Search Documents

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By Masaki Kitazume

"Abstract The wet type and dry type of deep mixing methods have been developed and widely applied for on-land and marine constructions in Japan. The quality assurance (QA) of the methods has been usually carried out by unconfined compression test on field stabilized soil sampled by core boring in Japan. In some other countries, stabilized soil excavated by the wet grab sampling instead of core sampling is often subjected to unconfined compression test for quality assurance. There are several merits and demerits in each method, but few studies have been carried out to compare the stabilized soil strength of these two types of specimens to discuss their applicability to practical construction. The author has conducted a series of field and laboratory tests to compare the stabilized soil strength and discuss the applicability of wet grab sampling to QA for wet and dry types of deep mixing method.In this study, the wet grab sampling was carried out at two road embankment construction sites where the wet type and dry type of deep mixing were applied. The cement stabilized soil was excavated at the three depths by a wet grab sampler soon after the DM column construction. The test result is compared with the other test data in the previous study to discuss the applicability of the web grab sampling method for QA of cement stabilized soil.IntroductionThe Deep Mixing Method (DMM), an in-situ soil stabilization technique using cement and/or lime as a binder, is often employed to improve soft soils (Kitazume and Terashi, 2013). A variety of factors and their interactions affect the eventual strength of a deep-mixed column, while some of which are controllable (e.g. binder type and dose) by engineers while the others are not (e.g. soil types, ground temperature, etc.; Babasaki et al., 1997). In addition to laboratory mix tests, which in essence are a parametric study to estimate the influence of these factors on a particular soil’s strength, the quality assurance (QA) practice in Japan usually involves unconfined compression test on sampling cores from the stabilized columns after a given curing period. It has been recognized, however, that the ‘field strength’, or the strength of the retrieved core, quf is on average lower than the ‘laboratory strength’, qul, evaluated by laboratory mix test. Also allowing for the inevitable variability, existing guidelines (for example, PWRC, 2004 and CDIT, 2008) recommend the design quf /qul values of, for example, 0.5-1.0 for the CDM (Cement Deep Mixing; a wet-type technique, in which binder is added as slurry) and 0.2-0.33 for the DJM (Dry Jet Mixing; a dry-type technique, in which binder is added as powder)."

Jan 1, 2014

By D Matthews

With the increasing demand for quality-specific ores, coupled to the reality of even more complex minable iron ore reserves, there is a growing need for real-time online material analysis of plant feed and product. For a full system mass balance, the combination of conveyor weight scales, flow and density transmitters are required. This alone does not guarantee product grade. For optimal process control and material blending, real-time online elemental scans in combination with the mass weighting is becoming more than a ‘nice to have’. These elemental scans located at key positions, enable the mining and plant operators to make informed decisions timeously, therefore ensuring product outcomes and optimising operations where material grade and the control thereof are important. Typically, these units follow the mining and primary crushing circuit as well as on the product conveyors, low-grade conveyors and tailings lines. Deployed after the primary crushing circuit, an analyser acts twofold:1. guaranteeing mining production, and2. processing facility feed blends.The analysers on the product conveyors guarantee saleable product. The analysers on the low-grade conveyor and tailings line complete the elemental balance and identify the potential of the low-grade and tailings for future processing. The system losses (accumulation) are calculated to determine the amount of material ‘lost’ during the processing stage which does not report to any of the aforementioned and can be used as a measure of the efficiency of the plant. A further advantage of the real-time online analysis of material is that immediate intervention can be taken in the event that the product is not of saleable product grade requirements. In the Khumani Iron Ore mine, Northern Cape, South Africa, run-of-mine (ROM), product and control analysers were included. Run-of-mine and product stockpiles are certifi ed, low-grade material is not currently directly measured, but calculated from the internal control loops. Iron units are reconciled between product and feed material.

Jul 11, 2011

By W. P. Campbell

Introduction OWING to the necessity of curtailing the length of this paper, nothing like an exhaustive treatment of the subject will be attempted. Instead, merely a few aspects will be considered, viz., water trouble in wells, sampling of waters, analysis, methods of reporting analysis, and the comparison of a few typical waters. The waters discussed will not be confined to those occurring in areas where oil or gas has already been found, but will include samples from areas in which drilling is being carried on in the hope that oil or gas may be found, i.e., from unproved fields. The Water Problem The problem of dealing with water encountered in oil and gas producing areas has engaged the attention of petroleum engineers from the early days of the industry. Water was not always considered a menace to oil sands; indeed, a certain amount of it was considered beneficial in some areas, but if such exist today they are very exceptional. In some fields, the problem is more acute than in others, and at times has baffled all attempts to solve it satisfactorily. Wells have been brought-in with promise of good production, but after a brief period have 'gone to water'. Whether ?it has always been a case of poor engineering in the form of unsuccessful water shut-off of 'top' or 'bottom' water, or because 'edge' water was present and water and oil were in such close contact it was impossible to remove the one without the other, is hard to say.

Jan 1, 1929

By Gabriel Esterhuizen

The room-and-pillar mining method is used extensively in underground limestone mines in the Eastern and Midwestern U.S. The rock mass is typically a near-horizontal, bedded deposit at relatively shallow depth. A survey of 34 mines was conducted in which data on roof spans, rock mass properties and support practices were collected as part of a National Institute for Occupational Safety and Health research project into ground control in limestone mines. The average room width is 13.5 m (44 ft), accommodating large mechanized equipment. The results show that the immediate roof beam can consist of many individual layers and can contain several near-vertical joints. In spite of the room widths, the roof is naturally stable in many mines. Observed roof instabilities can generally be related to excessive horizontal stresses or unfavorable geological structures that cause block fallout or beam failure of the bedded roof rocks. The survey showed that the rock mass quality of the limestone does not vary significantly throughout the Eastern and Midwestern U.S. Roof conditions and the need for support were found to be closely related to the thickness and competence of the first layer of limestone in the roof. The findings highlight the need to identify local geological structures and the roof beam characteristics so that support alternatives can be evaluated. Monitoring and observational technologies that are available for identifying potentially unstable roof are presented, which include: roof characterization using the Rock Fall Risk Index, automated logging of roofbolt hole drilling, microseismic monitoring and displacement monitoring.

Jan 1, 2007

By Kenneth P. Neumann

The development of the Cyprus Thompson Creek Molybdenum Deposit near Challis, Idaho, began in 1967 when the first mining claims were staked on the intrusive rock outcrop. Exploration drilling continued for the next 14 years. During 1978, a decision was made to develop the deposit. In December, 1980, approval of the Environmental Impact Statement was received and construction of facilities and waste rock removal began. By the middle of 1983, 126 M metric tons of rock had been removed and all facilities were completed. The high work ethic of Cyprus Thompson Creek employees combined with innovation has made the mine one of the most efficient in the United States today.

Jan 1, 1983

By R L. Brathwaite

As part of an investigation of the deep structure of the Waihi Basin, an extensive set of resistivity measurements was recently collected by DSIR Geology & Geophysics. The objective of this work is to map deep resistivity changes throughout the Waihi area in order to contribute to a better understanding of the regional geophysical structure. This research is also aimed at improving techniques for locating 'deposits of epithermal mineral resources, and helping to establish their origin and genetic relationship to fossil geothermal systems.   The results indicate that the basin south of Waihi is underlain by an extensive layer of low resistivity, modelled as a 5ohm-m layer several hundred metres thick. Lake sediments (mudstones), as exposed in the south western part of the basin, near Waitawheta, are the most likely source of this low resistivity layer, although hydrothermally altered clays and/or elevated temperatures are other possible causes. Strong northeast trending anisotropy is also observed, implying structural links from Waitawheta through to Golden Valley. The observed resistivity pattern is consistent with a æburied calderaÆ or æfaulted depressionÆ structural model for the basin, as inferred from gravity and magnetic data.

Jan 1, 1991

By Thomas Fiest, Helmut Wannenmacher, Wulf Schubert, Manuel Entfellner

Mining and tunneling in so-called “squeezing ground conditions” at high in-situ stress can result in substantial and enduring ground deformations. The magnitude of deformations is closely tied to the applied excavation- and support concept, though typically, they can reach tens of centimeters. The yielding principle is based on the idea, that the need for support capacity decreases as deformation increases. To enable controlled ground deformation and safe working conditions, yielding elements as a part of the shotcrete lining are implemented. These types of elements avoid an overstressing of the shotcrete lining. During the deformation process, the support pressure of the yielding elements and lining increases, thus stabilizing the ground. Furthermore, long-term creep deformations of the rock mass can be absorbed with such a system. This economic support technique represents the state-of-the-art infrastructure tunneling practice in squeezing ground condition. A novel yielding element of High-Strength Expanded Polystyrene (HS-EPS) was invented, which overcomes existing systems’ drawbacks. This innovative system is lightweight and allows for safe and rapid installation. Furthermore, the modular setup of the element enables an easy on-site adaption to react to in-situ deformation patterns and changing ground conditions. Recent experiences from applications in Alpine base tunnels in squeezing ground are presented.

Jun 25, 2024

By P. H. Davenport

"The ore-element patterns in regional lake sediment geochemical survey data from four areas of Newfoundland containing granite-related mineralization reveal characteristics which can be used to identify mineralized granitoids. The St. Lawrence Granite with its fluorite deposits, the Ackley Granite with molybdenite mineralization, the Grey River tungsten lodes and the newly discovered Mo- W mineralization at Granite Lake, Central Newfoundland, have all been included in the regional lake sediment geochemical surveys, which now cover about 90,000 km2 of the Island of Newfoundland. The lake sediments over these mineralized granites show diagnostically high values of Mo, F, Pb, Zn and, in three of the four cases, U, together with locally high Ag and Cu values. Furthermore, these ore-metals display a distinctive zoning pattern about the intrusives, which can be related to the classical ore-metal zoning patterns developed about many types of mineralized granitoids.IntroductionGranitoids in Eastern Canada are receiving renewed interest as potential hosts of tin, tungsten, uranium and related mineralization. Although a number of mineral deposits and showings have been known from a few granites (sensu lato) in the region for many years, granites had generally received little attention as potential hosts of metallic mineralization until the recent resurgence in interest in the mineral potential of these rocks. In Newfoundland, where granitoid rocks underlie about 30070 of the land area, petrologic data are available from some granites, particularly those in eastern Newfoundland (Strong et al., 1974; Strong, 1980), but in southern and southwestern Newfoundland the data base is sparse, and indeed in many cases individual plutons are not delineated on the geological maps of the area . Most of the available data on Newfoundland graniotolds have been summarized by Strong (1980), who gives a general assessment of their mineral potential by comparing their physical, mineralogical and petrochemical attributes with mineralized granites elsewhere in the world."

Jan 1, 1982

By H. Soto

As a follow-up to a laboratory study, a pilot scale column for the flotation of coarse particles was designed and then tested in two different applications. In the first test, the concentration of a coarse phosphate ore (normally beneficiated by skin flotation in spirals) was carried out in a flotation plant in Florida. In the second pilot test, the column was used as a scavenger cell in the coarse flotation section of a potash beneficiation plant in Saskatchewan, Canada. Particle size of the phosphate feed was of the order of 0.6-1.0 mm and the potash feed 1-3 mm. The column was 1 feet diameter and was fed at rates between 0.5 to 1.4 tph. The effect of operating variables such as air and water flow rates, bubble size, frother concentration, residence time, sparger, etc were evaluated. The most important factors in column performance were found to be bubble size, air flow rate and the thickness of the froth bed. Best results were obtained in the absence of a froth bed, with low air flow rates and with small bubbles. The paper presents comparative performance and discusses details of the column design. Phosphate recoveries in the column were better than 90% whereas the conventional skin flotation circuit normally yields about 60% recovery for a comparable concentrate grade. Potash recovery from the tailings of the conventional flotation circuit was as high as 42% recovery. Particle size distribution of the potash concentrate was coarse enough to meet requirements for potash fertilizer.

Jan 1, 1993

By F T. Suorineni, L Baird, A Papaioanou, D Hines

The Mathews et al (1981) stability graph was developed to provide guidance in the determination of stope sizes to control dilution in bulk mining of large orebodies. Longhole and sublevel open stoping (LHOS and SLOS) are the lower end in scale of underground mass mining with panel and block caving (PBC) at the higher end. Currently, the stability states of stopes in the stability graph are described qualitatively as stable, unstable or cave. The alternative quantitative option to the qualitative stability graph is the Equivalent Linear Overbreak Slough (ELOS) stability graph. The ELOS stability graph only applies to narrow vein orebodies. It is easy for the Mathews et al (1981) and the ELOS stability graphs to be applied outside the limits of their databases. What is currently referred to as ‘stable’ in the present stability graphs has diverse interpretations at different mines depending on their acceptable dilution values. In 2014, a research program was conceptually conceived at the UNSW Australia School of Mining Engineering to develop a quantitative dilution-based stability graph independent of orebody width to address some industry concerns on the use of the stability graphs. A dilution-based stability graph provides the mining engineer the flexibility to determine open stope sizes based on what dilution amounts are acceptable. The graph also unifies both the Mathews et al (1981) and ELOS stability graphs for wide and narrow vein orebodies, thus, eliminating their potential misapplications. To date, the concept is proven with case studies from metalliferous underground mining operations located across Australia. This paper presents the dilution-based stability graph concept, the initial results and future plans to account for other critical factors and increase confidence in its application with the addition of more data outside Australia.CITATION:Suorineni, F T, Papaioanou, A, Baird, L and Hines, D, 2016. A dilution-based stability graph for open stope design, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 511–522 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Tumbling mills and some theoretical and practical aspects of milling are discussed. Attention is directed towards the difficulty of relating the dynamical analyses of the motions of particles within mills to the existing treatments of breakage processes. This synthesis may be advanced by a study of milling that utilizes the matrix analysis of breakage processes. Application of the matrix analysis to results obtained on (i) grinding in open-circuit a zinc ore in a conical pebble mill and in a modified conical mill, (ii) "grinding of cement clinker in a compound mill, and (iii) to some drop-weight grindability tests is discussed. It is shown that the 'IT-breakage model adequately describes the breakage processes of each of the tests. (The proportion broken in each breakage cycle is given by 'IT and is independent of particle size.)The size distributions of the products are accurately predicted in the cases considered. Matrix analyses of the breakage of coals, various ores and a cement clinker have been made. Appendices give an elementary account of the matrix methods and give the equations fully describing reverse order closed circuit operations. The matrix analyses of breakage processes and the survey are used to examine briefly closed circuit grinding.INTRODUCTIONTumbling mills are slow-speed crushing and grinding machines which have been developed from some fairly simple types into many widely differing forms. Many of these versatile mills have proved extremely useful in ore dressing and mineral beneficiation, whereas others have been used in the cement industry and less extensively in the coal industry.The performance of even the simplest tumbling mill is very imperfectly understood, whilst the more difficult problems associated with the balancing of complex milling circuits and with the establishment of the optimum operating conditions for the whole of a complex circuit are even less well apprehended.Our knowledge of the performance of tumbling mills is rather sharply divided into two categories: the first consists...

Jan 1, 1957

A201 aluminium alloy is a high strength casting alloy with a nominal composition of Al-4.6Cu-0.3Mg-0.6Ag. It is strengthened by the O(Al2Cu) phase and the ??(Al2Cu) phase during heat treatment. Further strengthening of this alloy system can be obtained through the addition of transition elements, but care must be taken as other elements might have adverse effects on the mechanical properties. The objective of this study is to determine the influence of Mn on the tensile properties of rheo-processed Al-Cu-Mg-Ag alloy A201. ThermoCalc software was used to predict the different phases that can be expected in the alloys, and scanning electron microscopy(SEM) with energy dispersive spectroscopy (EDS) was used to investigate the actual phases that formed. The influence of these phases on tensile properties is quantified. SEM and ThermoCalc revealed that there is an increased amount of the Al20Cu2Mn3 with increasing Mn. The tensile properties showed that high amounts of Mn do have adverse effects on the tensile properties of alloy A201, especially the ductility. Keywords Semi-solid metal (SSM) forming, alloy A201, intermetallics, Al20Cu2Mn3

Jan 1, 2011

By Jochen Belz, Allan Henneker, Nod Clarke-Hackston

For the construction of tunnels and other underground structures, extraction of the exact amount of material is of paramount importance both economically and for engineering purposes. In the Sequential Support Method (NATM) immediate (sequential)and smooth support by means of shotcrete, steel arches, lattice girders and rockbolts, either singly or in combination are used; cutting of the precise (albeit sometimes of complex geometry) profile is an integral part of the method. In order to save unnecessary excavation and provide better information to the machine operator, VMT GmbH has developed a system to support precise excavation of the tunnel profile when using road headers or other partial face cutting machines. This paper outlines the principles of this system with examples from Australia, Ger-many, Sweden and Spain and will cite examples of typical savings achieved.

Jan 1, 2007

By Brajendra Mishra

Molten Salt electrolytic processes offer unique opportunities to extract and refine metals where gaseous or metallothermic reduction, hydro metallurgical extraction and aqueous electrolytic methods are thermodynamically constrained. Production of aluminum and magnesium by molten salt electrolysis are well known commercial processes. Several other reactive metals, such as lanthanides and actinides, as well as beryllium and calcium, make use of molten salt processing for extraction and refining. This presentation describes the science of molten salt chemistry and electrochemistry for winning and refining of several metals. In addition, recovery of metals from waste process salts by molten salt reduction as well as oxidation have been discussed. Material issues in design of molten salt reactors have been included. Various applications have been presented through case studies. Experimental data have been included to justify the suitability as well as limitations of these specific processes.

Jan 1, 2003

By John Brennan

Necessity, they say, is the mother of invention. Certainly that sentiment held true during the early stages of explosive engineering. While seaside forts were concerned over static ignition of their black powder caches in the 14th century1, the mining industry in the 1800s were plagued by accidents surrounding the ignition methods for their black powder blasts.

Jan 1, 2011

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By Geir Martin Haarberg

Modern electrolysis technologies can provide possibilities for developing sustainable processes in terms of energy and environment. Laboratory experiments were carried out to study electrodeposition of iron from molten salts and aqueous solutions using an inert oxygen evolving anode to eliminate the emissions of CO2. The possibilities of molten salt electrorefining of metallurgical grade silicon to produce solar grade silicon were also investigated. Electrochemical techniques were used to study the electrochemical behaviour of dissolved iron, silicon, and titanium species. Bulk electrolysis was carried out to deposit pure iron, silicon, and titanium. The quality of the deposits was studied by SEM/EDS and XRD analyses. Calculations based on laboratory studies indicate that great improvements in terms of reduced energy consum

Jan 1, 2010

By M. A. Kujoana

Following on the design of good mining layouts and regional support systems, and the implementation of sound strata control practices, stope support is the ultimate strategy to combat the hazards of rockfalls and rockbursts. The primary function of stope support in intermediate and deep level mines is to stabilize the rock mass immediately surrounding stoping excavations, that is, the zone of fractured rock which behaves in elastically around stopes. Support design is a process resulting in a support system which is both practical and meets or exceeds by a factor of safety the requirements for a particular geotechnical environment. The aim of this project was to design a support system, which accommodates the factors of rockfalls and rockbursts. The pack support unit must be easily handled, less costly and can be used in stopes without any significant convergence. The project tested the structural stability of packs to their expected deformation, in order to design a height to width ratio for stopes where little convergence is expected.

Jan 1, 2009

By L. B. Slichter

Prospecting is certainly the world's biggest and best gambling business. It is a game where the chips cost many thousands and where many millions, even billions, can be won. An attractive feature of this gamble is the fact that the players are free to rig the odds as favorably as possible. Only the limited bounty of nature, the restrictions of the laws of the land, the competition from other players, the limited sagacity of the player himself— only these, and other factors, restrict the possibilities for large winnings. Today probably about half the land surface of the earth remains to be searched for signs of ore visible at the surface. It is fortunate that so much land still remains for exploration by relatively economical methods. Looking to the future, it is a good guess that the costs of finding ore will increase in response to increasing technical difficulties. To continue to achieve profits from prospecting, it will become necessary to analyze the business more skillfully, in a more and more sophisticated manner. Whenever feasible, qualitative concepts must be replaced by their quantitative equivalents, improvements, and extensions. THE GAMBLE The fact that prospecting is a gambling business reminds us at once of the elementary rule known as the law of gambler's ruin. I hesitate to mention so simple a rule in this company of experts. This rule expresses the rather serious chance of going broke when the odds for success are small, merely by a normal run of bad luck regardless of the long-run expectations of gain. The only sure way of avoiding this special risk of gambler's ruin is to have enough capital, and the will, to continue the play many times and thus ride out the inevitable runs of bad luck. For example, if the probability of success is one in ten for each venture, there is a 35 pct chance that ten successive ventures will fail in a row. But if one has the capital to continue the play through a run of 100 failures, then the chance of gambler's ruin is only 5 in 100,000. Almost any management, I suppose, would be under terrific pressure to cease the play during a long run of bad luck. To continue to prospect under such circumstances requires great confidence in the premises, and a firm conviction in the long-term expectation of profit. There is evidence which I shall mention that in the future even the strongest companies may not have the necessary capital to prospect on the ideal scale. Joint ventures will be very desirable as a means for extending the available venture

Jan 1, 1961