Search Documents

By Tim Peterson

Factors Controlling Stability Stability of slopes in soft rock, waste dumps or soils is governed by three factors: ?Slope configuration ?Groundwater ?Shear strength

Jan 1, 2004

By G. McIsaac

This paper discusses the formulation of a linear program with the objective of maximizing the cash flow of the long-term plan of an underground operation. A mine is split into eleven independent ore zones, each characterized by its reserves, required development, and mining method. Based on practical considerations, maximum rates are set for each zone?s development and production capacity. For the total mine plan, a minimum daily production rate is set along with a minimum feed grade to the mill. A maximum daily development capacity is set based on the equipment and labour available. Proven and probable ore is mined preferentially over possible ore in the early years of the plan. Also, the fixed cost of operating the mine is taken into consideration whenever mining activities take place. Once the linear program is solved, it can be critically reviewed, and unrealistic results can be identified. Some resource allocations constraints can then be changed in certain sectors, and new results can be analyzed. ?Whatif? scenarios can also be examined, such as determining the impact of hiring a contractor to develop a given sector, or dropping an ore zone completely from the plan.

Sep 1, 2005

By Andrew R. Klaetsch, Peter W. Deming

"The Washington Avenue tunnel in Kingston, NY was completed in 1912 to convey combined storm water and sanitary sewage. Over a mile in length, the tunnel was driven almost entirely in bedrock, with the exception of an approximately 170 foot long brick arch segment constructed in soil. About 90 years after the tunnel was put into service, persistent subsidence problems and sinkholes were observed in Washington Avenue above the shield-driven soil tunnel segment, eventually causing the important traffic thoroughfare to be closed. Subsequent tunnel inspections revealed a breach in the brick arch and a significant volume of fine soil within the tunnel. A two-phase remediation program was implemented to control seepage, reduce soil migration, and remedy sinkhole problems. The first phase included in-situ soil densification by vibratory pile probe driving to improve density in shallow sandy soil loosened by ground loss. The second phase included installation of a continuous soilcrete arch structure over and alongside the tunnel, extending to rock or compact glacial till and spanning the length of the soil tunnel segment. Overlapping vertical soilcrete columns were installed through interlayered sandy and clayey silt by jet grouting to form a continuous arch structure, using grout parameters verified by full scale field testing.PROJECT BACKGROUNDThe Washington Avenue tunnel in Kingston, NY (Figure 1) was completed in 1912 to convey combined storm water and sanitary sewage to Rondout Creek by the Board of Water Supply of the City of New York. The tunnel is over a mile in length and constructed primarily in rock. Contract documents indicate the tunnel was designed with a horseshoe shape at least 3 ft wide and 5.5 ft high."

Jan 1, 2016

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By John W. Colburn

A tractor-integrated version of an explosive ripping system was developed for mining application. This system utilizes diesel fuel and a tractor-mounted blower supplying 30 psig compressed air to a two-stage combustion chamber to produce a high pressure (600 psia) gas charge. The charge is rapidly released into the rock formation near the tip of the ripper. The system, mounted on a D9 tractor, was tested at several quarry and mining operations to investigate rock fracturing effectiveness. Although the results of comparative ripping passes conclusively demonstrated that the system increases rock fracture, performance of the system is strongly dependent on rock morphology and properties as well as basic performance of the tractor-ripper. The theory of conventional and explosive ripping modes is described and existing correlations of seismic velocity and ripper performance are shown to be in error.

Jan 1, 1977

By V. E. Dementiev, V. I. Kulikov, G. I. Voiloshnikov, Yu. O. Fedorov

"The report presents the summary of the JSC Irgiredmet’s activities in the field of preconcentration of ores. As of 2018, the Institute has almost 40-years’ experience in this area. Over the years, Irgiredmet has done a lot of work – from development to implementation of new technologies of ore piece sorting and concentration based on X-ray radiometric separation (XRRS). INTRODUCTION Preconcentration has been a challenging issue of the mining industry over the last decades. The implementation of this technology can significantly increase mining efficiency. The main application of preconcentration is improvement of mined ores quality, however new and more complex issues have arisen with the evolution of the technology. Irgiredmet has started to develop an efficient preconcentration technology for gold-bearing and rare-metal ores 40 years ago. The X-ray radiometric method widely used at that date as a method of elements determination in geology and geophysics become the ground for this work (1). Since that time, the Irgiredmet Institute has developed and significantly improved the technology of piece ore sorting, or XRRS (2-5), that is currently also known as the X-ray fluorescence method. The progress of the XRRS development achieved by Irgiredmet in cooperation with Rados LLC, Tekhnoros LLC (Krasnoyarsk), Rados-Service LLC and CJSC Tekhnogen (Ekaterinburg) has proved efficiency and applicability of the XRRS technology for processing a wide range of minerals and solving of various technological problems (7-9) compared to other radiometric methods (6). Furthermore, obtained results are supported by numerous studies, trials and implementations. The significance of ore preconcentration for greenfield and brownfield projects determined the establishing a new subdivision of Irgiredmet, the XRRS Technology Center (XRRS TC), that has provided the Institute with a completed range of processing technologies, from preconcentration to producing final products. Over the past few years, the XRRS Technology Center has carried out studies and testing of a numerous (more than 100) projects, mines and deposits of gold-bearing ores, rare metal ores (Be, Ta, Nb, W, Mo), base metal ores (Cu, Sb, Zn, Pb), ferrous metal ores (Fe, Ti, Cr), rough diamonds and coal. The XRRS Technology Center performs various specific studies and testing not only in Russia, but as well as in Kazakhstan, Georgia and Mongolia. Mines and companies from Chile, India, China, Iran and other countries also take an active interest in the XRRS technology."

Jan 1, 2018

By Jean-Pierre Hamelin

Ground movements induced by underground excavation are always of critical concern, particularly in urban areas. Compensation grouting now appears as a safe means to control these movements. The paper presents new advanced systems developed by the specialist contractor to bring, at all stages of the project, an efficient control of operations and presents a case history taken from the project at Tren Urbano, Rio Piedras Section, constructed beneath an historic commercial section of San Juan de Puerto Rico.

Jan 1, 2000

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By Xu Youzai

Static loading teets of five nodular piles and four non-nodular piles were performed in Tianjin soft clayey soil in which measurements of axial force and movements were made. Distribution of shaft resistance and load-movment curves for pile head and pile toe are presented in this paper. The applicability of nodular piles to soft soil and their effectiveness are also discussed. Based on the comparison, it is concluded that nodular piles have an advantage over non-nodular piles mainly in contri­bution to shaft resistance. Dynamic testing was also conducted through R. P. T. for evaluating the service load of tested piles.

Jan 1, 1991

By Thomas Schwind, Pamela S. Moran

For short tunnels, a reinforced cast-in-place lining is not economical and shotcreteis a logical substitution. In the past, reinforced shotcrete linings have been constructed with lattice girders and welded wire fabric. For the Russia Wharf Tunnel in Boston, MA, the Contractor, with the help of the Dr. G. Sauer Corporation offered the MBTA a VECP to substitute the reinforced cast-in-place concrete lining with a steel fiber reinforced shotcrete lining. The challenge was to adequately model the ductility of the steel fiber reinforced shotcrete and to test the shotcrete prior to and during construction to assure quality control. To our knowledge, this type of numerical simulation has not been used on any other tunnels in the US.

Jan 1, 2005

By P. Wittke-Gatterman

ABSTRACT: A three dimensional constitutive law for swelling rock is presented. It can be applied to the osmotic swelling of mudstone as well as to the swelling of rocks containing anhydrite. It describes the development of time-dependent strains and stresses due to swelling considering elastic and viskoplastic behaviour. Furthermore an anisotropic swelling behaviour can be considered. This constitutive model was implemented within a numerical computation program according to the finite element method and calibrated on the basis of the results of measurements in the investigation drift of the Freudenstein tunnel which is completely located in the unleached Gypsum Keuper. A parameter combination could be found which results in a good agreement between numerical solutions and results of measurements. Therewith an analysis procedure which enables the design of tunnels in swelling rock is available. ZUSAMMENFASSUNG: Im vorliegenden Beitrag wird ein dreidimensionales Quellgesetz vorgestellt, das nach derzeitigem Kenntnisstand sowohl auf das osmotische Quellen von Tonsteinen als auch auf das Quellen anhydrithaltiger Ton- beziehungsweise Schluffsteine anwendbar ist. Das Stoffgesetz wurde in ein Finite-Elemente-Programm implementiert und anhand von Meßergebnissen des im unausgelaugten Gipskeuper liegenden Untersuchungsstollens des Freudensteintunnels kalibriert. Es ist gelungen, eine Kennwertkombination zu finden, mit der alle Meßergebnisse gut beschrieben werden können. Damit steht ein Bemessungsverfahren für Tunnel in quellfähigem Gebirge zur Verfügung. RÉSUMÉ: Dans l'article présent un loi de gonflement à trois dimensions est présenté, qui peut être appliqué aussi bien au gonflement osmotique de l'argile compactée q'au gonflement de l'argile compactée ou du limon compacté contenant de l'anhydrite. Le loi de comportement était implémenté dans un programme numérique d'éléments finis et calibré avec des résultats de mesures de la galerie de recherche du tunnel de Freudenstein, situé dans le Keuper de gypse non lessivé. On est réussi à trouver une combinaison de paramètres avec laquelle tous les résultats de mesures peuvent être bien décrits. Par ce moyen, une méthode de dimensionnement existe pour des tunnels dans de la roche capable de gonfler.

Jan 1, 2003

By D. Brunner

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By M. S. Klima, P. T. Luckie

Proper analysis of washabiity data can lead to the development of a maximum yield coal preparation plant flow sheet. Simulations, as simple as spreadsheet mass and water balancing, are important in examining yield maximization and middlings liberation. Key to such attribute tracking flow sheet simulations is the distribution model, expressing the probability of a species reporting to the product stream. There are many such models in the literature. This paper examines a functional form that can represent or fit most of the proposed distribution functions.

Feb 24, 1997

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin (1961) were the first to develop a model for bubble-particle interaction in flotation from first principles by considering the surface forces in wetting (or flotation) films. The model predicted that the energy barriers to bubble-particle attachment arise from the ζ-potentials of fine particles, which corroborates well with an earlier work of Fuerstenau (1957) reported for the flotation of quartz using dodecyl ammonium acetate (DAA) as collector. In the present work, a series of surface force measurements have been conducted by accurately monitoring the changes in bubble curvature during bubble-silica surface interactions. The curvature changes are then used to determine the capillary force, which is the sum of the hydrodynamic and surface forces. By subtracting the former that can also be determined from the curvature changes, one obtains the surface forces (or disjoining pressure). The results obtained as functions of pH and collector concentrations show that control of the ζ-potentials of bubbles relative to those of the silica surfaces is critical for maximizing the negative disjoining pressure, which is conducive to promoting bubble-particle attachment in flotation.

By Meissner, C. A.

THE tendency all over Europe, just as it is with us, is to go to the use of turbines for new construction or replacement of old steam or even gas engines. 'The lower construction cost and the lower operating cost, when they can have high steam temperatures and pressures, together with their efficiency, is the cause of this change to turbines, both high and low pressure. The present trend is to equip plants with modern, efficient steam boilers, turbines, etc., and gradually work into high-pressure superheated steam equipment to accomplish a saving. One company has just completed a 375 to 400 lb., 700 deg. superheated steam installation and turbo-blowers with this end in view. Some of our new steam plants are using 350 lb. working pressure.

Jan 1, 1928

Stope support systems, typically consisting of props and packs, are used extensively in the gold and platinum mining industry to stabilize the rock mass in the excavation vicinity and to reduce the hazard associated with rockfalls and rockbursts. The design of stope support systems was historically based predominantly on past experience and practices, and cost considerations. The recent development of a new and improved support design methodology, has led to the potential for significant increases in worker safety and support cost savings. This paper reviews some of the fundamental rock mass and support criteria that form the basis of the improved support design methodology. The considered design criteria are the height of potential fall; quasi-static stope closure rates; dynamic stope closure rates; compressive hangingwall stresses; discontinuity spacing, orientation and interface properties; effect of support length (stoping width); effect of compression rate; consistency of support performance; a real coverage; support spacing; and zone of support influence. The proposed support design methodology combines both the zone of influence and key block stability theories, resulting in optimized support systems for rockfall and rockburst conditions. The site-specific methodology consists of two stages: (i) a tributary area analysis, and (ii) a zone of support influence and a stability analysis, considering hangingwall failure due to buckling, shear and block rotation, which gives maximum safe spacing of individual support units. The methodology is suitable for designing support systems for both blocky hangingwalls and hangingwalls fragmented by face-parallel extension and shear fractures.

Jan 1, 2001

By Jack E. Bailey

From a start in 1957, milling 3,000 TPD of copper ore, the Cyprus Pima Mining Company, which is located 20 miles south of Tucson, has expanded its operations four times, and is currently treating over 55,000 TPD of ore.1 The most recent expansion added a 14,000 TPD semi-autogenous concentrator to the operation. Shortly after startup in January, 1972, the semi -autogenous plant exceeded the designed tonnage rate.2 Ore from the mine is delivered to a 54 inch gyratory crusher and is reduced to a minus 8 inch product. From the crusher the ore is stacked on a surge pile and then reclaimed and fed to the two parallel grinding circuits. A 28 ft. diameter by 12 ft. long semi-autogenous mill and a 16.5 ft. diameter by 19 ft. long ball mill make up each grinding circuit. The semi-autogenous mills are in closed circuit with screens and the ball mill circuits are closed with hydro- cyclones. Rougher flotation follows the grinding operation. Concentrate regrinding and cleaner flotation is performed in Mill I, the older mill. The generalized flowsheet is shown in Figure 1.

Jan 1, 1975

By Ruxton B. P, Rhodes J. M

Two Rb-Sr ages are discernible in data concerning the leucocratic granite which is the youngest pre-sedimentation phase of the crystalline basement complex at Rum Jungle, Northern Territory, Australia. Whole-rockdata suggest that intrusion of this unit took place at about 2400 my ago, with a probable initial ratio around o·707; whole rock-potassium feldspar tie-lines indicate redistribution of strontium at about 1800 my ago. The former age correlates with other measurements on rocks which form basement to the mantling Pine Creek Geosyncline; the latter correlates also with isotopic evidence for regional metamorphism and emplacement of some younger intrusive granites elsewhere within the geosyncline. A few K-Ar ages, from scattered localities, conform generally with the later event or events which appear to have some connection with the structural deformation clearly observable both in the complex and the surrounding metasediments. It is these younger events which appear to match the residual evidence for the earliest detectable concentration of uranium minerals in the Alligator Rivers district.

Jan 1, 1977

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

I. THE ENERGY CRISIS STILL EXISTS A. ALTHOUGH IMMEDIATE SHORTAGE IS NOW ALLEVIATED BY: 1. Increased imports through lifting of Arabian embargo; a. Imports were 6.5 million bpd during the week ended January 17, or 1.3 million bpd higher than last year. b. 1.7 million bpd higher than March '74. 2. Decreased demand resulting from higher prices and conservation. a. January 1975 demand was 17.9 million bpd, 0.1 million bpd lower than January 1973 and … b. 2.0 million bpd, or 10% under originally projected demands for January 1975. c. Gasoline (excluding tax) went up 59% from 27d/gal in August 1973 to 43c/gal in September 1974. d. Gasoline demand for January 1975 was 6.3 million bpd, 0.1 million bpd higher than 1973 but 0.7 million bpd ( 10% ) under projected demand. 3. Increased crude and major product inventories. a. January 17, 1975 crude and major product inventory was 794 million bbl, 99 million bbl higher than the same date in 1973. b. 105 million bbl increase since April 12, compared to only 38 million bbl increase during the same period in 1973.

Jan 5, 1975