Search Documents

By J. S. Miller

The Bureau of Mines conducted surface tests to determine the feasibility of using liquid explosives for underground rock fracturing. The effects of configuration, confinement, length, critical layer thickness, and fracture-propping sand on detonation and explosive propagation velocity of desensitized nitroglycerin were studied, using polymethyl methacrylate and glass-plate reservoirs through lengths from 3 to 12 ft, with explosive-layer thicknesses from 0.1875 to 0.0312 in and in aluminum tubes 8 ft long with diameters from 2.000 to 0.125 in. Interval and continuous detonation velocity data were obtained. Under the test conditions detonation velocity was dependent upon explosive confinement and fracture-propping sand. The detonation velocity of a confined nitroglycerin explosion in aluminum tubes can be reduced by as much as 85 percent, when the tube contains fracture-propping sand. The shape of the reservoir, whether triangular or rectangular, has little effect on the detonation velocity or explosive propagation. The critical or minimum explosive-layer thickness between glass plates, capable of supporting propagation, was 0.0312 in. The presence of a fracture-propping sand in the sheetlike layers increased the critical explosive layer thickness to 0.0625 in. In nitroglycerin-filled and nitroglycerin-sand filled tubes, the minimum tube diameters successfully tested were 0.125 in and 0.375 in, respectively.

Jan 1, 1969

By S. Ralph Austin

Emanation coefficients of 950 samples of domestic uranium ore were successfully and rapidly determined with fair precision by modifications of the closed-can, gamma-only assay method, using commercially available or similar equipment. Coefficients range from <1 to 91 percent. Emanation varies considerably within each mine and area, but distinct differences among major mining areas were found, ranging from 7.5 percent for Moss Back Member, Chinle Formation, Southwest Lisbon Valley, Utah, to 56.6 percent for Ft. Union Formation (?), Powder River Basin, Wyoming. Coefficients also vary with (1) uranium mineralogy; (2) radium mineralogy; (3) lithology of host rocks; (4) grain size of uranium and radium minerals; (5) comminution of ore; (6) estimated porosity and permeability; (7) moisture content; (8) ore grade; (9) supposed mobility of deposits; age of deposits is unknown but limited by (10) age of host rocks which shows only doubtful correlation with emanation. Data obtained may be used to evaluate effects of investigated parameters on radon concentration in mines and thus to select efficient control measures. Drill-core emanation data allow estimates of probable radon problems in undeveloped deposits.

Jan 1, 1978

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Frederick Rhines

PURE copper that has been allowed to oxidize at an elevated tempera-ture in the air is found to be covered with two distinguishable layers of oxide scale. The outer of these, which is very thin, is composed of cupric oxide, while the inner layer, comprising the bulk of the scale, is made up chiefly of cuprous oxide (Fig. 1a). If a small quantity of an alloying element, such as silicon, is present in the copper, silica particles are found disseminated through the cuprous oxide, deposited most abundantly near the metal surface, and, in addition, silica particles occur to a limited depth within the copper itself (Fig. 1b). It is this inner layer, composed of oxide particles precipitated in a matrix of metallic copper that is known as the "subscale" or the zone of internal oxidation. Under a low oxygen pressure it is possible to produce the subscale without the formation of external layers of copper oxides, thus leaving the metal surface bright and apparently clean while oxidation has occurred, in fact, to a considerable depth within the metal (Fig. 2). Although little is yet known in a detailed way of the mechanism of internal oxidation, the general nature of the process is evident. By virtue of the considerable solubility of oxygen in copper,1 it is possible to bring the alloying element in contact with oxygen within the metallic solid solution. If the oxide of the alloying element is more stable than cuprous oxide, the foreign oxide may form and, since most oxides are relatively insoluble in copper, it will not long remain in solution, but will separate as a precipitate. As the metallic solute is exhausted in the zone of precipitation, oxygen that is constantly being supplied at the surface diffuses farther into the alloy and thus produces an ever-thickening shell of subscale. The distribution of the reacting elements in the subscale and adjoining zones must be somewhat as indicated in Fig. 3. The conditions requisite to internal oxidation to be anticipated are thus: (1) a solubility of oxygen in the alloy, (2) the ability of oxygen to diffuse at an appreciable rate into the alloy, (3) the possibility of the

Jan 1, 1940

By Raymond O. Dannenberg

The Bureau of Mines conducted laboratory and full-scale tests to develop a process for improving the flotation characteristics of lime-treated waste water produced by the Kennecott Copper Corp., Magna, UT. Unknown substances in the waste water reduced the flotation efficiency of the metal sulfides. An estimated annual loss of 795,000 lb Cu, 232,000 lb Mo, 5,625 tr oz Ag, and 617 tr oz Au would result from recycling the total flow from the lime treatment plant to the flotation mill in an effort to conserve water and reduce associated expense. The tests indicated that aeration or treatment with activated carbon significantly improved the water quality. The improvements in molybdenum recovery averaged 8 pct for carbon, 11 pet for activated carbon, and 16 pct for combined aeration and activated carbon. The combination of the two processes produced water quality as good as or better than normal feed water.

Jan 1, 2011

In 1910, he was with the Hidalgo Guadalupe, Pachuca, Mexico, and in 1911 was engineer with the Gualcola Mines Co., at Tuquerres, Colombia. In 1913, he returned to the Sout.hwest, and was employed for that yea.r by the Inspiration Cons. Copper Co. at Miami, and in the middle of the following year he became engineer with the Detroit Copper Co., at Morenci. In the autumn of 1914, Mr. Reece, stirred by his English blood, resolved to return to England to take part in the war. At this time he wrote "I think it will be better for me to resign my membership. If I come through all right, I will apply for re-election." The Institute, however, instead of accepting Mr. Reece&apos;s resignation, voted him an indefinite leave of absence, and this precedent soon crystallized into the regular procedure, now in force, of remitting the dues of members in active service. On Dec. 17, 1914, he wrote from Montreal that he fully expected to go over shortly in the second contingent from Canada, with Borden&apos;s Armored Brigade, operating with armored motor cars. As he said "this will be active enough service to satisfy any enthusiast, as they are used generally for reconnaissance duty." Soren Ringlund Soren Ringlund died suddenly on July 24, 1918, at Fort Logan, Colo., where he was engaged in service with the Medical Department of the U. S. Army. Mr. Ringlund was born in Denmark in 1875. He came to the United States in 1902, and became a citizen in 1908. He graduated as

Jan 1, 1920

By Alan D. Fisher

Amtrak made a decision to replace an aging bascule bridge with a vertical lift bridge for their crossing of the Thames River in New London, Connecticut. The new lift bridge occupies the same alignment and shares the same foundations as the bascule span. During construction the deep foundation caisson supporting the bascule span settled and tilted. Investigation into possible reasons revealed interesting historical facts, both of the construction of the innovative open well caisson foundations and of the state-of-the-art in tremie concrete placing methods in use at the turn of the century. This paper describes both of these topics.

Jan 1, 2008

By S. F. Guo, Z. F. Zhan, X. L. Huang, Y. Zou, S. W. Qi

"FLAC3D is an important numerical analysis software to study dynamic response of rock slope. In application of the program, the common issues such as absorbing boundary and the method to apply wave have been well studied. However, effects of model mesh size, damping and width of slope are still unknown. In order to make the result more convictive, this article has discussed the above issues systematically. It found that when the maximum mesh size is smaller than 1/10~1/8 of the smallest wavelength, the mesh size is smaller, the computational accuracy is higher. Meanwhile, values of damping and width of slope have no effect on the result. Additional, results of FLAC3D modeling on wave transmission across rock joints agree well with analytical solutions, so it has verified the capability and accuracy of FLAC3D on dynamic response of rock slope.INTRODUCTIONChina is a mountainous country accompanied with many earthquakes. Thousands of geological disasters are triggered by the Wenchuan Earthquake in Sichuan Province, and the majority of the disasters are landslides induced (Xu et al., 2009). Meanwhile, the paper (Li et al., 2003) points out five significant issues about dynamic loading in the area of geotechnical engineering, which includes the study of rock slope stability under earthquakes, and the dynamic response of rock slopes is one of its important study issues."

Jan 1, 2015

By E. Douglas, V. M. Malhotra

"This report presents the results of a laboratory study undertaken to evaluate ground granulated blast-furnace slag from Algoma Steel Corporation, as a replacement for Portland cement in cemented mine backfill. The evaluation was based on the results of compressive strength tests performed on cylinders cast from mixtures made with a granulated blast-furnace slag and tailings from four different mines in the Sudbury basin. Various percent¬ages of slags and various binder to tailings ratios were used.Tests results show that, in terms of compressive strength, the slag performs as well or better than Portland cement as the binding agent in cemented mine backfill. Lime was found to be a poten¬tially good activator for ground granulated slag in mine backfill applications.A field test was conducted at one of the mines, consisting of placing a mixture of 95.5% ground granulated slag and 0.5% lime into a stope, and inspecting the floor slab as it hardened. The slag performed as expected, considering the backfill mixture proportions used and the preparation of the test site."

Jan 1, 1989

By S. P. Ball, A. J. Monhemius

In a laboratory study under acidic oxidising conditions, the thiocyanate system gave results at least as good as cyanide and considerably better than thiourea, with modest consumption of SCN (less than 1 kg/t ore). For both cyanide and thiocyanate lixiviants a residence time of about 24 h was required for maximum gold extraction, which was generally in the range of 92-96%. The adsorption of gold from thiocyanate leach liquors was found to be rapid, but activated carbon catalyses the autoreduction of ferric iron to ferrous iron in thiocyanate solutions, suggesting that ion exchange may be a better recovery route

Dec 1, 1995

Excavations in rock are commonly supported with wire mesh, shotcrete, wire mesh and shotcrete in combination, and shotcrete reinforced with various types of fibres. Wire rope lacing and various types of straps are additional forms of support installed over the above types, to cope with severe conditions. These support systems are very important items of ?membrane? rock support. With the recent development of several types of thin sprayed linings, the importance of membrane support is likely to increase in the future. In this paper, a wide range of mechanisms of membrane behaviour and mechanisms of loading of membranes, is described. The concepts of membrane components, which are single membranes that may be used on their own as rock support, and membrane systems, which are combinations of more than one membrane component, are introduced. Different situations have different requirements of membrane support, and differences between civil engineering and mining requirements are highlighted. With the different basic requirements in these two areas, the requirements of rock support are correspondingly different. A thorough understanding of the mechanisms of behaviour of the different types of membranes, and the different mechanisms by which the membranes are loaded, is essential before a selection of appropriate support can be made, before appropriate design methods and calculations can be determined, and before appropriate performance test methods for membranes can be defined. The material in this paper contributes towards the understanding of membrane support behaviour.

Jan 1, 2001

The objective in control blasting is to reduce overbreak to control the final pit wall slope, shaft, drift, ditch, bench, etc. to the final planned excavation limit.

Jan 1, 1990

Media Type Effect on Grinding Efficiency

Sep 13, 2010

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Paul Zinner

An exhaustive program of geologic studies and mapping has been conducted by the Geological Survey in the Iron River district of Michigan since May 1943. Means of contributing to the success of these studies were sought by the Bureau of Mines, and eventually a program involving geophysical studies and core-drilling was undertaken in the area. All of the work was done either to develop data that would contribute directly to geologic studies or to investigate geophysical methods that might be used as a primary means for the discovery of minable iron ore.

Jan 1, 1949

Ground support audits are sometimes necessary in ageing underground mines. Usually, the purpose of such audits is to assess the state of the ground support in various parts of the mine, identify areas that require attention and establish rehabilitation requirements. In 2005, Brunswick Mine, located in Bathurst, New Brunswick, Canada, completed a comprehensive mine-wide ground support audit. The areas examined included excavations in several mining blocks, as well as ramps, shaft stations, garages, shops, etc., throughout the mine. A vast amount of data was collected over a period of two weeks by multiple auditing teams. The audit was followed by a data digitisation exercise, and the creation of a data management system to store audit results and keep track of subsequent rehabilitation activities as they occur. One aspect of the data management system was the incorporation of a function for reporting on ground rehabilitation progress, along with the capability of updating mine level plans for easy visual presentation of this progress. This article describes the approach implemented at the mine to carry-out the audit, as well as the database constructed to manage the results.

May 1, 2009

By L. Dr. Edeleanu

CRUDE petroleum is a mixture of various groups of hydrocarbons and some bodies containing oxygen or sulphur. These constituents possess properties differing considerably one from another and the proportion in which they are contained in the crude oils is also very different. Owing to this complicated composition the practical use of crude petroleum is much restricted. For example it is sometimes used as a liquid fuel. But its employment in this way is uneconomical because various valuable qualities of the individual constituents are not made use of. The rational utilization of petroleum can only be accomplished if the various groups of hydrocarbons are separated. The mixture of hydro-carbons present in the crude oil must be split up in such a way that the hydrocarbons are divided into various groups having certain predominant characteristics and uses. To accomplish such a separation is the aim of the technical refining of petroleum. ORDINARY REFINING BY DISTILLATION AND CHEMICAL TREATMENT Hitherto this has been accomplished by two processes, namely, fractional distillation and chemical treatment of the distillates obtained. Distillation Process The process of distillation consists in the separation of the constituents of petroleum into various fractions, the boiling points of which lie within certain defined limits. The fractions so separated possess certain special qualities in common, which enable them to be applied for specific purposes in practice. For example, we have the fractions known as benzene, illuminating oils, heavy oils, lubricating oils, etc.

Jan 9, 1914

By D. Hoffmann, S. Plumb

IRUP is an iron-rich ultramafic pegmatite rock that formed due to hot ironrich fluids and gases replacing local stratigraphic zones of the Bushveld Complex. This study focuses on the estimation of the probability of IRUP occurrence on the Merensky Reef at the Marikana Karee Mine. A 2.15 million centare IRUP-rich domain at the Karee Mine was initially defined from the interpretation of a surface aeromagnetic anomaly, and exposures in the mine workings. Surface boreholes (spaced 250-500 m apart) within this IRUP domain contain approximately equal numbers of IRUP-replaced and IRUP-free intersections. Owing to the uncertainty in the continuity of the IRUP alteration (a result of the wide borehole spacing), the risk associated with the development of mining infrastructure within this domain is unquantifiable. Semi-quantitative data comprising visual estimates of IRUP replacement from reef development mapping data and surface borehole reef intersections was interpolated into blocks using indicator kriging estimation. Comparative analyses of the estimate of IRUP occurrences were made by changing the block size and declustering the data systematically. Reconciliations of the probability of IRUP predicted from the block models derived from the different data-sets and sequential indicator simulation models were analysed for four mining study blocks. A quantitative approach to modelling the occurrence of IRUP can be an additional tool for refining the estimate of the geological losses that inform the mine plan in such high-risk zones.

Jan 1, 2015

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

The effect of composition on electrical conductivity (resistivity), viscosity and liquidus temperature of the slags encountered in electric smelting of PGM-containing suphide concentrates is reviewed along with the relationsip between slag composition, slag-matte separation and metal losses to slag. Optimization of slag composition at furnace temperature is attempted on the basis of opposite and parabolic trends of the viscosity-conductivity relationships of the slags. The importance of surface tension of slags is emphasized using available and estimated information, which are grouped into a useful correlation. These values are coupled with or incorporated into slag viscosity plots to illustrate the correlation between the two factors which influence slag-matte separation as well as refractory attack. The electrode in the slag-resistance furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power. The obvious parameters are the size and positioning in the slag bath, which are defined by slag resistivity, furnace resistance, cell constant and power input. The flow of heat generated by the electrode current determines the energy distribution and furnace dimensions creating viscosity profiles, which in turn affect flow conditions. Thus the flow of slag and matte isdiscussed in conjunction with the furnace geometry, stirring action of the electrodes, buoyancy and electromagnetic effects. The action of the electric furnace as a settler is discussed. The rectangular furnace is considered as a channel reactor in this analysis and the action of the electrodes is described to indicate a balanced settling rate in the area of electrode action. Discussion of the design and production capacity of the electric furnace with reference to operating current, power input, furnace dimensions and electrode size are based on considerations derived mainly from slag properties such as its resistivity, viscosity and liquidus temperature.

Jan 1, 2004