Search Documents

By Irwan Halim, Seung Han Kim

This paper will describe design of precast segmental tunnel lining for the Pawtucket CSO Tunnel Project in Providence, Rhode Island. The tunnel is 11,700 LF long with 30-foot finished diameter to be constructed in complex sedimentary rocks. Special features of the segments include a large keystone and no connector used on radial joints. The typical segments will be steel fiber reinforced, and hybrid segments with additional steel rebars and shear bicones will be used around the adit openings without use of any structural framing. The important design considerations will be discussed, including special 3D segment to adit connection analyses performed.

Dec 1, 2022

By George S. Rice

In 1911 the Director of the United States Bureau of Mines instructed the chief mining engineer of the bureau , during an investigation of coal-mine safety conditions in Europe, to ask the directors of the various mine-experiment stations whether they would favor a European conference . The majority of the officials in immediate charge of experiment stations favored the plan , and Victor Watteyne, inspector general of Belgium, suggested that the United States call such a conference to be held immediately after the Eighth International Congress of Applied Chemistry, which was to assemble in New York on September 3, 1912 . Accordingly, invitations were issued by the United States Government to those countries having mine-experiment stations , namely, Austria-Hungary, Belgium, France, Germany , and Great Britain, and to those that contemplated the establishment of such stations , Canada and Mexico . All but Great Britain and Canada accepted ; Mexico designated a representative , who later found it impossible to come. The Government of Great Britain in declining, expressed regret at its inability to accept ; an informal statement was made that the opening of the experimental gallery at Eskmeals , England , occupied the attention of the officials in charge . Delegates were appointed by their respective Governments as follows: Austria-Hungary, Julian Czaplinski , royal mining engineer. Belgium, Victor Watteyne , inspector general of mines . France, J. Taffanel, director of the Lievin experiment station . Germany, Carl Beyling, bergassessor, director of Dortmund experiment station. United States , Charles E. Munroe, consulting explosives expert and George S. Rice, chief mining engineer of the Bureau of Mines . Subsequently Mr. William O'Connor , a mining engineer and mine operator of Wales , who opportunely appeared at the Pittsburgh station with letters of introduction from the South Wales Institute of Engineers and from prominent mining officials of Great Britain , was unanimously invited to take part in the meeting as an unofficial representative of Great Britain . Messrs . Beyling, Taffanel , and Watteyne were met in New York on September 3, by George S. Rice, who accompanied them to Washington, where they were welcomed by Director J. A. Holmes , of the Bureau of Mines , and where , with the delegates to the Eighth International Congress of Applied Chemistry , they were presented to President Taft . Mr. Taffanel was unfortunately called back to France just before the scheduled time of the conference on account of a mine disaster ; the other delegates , including Mr. Czaplinski , convened at Pittsburgh on the morning of September 14. Mr. Rice, representing the Director of the Bureau of Mines , acted as temporary chairman , and called the meeting to order.

Jan 1, 1914

By G Neely

COPING WITH COMPLEXITY In every industry, and mining is no exception, plant and processes increase in complexity over time and managers and operators need correspondingly more knowledge. The mine manager has to delegate details to operators, engineers, metallurgists, accountants, safety specialists, personnel officers and the rest. Is it reasonable then, to expect the Mines Inspector to be competent to judge the conduct of all these operations against the criterion of the regulations? Obviously not, but what are the alternatives? One is a superficial inspection where the inspector goes on a hazard hunt for broken steps and missing handrails. Another is one in which an army of specialist inspectors marches on a mine, sometimes outnumbering the staff. Each is competent to assess some part of the operation and if he or she can find an opposite number among the mine staff, they can discuss details. But what good does it achieve? The system acts to remedy present defects and to make recommendations which, if only they were followed, would prevent the same things happening again. Given that this process has been going on since the first Factory Act of about 1840, how is it that there are any more defects left to put right? The answer of course is that defects keep appearing, and new defects arise as fast as the old ones are found and corrected. Further progress can only be made by preventing defects at their source.

Jan 1, 1994

By J. Uys, P. J. Mokganya, J. Olwagen, R. C. W. Webber-Youngman

This article discusses the critical role of leadership in the technology adoption process within organizations, particularly in industries like mining, where innovation is essential for maintaining competitiveness and operational efficiency. It highlights the limitations of traditional technology adoption models, such as the Technology Acceptance Model (TAM), Diffusion of Innovations (DOI), and Unified Theory of Acceptance and Use of Technology (UTAUT), which focus on individual factors and overlook the strategic and organizational roles of leadership. The study proposes the Ambidextrous Leadership-Technology Adoption (ALTA) model, which integrates leadership styles such as transformational, transactional, adaptive, and ambidextrous leadership into the technology adoption process. The model emphasizes the balance between exploration (fostering innovation) and exploitation (ensuring operational efficiency). The findings suggest that transformational leadership fosters innovation by encouraging risk-taking and creativity, while transactional leadership ensures efficient technology integration. The article also identifies key barriers to technology adoption, such as organizational resistance to change, which can be mitigated through adaptive leadership that addresses employee concerns. The research emphasizes the importance of a supportive organizational culture and cross-functional collaboration, which are essential for successful technology adoption. The study concludes by offering practical recommendations for leaders to foster a culture of innovation, manage resistance, and balance short-term efficiency with long-term technological advancement.

Nov 27, 2024

By Frances H. Clark

DEVELOPMENTS in powder metallurgy have been disappointing in 1943. If any new part has gone into large-scale production, knowledge of it has been restricted by considerations of national security. Nor have any outstanding papers appeared to advance the theory of the subject during this period.

Jan 1, 1944

The profitability of individual ore blocks can be classed as clearly profitable, clearly not profitable, and those in between which are by nature quite sensitive to their major cost and revenue drivers. It is often the case that the most effort goes into the least profitable ore blocks to ensure that these will in fact not generate a loss. In these cases a cut-off grade policy is often not sufficiently live to separate individual sources given the volatility of financial markets and individual circumstances of some sources particularly in remnant operations such as Mount Isa MinesÆ Lead Mine. Standard sensitivity analysis can determine which factors stope profitability is most sensitive to. However, this does not usually indicate the likelihood of any input change, nor the combined effect of multiple inputs changing. The author attempted to modify the Lead Stream financial model that determines cash margin by inserting probability distribution functions and then using Monte Carlo simulations to determine the probability of any particular ore block making a profit. This effectively demonstrates the combined effect of varying a number of inputs simultaneously to provide a probability of making a profit. The limitations of this analysis lie in the accuracy that individual probability distributions can be specified. Attempts to generate valid functions from first principles have proved difficult for a number of reasons and these are discussed along with some practical alternatives.

Jan 1, 2002

This volume contains a series of papers describing research conducted by the Bureau of Mines to develop or improve equipment and systems that satisfy the communication requirements of miners doing work related to rail, belt-conveyor, trackless, and hoist haulage systems.

Jan 1, 1977

By E. P. Carman

This report is the 20th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations; it is the second4/ to be issued on a calendar-year basis. Previous reports related largely to publications by Bureau authors during the reporting period. This one discusses the publications issued during 1955 and in addition describes briefly the work in progress during the year. Further details on the published work may be found by referring to the publications cited in the footnotes. The Bureau continues to direct its research and technologic work on coal toward safer and more efficient mining, improved preparation, and more effective utilization, with the ultimate twin goals of promoting conservation and insuring that coal will make its maximum contribution to the Nation's industrial capacity. Significant advances toward these goals were made in 1955.

Jan 1, 1957

By Duane A. Smith

Introduction From the days of the Spanish in the eighteenth century, Colorado's San Juan mining district has attracted miners and public interest. The Spanish left behind names - San Juans, La Plata, Animas, legends of lost mines, and the remains of a few scattered mining operations. They came, but did not stay. Again in 1860-61, as a spinoff of the Pike's Peak gold rush, prospectors climbed the mountains and descended into the canyons searching for gold. They found some, not enough to convince them to remain and confront the isolation, often hostile environment and the Utes, who rightfully felt this to be their home. Not until the 1870s did miners come to stay. In their wake little camps grew in the high valleys and squeezed into narrow canyons. Nowhere else in Colorado were there more rugged mountains, a higher average elevation, nor a climate that one old Swede said was "three months of mighty late fall and nine months of winter." The San Juans proved eventually to be a mineral treasure chest. At the moment, however, the prospectors sought gold. Then they discovered silver deposits and the first rush was on. It got started just in time to be completely overcome by the Leadville excitement. At Leadville, investors almost fell over themselves to buy claims and stock in the hopes of becoming another millionaire like Leadville's own Horace Tabor. The San Juaners could only look from the sidelines and speculate how it might have been had fate been kinder. Fate was seldom kind, as these pioneers quickly discovered. From the mid-1870s on, the San Juaners wrestled with some major problems. And the fate of their district rode in the balance. The problems they faced were similar to those of other Colorado districts, compounded by their geographic isolation. Every mining district needed the best transportation system available, experienced investors combined with sound investment, and mineral reserves to develop. The San Juans offered the last in abundance. It was hoped the first two would appear. Railroads - much needed transportation link Nothing was more desired than railroad connections, the penultimate nineteenth century form of transportation. Colorado's own, the Denver & Rio Grande, resolved the issue with its mountain-hugging narrow gauge. As early as the mid-1870s, the D&RG dreamed of tapping this potentially lucrative market in southwestern Colorado. A national economic depression and then the Leadville silver excitement prevented immediate construction. Not until 1879-80 did survey crews start work.

Jan 2, 1988

By E. J. Kloos

One phase of the work of the Bureau of Mines in health and safety is promoting the use of safe, satisfactory, and reliable respiratory-protective devices. To insure that such devices will be available, the Bureau has established schedules of minimum-performance requirements for the approval of self-contained breathing apparatus (1),4/ gas masks (2), supplied-air respirators (hose masks, air-line respirators, and abrasive-blasting helmets, hoods, or masks) (3), dispersoid (dust, fume, and mist) respirators (4), and nonemergency gas respirators (chemical-cartridge respirators) (5). Approval tests of self-contained breathing apparatus are conducted by Health and Safety District B; approval tests of other types of respiratory-protective devices are conducted by the Branch of Health Research. Manufacturers of respiratory-protective devices may submit their equipment to the Bureau of Mines for approval under the requirements of these schedules. If the device, when tested by the Bureau, meets the schedule requirements, a certificate of approval will be granted, which not only states that the equipment has passed the schedule requirements but also gives information about the limitations of the device. If it is found at any time that approved devices do not meet the requirements of the pertinent schedule, the Bureau may rescind approval.

Jan 1, 1959

By G. L. Oldright

In the first paper of this series (R. 1. 4333) on the cooperative work with the Eagle-Pitcher Mining & Smelting Co., changes in the nature of the sinter feed were measured by corresponding changes in the retorting temperatures necessary to distill zinc at the best rates; the firing schedules summarized such changes. In this paper, third of the series, are noted same of the changes in practice that were brought about by the need to treat more fused, glassy, and "hard" sinter, as the operators qualify it. Losses of uncondensed zinc were increased by adding zinc-bearing materials from which? the zinc was readily distillable to hard sinter requiring higher-temperatures for zinc distillation. The rates of zinc distillation were increased by grinding the fuel finer; there were few benefits and loss of dust on grinding the sinter finer, unless the fine ?coal and fine sinter were brought into contact by pelletizing, and the pellets made but little dust.

Jan 1, 1948

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By Wieda Azani, Alexander Tarigan, Willem de Beer

In block caving, the rates and sequencing of undercut production blasting, drawbell blasting, and mucking are the key levers for attempting to manage cave performance. Cave performance encompasses a range of factors, which include growth, shape and the effect of the cave on the abutments, excavations, geological structures and lithology. We compare production data in several panels in the Grasberg DMLZ and GBC block caves with the seismic response in work areas, around geological structures, and in geotechnical domains. These comparisons enable evidence-based conceptualising of the effect of production rates and mining layouts. By also considering the correlation of seismic release rates in different parts of the rock mass, the wider influence of a cave can be gauged through considering possible stress and / or deformation transfer. This concept is not novel, but it is rarely implemented in a routine fashion, principally because production data rarely are easily available. Previously, it has also been used to retrospectively compare seismic hazard between different mines. This paper discusses practical, day-to-day tools to manage seismic response to mining. Therefore, the paper presents a methodology for presenting seismic release and production rates on integrated plots at any time to facilitate quick identification of correlated spatial regions. This methodology explores the production data collection and geolocation at Grasberg, which will be described in some detail.

Apr 26, 2022

By Bunting S. Crocker

This paper reviews the trends in the past two years in autogenous grinding throughout the world. It covers rock grinding in South Africa, Sweden, Canada, the United States, Finland and Germany. To properly orient the discussion on this subject, the paper attempts to define and classify the scope of autogenous comminution. As this is a relatively new subject, there is often considerable confusion regarding the various practices, which sometimes differ widely. By clarifying the types and forms, we hope to help clear up this con-fusion. Autogenous grinding is being carried out, throughout the world, either in mills grinding in water or solution or in dry mills using air classification to remove the finished material. The wet grinding, particularly, can be divided into: (1) (2) (3) Primary autogenous grinding, or "run-of-mine" grinding. Secondary autogenous grinding or semi-autogenous grinding or rock pebble grinding. Combination processes. -This covers plants in which pebbles made in the primary mill are re-moved and used as grinding media for fine grinding in secondary mills.

Jan 1, 1963

By R. L. Soderberg

This paper is one of a series on mining methods and costs being published by the Bureau of Mines. It describes briefly the mining methods employed since the start of operations in 1937, with emphasis on the diamond-drill blast-hole method of ore breaking and slusher-drift method of ore drawing at the Holden mine of the Howe Sound Co., Chelan Division, Holden, Wash. The Holden mine is in the north-central part of the Cascade Range, 11 miles up Railroad Creek from Lake Chelan. The nearest railroad is at Chelan Falls, 40 miles by boat and 4 miles by highway from the mine. All freight comes into the mine and all concentrates are shipped out via Chelan Falls. The altitude of the main haulage level is 3,500 feet. Railroad Creek Valley is covered with a dense growth of fir and spruce, while most of the surrounding mountains are rocky, with sparse timber growth.

Jun 1, 1948

By Erik Westman, BEN WESTON, SETAREH GHAYCHI AFROUZ, KATHRYN DEHN

One of the most difficult challenges in underground mining is to forecast significant seismic events prior to their occurrence in order to support the safety of miners and to minimize damage to the underground operation. Passive seismic tomography is a tool to image the seismic velocity changes in a rockmass, which can potentially reveal the rockmass behavior before and after a significant seismic event. In this paper, the changes in seismic velocity of the rockmass before and after three major seismic events are investigated to determine whether there are identifiable precursory velocity changes associated with the major seismic events. Conventional mechanics imply that the induced stress at the hypocenter would continue increasing until failure, in the form of an induced seismic event, occurs. With passive seismic tomography we can image changes to the seismic wave velocity distribution within a rockmass and hence infer the changes to the induced stress near the hypocenter. This paper evaluates the hypothesis that induced stress at the hypocenter (as inferred by the p-wave velocity) increases until the seismic event occurs. In addition to analyzing p-wave velocity changes near the hypocenter, changes to the p-wave velocity at “zone centers” were also analyzed. These “zone centers” are regions within the rockmass that consistently have a p-wave velocity that is much higher than the average p-wave velocity for the rockmass. It is found that the p-wave velocity did not increase at any of the three hypocenters prior to the seismic event occurring, however the p-wave velocity did increase in the closest “zone center” for two of the three events.

Oct 12, 2020

By Hugh R. Rhys

The question of the desirability of recovering cullet from MSW in order to recycle it into the manufacturing of glass containers remains a controversial one. The main factors appear to be: 1. The position of the Glass Container Manufacturers Institute (GCMI), as the trade association for most container manufacturers, is that post-consumer cullet is a vital source of raw material. Present requirements are for: a) Flint cullet b) Non-flint cullet of known mix proportions c) Mixed unsorted cullet of known mix propertions c) Mixed or non-flint cullet of unknown mix proportions. A market balance for these products exists, and this might somewhat limit the outlets for (b), (c) and (d), or severely limit the outlet for (d) alone. 2. The color specifications are rather strict. With cullet admixtures of 20% of the melt or more, and the use of decolorisers in a flint furnace discouraged because their action is reducing in a process which requires an oxidising environment, color contamination in a flint furnace is serious.. For amber and green furnaces (reducing) it is less serious, but in order that the quantity of decolorisers may be controlled, the color balance (as a measure of the Fe and Cr content) of the admixtured cullet should be known. 3. Why not simply color analyze, either by a continuous on-stream or off-stream: photo-electronic analysis, or by systematic batch sampling (with some kind off electronic surveillance of the mainstream) and just send mixed, color measured cullet to only amber and green furnaces? The flint would-be simply included in the mix. This is probably technically feasible, but is subject to the market limitations noted in point1.

Jan 1, 1975

By V. E. Dawson

Brake testing of large mining trucks was initiated in British. Columbia in 1969 following an accident involving the failure of the service brakes of a l00-ton electric-drive truck. Some selected results of the 1976 brake test program are presented and discussed ?in this paper . The tests were conducted on end- dump trucks having load capacities ranging from 85 to 235 tons. All tests were made with the vehicles fully loaded operating on downhill grades varying from 8 to 10 %. Stopping distances were measured from initial speeds varying between 10 and 39 mph. The results are adequate, in most cases, to determine the "ultimate" capabilities of the service brakes of varying models and sizes of haulage trucks operating in British Columbia mines.

Jan 1, 1977

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By Wang Xuewen, Bao Qingbao, Xie Jiacheng, Yan Zewen

This study puts forward a virtual memory cutting method based on the prediction of AFC shape. The integrated key technologies include the generation of virtual teaching cutting curve, the height adjustment strategy of front and rear drum, cutting height adjustment strategy, the reciprocating cycle of cutting technology and so on. Through the two algorithms, SVM and ELM, the form of the next working cycle can be obtained by rolling prediction using the form information of AFC in the first several circulations. Based on the obtained dynamic fluctuation of the form in the vertical and horizontal working faces, the position and cutting information of the shearer during its operation can be controlled and predicted in advance, the memory cutting template can be adjusted and modified in time. Employing this method, the more stable, accurate and timely memory cutting of the shearer under the uneven coal seam could be realized.

Aug 16, 2021