Search Documents

By N. E. Yasitli

There is a considerable amount of lignite reserve in the form of thick seams in Turkey. It is rather complicated to predict the characteristics of strata response to mining operation in thick seams. However, a comprehensive evaluation of ground behaviour is a prerequisite for maintaining an efficient production, especially when top coal winning by means of caving behind the face is applied. A comprehensive modelling of deformations and induced stresses is vital for the selection of optimum production strategy. In this study, numerical modelling and analysis of a longwall panel at Omerler underground coalmine have been carried out by using the software called FLAC3D developed based on the finite difference technique. Firstly, a 3-D numerical model of the M3 panel has been prepared. Secondly, induced stresses formed around the longwall face have been determined as a function of face advance where the face was located at the bottom of thick coal-seam. Results obtained from modelling studies have revealed that the front abutment vertical stress was maximum at 7 metres in front of the face and magnitude of front abutment stress was found to increase up to a distance of 200 metres away from the face start line. As the face was further advanced after 200 m from the face start line, there was not any significant change in the characteristics of front abutment stresses. Results of numerical analysis of the panel were in good agreement with in situ observations.

Jan 1, 2005

By Fred R. Biggs

This report was prepared by the U.S. Bureau of Mines to present a brief history of the listing of Iron Mountain Mine as a Superfund site on the National Priorities List (NPL) and subsequent remedial actions. The mine area is located on 4,400 acres near Redding, CA, and includes underground workings, an open-pit area, waste rock dumps, and tailings piles. This property involves multiple sources of acid mine drainage (AMD) that are high in copper, zinc, and cadmium. The selected remedial actions, based on the Record of Decision of 1986, would partially cap the Richmond mineralized zone to reduce infiltration of clean water, divert clean surface waters away from contaminated areas, fill surface subsidence areas, and enlarge the Spring Creek debris dam to provide increased surge capacity. Site remediation efforts at Iron Mountain are well into the remedial design-remedial action phase. Costs to date for remedial action are $7.5 million. Details of activities and designs of remedial elements are presented and future activities discussed.

Jan 1, 1991

By AIME AIME

THE second session on geophysical prospecting at the February meeting of the Institute was a discussion of the mining law and the bearing of the new method of search on location of claims and assessment work thereon. Allen H. Rogers was chairman of the meeting, which he opened by reviewing the present law and the proposed changes. W. R. Ingalls commented (by letter) on the Arentz bill, as introduced into the House of Representatives in 1921 and the need for revision of the present mining law. L. W. Douglas explained (by letter) the bill that he introduced and which has been passed by the House. SAMUEL S. ARENTZ, Nevada: It is my opinion that if the American Institute of Mining and Metallurgical Engineers is to sell this proposition to the people in the West, they have to sell it to the lawyers, because, after all, they are heard loudly when it comes to speaking in Congress. One man tells the other, "This thing is a vicious piece of legislation"; it might not be, but they will pass it on if it affects them. If the Institute would impress on the people affected that we need a re-codification of the mining law and that such is necessary along certain lines; that things have changed during the past decade or two, so today instead of doing our prospecting alone through the sinking of a shaft, through a discovery that may be seen, we are now moving on to more modern means of discovery through geophysics, through the churn-drill, through geology, through geological inference, I think we could get somewhere.

Jan 1, 1929

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By Desmond Y. M. Lee

This paper presents a procedure to prepare input for the computerized pit design system at Iron Ore Company of Canada. The procedure is simple and requires very little training. Also, it is general enough to accept both bench (horizontal cross section) maps and section (vertical cross section) maps. The output of this procedure is data which represent blocks of ore and waste with dollar values based on mineral content. The ultimate pit design is presented in printer-generated graphs, with numbers indicating the depths of pit bottom walls. Roads are added manually by the engineer with the aid of other computer programs. Section maps and bench maps are also printed as part of the output of the ultimate pit design.

Jan 1, 1978

By R. Elliott, H. Bayati

"Effect of time and temperature on microstructure and mechanical properties of an austempered ductile iron, ADI, of composition 3.6%C, 2.6%Si, 0.4%Cu, 0.2%Mn are reported. Xray analysis and. microstructural observations indicate that lowering the working temperature, aging temperature, increases the lifetime of ADI significantly. Results show· that lowering the aging temperature increases the strength and reduces the ductility of ADI. DSC traces for ADI austempered at 340°C are presented. Comparison of the DSC analysis and kinetic measurements demonstrates that the DSC traces can be· used to predict the life time of ADI successfully.IntroductionAustempered ductile iron, ADI, is one of the most significant developments in cast iron technology over the past two decades. Outstanding properties of high yield, ultimate strength, ductility, fatigue and wear· resistance make ADI suitable for a range of applications including gears, connecting rods, crankshafts and agriculture machine components. The austempering reaction in cast iron occurs in two stages, Fig. I, in contrast to the single stage reaction in steel. In stage I the relatively low carbon austenite produced during austenitising transforms into ferritic plates and high carbon austenite, a metastable structure called·ausferrite. The high carbon ailstenite and supersaturated ferrite produced in stage I decompose into ferrite and carbide in stage II: to form a structure similar to the bainitic structure in steel. This behaviour exposes a well-defined processing window, t1 - t2, over which the maximum amount of ausferrite is produced, Figure 1. Whereas the bainitic structure determines the properties of austempered steel, ADI properties are mainly affected by volume fraction of retained austenite (VRA), austenite carbon content (ACC), unreacted or martensite volume fraction (UA V), compositiori and amount of carbides, and morphology of ferritic plates[l,2]. Due to the detrimental .effect of martensite and carbides on properties of ADI, an ideal structure of ADI consists only of ausferrite [l,2]. Thus, it is common to determine the processing window for each austempering treatment in order to identify the optimized austempering time. Decomposition of austenite (stage II) signals the end of the life time for an ADI component, therefore, the aging behaviour of ADI at different working conditions can be studied by determining the t2."

Jan 1, 2000

By Michael Mann

Two house trailers and a modem modular house, all pillar-supported with cantilevered perimeters, were monitored for structural response to vibrations from surface coal mine blasts. Due to the large blast site distances, peak particle velocities measured in the ground beside the houses did not exceed 0.32 ips, and airblasts did not exceed 106 dB. However, the structures responded significantly to the ground vibrations, with maximum high-comer amplification factors as high as 8.5 in the horizontal directions. Vertical structural responses were as high as 10 times the vertical peak particle velocities in the ground, but appeared to be driven more by horizontal ground motions. No measurable airblast responses were observed. The natural frequencies of the structures ranged from 5 to 10 Hz.

Jan 1, 2000

By Jörg Fischer-Bühner

Conventional 22ct Au jewellery alloys are comparably soft in the as-cast and soft-annealed state and hardening by cold-working is the only way of giving strength to the jewellery. The paper first focuses on hardening of 22ct jewellery alloys by conventional means, i.e. solid solution hardening with base metals (aiming particularly at an increased as-cast hardness) as well as precipitation hardening by alloying with base metals beyond the solubility limits and subsequent age-hardening heat treatment. Co-additions of ~2% turned out to result in most pronounced solid solution hardening up to ~100 HV1 in an investment cast & quenched state. Subsequent heat treatments, consisting of solution annealing at 850°C for 1h followed by water quenching and ageing at 300°C ? 400°C for ~ 1h lead to pronounced age-hardening with a peak hardness of ~ 260 HV1. In contrast, 22ct Au alloyed with Ni, Fe or Sb display no age-hardening effect within the same range of heat treatment parameters. The 2nd part of the paper reports on some preliminary trials to enhance the hardening effect of the base metals by additions of suitable elements, which possess a strong tendency to phase formation with the added base metal during ageing treatments. It is shown, that the age-hardening behavior of 22ct and 990/995 Au alloyed with Co or Ni can be remarkably influenced by additions of Sb. A total of only 10wt%0 of CoSb or NiSb-additions lead to a peak hardness of ~ 150 HV1 for a 22ct Au and ~ 100-120 HV1 for 990 Au , which is obtained already after very short ageing times (20-40min) at 300-400°C after solution annealing at 700°C / 1h / water quenching. It is suggested that the age-hardening mechanism in these alloys consists in precipitation of intermetallic CoSb- and NiSb-phases.

Oct 1, 2003

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By J. Warmbrodt, D. Apel, D. Nutakor, L. Grayson, M. Hilgers

MinerSIM is an augmented reality system with integrated hypermedia that is suitable for training underground miners in the basics of using a jackleg drill to install rock bolts. While statistical evidence shows that rock bolting with such a drill has an inherent level of risk, it is conjectured that this can be mediated with adequate safety training outside of the actual mine environment using a variety of educational media including interactive three-dimensional images, games, animations, and videos to describe the mechanics of rock bolting and its principles. Ultimately, trainees will install rock bolts in an immersive environment mixed with real and virtual images generated via a gaming graphics engine. This paper will discuss considerations, implementation issues, and evaluation methodologies of the MinerSIM system.

Jan 1, 2007

By Martin Banda, Gift C. Chisakuta, Moses Chabinga

KCM made a major modification to the Nchanga Tailings Leach Plant (TLP) changing the circuit from feeding post leach thickeners in parallel with leach discharge for solid ?liquid separation to a Counter Current Decantation (CCD) configuration utilising most of the existing equipment. The new circuit is aimed at improving copper recovery from approximately 70% to 79% through enhanced wash efficiency. The re-introduction of CCD circuit at elevated throughput of 46 000-tpd design was made possible due to the EIMCO E-Duc technology design which is an auto-dilution system that enhances solids settling rate. Commissioning (manual operation) which accommodated on-going operational requirements was phased and completed in January 2004. The circuit stabilised in subsequent months and in March alone an all time record copper recovery of 81.8% was achieved which contributed an extra 779 tonnes copper above the plant?s projected production plans. 100% of the project cost was paid back by end of April 2004 This paper discusses the work involved and the challenges faced during the re-commission

Jan 1, 2005

By Wesley W. Eckles

Microcomputer technology has begun to revolutionize petroleum engineering. Petroleum engineers' use of relatively inexpensive personal computers (PC's) is likely to continue expanding rapidly. Since 1982 SPE's Microcomputer Applications Committee has developed a Society-wide users group, a bi-monthly newsletter (MICROCOMP NEWS), an SPE Short Course, a hardware and software distribution program, and a world wide electronic network (SPE NET). The purpose of this paper is to share SPE's experience in creating a dynamic program for meeting the individual member's need in the application of microcomputers to petroleum engineering. My hope is that this will encourage other engineering and scientific organizations to provide similar programs for their members.

Jan 1, 1985

By M. H. B. Nasseri

Barre granite?s samples have been tested for fracture toughness under mode I along two different directions with respect to microstructural fabrics were investigated. 3D objects counter algorithm technique is applied on micro CT images to identify physical properties such as crack induced porosity, crack density, generated total surface area and contribution of individual mineral grains within the damaged zone.The result obtained justifies very well the fracture toughness anisotropy in Barre granite, and explains the difference in the structure of the damage zone evolving as a result of test crack interacting with pre-existing microstructural fabrics. The present study has potential application in the fields of rock mass stability, oil reservoir stimulation, rock fragmentation and damage in blasting and emplacement of dykes.

May 1, 2009

By Yang Ge, Yuzhu Pan, Mansheng Chu, Jue Tang, Cong Feng, Lihua Gao, Zhenggen Liu

The low-grade nickel laterite ore used in this study was successfully upgraded through selective reduction by industrialized rotary kilns followed by magnetic separation. The results indicated that both iron metallization extent and nickel metallization extent showed obvious linear correlation. In addition, rational roasting temperature and prolonged grinding time could enhance the overall fineness level of reduced laterite nickel ore. The moderate roasting temperature at a range of 1100–1150 °C should be suitable enough to a conversion of total nickel to metallic nickel and partly inhibited the conversion of total iron. Ultimately, the obtained ferronickel alloy with a nickel content of 7.32% and an iron content of 84.15% was prepared successfully from the lowgrade nickel laterite ore containing a nickel content of 1.92%. Nickel and iron recoveries were 96.72 and 89.08% respectively, which achieved the highly efficient recovery and utilization of iron and nickel from low-grade laterite nickel ore

By L. A. Matthews

The embrittlement of the Ti-6Al-4V alloy by hydrogen dosing at elevated temperature has been investigated. Metal coupons were subjected to isothermal treatments in a partial hydrogen atmosphere in the temperature range from 650ºC?950ºC and the degree of embrittlement after treatment was determined by drop-weight impact testing. Embrittlement was found to be inversely related to reaction temperature as a result of the combined effects of greater hydrogen absorption and titanium hydride precipitation at the lower isothermal temperatures. Keywords Titanium, hydrogen embrittlement, impact energy

Jan 1, 2011

By A. Flemming

"As the next century draws near, new mine properties must be brought into production to replace existing operations that are approaching their economic life. This paper presents some of the critical technical issues being addressed by Manalta Coal Ltd. as they strive to bring the Telkwa Coal Project near Smithers, BC into production during the year 2000. The mine is planned to produce between 1.0 to 1.5 million tonnes per year of medium volatile coal for export to overseas thermal and PCI markets. IntroductionManalta Coal Ltd. (Manalta) is proposing the development and operation of a surface coal mine and associated infrastructure approximately six kilometres southwest of the village of Telkwa, British Columbia (Fig. 1). The infrastructure consists of a coal washing facility, tailings disposal area, clean coal haul road, access road and rail loadout facility. Over a 25-year period, the mine is expected to produce between 25 and 37 million clean tonnes of coal primarily for the export market.To achieve public and governmental approval for the development, the project will be reviewed under British Columbia’s Environmental Assessment Act. Manalta entered the formal Assessment process in February 1, 1997 with the submission of an Application for a Project Approval Certificate for the Telkwa Coal Project."

Jan 1, 1997

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By R. C. Keaney

The metals industry is in complete chaos with mines being shut down, profits becoming non-existent, and continual losses to imports from other countries. Yet the raw material supplier to the glass industry has many opportunities to grow and to produce profits. Fortunately, the cost of most glass raw materials are low enough that competition from imports is not anywhere as critical as it is in the metal industries, such as copper, aluminum, lead, and others. But the glass raw material supplier must develop new products, both chemically and physically, to effectively compete in the future. The purpose of this paper is to point out generally where these opportunities exist and to suggest how they may be further developed. As the glass industry looks for energy saving materials, they look once again towards finer materials. A glass furnace is now approximately 40% efficient. Glass engineers are constantly striving for energy savings and it is well known that finer materials melt easier so that the manufacturer can operate his furnace either at lower temperatures for the same production or he can produce more material at the same temperature. The old 20 mesh sand specification is no longer sacred and as the mesh size for sand changes so do the specifications for all other raw materials used in the melting process. Highly instrumented glass furnaces can now measure quite accurately the energy needs to produce glass and can also measure the energy loss in each furnace. Glass technologists desire today a sand with a top size of 40 mesh while some would like to have the top at 60 mesh. This becomes more difficult to accomplish as a raw material supplier without .grinding. As you well know, grinding develops fines. Yet the same technologists will tell us that we can have nothing passing a 140 mesh screen. Therefore, we must develop processes which allows us to produce a finer screen size without increasing the amount of fines passing through the 140 mesh screen. To counteract this, different and changing industries are now demanding much finer products so possibly there will be markets for the fines which are currently separated out of the products. Methods that are practical and low cost must be found to develop different products with different screen specifications. What works for sand can be carried over to the other raw materials used in melting. Among the answers to finer products, of course, are pellets. Aglomeration or pelletizing has been looked at in the past and will be looked at in the future. Considerable work has been done in the glass container industry on this and must be carried out more extensively. By using aglomerated material or pellets, the glass producer will gain the benefits of melting fine materials without suffering from handling or dust problems. Pelletizing, particularly where using basic glass melting materials such as burned lime or sodium silicate, will not only produce a good pellets but will add desirable minerals to the glass batch.

Jan 1, 1986

By E Villaescusa, A Kusui, R Talebi, R Hassell, C Arcaro

Northern Star Resources (NSR) operates several seismically active mines as part of its Kalgoorlie Operations. In order to successfully continue mining at depth in increasing stress conditions, strategies need to be developed to reduce, control and manage the impact of seismicity causing damage to the rock mass. Consequently, a research partnership was developed with the WA School of Mines (WASM) through Mining3. The main aim of the project was to develop appropriate ground support standards that could withstand the expected dynamic response with minimal to no rehabilitation required for the life of that excavation. The project utilised a design methodology for determining the required energy demand based on detailed geotechnical mapping, probabilistic analysis of wedge formation and an estimate of rock ejection velocity based on uniaxial compressive strength of the intact rock (Villaescusa et al. 2016). The ground support scheme consists of high tensile chain link mesh, resin encapsulated de-coupled posimix bolts and plain strand cable bolts, in one, or multiple passes together with plain shotcrete. Implementation of the design posed several challenges including how to install the chain link mesh, maintaining the required productivity, ensuring quality control, and understanding the interaction of the several ground support components within the scheme. The implementation of the system within a trial area was successful from development mining to open stope extraction. The most significant field verification of the system occurred with near field M+1.9 seismic occurring in proximity to an operating long-hole drill. Despite large displacements exceeding 0.5m in places, there was no significant ejection of rock or failure of the ground support system. Following the successful trial, the ground support design methodology and standards have been implemented across several NSR sites. The system forms the basis for the successful extraction of resources in future high seismic risk areas.

Mar 15, 2021

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014