCT). This paper provides a general overview of these large caverns now in design or construction in Manhattan, the area?s geologic setting, the geotechnical factors considered and approaches commonly applied for cavern design.

By David A. Orava, Richard C. Swider

"The technical knowledge and practical experience accumulated by industry and others in abating acid mine drainage (AMD) is being proactively applied at every phase of the mine life cycle. This paper traces the mine life cycle from exploration to post closure monitoring and maintenance, and reviews AMD abatement measures that have become an integral component of exploration and mining activities.Attention is increasingly being given to evaluating AMD potential as part of exploration work, and studies related to project feasibility and design. Mining, mineral processing, and waste management options are selected taking into consideration their suitability to inhibit AMD. These inhibition measures are typically committed to in closure plans submit-ted at the permitting stage. Mines are operated and decommissioned, often progressively, as planned and in accordance with environ-mental protection policies."

Jan 1, 1996

By Steve Kral

It seems that mining has been in the doldrums for awhile. Except for gold, metals prices remain depressed. And economic conditions in the United States and around the globe have put governments in a financial bind. This affects new building and infra-structure repairs, which, in turn, have a major impact the building materials industry. Add to that the severe environmental and regulatory restrictions placed on the mining industry in developing new mines and expanding existing ones. It’s enough to make a mining engineer/geologist/metallurgist go sell real estate. So why do those employed in the mining industry stay in the business and remain optimistic? Many of them will say that they have been through down cycles before and know that an upswing is in the offing. They also know that society will always need the commodities they produce. And they love the challenge. The challenge in mining’s case is producing commodities as cheaply as possible, in an environmentally sound manner and improving the quality of life in the communities where they work.

Jan 1, 2003

By Lei Zhang, Zhibo Ma, Pingye Guo

The mechanical behavior of hard roofs often leads to significant deformation and strong mine seismicity in gob-side entry retaining (GER) of the longwall mining, affecting the mining safety and efficiency of coal mines. Field investigations indicate that the failure process of the retained entry by hard roofs can be divided into three stages. In this paper, theoretical analysis and numerical simulations are first used to evaluate the damage process of the retained entry under the hard roof. The results show that the instability of the retained entry in the conventional GER method results from the combined static-dynamic loads (in stage II and stage III) from the hard roof. Then, an innovative method, through fracturing roofs to maintain entry (FRME), based on GER with the hard roof is introduced to solve this problem. In this method, the roof of the mining area is pre-fractured, and when the coal seam is mined, the direct hard roof will collapse along the fractured surface due to its deadweight and mining pressure. The hard roof control effect on the static and dynamic loads, taking into account the innovative method, is verified with simulations and theoretical analyses. The results are compared with those of the conventional GER method. Furthermore, based on the numerical simulation study of dynamic responses, it is found that compared to the GER method, the dynamic response of the retained entry using the innovative method is more moderate and more conducive to the stability of the entry. Field application also validated the effectiveness of the innovative method to control the mechanical behavior of the “massive sudden collapse” of the hard roof.

Aug 14, 2023

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By Robert W. Van Dolah

On December 27, 1961, a fire and explosion destroyed the blasting agent mixing plant and an attached storage barn of the Whitaker-Atlas Supply Co., near Norton, Wise County, Va. Five residences, an office building, four trucks, and three automobiles were completely destroyed; a house trailer and several other trucks and automobiles were severely damaged; and other property damage, including much window breakage, occurred up to 3 miles or more airline distance away. Through the quick action of the fire marshal of the Norton Fire Department, Norton, Va., there were no fatalities and only five persons required hospitalization. This incident is of particular interest because of the widespread practice of mixing fuel oil (FO) with ammonium nitrate (AN) to prepare low-cost blasting agents, in many cases under conditions and circumstances not very different from those presented here. A representative of the Bureau of Mines Explosives Research Laboratory, Pittsburgh, Pa., and field representatives of the Bureau's Health and Safety Activities conducted the investigation. Information in this report was obtained from representatives of the Whitaker-Atlas Supply Co., the Norton fire marshal, and others who were on the scene either shortly before or after the incident occurred. Representatives of the Manufacturing Chemists' Association, the Institute of Makers of Explosives, and individual ammonium nitrate producers participated in the inquiries and investigations.

Jan 1, 1962

By A Hatt

This paper presents a case study of characterisation work undertaken at a greenfield exploration project to provide engineering and OH&S inputs for the design of a ventilation system. The paper discusses how comprehensive early characterisation of the ambient surface and underground environment including aspects related to heat, dusts, strata gas, and geologic/mineralogical factors enables incorporation of the right ventilation and non-ventilation controls at a study level to mitigate the risks identified.

Oct 12, 2022

By J M. Parr, P M. Herzig, J B. Gemmell, S D. Scott

PACMANUS is an actively-forming seafloor analogue of volcanic-hosted massive sulfide orebodies, situated on the crest of an andesite-dacite-rhyodacite ridge overlying rifted older arc crust in a back-arc basin. Hydrothermal deposits range from Mn-oxide crusts to Cu-Zn-rich massive sulfide mounds and chimneys containing significant Au and Ag. Preliminary data suggest a substantial magmatic component to fluids and metal sources, and we speculate that PACMANUS is the cap to a complete hydrothermal system including subvolcanic and intrusive-related mineralisation.

Jan 1, 1995

The nature of the specialty glass and ceramic business magnifies the dependency of the ultimate product on the unique properties of their raw materials used to make them. This dependency has implications in the management of risk in the supply process which requires a special procurement organization and program commitment to be successful. The Coming system of managing critical materials and factors in development of alternate new suppliers and products is discussed.

Jan 1, 1989

By W. Hurst

The authors of this paper, in substituting values in a material balance equation associated with a gas reserve and a water drive, cannot find sustainment of what the gas in place should be; therefore, their conclusion is that this type of problem dealing with gas reservoirs is insoluble. They have introduced the word, "cybernetics," based on the work of Norbert Wiener, that further extends this line of reasoning, namely, to the effect that the system is a "black box", and that the gas reservoir and aquifer can take on infinite aspects 'based upon their past performance, to quote the authors. The inference is that this black box is an unknown. which permits in computer programming to subscribe as many variables as possible to observe by adjustment of one to another those combinations of conditions that fit field behavior. This may satisfy those in this discipline whose dedication is to programming, but to the others this is a comparison to the rationalization of the combinational results of the throwing of dice—a probability procedure. In reservoir engineering we are more direct. We learn from the examination of individual we'll and field data exactly what is in this black box. I now come to the impasse that has confronted these authors in their machine calculations. In this I have reproduced from their own production data (Tables 1 and 2 of their paper) pressure vs cumulative gas produced. shown as Figs. D-1 through D-5. A perusal of any of these five plots, for the corresponding fields in the Po Valley, shows the straight-line relation of pressure vs gas produced, evidencing pressure depletion. The point I make is that in their fundamental production data, there is no variance from a straight line that can support a water drive.

By S Graskoski

The allocation of boggers and trucks at Telfer’s sublevel cave mine is currently assigned by manual techniques, with decision-making primarily dependant on the judgement of the operators and mine control. Field observations indicate that allocation decisions could be improved by establishing a systematic approach to dispatch. An investigation into the current state of technology determined that no currently available solution would provide a tool to make optimal decisions for the Telfer dispatch challenge.In an underground sublevel cave (SLC) environment, the destination decision is fixed and the source is variable, so open pit and block cave solutions are not relevant. Newcrest underwent a development venture with an external vendor to develop a novel production dispatch algorithm and user-friendly software program to make allocation decisions in a systematic way with consideration given for the true complexity of the operation.This new production software, nicknamed Dingo (for Dispatch ‘n’ Go), is a smart way to assist forepersons and mine control operators in their day-to-day roles of planning shifts and allocating trucks and loaders to optimal locations during shifts.CITATION:S Graskoski, 2017. Dingo – an optimisation tool to solve complex short interval control at Telfer underground mine, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 261–266 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R. J. Craig

Introduction All mining operations produce rock dust. Inhalation of rock dust, particularly if it has a high silica content, causes silicosis. Silicosis is, therefore, recognized as a hazard of the mining industry and has been made compensable throughout most of Canada. Most of the dust in any mining operation is caused by rock drilling and blasting operations and the movement and transportation of broken rock. Dust from blasting cannot be eliminated, but it can be controlled by means of increased ventilation, the use of water sprays, and the control of blasting hours. Dust from ore movement can be reduced by keeping the broken rock in a moist condition at all times. The dust from the rock drilling operation has been found to be the most difficult to control. Concentrations of dust caused by rock drills in stopes can usually be reduced to the safe minimum of 300 particles per cubic centimeter (p.p.c.c.) by diluting the air with increased ventilation. In development headings, where the machines are more confined, this is not always practicable. Therefore, the dust must be eliminated at its source. This paper deals with the reduction of dust from Leyner machines by adopting improved designs.

Jan 1, 1947

By Todd M. Ruff

An average of 13 mine workers are killed each year by being run over or pinned by mobile mining equipment. At surface mines, these accidents commonly involve large dump trucks that drive over a smaller vehicle or a person that is in the dump truck’s blind spot. One method of detecting a person or another vehicle in a blind spot is to use some type of sensor technology such as radar or radio-frequency identification (RFID). Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health tested a number of commercially available and experimental sensors that monitor obstacles in a vehicle’s blind spots. None of the sensors had been previously applied to the specific problem of rigid-frame surface mining trucks. This report documents the procedures and results of tests conducted after RFID and radar systems were mounted on a 50-ton-capacity dump truck. It was determined that both RFID and radar technology show promise for detecting obstacles in the blind spots of mining equipment; however, more development work is needed to meet the unique requirements of mining equipment and the mine environment.

Jan 1, 2000

By Renfeng Song, Shaoyan Wang, Zhiqiang Zhang, Ke Guo

Leaching titaniferous magnetite concentrate with alkali solution of high concentration under high temperature and high pressure was utilized to improve the grade of iron in iron concentrate and the grade of TiO2 in titanium tailings. The titaniferous magnetite concentrate in use contained 12.67% TiO2 and 54.01% Fe. The thermodynamics of the possible reactions and the kinetics of leaching process were analyzed. It was found that decomposing FeTiO3 with NaOH aqueous solution could be carried out spontaneously and the reaction rate was mainly controlled by internal diffusion. The effects of water usage, alkali concentration, reaction time, and temperature on the leaching procedure were inspected, and the products were characterized by X-ray diffraction, scanning electron microscope, and energy dispersive spectroscopy, respectively. After NaOH leaching and magnetic separation, the concentrate, with Fe purity of 65.98% and Fe recovery of 82.46%, and the tailings, with TiO2 purity of 32.09% and TiO2 recovery of 80.79%, were obtained, respectively.

Jun 16, 2021

By F. W. Wood

The Bureau of Mines has sought clarification of the Ti-TiN system by studying the phases formed by diffusion reactions between titanium and titanium nitride. Reaction couples were prepared by embedding pockets of TiN powder in arc-melted buttons of titanium. Specimens were vacuum annealed at nominal temperatures of 800°, 950°, 1,200°, and 1,500° C. Metallographically mounted cross sections from reacted specimens and from some that were not annealed were examined optically, with an electron microprobe, with an election microscope, and by X-ray diffraction. Each annealed specimen contained a segregated core primarily of d-phase material, an ?-phase diffusion layer, an a-phase diffusion layer, and host metal. On the basis of corresponding microprobe analyses, and considering results of certain other research, a new phase diagram is proposed. It contains no qualitative innovations, only quantitative adjustments. Results were also analyzed from the viewpoint of diffusion behavior. Diffusion coefficients calculated for the ? phase were sufficiently scattered that the parameters are very tentative. Nevertheless, the diffusion behavior reported is in reasonable agreement with one of two prior studies if it is assumed that the earlier investigators were mistaken in their identification of the nitride phase in which the diffusion occurred.

Jan 1, 1974