Search Documents

By T. H. Alden

BaCKOFEN, Avery, and Turner have shown"2 that the large tensile elongation in superplastic metals is correlated with a high strain-rate sensitivity of the flow stress. At present, the reported superplastic materials are complex eutectic or eutectoid systems with a large solubility range in at least one of the terminal phases. This note describes the behavior of a solid-solution alloy (at 22°C)5,= Sn-1 wt pct Bi, which has been processed in order to produce a fine grain size.2,3,6 The chill-cast, 1/2-in.-diam ingot was homogenized for 1 week at 130°C, extruded at O°C to 0.083 in. diam, quenched within 15 sec, and stored at -196°C. Samples were warmed to room temperature 16 hr prior to mechanical testing or metallography. During tension testing at room temperature, it was found that the flow stress reached a steady-state value which depended on the imposed elongation rate and was independent of strain to an error of about ±5 pct. In Fig. 1 is plotted log a vs log e where a is the measured steady-state flow stress and i the imposed strain rate. These quantities were calculated using "instantaneous" area and length to an accuracy in the sample diameter of ±5 x 10-4 in. The log a-log 1 curve is sigmoidal. The strain-rate sensitivity, which may be given by d log old log 6,' has a maximum value of about 0.48 between i = 5 x 10-4 and 5 x 10-3 per min. The value is well above frequently measured values for metals at creep temperatures (0.1 to 0.3) and comparable to the rate sensitivity for Pb-Sn solder: which has been shown to be superplastic.2,3 Note, however, that below or above the strain rate of 10-3 per min the rate sensitivity of Sn-1 pct Bi decreases and at high rates is more nearly like that of conventional metals. The grain size of this material is relatively uniform, Fig. 2, and may be specified by an average linear intercept i.' Grain growth occurs at room temperature but after 16 hr, L = 5. Tensile elongation was measured on finer-grain-size specimens, which had been at room temperature 15 min prior to testing. After 15 min, the samples are fully recrystallized. Three strain rates, 5 x 10-3, 10-2, and 2.5 x 10-2 per min, were employed for which the measured elongations varied from 425 to 500 pct. These results would seem to justify the term superplastic, applied to this alloy, although the ductility is inferior to that of the Sn-Bi eutectic.3 The Sn-1 pct Bi alloy, which is a single-phase material with equiaxed, fine grains, is an excellent one on which to make an estimate of the Nabarro-Herring9 creep rate. According to the model of Avery and Backofen2 a substantial part of the deformation must be accomplished by N-H creep in the strain rate-temperature regime in which d log a/d log 1 = 0.5. The maximum N-H creep rate is given by9 L2kT where v is the atomic volume and D the self-diffusion coefficient. For this test v = 3.O x 10-23 cu cm, D = 1.4 e-23,300/RT = 2.5 x 10-l7 sq cm per sec,7 L = 5x 10+4 cm, T = 295°K, and a = 2000 lb per sq in. = 1.38 x 10' dyne per sq cm. The calculated creep rate is E= 4 x 10-11 per sec which may be compared with the measured creep rate at this stress, Fig. 1, of 6.7 x 10-5 per sec. The N-H creep rate is seen to be negligible. Earlier consideration2 of this question was in error because incorrect diffusion coefficients were used. The assistance of R. R. Russell in metallography is acknowledged gratefully.

Jan 1, 1967

By R. J. Smyth

A Steel Compression Reinforcement Repair Technique (PetroSleevel) system has been developed that has the ability to repair pipeline defects such as stress corrosion cracking (SCC) without requiring welding to the operating pipeline. The Technology has been used to repair active cracking in ERW seam and cracking in the pipe body. All repairs were performed while the pipeline was in operation. This paper will discuss the engineering theory, testing performed to verify the engineering theory, and examples of actual sleeve installations.

Jan 1, 2005

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By R. Radhakrishnan, C. Gunasekaran

"Calicut Bypass Phase-II project included construction of 7 m high embankment over soft compressible clays up to 18 m in thickness. Approx 1.5 km length of road out of a total 5 km length consisted of abandoned paddy fields which were low lying, waterlogged and marshy in nature. On the basis of excellent results achieved in earlier phases of the by-pass construction, ground improvement work by installing pre-fabricated vertical drains (PVD) was undertaken to stabilize the embankment foundation along the weak clay areas prior to road pavement construction to avoid large post construction settlement as well as to improve the lateral stability during and after embankment construction. This project perhaps stands out as one of the highway projects completed within a very short time period of total 18 months including four month long heavy monsoon period, when embankment construction was not possible and construction of two bridges across rivers. All activities including the ground improvement had to be programmed and completed within the shortest time period possible. The paper discusses details of the extensive ground improvement and soil instrumentation carried out for the project and will illustrate how careful planning and execution can reduce the period required for highway projects involving ground improvement.INTRODUCTIONPhase-II construction of Calicut by-pass was undertaken on a priority basis by the State of Kerala in 2014. The main contract was awarded to M/S ULCCS Ltd, Kozhikode, Kerala and the ground improvement work was awarded to M/S Geo-Enviro Engineers P Ltd, as specialist agency to design and execute the work.Soil investigation carried out confirmed thick soft clay deposits below GL in three areas along the road alignment totaling approx 1.5 km in length. These areas were low lying, waterlogged and marshy in nature. Highway embankment had to be constructed up to 7 m in height above existing GL to form the proposed road alignment along these areas. On the basis of excellent results achieved in earlier phases of the by-pass construction using pre-fabricated vertical drains or PVD (R. Radhakrishnan, 2006), ground improvement using PVD had been included in the contract to stabilize the embankment foundation along the weak clay areas prior to highway embankment construction to avoid large post construction settlement as well as to improve lateral stability during its construction."

Jan 1, 2015

By C. S. Kucukkargoz, A. Bhalla

"The solid-state reduction of ilmenite concentrate with graphite was studied under argon atmosphere at temperatures between 1050°C and 1350°C. The rate of reduction increased with increasing temperature and decreasing particle size, with the maximum extent of reduction found to be 80% at 1350oC with a particle size in the range of -106 +90 µm. The activation energy for the reduction reaction was calculated to be 257 kJ/mole. The trivalent iron oxide was reduced first to divalent iron oxide and then to metallic iron. An annular ring of a partially reduced oxide phase containing metallic nuclei was formed around the core of ilmenite, which grew in size as the original ilmenite core shrank with progressive reduction. The reduction of titanium dioxide also took place during this stage, which produced the Magneli oxides in the form of TinO2n-1. The metallic phase had very high Fe and low Ti contents throughout the reduction, whereas the partially reduced oxide phase adjacent to the metallic phase was high in Ti and depleted in Fe. The metallic phase globules formed during this stage were small and are considered suitable only for leaching and not for other concentration processes. The core of the particle generally retained the composition of the original ilmenite. The purpose of this work was to remove iron and increase the titanium oxide content of the ilmenite to produce a high-titanium containing charge for subsequent smelting.IntroductionThe titanium-bearing minerals ilmenite (FeTiO3) and rutile (TiO2) are the primary natural raw materials used in industry to produce titanium metal and titanium-based products. The common titanium-bearing minerals are ilmenite, rutile, anatase, brookite, leucoxene, arizonite, and perovskite. Although the formula of ilmenite is commonly expressed as FeTiO3, the mineral can accommodate Mn and Mg, which are chemically bound in the form of (Fe,Mn,Mg)TiO3. Ilmenite concentrate can also contain Fe2O3 and Al2O3 in addition to the physically separable oxides such as SiO2 and CaO. The crystal structure of ilmenite is an ordered derivative of the corundum structure with a trigonal-rhombohedral symmetry. Fe2+ and Ti4+ ions occupy the octahedral sites, leaving the tetrahedral sites unoccupied. In each FeTiO3 unit, there are three O2- ions creating three octahedral sites, two of which are occupied by Fe2+ and Ti4+ (Wilson et al., 2005)."

Jan 1, 2017

By Q Qu

Reliable prediction of longwall gas emission sources and rate plays a critical role in mine ventilation and methane drainage capacity planning. Over the years, Australian longwall mines have been using the historic Winter method and the Flugge method in modelling specific gas emissions (SGE). The predicted results often experience high discrepancies from the operational reality. To improve gas emission prediction, post-mining gas contents were measured in several mines in Qld and NSW by safely drilling core holes into the longwall goaf. The results revealed many new insights into gas emission characteristics from different coal seams and the drawbacks of the European methods in their use in high-production gassy Australian longwall mines. Based on measurement data, a new, time-dependent gas emission prediction model has been developed. Considering several factors such as caving, desorption and production rate, the new model can predict more accurate and meaningful gas emissions to meet today’s needs in mine gas emission management. A case study is provided to demonstrate the application of the new SGE model.

Oct 12, 2022

"Placer Dome Inc.'s Dome Mine is located in South Porcupine, Ontario and has been in production since 1910. In the past, the mill leach circuit was preceded by preaeration and primary filtration circuits. These circuits were operated to overcome the effects of pyrrhotite in the ore which reacts with cyanide to form cyanates and thiocyanates and also consumes oxygen.In early 1989, primary filters were by-passed for an extended period. Actual plant results showed no affect on gold recovery or cyanide consumption so the circuit was left off-line permanently with significant cost savings.In 1990 it was determined that considerable savings could be realized underground if backfill storage facilities were located in the mill. It was decided to convert the preaeration pachucas to backfill storage tanks on a trial basis. The trial proved successful with no effect on recovery or significant increase in reagent consumption occurring due to the elimination of the preaeration circuit. The converted pachucas worked well as backfill storage tanks.Modifications such as these have helped to keep the Dome's millings costs among the lowest of Canadian gold producers."

Jan 1, 1992

By C. Lumley

The management of the Anglo Platinum (AP) mining technical systems (MTS) embarked upon a process of defining the strategy for the MTS department. The newly established department forms part of the greater Group Information Technology (IT). The strategic process took place within an environment that had witnessed a dramatic proliferation of IT implementations across the group within the last three years. The IT department has been structured in terms of the classical plan, build and run functions with the applications and integration streams running perpendicular across these three functions. The application stream is divided into commercial and mining technical systems with business systems integration the third stream. The mining technical systems department supports mine management to effectively gather, analyse and disseminate data relating to the ore reserve by integrating a number of strategically selected IT applications to ensure that the safety, legal and operational requirements are met. This service to business is rendered by management of a strategic outsource partner via tightly controlled service level agreements (SLAs). The framework used for creating a mining technical systems department that is empowered to add value to business was formulated using the AP value chain as both the starting point and guiding process to ensure alignment to the greater internal strategy of the business. Keywords: Platinum, Mine planning, Mining technical systems, Value chain.

Jan 1, 2003

By H. Walqui

This paper describes operating gains resulting from standardizing operating and maintenance practices to improve the performance of the pebble crushing circuit at he Empire Concentrator. Past efforts have led to improved operating time but no additional throughput gains. New Operating standards and checklists were developed and introduced. The content and frequency of the review process indicators was then changed to take advantage of the new practices resulting in an increased feed rate and availability through the pebble crushing circuit.

Feb 27, 2013

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989

By Ângelo Siqueira da Silva

Este trabalho teve por objetivo avaliar o potencial gratifizante de adições de alumínio, em conjunto com inoculante a base de silício, diretamente no fundo do basquete antes do basculamento da panela de metal líquido no basquete da máquina centrífuga, a fim de produzir tubos centrifugados de ferro fundido nodular de matriz majoritariamente ferrítica. Amostras extraídas da ponta e cabeça dos tubos, sem e com distintas adições de alumínio, foram submetidas a tratamentos de recozimento (1050, 1000 e 900ºC), a fim de serem analisadas por meio de análise microestrutural e dureza Brinell. De acordo com os resultados obtidos a incorporação de alumínio ao ferro fundido foi mais efetiva para a incorporação de 1,7% de Al no ferro fundido, permitindo obter um ferro fundido nodular de composição ligeiramente hipereutética, com adequada grafitização e matriz 100% ferrítica, mesmo nas condições testadas com menor temperatura de encharque (900ºC) no recozimento, e com dureza dentro das especificações para a aplicação.

Aug 16, 2017

By Gary Cavanough, Stuart Addinell, Hector Parra

Drilling deep, straight, accurate holes in hard rock to achieve efficient blasting is a challenge for the mining/quarrying industries with short holes normally drilled using “top hole hammer” (THH) and deep holes using “down the hole Hammer” (DTH).

Jan 1, 2013

By Mônica Aline Magalhães Gurgel

Nas últimas décadas o setor siderúrgico vem desenvolvendo aços com maior valor tecnológico, surgindo assim várias classes, entre elas os aços avançados de alta resistência, onde encontra-se o aço bifásico ou “Dual Phase” (DP). Este aço é caracterizado por uma microestrutura ferrítica-martensítica, associada a uma matriz ferrítica com ilhas dispersas de martensita. Neste trabalho utilizou-se amostras de um aço baixo C e Mn, com micro adição de Nb e Mo, em desenvolvimento, onde se propôs uma avaliação da evolução microestrutural e propriedades mecânicas das amostras extraídas após a laminação a quente, a frio, seguida de recozimento intercrítico, em escala laboratorial, com auxílio de forno Mufla e um equipamento de análise termomecânica (TMA), resultando em taxas de aquecimento distintas, onde selecionou 7 temperaturas de encharque distintas e subsequente resfriamento com patamar isotérmico a 600°C por 20 minutos, onde observou-se que para esse ciclo a microestrutura com aspectos mais característicos de um DP se deu em tratamentos com temperatura de encharque entre 760 e 800°C.

Aug 17, 2017

Study on Influence that Styrene-Phosphoric has on the Surface Property of Rutile Minerals

Sep 13, 2010

By AIME

THE wind howls almost incessantly over the mining engineers working in the near desert that is the Division of Namaqualand, the upper Atlantic coastal corner of South Africa's Cape of Good Hope Province. But when these men at the U. S.-owned mines called Nababeep South and East O'okiep (pronounced Oh-keep) tell you about their achievements, they can be heard above the wind. For their O'okiep Copper Co. Ltd. now produces over half the Union of South Africa's annual output of 30,000 tons of copper metal. Moreover, it is a very decent sample of U. S. geotechnical imagination. financial daring, and managerial skill, all operating successfully in a

Jan 1, 1947

The term slag has been used to define a wide variety of material including mine spoil and slag produced at steel plants. The present paper is concerned only with the non-metallic alumino-silicates developed simultaneously with iron in blast furnaces.The control of iron quality by slag has long been appreciated but here aspects of slag control based on concurrent iron production are indicated. Consideration is given to the basic composition of slags relative to the type of allotrope required. Up to a point, the plant conditions, under which a particular slag type is processed, have some effect, but these conditions only widen the range of a given allotrope.They do not convert one slag type into another. The nature of the slag types and experiments with additives to convert one slag type into another are discussed.The various uses for allotropes of blast furnace slag are considered.Their use in air cooled slag, foamed slag, slag wool, cements, soil stabilization, glass bottles, and building bricks and blocks, is explored in some detail.INTRODUCTIONWithin recent memory, blast furnace practice has been solely concerned with the production of iron. The slag make at this time had not reached embarrassing proportions. In Britain, unlike Germany, no legislation existed to prevent the growth of unsightly slag banks. Generally slag found limited use as fill and road material in the immediate plant vicinity. This is broadly the case in Australia today. In Europe and America, where the slag make is of the order of several million tons annually, the room problem and the cost of dumping slag has stimulated commercial and scientific research on the disposal problem. Currently, most iron plants in Europe can profitably dispose of at least 95 per cent of their slag make.

Jan 1, 1964

By D. Keech

The Conveyor Equipment Manufacturers Association (CEMA) specification B105.1 “Welded Steel Conveyor Pulleys” adequately defines standard pulleys for most aggregate material handling applications. However, many aggregate applications demand pulleys of higher capacity and reliability than that offered by CEMA pulleys. This paper examines the CEMA Pulley Standard and pulley specifications for aggregate applications requiring greater capacity and reliability than the CEMA Pulley Standard. Higher reliability increases the uptime and has a lower total cost of ownership.

Jan 1, 2003

By Richard L. Rains

The Bureau of Mines made a study of mines and prospects of the Benton Range RARE II area (No. 5056), Mono County, California in October and November 1980. The study area is west of Owens Valley and 30 mi (40 km) north of Bishop, California. The mineral deposits were evaluated by examination of mines, prospects, and mining claims by the Bureau of Mines. Geological, geochemical, and geophysical studies were conducted by the Geological Survey. The principal mineral commodities of the Benton Range RARE II area are gold and silver but tungsten deposits may also extend into the area. Properties with resources are listed in table 1; their locations are shown on figure 1.

Jan 1, 1982

By Keith Heasley

In many practical situation where the LaModel program in used to analyze the mechanical response and failure of the mining environment, there are very few actual field measurement from the site available for deriving the appropriate input parameters. For coping with this typical lack of field data, this paper presents some recommended calibration techniques derived from on an in-depth understanding of the laminated model formulation and from many years of experience applying LaModel to practical situations. For each of the critical input parameters (rock mass stiffness, gob stiffness and coal strength) in LaModel, a specific calibration technique is recommended and presented along with the justification for the technique and some appropriate derivations/equations for assistance. It is hoped that this frank discussion of recommended calibration techniques can help novice LaModel user develop better models and can initiate a discussion among rock mechanics experts on how to improve upon the presented techniques.

Jan 1, 2008

By M. Deal

Particle size analysis is a fundamental measurement utilized in the mining industry, especially in comminution, hydrometallurgy, and mineral processing. While sieves and cyclosizers are the standard methods used to determine particle size distributions, in recent years alternative instruments have been developed that claim to provide more rapid and equally reliable results. Newmont Metallurgical Services has implemented the use of two such instruments, along with traditional methods (sieves and a cyclosizer), on a daily basis. The Malvern Mastersizer 2000 laser analyzer is a wet sample system that can analyze particles in the size range 0.02µm to 2000µm, and the Horiba CAMSIZER® is a dry system that can analyze particles in the size range of 30µm to 30mm using digital image processing. A comparative analysis has been performed to determine the applicability of each particle sizing method in laboratory testing.

Jan 1, 2011