Search Documents

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By J. F. McCoy

The quantitative determination of the mass rate of flow of methane in an underground airway is calculated as the product of the methane concentration and the air flow rate. Velocities are taken at several points and then averaged over the airway cross section to determine the total volume flow. Errors in velocity measurement thereby result in errors in total volume flow as well as the mass flow rate of methane. The purpose of this program was to evaluate existing instrumentation for measuring air velocities in the speed range under 2000 feet per minute; to evaluate the method for determining total air volume flow from the velocity measurements; to evaluate new techniques which may be applied to measuring air velocities; and to design a prototype instrument which represents the best technique based on the evaluation. The instrument should be: a. portable b. self-contained c. insensitive to dust, moisture and temperature changes d. safe for use in gassy mines

Jan 1, 1972

By Felipe Henríquez, Daniel Silva

"Traditionally, the implementation of an automated advanced process controller in any mineral processing complex is a challenge, mainly due to the quality of resources and technologies required, the uniqueness of each control solution and the uncertainty of the engineering hours needed to complete the task. Thus, the use of advanced and proven control technology becomes a key factor when deploying the control strategy. However, success would still not be possible without the presence of common sense, process knowledge and fundamental process data. Minera Los Pelambres, taking advantage of such factors and its accumulated process experience, implemented a novel and successful combination of MPC (Multivariable Predictive Control) and advanced control for secondary grinding and regrinding stages at its copper concentrator plant. In both cases, the control objectives are: being capable of processing a variable feed from the upstream process while at the same time avoiding to become a process bottle neck and yet, maintaining an adequate product quality (in terms of size distribution) to the process downstream. Additionally, for the case of the vertical regrinding mill (vertimill), the control system should also be capable of keeping an adequate circulation load and making an efficient use of the available grinding power. In either case, extending hidrocyclones availability while maintaining their performance is a must, since both factors are required for process and maintenance purposes. Thus, the process control problem becomes one with a multi-variable type of process with multiple control objectives to satisfy simultaneously. In trying to solve it, many mineral processing operations have implemented basic or conventional control or even better yet, expert systems. Minera Los Pelambres believes that better and faster results can be achieved using a combination of MPC and advanced control. Such strategy was successfully implemented, reducing considerably process variability while maintaining high throughput and keeping the process well within constraints limits. Their control philosophy, implementation process, main results and their key performance indicators are discussed here."

Jan 1, 2014

By Teresa M. Bodas Freitas, Arianna Lupattelli, Peter J. Bourne-Webb, Diana Salciarini, Martina Zito, Donatella Sterpi

The thermomechanical response of thermally-activated (TA) piles under monotonic thermal loads is quite well understood and the remaining uncertainties relate to the effect of long-term, cyclic loading of individual TA piles and pile groups. Recent studies undertaken by the authors have provided insights into the behaviour of TA pile foundations undergoing cyclic thermal loading. Despite their simplicity, the analyses show that key aspects of the observed response of piles in sand, under cyclic thermal loading can be reproduced, providing confidence in the outcomes of the analyses. The studies examined isolated piles and pile groups, and concluded that irrecoverable thermally-induced settlement may be mitigated through the choice of an appropriate margin of safety on the pile shaft resistance under service mechanical load conditions, and the maximum thermal stress can also be readily estimated. This paper consolidates these works and provides guidance regarding the safe geotechnical and structural design of the piles, then looks towards the remaining issues around the safe provision of thermally-activated pile foundations.

May 1, 2022

By F. S. Crawford

Companies which have been engaged in safety work for a number of years are becoming increasingly aware of the fact that it is not enough to supply guards for various pieces of machinery and equipment and to supply safety inspection to see that rules are being carried out. Studies of many safety organizations have demonstrated that the accidents which could have been prevented by proper guards constitute only a small percentage of the total acci- dents, and amount to perhaps not more than 15 per cent. Evidently, if success is to be attained in preventing all accidents which it is humanly possible to prevent, a company must have the cooperation of every employee. Mining particularly presents probably the greatest hazards of any industry. Prevention of accidents. is made increasingly difficult because men often work alone, although generally in pairs, and only in the concentrated systems of mining do they usually work in groups of more than three or four. Supervision is difficult, therefore, and much reliance must be placed upon the individual workmen. In mining, as perhaps in no other occupation, it is of the greatest importance that individual workmen should receive continuous safety education. Within the last few years safety education has come to the front as one of the most important of accident-prevention measures, although it is true that its importance has been repeatedly stressed by the United States Bureau of Mines and other national safety organizations since the inception of the safety movement many years ago. A review of the safety educational methods of some companies in the Lake Superior district should be of interest. Perhaps better methods are in use in other parts of the country, but the methods shown have been instrumental in many cases in reducing the number of accidents. In one mine in the district whose methods are described the frequency of accidents has been reduced to zero within the last two years. A number of other mines in the district have recently gone into the class having no lost-time accidents for considerable periods of time. One company in the Lake Superior region, operating over 30 mines, succeeded during one month of 1930 in operating every mine without having a single accident which caused lost time beyond the day of the injury. Records like these are increasing in number, and while it is believed that they are the combined result of different means of safety activity, it is undoubtedly true that many of these results were obtained through safety educational methods.

Sep 1, 1931

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

Jan 1, 1886

By R. A. Cattell

The Bureau of Mines actively conducted a well-coordinated research pro- gram during the past fiscal year on problems dealing with the production of oil and gas, transportation of natural gas, chemistry and refining of petrole- um, thermodynamic properties of hydrocarbons, and the processing and utiliza- tion of incombustible helium gas. These particular reserach phases, compris- ing the presently scheduled activities, are integral parts of a broad program selected soon after the war as suitable for Bureau of Mines study, to meet immediate needs for specific information on petroleum and natural-gas problems of national scope. Important progress was made and many technical reports were finished during the year. Several reports were published on gas-condensate production problems, one giving the results of laboratory tests of relative merits of various steels and alloys for rosisting the corrosion that occurs in high-pressure gas- condensate wells. Research was continued, using the Bureau's windowed cell, to determine the characteristics of gas-condensate fluids, and an important paper on the phase relations of these fluids at low temperatures was published. An important part of the Bureau of Mines petroleum production research program for many yoars has been the engineering study of type oil fields. This year reports waro completed on the Lake Creek, Sheridan, and West Rod River fields, Tex.; the Atlanta field, Ark.; and the Bogge field, W.V. Othor fields under study and for which reports will be issued are the Carthage and Now Hope fields, Tex., and the Weber pool, Okla. Spocial studios to determine the characteristics of the oil-gas solutions as they exist within the native reservoir rocks have been in progress in the North Lindsay field, Okla.; the Elk Basin field, Wyo. and Mont.; and the Rangely field, Colo. The North Lindsay study brought to light several un- usual physical proporties of the oil as it is found in this deep-seated reservoir. For instance, its viscosity is less than that of water, and more than 2 barrels of the initial reservoir oil must be produced to yield 1 barrel of "stock-tank oil." In the Elk Basin and Rangoly fields the oil-gas solution varies in composition within the reservoir, depending upon structural location. Engineering studies were continued on woll spacing and on drilling fluids with special emphasis on obtaining uncontaminated cores, or coros for which the flushing action of the drilling fluid can be dotormined accurately. In connection with research on production of oil by secondary recovery methods, progress was made in studies of conditioning water for subsurface injoction, of input ratos and pressures for water-flooding oil sands, and of the selective plugging the more permeable mediurs to prevent or retard channel- ing of the injected fluid. The availability of fuels for all types of internal-combustion engines still is tho primary resoarch project in potroleum chomistry and refining. This rosearch program is subdivided into a sorios of problems under four main topics: (1) Raw-material studios; (2) relationships of fuel consumption, proporties, and performanco; (3) utilization of potroleum products; and (4) analytical mothods, which include chomical and physical property detorminations.

Dec 1, 1949

In-pit crushing and conveying (IPCC) is being increasingly considered as an alternative to traditional truck-shovel mining methods. The move towards IPCC is driven by a number of factors including the potential to reduce greenhouse gas emissions, the availability of skilled labour and the need to increase extraction rates to levels that present significant challenges to traditional methods.When considering the relative performance of IPCC and truck-shovel methods, the outcome can be inadvertently impacted by either the use of different simulation approaches, or techniques that do not adequately model the processes in sufficient detail.A simulation approach is proposed that models both IPCC and truck-shovel using the same software platform and is capable of functioning at a wide range of resolutions from life-of-mine scale through to second-by-second asset tracking level. The simulation framework also holds models of processing equipment and hence the mining simulations can be extended to gauge the impact on downstream plant.The approach, known as mine-process operational simulation (MPOS), can be tailored to the level of information available and hence the type of study required, ie order of magnitude, prefeasibility, feasibility, or detailed design.Using information from block models and a range of detailed equipment and process models, MPOS can span major system discontinuities, typified by the mine-plant interface, to allow the estimation of final mine and plant product specifications.

Dec 6, 2010

By J. R. R. Bowling, A. McFadden, M. Francoeur

The abstract discusses the increasing use of extensive duct-fan systems in underground hard-rock mine development. It highlights the challenges of designing these systems, particularly the risk of partial vacuum and the need for careful booster fan positioning. The paper explores factors influencing the design of these systems, including component limitations, operational wear margins, and power constraints. It also defines the concept of partial vacuum and its impact on ventilation ducts. The authors propose an algorithmic approach for specifying the location and blade pitch of in-line booster fans to prevent system failure.

Mar 17, 2022

By B. M. Eiter

The impact of fatigue is seen not only in its effect on the job performance of haul truck operators but also on the health of the operator and the productivity at the mine site. Its impact can even extend outside of the mine site to the health and well-being of the surrounding community (Fourie et al., 2010). In this paper, a case study of a small, surface mining organization is presented. The goal is to highlight the fatigue risk management system implemented at the studied mine site. Mine safety personnel who were interviewed discuss the changes made to the infrastructure of the mine, to administrative areas such as the number of shifts and the use of vacation time, as well as the implementation of new technology into haulage vehicles. This paper reviews how these changes are supported in the research literature.

By S. H. Lorain

This paper, which describes lode gold mining in Idaho county, Idaho, is one of a series on western mining districts being published by the Bureau of Mines. It describes mining and milling practices, gives costs, and discusses transportation, climate, power, labor, and other conditions that affect them. The materiel upon which the paper was based was gathered during a field survey in the summer of 1937.

Jan 1, 1938

By D. E. Wolfson

As a part of its overall program of coal carbonization, the Bureau of Mines is studying the coking properties of coals that may be used for metallurgical purposes. The objectives of this study were given in detail in a previous report.2/ The inherent suitability of coal for metallurgical use depends primarily on (1) chemical composition, (2) preparation characteristics, and (3) carbonization behavior. The first two factors, as well as the available reserves, are considered in selecting coals for carbonization tests.

Jan 1, 1957

By MEHMET KIZIL, PETER KNIGHTS, ROYAL REA

A 1/20 scale experimental dozer push test rig was designed and constructed to quantify the expected production rates (loose cubic metres per hour) for dozers operating in hard rock bulk push applications. The particle size distribution of the material employed in the test rig was modelled on a fragmented muckpile representative of that for a typical surface copper/gold mine overburden. A commercially available road base material was found to be highly representative of site conditions. Buckingham Pi theory was applied to mathematically develop factors for scaling up dozer productivity parameters, including blade loads and push times. Dozer production rates were investigated for various dozing distances and slope angles. A series of instantaneous productivity curves were produced which are applicable for use in hard rock dozer push operations. Currently, it is difficult to estimate dozer push productivity in hard rock environments due to dozer productivity correction factors that are empirical in nature and provide only discrete, end-point values for a range of operating conditions. The productivity curves produced demonstrate that dozer productivity declines rapidly over the range of 10 m to 40 m. As such, it is recommended that efficient bulk dozing operations in hard rock mining blocks should not exceed 40 m dozing distance. Further testing of muckpile conditions with increased clay and moisture content would be beneficial in order to better understand and quantify the effects of cohesion on hard rock dozer push productivity.

Nov 23, 2021

By Erik Sundström, Magnus Nygren

Having seen significant improvements to accident rates in the last 40 years, companies in the Swedish mining industry now show a greater focus on the development of safety cultures throughout their organisations and workplaces. However, there is a lack of research examining the different safety initiatives and strategies practiced in the industry today. This study explores the potential influence and consequences such initiatives may have on the development of safety cultures in the Swedish mining industry. Twelve interviews with experts on safety initiatives from four different Swedish mining organisations were conducted and analysed in a process based on qualitative thematic analysis to identify notable connections to safety culture development. The results of these interviews highlight proclivities in the implementation and use of safety initiatives such as subjects of focus, methods and desired effects. This enables the interpretation of the conceptualisation and methods for the development of safety culture in these organisations based on their approaches to safety development. We believe the results of this study can serve as support for discussions on safety culture development in the Swedish mining industry, and be of interest for international mining industries, in addition to approaches to research in this field. However, we also believe it is important to emphasise the opportunities to approach safety culture in mining from different perspectives than those common today.

Jul 19, 2023

By Robert Lee Stahl

Comprehensive field tests were made in the Gas Hills, Wyo., to determine whether surface geophysical techniques could be used to detect and delineate faults in marginal uranium deposits. The tests were made on property owned by Federal American Partners, Gas Hills, Wyo., and included seismic refraction, self-potential, induced polarization, magnetometer, electrical resistivity, airborne infrared thermal scanning, and airborne photography. Of the several geophysical techniques tested in the field, horizontal resistivity profiling with electrode spacings in the range of 25 to 50 feet was most diagnostic of faults. The method is quick, cheap, accurate, and one that can be easily used by personnel employed by mining companies to detect and delineate faults.

Jan 1, 1973

By R McDonough

DTL2 contract C916 was awarded in March 2009 for S$340 M. This contract includes two mass rapid transit (MRT) 1100?m long bored tunnels using two slurry tunnel boring machines (TBMs), with an internal diameter of 5.8?m, two cross passages and 135?m of cut-and-cover tunnels The contract also includes the design and construction of a new underground station including station entrances, subway links, architectural finishes and external landscaping. The station, located at Upper Bukit Timah Road near Jalan Jurong Kechil will also double as a civil defence shelter.The works included significant traffic management in a dense urban area in order to create the working areas whilst keeping the requisite number of traffic lanes. This involved numerous utility diversions and included the removal of a 33-year-old pedestrian overhead bridge (POB) over busy Bukit Timah Road. The station and tunnelling works were completed on time, including a ‘dock and dismantle’ TBM retrieval and subsequent breakthrough of the separating wall.This paper will detail the methods and solutions used to construct the tunnels and stations, with a focus on the requirements for construction of the station to be a civil defence shelter if required. This involved solutions to tying reinforcement and placing concrete to high standards in a restricted space, as well as the incorporation of heavy blast doors and other associated protective measures. The efforts of the management team resulted in the project being awarded first prize in the 2011 Land Transport Authority’s Annual Safety Award Convention and being named winner of the Safety and Health Award Recognition for Projects (SHARP) award at the 2011 Workplace Safety and Health (WSH) Awards. As well, McConnell Dowell won a Green and Gracious Builder Award (Excellent Category) from the Building and Construction Authority (BCA).CITATION:McDonough, R, 2014. Design and construction contract C916 Beauty World Station and Tunnels, Singapore, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 411–418 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By W. J. Kroll

The production of beryllium metal and its alloys is one of the most difficult tasks in metallurgy. In this report we shall examine the progress made in this work- in the last 15 years; taking into account the outstanding publications, including; those of the patent literature, and the information obtained during our 20 years? experience with this metal. The difficulties experienced' in producing elementary beryllium derive from the physical nature as well as from the chemical behavior of the metal and its compounds. Its oxygen affinity is about the same as that of calcium and a little higher than that of magnesium. Its chlorine affinity is much lower than that of magnesium, about equal that, of manganese, and little higher than that of aluminum. The sulfur and nitrogen affinity is probably almost the same as that of calcium for these elements, and beryllium carbide is probably more stable than aluminum carbide, A14C3. The intermetallic affinity of beryllium may be given in descending order, as follows: Nickel - copper - iron. It forms eutectics with -aluminum and silicon as well as with silver. It does not alloy with magnesium and only partly with calcium. Its oxide melts at 2,570° C., but CaO and BaO form readily fusible eutectics with BeO(65).3/ No igneous solvents are known for BeO, which behaves id this regard like Mgo. The beryllium silicate is a strong compound, the aluminete much less so; however, CaO easily displaces Be in the heated mixtures. The Anhydrous chloride hydrolyzes, and it cannot be made from aqueous liquors. It sublimes at 488° C, and melts at 405° C., The fluoride, which, is very Soluble in water, hydrolyzes also, but a kind of oxyfluoride of the approximate formula 2 BeO?5 BeF2 can be made from solutions by dessication. The fluoride melts at 800° C, and boils above 1,100° C. It forms very stable double fluorides with alkalifluorides, which have very low melting points and are fairly soluble in water. They are more stable than the analogous fluosilicates and the sodium fluoaluminate cryolite.

Jan 1, 1945

By Hevina S. Dashwood

This paper proposes to build on my previous research (Dashwood 2012), which analyzed how and why the norm of sustainable development became institutionalized in the global collaborative corporate social responsibility (CSR) initiatives of major mining companies. Since the late 1990s, the majority of major global mining companies have employed the norm of sustainable development to frame their individual CSR policies and to inform industry collaboration at the global level through the International Council on Mining and Metals (ICMM). This paper proposal seeks to address lingering questions from that research, by developing an explanation for how the normative frame of sustainable development has translated into specific CSR standards adopted by the mining industry. Preliminary findings suggest that, although the global mining industry has reached broad consensus on the meaning of sustainable development in the context of mining, there remains considerable variation between mining companies in terms of which specific global standards they adopt. As members of the ICMM, major mining companies are required to report according to the Global Reporting Initiative (GRI) indicators relevant to mining, and there has been wide-spread up-take of the ISO 14,001 environmental management system standard. However, other global standards, such as the International Finance Corporation (IFC) Performance Standards and the Extractive Industry Transparency Initiative, have not been uniformly adopted by the mining industry. What explains this variation? The paper employs a three-level institutional framework (rational choice institutionalism, historical institutionalism and the ?new? institutionalism in organization theory) to explain the influences on the adoption of CSR standards in the global mining sector. Existing research confirms that institutional context is an important factor in explaining CSR adoption in the mining sector (Dashwood 2012). Are similar forces at work in explaining the variation in adoption of specific CSR standards? A three-level institutional analysis lends itself to uncovering influences both external to mining companies (such as pressures from stakeholders), as well as internal company dynamics (such as managerial discretion). Furthermore, the framework can incorporate dynamics operating at the global level (such as isomorphism), the national level (such as the regulatory regime) and the local level (such as community needs and environmental challenges). The theoretical significance of this framework is that the influences on CSR adoption are more complex than can be explained in a single approach (such as narrow rational choice/cost benefit explanations). On a practical level, insights into how global standards get interpreted and acted upon by individual companies could lead to the development of more appropriate and effective global standards.

Aug 1, 2013

By Donald C. Myntti

INTRODUCTION A major segment in a successful heavy equipment maintenance and repair program is the provision of well-laid out and well-equipped shop and service facilities The facilities described here will be those required for a large, high tonnage hard rock open pit mine utilizing rotary drills, shovels, haulage trucks, support equipment, and service trucks. The term support equipment covers the equipment required to support the drill, shovel, and truck operations, these are crawler tractors, road graders, front-end loaders, water trucks, rollers, rubber-tired tractors, etc. Service trucks are the automotive type consisting of rubber-tired over-the- road equipment. The primary structures generally involved in the total maintenance effort are as follows. (1) the main shop with an attached warehouse (the structure could also house the tire and lube shops plus the equipment cleaning stalls), (2) a service station with bulk petroleum product storage tanks, (3) a heating plant, (4) a security station (lf this is a corporate requirement), (5) operating department and employee assembly buildings, and (6) an electrical substation. Under certain conditions, many of these facilities with the exception of the substation could be combined In one or several structures. This arrangement could have a great advantage especially in areas where the heating of the structures is extremely critical.

Jan 1, 1979