Search Documents

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude run to stills. Furthermore, the premise the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

By C. A. Pickles, J. M. Toguri

The refining of two molten Ag-Cu alloys, containing 7.5 and 11.2 mass% Cu, with a borosilicate slag was investigated using both air and pure O2 to determine the effects of the following variables: flow rate of oxidising gas; injection time; mass of sodium borosilicate flux; and injection of the oxidising gas into either the slag or the metal. The results demonstrate that more than 90% of the Cu can be removed with Ag losses of less than 5% and that refined metal with a Cu content of less than 0.5 mass% can be produced. Ag losses to the slag increased with the amount of Cu removed, and a mechanism is proposed to account for this

Dec 1, 1995

By Masami Hayashi

The Bureau of Mines estimated the cost for ,3 uranium ion-exchange recovery system using five grades of 17.0, leach solution producing 815,570 pounds of U 0? per year from an ammonium bicarbonate in situ leach solution. The system flowsheet consisted of four unit operations: (1) Multiple-compartment ion-exchange (MCIX) absorption; (2) MCIX elution; (3) precipitation of the uranium as yellow cake, filtering, calcining, and packaging; and (4) waste disposal. The total fixed capital cost of a system treating 2,000 gallons per minute of 0.1-gram-per-liter-U308 leach solution was estimated as $6,888,000. For n basic case of an MCIX system depreciating in 9 years, unit production cost of U308 was $3.51 per pound. A decrease in feed solution grade from 0.[4] to 0.03 gram per liter increased the production cost exponentially. Shorter depreciating periods significantly increased the production cost particularly for the lower grade feed solutions.

Jan 1, 1979

By R. B. Booth, W. F. Linke

The continuous interest of the American Cyanamid Company in producing superior polymeric flocculants and dispersants for the mining industry has resulted in a broad, general study of the physical chemistry of mineral-polymer systems. The aim of this program has been to establish a sound theoretical basis on which practical problems could be analyzed, and which would lead to the development of new and improved flocculating and dispersing agents. This study has required the cooperative effort of physical, analytical, and polymer chemists, as well as engineers familiar with mining problems. This report summarizes the results of some of our investigations over the past two years. Further studies along these and other lines are in progress and will be reported in the near future. MEASURING FLOCCULATION IN THE LABORATORY The foremost problem in studying flocculation in the laboratory has been to establish reproducible methods of comparing and evaluating the effectiveness of various reagents. Previous workers have measured settling -rates 1,8 filtration rates2 , and sediment volumes3 . Direct observations of the floc size, or the clarity of the supernatant liquid, can also be used. AIthough these parameters are all interrelated, they do not always measure the same physical properties of the suspensions, and hence are not equally useful or reliable. Whatever the method of comparison selected. the testing procedure must be carefully defined and standardized. The results must be satisfactorily reproducible, and for practical purposes must accurately reflect the results obtained in mill use. In order to compare the data obtained in these various types of test, the physical nature of the flocculated system must be examined in some detail. In an unflocculated system, only the larger or denser particles (the "sands") settle at a useful rate. The sediment can be observed to build up from the bottom of the cylinder, while the fines remain in suspension for a long period of time. If the system is not disturbed, even the microscopic fines can be seen to classify themselves as they fall over a period of days. When a high molecular weight polymer is added to the system, the colloidal particles are tied together randomly in flocs, and the sands and fines settle together. The line of demarkation between solid and liquid phases moves downward from the top of the cylinder. The settling rate of the flocs depends on their size and on their effective density. For a given mineral sample, the larger the flocs, the faster the settling. Since the large flocs cannot pack as closely as small ones, they produce a sediment with more pore spaces, and hence of larger volume, which is easier to pump and to agitate. Although it is nearly impossible to measure individual floc sizes, it is relatively easy to determine settling rates and sediment volumes. Of these two, the settling rate is simpIer to measure, and hence generally more practical. Reproducible sediment volumes can only be obtained by allowing the solids to pack for a rather long period of time (e.g., hours to days), and although the volumes thus observed are directly related to the degree of flocculation (average floc size), it is often impractical to wait so long for the results.

Jan 1, 1961

By A. Azizi, P. Blatter, A. Bouajila

"Due to the high reactivity of sulfide minerals in alkaline cyanide solutions, some parasitic reactions inflict a heavy gold surface passivation and excess cyanide consumption resulting in a dramatic decrease of the gold leaching rate. Atmospheric pre-oxidation was shown to be an effective tool to enhance gold extraction by preventing a passive film from forming on the surface of gold grains. This work aims to highlight efforts undertaken to determine: (1) how gold cyanidation is limited by passivation; (2) what are the reactions and mechanisms involved during gold cyanidation; and (3) how a better understanding of fundamental issues can be used to design a proper pre-oxidation strategy. INTRODUCTION Precious metals (PM), gold in particular, naturally occur in contact within a wide range of sulfide mineral systems. Hence, one of today’s most challenging R&D tasks consists in accounting for the presence of sulfides on the cyanidation behavior of gold. An important body of knowledge reveals that metal sulfides display a range of reactivities in alkaline cyanide solutions (Marsden & House, 2006). Such reactivities are acknowledged to inflict additional utility costs and loss of profits because they are accompanied with higher consumption of cyanide and/or formation of undesirable by-products that are often detrimental to gold leaching rates. Gold recovery in cyanidation is hampered by a multitude of factors, among others: (1) consumption of excess cyanide as a result of the formation of thiocyanate and dissolution of transition (Cu, Fe, Zn, etc.) metals (Habashi, 1967); (2) gold surface passivation by solid reaction products, e.g., Fe(OH)3 (Guo, Deschenes, Pratt, Fulton & Lastra, 2005), sulfur (Dai & Jeffrey, 2006; Jeffrey & Breuer, 2000;) or oxo and thiooxo (SbO33- SbS33-) salts in alkaline solutions (Guo et al., 2005). Because of their energy structure, most of the sulfide minerals exhibit semiconductor properties (Marsden & House, 2006). Therefore, the contact between constitutive sulfide minerals inside complex sulfurous ores entrains electrochemical phenomena in which sulfide dissolution is a genuine corrosion process (Azizi, Petre, Olsen & Larachi, 2010). For instance, galvanic interactions could be initiated between the various constituents within the ore and could substantially increase or decrease the reactivity of some of the associated minerals."

Jan 1, 2012

By K. H. Brandt

A standard planning system for the development of roadways was adopted for German coal mines based on the results of geotechnical and rockmechanical investigations. Its goal is to provide for sufficient support systems under conditions of multiple seam mining at great depth. The report points out the required determination of geotechnical parameters and the basis for achieving a high level of planning reliability and resulting high performance in roadway development and longwall mining. The instrumentation and the planning procedure for selecting the support design most appropriate for the geotechnical conditions are described and demonstrated by examples.

Jan 1, 2004

By J E. Askew

The rapid expansion of gold production in Australia over the last five years can be attributed in part to the development of selective mining techniques for open pit gold operations. These techniques allow an increase in head grade with a substantial reduction in mill feed tonnage, as compared with traditional open pit designs. As a result, the capital requirements for mine development and mill construction are substantially reduced, improving the cash flow profile in the early years of operations. To put such a design into effect, the emphasis of mine production must be on producing gold, rather than tonnes of ore. Mine planning at Martha Hill has been based on such a philosophy. After the quantity and grade of the resource had been defined, the exploration programme was increasingly concerned with the local variability of ore zones, and with determining the position of values within broad ore-definition envelopes. The purpose of this work has been to allow the prediction of the tonnages and grades achievable from various levels of the pit when mining selectively using hydraulic excavators. The studies have so far indicated that the Martha Hill deposit can be mined selectively during the early years of production. The additional costs for detailed grade control and a reduced digging efficiency are more than compensated by the exclusion from the mill feed of much valueless material.

Jan 1, 1986

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

An examination is made of some of the consequences of a magmatic gas phase developed during a late stage of differentiation of an acidic magma. Elements possessing halides with high partial pressures (Sn, Mo, W) may be removed from the magma by distillation into gas bubbles in the manner suggested by Fenner (1933). The common chalcophile elements are not affected by this mechanism, but form sulphides which may become attached to rising gas bubbles by one of three distinct mechanisms. The gas bubbles may then carry the sulphides upwards and concentrate them in some favourable locus, giving rise to an ore-forming fluid. The process would operate selectively upon different sulphides and is capable of providing an explanation of the paragenetic succession observed in ore deposits as well as other important geological criteria of ore genesis.INTRODUCTIONThere is a widespread belief among contemporary geologists that a large and important class of ore deposits is genetically related in some way·to acidic igneous rocks. This class includes the tin-tungsten-molybdenum-bismuth type of mineralization as well as a variety of sulphide deposits.A basic problem confronting explanation of the genesis of these deposits is the manner in which trace elements which were originally widely dispersed in granitic magmas were segregated therefrom and concentrated into economic mineral deposits.The principles underlying the formation of one group of minerals deposits (pegmatites) related to granitic magmas ate reasonably well understood, largely due to the labours of Goldschmidt and his school. However, many geologists have noted that there appears to be some sort of fundamental discontinuity between pegmatite formation and the origin of the more common hypogene ores, particularly sulphides.Accordingly it has been suggested that these ores...

Jan 1, 1956

By G. R. Hopkins

The average heat requirement per barrel of crude processed in the United states rose from 555,000 B. t. u. in 1939 to 579,000 B. t. u. in 1940, although crude runs increased from 1,237,840,000 barrels to 1,294,162,000 barrels in that period. Thus the almost invariable rule that the average amount of heat needed to refine a barrel of crude oil declines when total crude runs to stills increases was broken. (See fig. 1.) The reasons underlying the apparent loss in fuel efficiency in 1940 are quite obscure. There is little question but that the principle of heat exchange, the most important fuel saver, was used as extensively in 1940, as in 1939. A few companies replaced purchased power with electricity made at their plants, but for the country as a whole purchased electricity increased 7 percent, as compared with a 5-percent gain in crude runs to stills. Furthermore, the premise -the more complex the products the more fuel required -does not hold, as the yield of ?complex" products, including gasoline, declined in 1940.

Jan 1, 1942

Results of the study of chloride ion concentration effect to osmium-187 sorption from wastewater of copper smelter with use of foreign anionites of different basicity and structure are presented in the work. It was found that the increase of chloride ion concentration in the wastewater helps to increase recovery of osmium using anionites regardless of their nature. The ways to intensify the process are proposed. The method for osmium elution from the anionites with potassium iodate solution was developed. It was shown that the method lets to recover up to 99% of osmium from the anionites. Recommendations for selection of eluents for better recovery of osmium from the anionites were elaborated. Keywords: wastewater, osmium, anionite, sorption, chloride ions, eluent, recovery

Sep 1, 2012

By G. E. Christidis, P. W. Scott

The deposits were formed from low-temperature alteration of pyroclastic rocks. Properties investigated include their cation exchange capacity, swelling capacity, pH, rheological properties, the green and dry compressive strengths, shatter index, wet tensile strength, compactability and permeability. It was found that deposits with abundant opal-CT have poor physical properties. The rheological and swelling properties were found to be influenced by the bentonite grade (smectite content) and the degree of disaggregation of the smectite quasi-crystals. The only deposits of high grade which had good foundry properties were those with no opal-CT. Hydrothermal alteration was detrimental to the physical and chemical properties of bentonites in that it decreased the smectite content and the pH and changed the smectite layer charge and the lattice dimensions

Jun 18, 1905

By D. C. Fleck

Electrorefining yttrium from selected low-melting yttrium--base alloys is investigated, and various halide systems are studied as potential electrolytes for use in preparing low-oxygen yttrium by electrorefining unalloyed yttrium. Yttrium cathode products having significantly less metallic impurities than the anode materials were prepared from alloys containing nickel, iron, and manganese by electrorefining in LiCl-YC13 electrolytes at 900° to 1,000° C. Yttrium-copper and yttrium-magnesium alloys are not suitable as anode feed materials, An evaluation of chloride, fluoride, bromide, and mixed chloride-fluoride electrolytes showed that cathode products containing much less oxygen than the anode material can be obtained in the fluoride and mixed chloride-fluoride systems. Initial cathode current density has no apparent effect on the purity of the products obtained in both phases of the investigation.

Jan 1, 1973

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By Vasilis Androulakis, Caroline Gerwig, Zach Agioutantis

Mining operations that involve caving of the overlying strata are designed so that caving occurs in a controlled manner by progressive overburden failure. However, there are many cases where the overlying strata bridge over the caved area for longer periods than anticipated and desired. As the caved area expands with the advance of the mining panel, excessive amounts of energy accumulate in the roof strata which will be rapidly released when the overburden eventually fails.

By Ruddle R. W.

Solid mattes are generally held to be either (a) eutectiferous mixtures of the component sulphides Cu2S and FeS or (b) mixtures of complex sulphides. This chapter shows that liquid mattes consist essentially of a homogeneous phase in which iron, copper and sulphur are present. The amount of sulphur is generally less than that required to account for all the metals as stoichiometric sulphides; mattes cannot therefore be regarded as mixtures of FeS and Cu2S. Some iron oxide may be dissolved in the sulphide phase and magnetite is often present as a second phase. If the sulphur content of the matte is reduced the composition enters the miscibility gap in the ternary system and either an iron- or copper-rich solution (depending upon the composition of the matte) separates as a new phase. On solidification any one of four phases (iron, copper, Cu2S and FeS solid solutions) may crystallize as primaries. The remainder of the matte solidifies as a ternary eutectic. It is possible that iron oxides enter into this eutectic. Knowledge of the ternary Cu-Fe-S system is far from complete and nothing is known of the quaternary system Cu-Fe-S-O

Jan 1, 1953

By Roy A. Bell

A 200-foot diameter, 72-foot high petroleum storage tank was built in a hillside ravine where a portion of the site contained soft clay fill. Soil-cement piles, 40 inches in diameter and up to 38 feet long, were installed to support the tank shell and ringwall, and a portion of the tank floor by drilling into the stiff to hard underlying soils and weathered bedrock. The goal was to provide a strong enough foundation to resist the seismic tank shell loading and to minimize differential settlement of the tank shell to avoid out-of-round clearance problems between the shell and floating-roof. A cantilevered retaining wall up to 8 feet high was constructed around a portion of the tank perimeter by inserting steel H-beams into soil-cement piles. The cantilever soldier piles for the retaining wall were installed from a temporary earth embankment on the hillside directly over the top of the wall. The temporary embankment was then removed and the tank pad was cut to grade in front of the soldier piles. Some of the soil-cement piles for both the tank foundation and retaining wall could not be advanced to design depth because the drill/mixing tools could not penetrate to the required depth in the hard soils/bedrock. Smaller diameter borings (22 inches in diameter) were drilled through the centers of the short-of-design soil-cement piles to the design depth and then backfilled with concrete.

Jan 1, 1997

By D. Mkhwanazi

The purpose of the project was to optimize load haul dump (LHD) machinery use as they were spending too much time doing what they should not be doing. During the investigation, the author found that the machine's actual availability was 86% and the utilization ranged between 30% and 42%. This shows that the availability of the machine has met its target. Therefore the main problem was with the LHD utilization and that is what the project focuses on. To satisfy the objectives, the author firstly studied the existing mining data like the key performance indicators (KPIs) in order to analyse the machine's availability and utilization; this is what gave direction to the problem. Secondly the author did a literature review on mines with similar problems. This gave the author ideas on what to look at in approaching such a situation. Thirdly, the author gathered information on what the LHDs are doing on a daily basis by doing a time study. This gave the author an idea of how long it took the LHDs to complete a specific task. The author also interviewed operators and their supervisors in order to find the best practice work. This helped in identifying the problem areas when comparing the best practice work with what the LHDs are actually doing. According to the project results, it was found that the LHDs are underutilized due to shortage of drivers and the long distances the LHDs have to travel for material loading and refuelling. The author recommended that the machine utilization should be improved by training more operators in order to eliminate the 'no operator' downtime; the cost arrangement of this recommendation is included in the report. The author also recommended that the travelling time should be reduced by using tractors instead of LHDs when long distances need to be travelled for material loading. Another recommendation for reducing travelling time was to bring the mobile fuel tank closer to a section; the cost arrangement for this recommendation is also included in the report. Keywords Optimizing, LHD utilization, LHD availability, key performance indicators (KPI), shortage of drivers, long distances, mobile fuel tanks.

Jan 1, 2011

By A. T. Yu

The energy crisis and the resurgence of mining activities highlighted 1972-73. Added to the impetus for more effective materials handling systems has been the continued upward trend of inflation and labor costs. The need for addressing the fundamentals has led to the trend toward an overall systems approach to materials handling problems.1 The decision to move forward with large mining ventures such as the $150 million Hibbing taconite comple2 and the immense Carajas iron project must base themselves on indepth studies of a host of factors viewed in the context of an integral mine-transport-market system. What's important is that each ton of pellet or ore must be an economical commodity at the end users' furnace. The project can still be viaable even if certain components in the entire network appear to be individually costly.

Jan 2, 1974