Search Documents

The U.S. Bureau of Mines evaluated water-jet-assisted longwall shearers in full-scale laboratory tests and underground. Both test programs showed that use of high-pressure water did little to reduce the shearer motor energy required to maintain a given cutting rate. However, three other major benefits were achieved with the use of water-jet-assisted cutting. At a pressure of 1,800 psi, respirable dust levels were reduced about 80 pct compared with the dust levels of the conventional water spray system operating at 340 psi. Operating at higher pressures required for water-jet assist also resulted in an increase in the average size of coal cut, which translates into a decrease in product fines. Finally, although no controlled measurements of bit wear as a function of water pressure were made, mine personnel reported that the shearer bits lasted longer when water-jet-assisted cutting was used.

Jan 1, 1989

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By Hans W. Schreiber

Most geologic and mining engineering consulting firms* began to experience the recession with declining billing levels, number of inquiries, and proposal requests in late 1981 or early 1982. As of today, most of them have been functioning at reduced income levels for nearly a year. And while many consulting firms have apparently reached a stabilized income level, they can see little prospect for attaining normal (pre-late 1981) billing levels and income for the remainder of 1983. A few firms have escaped being affected by the recession. Such com panies almost without exception are small (fewer than 20 personnel), offer a limited range in technical capabilities, and tend to be highly specialized in a particular niche. They include those specializing in the heap leaching of precious metals ores, in ground water testing programs, and in the derivation of computer-aided programs to monitor particular mineral processing functions. Those firms affected by the economic downturn have instituted a variety of policies and undertaken actions to cope with significantly reduced incomes to bring fixed costs in line with the depressed demand for services. These changes fall into the following broad categories: • management and management practices; • markets and market definition; • marketing and the pursuit of assignments; and • administration and personnel relationships. Not all of the perceived changes have necessarily been instituted by every consulting firm, and any one appears sporadically instituted. Management and Management Practices In favorable times the managers, and often the owners of the equity, of consulting firms tend to concentrate their attention on the part of the business they find most satisfying and enjoyable. For some, this means acting as project or assignment leaders, even undertaking a specific technical aspect of the job. For others, it means constant marketing with the associated heavy travel and entertainment schedules. In unfavorable conditions, such as the current recession, managers tend to spread themselves far more thinly, expending time and effort on all facets of the business including marketing, proposal preparation and cost estimating, budgeting, general administration, accounting and cash flow monitoring, project/assignment overview, and actual client work. The manager who in favorable times concentrated on client work is now less billable. The manager who concentrated on marketing is somewhat more billable. The manager now needs to pay attention to and expend equal effort on each facet of the business just to keep all the facets in relative balance. Falling behind schedule on a client job or carrying an unduly large percentage of accounts receivable exact a cost to the firm. Clearly the absolute cost to the firm is the same whether demand for service is good or slack. But in periods of slack demand the firm is frequently less able or even unable to bear such costs. Marketing and Market Definition Markets appear to have undergone some significant changes: • Federal and state governments have assumed a greater importance as providers of work vis-a-vis both industry and private groups. • Projects with increase-in-capacity aspects have given way to projects with maintenance or reduced operating cost aspects. • Projects searching for new deposits of minerals in generally new locations have given way to projects reviewing known mineral districts or known deposits. • Industrial mineral and mining companies have exhibited a great propensity to cut back the use of consultants and to undertake as much work as possible in-house. Further-more, a number of industrial mineral and mining companies have entered the competitive arena with consulting firms, submitting proposals (usually to the federal government) in an effort to keep their staffs intact and occupied. In response, consulting firms have reevaluated their capabilities by reviewing old work and reassessing personnel. The purpose is to broaden the services offered and the potential client base, thus redefining the available market. For example, a firm specializing in assessment of technical and cost parameters of a deposit would normally assist a prospective lender in judging the deposit's suitability for project financing. That same company could easily expand into the field of analyzing production costs for an individual operation -something that is needed in periods when lower prices reduce profit margins. Similarly, a firm that has confined such economic assistance to commercial banks could expand to provide its expertise to other lending and even equity buying in-stitutions such as insurance companies. Marketing and the Pursuit of Assignments With few exceptions, consulting firms have significantly increased their

Jan 2, 1983

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By David A. Monaghan

This report describes the results of a 2-year investigation of extensible face ventilation techniques and systems for use at the working face in underground coal mines. The goal was to provide a safe and convenient method of maintaining the extensible system within 10 feet of the face, thereby ensuring good ventilation. A summary of approximately 20 extensible ventilation systems proposed or tried in the past is included for reference, together with a detailed description of the design, construction, and underground testing of a new extensible brattice panel and a new fiberglass duct system. The extensible brattice system utilized a special panel which could be pushed forward as the miner advanced. Brief testing in three mines revealed some conflict with the mining cycle and led to recommendations for two improved designs. The extensible duct system was designed for a Goodman borer and utilized a telescoping tube on the left side of the roof, so that it could be extended without interfering with the miner operator. For mine sections with right-hand return ventilation, a special flat tube section is used to cross over the entry. Underground testing showed substantial improvement in face ventilation without interfering with production.

Jan 1, 1976

By Joan K. Kuenzi

This Information Circular brings together for consideration recommendations from U.S. Bureau of Mines research in the area of surface mine mobile equipment maintenance for the period 1982 through 1991. It updates the 1982 contract report by Baker and Alves that formed the basis for much of the work described in the present report. Recommendations for hazard abatement during work on mobile one equipment are presented and stem from the results and recommendations of the research in two areas: (1) equipment and workplace hazard reduction, and (2) management of maintenance information. Recommendations included in this report apply to both the operators and maintainers of mobile mining equipment as well as to the manufacturers of that equipment.

Jan 1, 1995

By E. E. Donath, L. L. Hirst, L. C. Skinner

Two processes are available for the production of synthetic fuels from coal high-pressure hydrogenation and the carbon monoxide-hydrogen synthe- sis. This paper presents some ideas and new developments in coal hydrogen- ation that have been incorporated in an estimate for the production of 30,000 barrels per day of liquid fuels, mainly gasoline. A few comparisons of the processes will be helpful before discussion of the details of pro- posed improvements in the hydrogenation process. The principle of the high-pressure hydrogenation process ie the addi- tion of hydrogen at pressurea in the range of 3,000 to 10,000 p.s.i. to coal at elevated temperature and with the help of catalysts. On the other hand, the principle in the Fischer-Tropsch synthesis is the complete break-down of coal into a mixture of carbon monoxide and hydrogen, followed by the catalytic combination of these two gasse into hydrocarbons or suitable catalysts. For the synthesis, moderately elevated pressures of about 350 p.8.1. will bo used in the immediate future, although it can be carried on at atmosphoric pressure with certain catalysts. The products of these two processes using coal as raw material are almost as differont as hydrocarbons can be. The products of the high-pres- sure hydrogenation of coal reflect the original constitution of the coal. They are, therefore, rich in ring compounds, both aromatic and naphthenic, but, due to the action of highly comprcesed hydrogen and catalyst, are satu- rated and very stable. These constituents give the gasoline a high octane number and excellent rich-mixture performance, combined with good gum and storage stability. Therefore, this gasoline is suitable for aviation gaso- line or base stock. The Diesel fuel can be hydrogenated to a centane number of 45 or higher, which is entirely satisfactory for operating normal Diesel

Dec 1, 1948

By H. B. Merlin

"The past demands for energy and the contributions by the major sources are shown for the world and regions, and for Canada. Three forecasts of future demand are presented. By the year 2000, the world will be consuming energy at a rate of 670-700 x 1015 Btu/year. Canada's rate is estimated at 20 x 1015 Btu/year. Electricity will increase its portion of energy from 7.5 per cent to 15 per cent, and more than 40 per cent of the primary energy w1ll. be required to generate 1t. World, regional and Canad1an forecasts are g1ven for total electricity generated and for electricity generated in nuclear stations. The integral world requirement for energy by the year 2000 will be over 12 x 10 18 Btu. Current recoverable fossil and hydro reserves are about 18 x 1018 Btu. The total reserves are estimated to be seven times greater.World production of electricity in nuclear stations by the year 2000 will be almost three times the electricity produced in the world today. The amount of fuel consumed in generating this electricity will depend upon the types and mix of reactors installed. The heavy water reactors, alone or in conjunction with fast breeders and liquid fuel reactors, are the most efficient users of uranium and thorium resources. The heavy water reactors are also the most efficient producers of plutonium which will be required as fuel for fast breeders."

Jan 1, 1969

By David Brown, Dirk van Dyk

Horizontal rotating mills are being used all over the world associated with different mineral and power generation industries. David Brown South Africa, with over 140 years of experience in gear manufacture and design, has been supplying these industries with innovative designs at exceptional quality. The gearing systems associated with these industries are challenged daily with operating conditions with are not always fully understood. Failures are therefore experienced, over time in the industry, which can therefore not always be fully explained. David Brown South Africa has developed a gear monitoring system, the Intelligent Gearing System, in association with Transmission Dynamics (UK), in order to monitor and analyze these operating conditions in real time. The system has been designed on the principles of Six Sigma, incorporating Design for Six Sigma. The purpose with this system design is to monitor the operating conditions on the pinion, record the information and analyze the data in relation to the rate of fatigue damage to the girth gear and pinion. This is done in real time and unattended. The output from the Intelligent Gearing System can be fed back into the operating system of the mill user, in order to display an alarm for operating conditions exceeding the design criteria as well as information on the rate of fatigue damage due to these operating conditions. When the mill operating conditions are better understood, and the effect on the fatigue life of the mill gearing components, mill users can forecast critical spare holding levels with an increased accuracy. The Intelligent Gearing System also allows early actions to remove reasons for system overloads.

Jan 1, 2007

By Laurence G. Britton

Accurate flammability and ignitability data for chemicals form the cornerstone of procedures used to assess the hazards associated with commercial chemical production and use. Since 1967 the ASTM E27 Committee on the Hazard Potential of Chemicals has issued numerous, widely used consensus standards dealing with diverse testing and predictive procedures used to obtain relevant chemical hazard properties. The decision to issue a standard rests solely with the membership, which consists of representatives from industry, testing laboratories, consulting firms, government, academia, and instrument suppliers. Consequently, the procedures are automatically relevant, timely, and widely applicable. The purpose of this paper is to highlight some of the widely used standards, complemented with hypothetical but relevant examples describing the testing strategy, interpretation, and application of the results. A further goal of this paper is to encourage participation in the consensus standards development process. The paper is published in two parts. The first part (in the preceding issue of Process Safety Progress) dealt with the E27 standards pertaining to thermodynamics, thermal stability, and chemical compatibility. The second part, published here, focuses on the flammability, ignitability, and explosibility of fuel and air mixtures. © 2005 American Institute of Chemical Engineers Process Saf Prog 24: 12?28, 2005

Jan 1, 2005

By W. R. Hardwick

This paper describes mining methods and practices of the Morenci Branch, Phelps Dodge Corp., Greenlee County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts in the United States. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed substantially to improving the efficiency of mining operations. The morenci open-pit mine (see photograph, fig. 1) is in southeastern [zona] (fig. 2), on U.S. Highway 666 about 5 miles north of Clifton, county at of Greenlee County. The concentrator and smelter are near the mine at an altitude of about 4,400 feet. Figure 3 is a map of the mine and plant.

Jan 1, 1959

By L. Simpson

South African is a repository of significant deposits of a variety of minerals. The Citigroup confirms this assertion with an estimate of in-situ valuation of US$2.5 Trillion. The mining sector plays an important role in the South African economy. In addition to the mineral resource base South Africa has other comparative advantages. Firstly, South Africa retains major mining companies that participate globally, including Anglo American, Goldfields and De Beers. Their global involvement offers much to the local mining sector and the broader economy. Secondly, government established research councils. The Council for Geoscience (CGS) was established to manage the Geological Survey of South Africa, including the reduction of geo-scientific investment risk. The Council for Scientific and Industrial Research (CSIR) promotes industrial development, including mining technology development. Mintek undertakes mineral research from mineral examination of ores, to extraction and refining technologies and manufacture of end products. Thirdly, South African universities teach and conduct research along the mineral value chain. They have increased their minerals graduates? capacity, thus advancing knowledge and skills. Knowledge and technical progress are behind productivity growth and emergence of competitive advantage. The research and development (R&D) capabilities of industry, science councils and universities, working in unison, will enhance the competitiveness of the South African mining industry. The National System of Innovation (NSI) requires multi-disciplinary, collaborative research. Key R&D elements, including skills and expertise, funding and facilities, must be available to implement a long-term national strategy or programme. Improved international collaboration and partnerships between government, academia and industry driven human resource development (HRD), ultimately develop the critical mass for inter-generational skills requirements. This trend requires an expansion of research collaboration programmes. Decisions involving investments and collaborative actions pertaining to R&D in the sector necessitate an analysis of the South African mineral value chain R&D capability. This paper analyses the evolution of R&D capability from exploration to refining, tertiary education, science councils and industry. The political economy of the evolution of this capability is analyzed in relation to the central role that the South African government plays in creating an appropriate supporting environment and related initiatives to enhance R&D and innovation. Keywords: research and development (R&D), science councils, universities, industry, innovation policy, South Africa

Sep 1, 2012

By Aimee A. Woolsey

Enterprise Unmanned Traffic Management is a holistic system concept evolving from technological developments in radio frequency where dynamic tracking can be added into current and emerging platforms. This is done through inexpensive RF sensors capable of real-time and cooperative, non-GPS tracking enabling digital visualization of assets, including unmanned aerial systems (UAS). The RF sensors are low size, weight, and power (SWaP), creating efficiencies in energy and material consumption while transmitting positions in real-time and at long ranges. Multiple UAS and other unmanned vehicles can be visualized for risk mitigation in operations,

Oct 17, 2022

By J. E. Fraley

This report describes the preliminary results of a Bureau program to develop and test an inexpensive grout for full-column support of roof bolts. Various inorganic grouts were tested in both cartridge and slurry form. Tests were also performed on methods of water packaging and on the effect of fillers on the grout strength. Results showed that some grouts had poor early strength and exceptional mid-to long-term strength. Laboratory tests have shown that rapid-setting inorganic grout could be an economical replacement for resin bolts if the short-term strength could be increased. Further development to improve its early strength would need to be tested in the laboratory and underground to prove its potential for the mining industry.

Jan 1, 1987

By Steve Kral

The domestic mining industry may be in the doldrums but there appears to be hope, at least from a regulatory standpoint. At least one US senator believes that the events of Sept. 11, 2001 made many citizens see the need for the country to become more self-reliant on its growing energy needs. Even before that tragic day, however, the Bush administration was making a strong push to open up more public land for energy and natural resource development.

Jan 1, 2002

By H. A. Oaks

FROM 1921 to 1939, the aeroplane played an increasingly important role in Canadian prospecting and mine development. This service has been interrupted by the war, but undoubtedly it will be accelerated in the postwar years, if suitable aircraft are available. The purpose of this paper will be to review the uses to which the aeroplane has been put in prospecting and development in the past, and its future possibilities as an aid in prospecting. If by review, and deduction, we get a clear picture of what we expect the prospecting plane to do, we may be able to arrive at a very close approximation of its required characteristics and, from this, an idea of costs. 'Function' is defined as the mode of action by which it (the aeroplane) fulfills its purpose. We will endeavour, therefore, first to find what this purpose is, or should be, so that our expectations will not be too limited nor too great-and then find, by analysis, what performance we require in an aeroplane to meet our reasonable expectations at an economic price.

Jan 1, 1945

By Geoffrey C. Huggins

Diagnostic: tests were performed on a production ST-5A Load-Haul-Dump machine manufactured by Wagner Mining Machinery Company to evaluate and rank order noise sources. The diagnostic evaluation indicated that the major noise sources were the transmission, the engine, and the cooling fan. This phase was followed by implementation of recommended noise control treatments, which included vibration isolation of the transmission, a transmission enclosure, an engine enclosure, and modifications of the inlet to the cooling fan. The final step in the program was an underground operational period which began on 31 August 1976 at the National Gypsum Mine in Shoals, Indiana. The noise control treatments successfully reduced the LHD operator noise exposure by 7 dB(A), thus increasing its allowable operation time by a factor of 2.7. Actual measurements made underground using noise dosimeters have indicated that, during, a typical shift, the noise control treatments have reduced the fractional exposure to an allowable level. The report discusses the mechanical aspects of the LHD, its noise sources, the treatments applied, the final levels achieved, and field experience with the noise-controlled machine.

Jan 1, 1977

By W. G. Pariseau

Reliable stress measurement using hollow inclusion gauges and monitoring stress change using borehole stress meters and borehole deformation gauges in anisotropic rock remains a challenge for the rock mechanics community. In this regard, the complex variable method advanced in 1983 for deducing stress in anisotropic rock is flawed and software is privileged. Fortunately, advances in computer hardware and software now enable fast, reliable reduction of hollow inclusion stress measurement data for determining stress in anisotropic rock. Monitoring stress change in anisotropic rock poses a different challenge but is also subject to numerical analysis. Stress measurement using a hollow inclusion (HI) gauge such as the triaxial Australian HI is done in four steps: 1) drilling a measurement hole, 2) installation of an HI, 3) stress relief of the HI by overcoring, and 4) data reduction. The last step, data reduction, is the focus of this work. The process is well-known in linearly elastic, isotropic rock (Worotniki and Walton 1976, Duncan Fama and Pender 1980). However, in case of linearly elastic, anisotropic rock the requisite technology is not readily available. This situation is somewhat surprising because anisotropy is more often the rule rather than the exception, especially in the neighborhood of ore bodies. Rahn (1984) has pointed out the potential for significant errors with neglect of anisotropy and the adverse consequences for engineering design. Amadei (1984) has also pointed out the potential for errors with neglect of anisotropic rock properties in stress measurement. Worotniki (1993) cites other studies that indicate potential for serious errors when doing measurements in anisotropic rock. In both theoretical cases (isotropy and anisotropy), data reduction is essentially a composite of solutions to boundary value problems in linear elasticity. In the finite element approach, the analysis is a simulation of gauge hole drilling, installation and overcoring. Two important advantages with the finite element approach are a more faithful representation of the conditions of HI stress measurement than approximated in theory and the capability for handling rock whether isotropic, transversely isotropic or fully anisotropic

Mar 2, 2022

By Larry M. Southwick

There have recently been executives at major metals companies who have recommended that Greenfield Projects not be pursued. Greenfield includes not only new geographical locations, but also new technologies and new types of feed materials. In the middle part of the 20th Century, two such projects were successfully commercialized to recover nickel from Cuban lateritic ores. One project (at Nicaro) used the Caron ammonia-ammonium carbonate leach and the other (at Moa Bay) a high pressure acid leach. How both of these projects dealt with these Greenfield issues will be reviewed, based on the original reports that described the research and development of the plants. This study will include a review of the critical ore characterization and sorting issues, as well as the extractive metallurgical, product recovery and equipment selection and sizing problems and how they were solved at each stage of project development, from laboratory through one or more pilot scale plants to start up and operation. In one case, a major revision of the plant was made after several years of operation to correct operating, equipment selection and materials of construction problems that hindered economical operation. These descriptions will provide a guide through the complicated and critical issues that in recent times have caused many companies to give up on similar development. Even with the more advanced analytical and computational tools available to today’s mineralogists, engineers and metallurgists, the basic concepts with which these projects successfully addressed their sets of problems are still required. In addition, upper management, now perhaps further removed from hands-on experience than was common then, will see how complicated problems require intense and detailed effort to avoid failure in the field and capital blowouts. Build it and we will make it run, kicking the can down the road and borrowing operating and design concepts incorrectly on technological issues, or nine year olds on a sugar high making financial decisions are not philosophies by which to succeed with Greenfield Projects.

Jan 1, 2014

By David Davison

Metafex®* is an inert material that is more energetic than explosives when activated. Because Metafex is inert until activated (a moment before use), it can profoundly change the logistics of systems and processes that require energetic materials. We have obtained positive test results for a Metafex configuration (called a flat pack) that operates at the practical voltage of ~20 kV. We describe the outcome of the testing and potential uses of the material.

Jan 1, 2006