Search Documents

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By Arthur Notman

THE raw material men in all industries, and copper is no exception, are accustomed to think of them- selves as the whole show, and not without justice, for if there were no copper mines the world would have no copper. Nevertheless, many different things costing money and resulting in profits must be done to their product before it is ready for the world's use. In other words, they are making the frequent mistake of Chinking in terms of partial costs. Nobody really uses electrolytic copper. Possibly that is why nobody seems willing to pay anything for it. The manufacturers, being canny, do not buy any more electrolytic than they feel that they can work up and sell profitably, although they like to make the raw material men Chink that they will take all that can be produced. This is a state of affairs that has aroused my sympathy and curiosity, and has induced me to study the financial history of the copper wire and brass industry of the country or such portion of it as publishes any records readily available to the curious minded. About 60 per cent of the electrolytic copper used in this country is drawn into wire and consumed by the electrical industries. The remaining 40 per cent is

Jan 1, 1926

Critical safety tools to locate miners underground are featured by several exhibitors at MINExpo. Communication was the buzzword for health and safety products at the 2008 MINExpo, and it is still important in 2012. Products unveiled following the Miner Act in 2006 have been upgraded and improved. Saving lives and reducing injuries through better leadership, planning and practice is the goal of every mine professional.

Jan 1, 2012

Mine drainage and mine reclamation are topics of major interest to the mining industry, federal and local governments, and the general public. This publication and its companion three volumes are the proceedings of a conference held in Pittsburgh, Pennsylvania, April 24-29, 1994. There were twelve sessions (69 papers) that dealt with mine drainage, including modeling, geochemistry, prediction, treatment, control strategies, characterization, hydrology, and case studies. These sessions comprise volumes 1 and 2. The six sessions (34 papers) that dealt with reclamation and revegetation of disturbed lands are included in volume 3. Volume 4 includes the six sessions (34 papers) that dealt with such topical issues as fires at abandoned mine sites, subsidence, hydrology, mine wastes, and policy. Poster session presentations are represented by 49 papers and 92 abstracts that have been placed in the back of volumes 2, 3, and 4, consistent with the subject of that volume.

Jan 1, 1994

By Jeanie Wills, Theresa Nyabeze, Samantha Espley, Donna Beneteau

This presentation reports survey findings that aim to modernize the definition and understanding of the term 'mining.' The survey, conducted via LinkedIn in Winter 2024, garnered responses from a diverse group of individuals, including current or former employees of mining or exploration companies, mining consulting firms, service providers, supplier firms, as well as students and retirees with industry experience. The data, ethically approved by the University of Saskatchewan, offers valuable insights into satisfaction levels within the mining sector and suggests an expansion of the identifying characteristics of definitions of mining. This marks the third CIM gaining insights paper by Beneteau, Espley, and Nyabeze, following previous works on 'Career Satisfaction for Women in Mining' (2010) and 'Mentorship Initiatives in the Canadian Mining Industry' (2018*)."

Oct 1, 2024

By R J. Soriano, S Ciutina

The Masbate gold deposits are situated on the island of Masbate, 350 km south of Manila. A new plant was commissioned in April 2009. The grinding circuit consists of one semi-autogenous (SAG) mill Ø9.75 m × 4.27 m, two ball mills Ø5.6 m × 7.1 m and a pebble crushing circuit, which is usually called a SAG-ball mill-crusher configuration. The SAG mill was originally equipped with radial pulp lifters. The mill runs at fixed speed of 10.9 rev/min, which is approximately 80 per cent of critical speed (per cent CS). Due to the high speed of the mill the original radial design pulp lifters presented a high volume of recirculating load inside the chamber and consequently heavy wear on the outer circle (bottom pan).In order to address the high wear on the pulp lifters a number of avenues were considered in early 2011. The chosen solution was to change the geometry of pulp lifters from radial to curved design. The pre-existing drilling pattern on the discharge end of the mill was a major constraint. A number of designs were considered. The selection of the most suitable option was to be made based on 3D discrete element modelling (DEM) and smoothed particle hydrodynamic (SPH) simulations.The original radial design and two potential solutions for curved pulp lifters were simulated with 3D DEM and SPH software. The main three objectives were predicting the charge dynamics, the expected wear patterns and discharge efficiency. One of the solutions was chosen and implemented during 2012.Observations carried on after installation of the curved pulp lifters have confirmed, as expected, a reduction in wear intensity on the outer pulp lifters. In addition to this, at early stages of operation with curved pulp lifters, the mill operator noticed a reduction in energy consumed by the mill with no detrimental effect on mill performance.This paper is intended to further study the effect of curved pulp lifters on mill energy consumption.CITATION:Ciutina, S and Soriano, R J, 2014. Curved pulp lifters – can they save energy?, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 109–116 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By H. Hitchen

THE object of this paper is to present the various facts that l1ave been revealed during lengthy investigations into the performance of all types of ropes on different hoisting installations. It then goes on to suggest means by which most of these findings could be usefully employed to obtain more economical rope lives with increased safety. SHAFT HOISTING ROPES Four basic designs of ropes are now employed for hoisting duties: (1) Six-strand, round strand ropes with fibre cores. (2) Six-strand, triangular strand ropes with fibre cores. (3) Non-rotating, multi-strand ropes. 0) Locked coil ropes. Round Strand Ropes (Figure 1) Very solid and reliable ropes can be obtained with this simple geo-metric design of strand. 1'1?iangula1? Strand Ropes (Figure 2) Owing to the fact that the wires in the strands are bent over a triangle, they do not seat quite so solidly as when they are bent over a circular core wire, as is the case with

Jan 1, 1963

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To Assist users in the selection of reliable and satisfactory respiratory protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators . The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks , 19B and the amendments to 19B for suppliedair respirators , 21B for dust , fume, and mist respirators , and 23B for chemical cartridge respirators . Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pittsburgh , Pa . , 15213 . Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements , a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an extension of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, however, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's production facilities are maintaining a satisfactory quality control .

Jan 1, 1966

By Pedro Hugo Tumialán

El presente texto señala el proceso de mineralización del yacimiento metálico de Algamarca en Cajamarca a través de la descripción de la singularidad de sus características geológicas. De acuerdo a ello, se corta una inclinal de cuarcita de la formación Chimú del Cretáceo inferior, cuyo eje tiene un rumbo NW concordante al eje del anticlinal. Asimismo, el intrusivo Caupur es el causante de la mineralización de las vetas de Algamarca, las cuales resultaron por fuerza de compresión perpendicular al eje del anticlinal, formando algunas vetas dextrales y sinestrales, así como vetas de tensión perpendiculares al eje anticlinal. En este sentido, las vetas son angostas (O.la 0.3 m)peroricas en plata y su distribución se da en forma de arco de cada veta.

Nov 8, 1982

By Frederic Souche, Andrew R. Klaetsch, Brian Hann, Nick Goodenow

This paper describes support of excavation (SOE) design and construction for three large diameter shafts excavated through glacial soil and controlled blasting in complex sedimentary rock formations. SOE in soil consists of unreinforced secant pile rings designed to resist lateral pressure in circumferential compression, eliminating costly steel core beam reinforcing. Controlled blasting at the shafts, adits, and tunnels in densely populated neighborhoods requires managing risks to the public, buildings, and utilities. Controlled blasting approaches limited adverse impacts to receptors nearby while achieving adequate production and fragmentation. A site-specific observational approach was used to adjust blasting parameters, limiting the impact on local stakeholders while maintaining daily progress and managing overbreak.

Jun 13, 2023

By H. S. Geismer

INTRODUCTION. THERE are three general methods available for obtaining commercial brown iron-ore : hand-screening; washing; and washing and concentrating. Hand-screening has produced a large tonnage of ore in the past, but is rapidly falling into disuse, except as a preliminary step, largely because modern furnace-practice requires all foreign material to be separated from ores before they are delivered to the furnace, and hand-screened ores can rarely be made to fulfill that requirement. Another argument against hand-screening is, that the waste-pile often contains as much ore as the screen recovers. The operation known as hand-screening consists of throwing the ore-bearing material against a stationary inclined screen of 0.5- to 0.75-in. mesh, similar in construction to the screens employed in sand-pits. The recently-prospected brown-ore deposits of Cuba seem to offer possibilities for hand-screening not possessed by the average American deposit, since these ores are not associated with worthless clays. Washing, and washing and concentrating, may be discussed together, since concentrating is never practical on brown iron-ore, except to treat ores that have already been washed. (Strictly speaking, washing might be classed as concentrating, but it is never so designated by brown-ore men.) The various steps of removing ore-bearing material and converting it into ore suitable for blast-furnace use, may be grouped under five heads: loading for transportation ; transporting ; feeding into the washer; washing; and concentrating. These five subjects will be considered in consecutive order. Each of these successive steps may be accomplished in a number of different ways, the choice depending entirely upon the character of the ore-bearing material to be treated.

Aug 1, 1911

Fresh coal refuse was sampled at 21 US mines. Five of the sites were drilled, sampled and tested more extensively. Field tests included Standard Penetration tests, and in-situ density determinations. Laboratory testing included specific gravity, gradation, maximum, and minimum density tests, as well as 9-inch) drained triaxial tests, 9 and 10-inch, permeability tests, slake-durability tests, and accelerated slaking tests. Some refuse sites had significantly lower shear strengths and permeabilities in old, slaked or weathered material than in fresh refuse. Testing did not show useful correlations between strength and permeability changes and other material properties which could serve as "predictors". Testing of refuse under "accelerated slaking" conditions showed promise as a comparative tool and as a potential means of preparing artificially aged samples for evaluations of long-term behavior. The state-of-the-art in slaking research, and the implications of slaking on coal refuse disposal, and on practical methods of managing slaking, were also studied.

Jan 1, 1981

By Rita Michael

"The Marmara Ironworks was not the earliest ironworks in Ontario, but it was distinguished from other early works in a number of ways. It was established on an ambitious scale as a self-sufficient and, for the time, sophisticated community. In effect it was an iron plantation on the scale and scope of those at Hopewell, Pennsylvania and Saugus, Massachusetts(1). It was, besides, the only one of the few early ironworks in Upper Canada which operated almost to the end of the nineteenth century, albeit in fits and starts, and which used magnetic ores rather than bog iron ores (limonite). Furthermore it is the only works which has produced archaeological interest over a number of years. The ironworks is on the east bank of the Crowe River near Highway 7, on Lots 7 and 8, Concession 4, Marmara Township, Hastings County, Ontario. It is the property of the Village of Marmara, and the extant remains encompass about 2. 5 acres of the original 2000 or so which made up the original grant. The mineral riches of the Canadian Shield had been known since the days of the Jesuit missionary-explorers. A consortium headed by Alexander Henry and the Duke of Gloucester planned to exploit the copper near Sault Ste. Marie during the last part of the eighteenth century, but nothing came of the venture(2). This attempt may have grown out of Lord Dorchester's suggestion that private enterprise be encouraged in order that the iron ore which ""abounds"" in Canada might be exploited(3). John Graves Simcoe, the first Lieutenant Governor of Upper Canada was also anxious to see iron working develop. Simcoe was eager to encourage many enterprises, among which ""the development of iron mines""(4) - Governor Gore had been approached by John Mason for help with his ironworks in Norfolk County (5). Three Americans had applied for permission and support to erect an ironworks on the Gananoque River at the falls to become known as Furnace Falls. They were granted 1000 acres of land in fee simple to encourage their endeavor(6). Sir Peregrine Maitland, only a few months after taking up his duties as Lieutenant Governor in 1818, intended to visit the ""bed of iron ore on the Crow River"" (7) - Maitland was to provide a good deal of support, both moral and substantive, to Charles Hayes when he came to Canada in 1820."

Jan 1, 1999

By J E. Wajon

This paper discusses the background, requirements, need and content of plans for management of drinking water self-supplied to mining-related operations, including construction camps, especially in remote areas of Western Australia. The paper discusses the importance of cooperation between regulators, the mine site operator and the consultant in preparing a plan fully compliant with the Australian Drinking Water Guidelines to protect the quality and safety of drinking water supplied to mine sites. The paper outlines some of the issues that need to be addressed in preparing a drinking water quality management plan, such as hazard identification, risk assessment, the multiple-barrier approach and the concept of critical control points. Data requirements, monitoring, incident management, training and reporting are also covered.CITATION:Wajon, J E, 2013. Drinking water quality management for mining operations in Western Australia, in Proceedings Water in Mining 2013 , pp 321-328 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

By Meng Wang

"In this study, multiple methods that include geological surveying, laboratory studies, and numerical modeling have been used to study the deformation characteristics of a “deep inclined rock roadway with weak planes” (DIRRWP). Failure of the DIRRWP was found to be triggered initially by the shearing of the rock near the weak plane. The movement of the failed rock resulted in reduced confinement of the deeper rocks, and causing the failure of the supporting units and the severe deformation of the surrounding rocks. Hence, it is concluded that DIRRWP stability is affected predominantly by rocks near the weak plane. Corresponding control strategies for DIRRWP deformation were proposed: (1) greater support intensity is necessary to maintain the stability of the whole DIRRWP; (2) additional support is needed for rocks near the weak plane to reduce the potential of failure; (3) to increase the bearing capacity of the floor strata, as the floor needs to be supported; and (4) a supplementary support technique should be considered for cases of large deformation. The case study presented here indicates that the proposed control strategies can significantly reduce the potential of failure in rocks near the weak plane, thus preventing severe deformation of the DIRRWP.INTRODUCTIONAs shallow seams are mined out, the cover depths in most Chinese coalmines have become increasingly greater. Deep cover in a coalmine is considered to occur when the cover depth exceeds 800 m (Sun, Chen, and Miao, 2018). The loading and failure behavior of rocks in a deep cover setting are quite different from those in a shallow cover setting owing to the increase in in-situ stress, temperature, and hyperosmosis (Lobanova, 2008; Zhang et al., 2013). For instance, experience shows that bulking and dilating deformation in deep roadways is much greater than that which occurs in shallow roadways (Hou and Yang, 2018; Zhang et al., 2016). In addition, anisotropic behavior and thickness deviation of coal measure rocks, combined with the appearance of weak planes (e.g., faults, joints, and coal cleats) in coal and/or rocks, can significantly affect the stability of an underground roadway (Ghazvinian et al., 2013; Sun, Chen, and Miao, 2018). The presence of weak planes can significantly complicate displacement and stress transmission in nearby rocks. Additionally, tensile, compressive, and/or shearing failure in rocks near weak planes can be easily caused by high in-situ stresses in deep roadways; such failures may lead to further severe deformation of the surrounding rocks, resulting in roof falls and rib spalling (Kamata and Mashimo 2001; Wu, Ohnishi, and Nishiyama, 2004). A typical failure of the so-called “deep inclined rock roadway with weak planes” (DIRRWP) is shown in Figure 1. Severe deformation can be found near the weak plane. In this study, a plane or thin layer of rock/coal parting that can significantly reduce the strength of the surrounding rocks—and thus affect roadway stability—is defined as the weak plane."

Jan 1, 2019

By Henry Wurtz

HERACLITUS, a sage of antiquity, called the dark philosopher, who refused a throne, preferring a hermit's cell, propounded, twenty-four centuries since, the maxim : [ ] War (or strife) engenders all things. This, though probably intended by Heraclitus to apply especially to the internal forces of nature, is often said, with equal reason, of the affairs of men. Controversial strife, whether fortunately or unfortunately, is a crucible through which all new discoveries in science, and all technical applications of science must pass-a test which they must all endure before they can become so vitalized as to germinate, so to speak, take root in the human mind, grow tip, and overspread the earth. The greater the number and the power of the elements arrayed against such a growth, and of the influences hostile thereto, the greater should be the inherent vitality of the germ, the more strenuous, skilful, and persistent its cultivators and upholders. During the decade last past we have had, in spite of the severe stringency of the times, an active growth of this kind in progress, whose prospective importance it would now be difficult to overrate. This is the movement which has for its motive the idea that, generally speaking, fuel should be gaseous in form, and which has for its goal the introduction into general public use of gaseous products, made by cheap and rapid processes and on a gigantic scale, distributed throughout our cities and towns in distribution-systems which shall be proportionately gigantic, and sold at prices which will bring such fuel within the means of the poorest householders. Personally, for ten years past, the writer has never failed, on occasions public or private, to urge his belief that the realization of this idea, deemed by him a certainty of the future, will bring about

Jan 1, 1880

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By Jerry C. Tien

The rare earth elements (REEs) are a group of 17 chemical (metallic) elements. REEs are used widely in high-technology, clean-energy products as well as weapon systems. China's dominant position as a producer of over 95% of the world REEs output and the world's increasing reliance on REE products have highlighted concerns about the future availability of rare earths in recent years. This paper briefly reviews the REEs world reserves, production, consumption, the impact of our heavy reliance on REEs products and China's changing policies on REE export on world supply chain.

Jan 1, 2013

By D. B. Stewart

In the past few years, much effort has been spent in elucidating the impact of diesel engines on the mine environment. This paper summarizes diesel fundamentals , exhaust emissions and typical tailpipe concentrations. Mine sampling results and an evaluation of exhaust treatment systems are discussed. A review of changes in pollutant concentrations between the tailpipe and the mine exit is made and suggestions are given to reduce operator exposure to diesel contaminants.

Jan 1, 1978

By H. Tveit, E. H. Myrhaug, J. K. Tuset

Silicon metal as a commodity material is produced by carbothermic reduction of quartz in electric submerged arc furnaces, where CO2 forms as a by-product. Since 1997 the Norwegian Ferroalloy Producers Association have been engaged in research programmes aiming for reduced CO2-emissions associated with fossil carbon in their processes. One important issue has been to study how charcoal and wood chips perform compared to coal and coke in the silicon process. The ability of the carbon-rich reduction materials to react with SiO-gas is commonly assumed to be of large importance to the performance of the process. Based on laboratory experiments with different carbon materials, combined with estimation of parameters in a mathematical model of the reaction between carbon and SiO-gas, a foundation for a theoretical study of the performance of the carbon materials in a silicon furnace is established.

Jan 1, 2004