Search Documents

By Joe Milbourne

The potential for treating copper-nickel-cobalt-platinum group metal concentrates by a fully hydrometallurgical route is discussed. Processes specifically developed for treating these feeds and the potential application of the processes developed for the treatment of chalcopyrite copper concentrates are included in the evaluation. Block flowsheets are provided and the technical characteristics of various processes are compared. The current state of development for each process is summarized and probable economic impacts of the technical features are qualitatively assessed. Perceived risks and rewards associated with each technical concept are provided in the conclusions.

Jan 1, 2003

By A. S. Mustafinova, A. A. Zharmenov

"Production of electrolytic copper is characterized by large volumes of acidic spent solutions the utilization of which requires considerable expenditures of neutralizing agents. At present, an economically substantiated technology does not exist for treatment of sulfuric acid rinse solutions and spent copper electrolyte which will allow for repeated use of the acid and the metal salts. Therefore, for this aim the most advantageous is the use of electromembrane methods. In the paper there is stated the essence of developed technologies which are distinguished by low waste and provide the extraction from the solutions of metallic copper, nickel and sulphuric acid. There are also considered methods of copper electrolyte processing allowing to regulate its composition by that or another component (H2S04, Cu, Ni, As).On the base of the detailed study of the behaviour of various types of ion- exchanger membranes in copper-, nickel-, zinc-, arsenic- bearing sulphate solutions there is realized the selection of the most suitable membranes (MK -401, MA-411, MB-2 and MKL-l/MAL-2).Some variants of electro membrane processing of spent solutions of the hydrometallurgy process have passed productions tests on a number of copper-electrolyte enterprises of the countries of CIS (cooperation of Independent States). These tests showed high efficiency of developed methods."

Jan 1, 1997

By D. L. Stewart

"Melt loss is usually one of the highest individual cost items in the operation of ah ingot casting facility. While melt loss and the resulting cost for the entire facility is usually well known (at least via standard cost accounting), dross generation and melt loss for individual unit operations within the plant are usually not known. Thus, the financial impact of various practices, alloys and scrap types is not known. Development of an accurate, relatively low-cost technique for measurement of melt loss at commercial scale would aid in understanding melt loss for existing units, as well as evaluation of the melt loss impact of alternate processes.This paper will describe a methodology developed at Alcoa for accurate and inexpensive measurement of melt loss at commercial scale. The methodology has been used to evaluate the impact of scrap type, melting practices, and dross treatment technology on melt loss."

Jan 1, 2000

By Eiki Ono, Atsushi Yamatodani, Shigeru Sunagawa, Yasushi Takasaki, Atsushi Shibayama, Yasunori Higuchi

"During metallurgical processing of non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product.In this research, some experimental feasibilities were investigated to recover/remove Cu and As from the residue. Primarily, the removal of As and volatilized materials from the residue was examined by pyrometallurgical treatment (dry-process). In the second stage after treating the residue with a dry-process, leaching and solvent extraction as hydrometallurgical treatments (wet-process) were also investigated by using H2SO4 solution as a two stage leaching treatment, to dissolve various metals from the leach residue. Then, solvent extraction was examined by using LIX-84I as an extractant to recover and separate Cu from impurities from the final (2nd) leached solution. For the leaching stages, the removal of 90 % As and the leaching rate of 85 % Cu could be achieved by 0.25 mol/l and 1.0 mol/l H2SO4 solution, respectively. On the other hand, the extraction of over 90 % Cu and stripping was carried out by solvent extraction. 1. IntroductionIn metallurgical process for non-ferrous metals, smelting residue (inc. smelter slag, flue gas and so on) is inevitably generated as secondary product, i.e., flue dust, slug and so on. The smelting residue includes some useful metals and undesired toxic materials; Cu, Pb, Ca and As, etc.In Japan there is one undisclosed place stockpiled with 10,000 ton of smelting residue from abandoned smelters about 25 years ago. Therefore it is necessary to reduce the residual amount for space and environmental protection including water treatment by separating and removing toxic materials."

Jan 1, 2008

By F. J. Tavera

A study on the electro kinetics of lead carbonate, silica, and alumina, in aqueous media was carried out at different pH values. The behavior of potential was determined for these species in the pH range between 3 and 12. Homocoagulation of lead carbonate in aqueous media is analyzed at its isoelectrical point. Lead carbonate heterocoagulation is analyzed with silica, alumina, and silica ? alumina mixtures at low pH values. The experimental results are considered for their possible application to treat residual water polluted with lead.

Jan 1, 2006

By Jorge Alberto Soares Tenório, Denise Crocce Romano Espinosa, Luciana Harue Yamane

"The present work investigated the influence of Fe+2 initial concentrations in the bioleaching of copper from printed circuit board using Acidithiobacillus ferrooxidans-LR. Printed circuit boards were collected from obsolete computers and mechanically processed through size reduction followed by magnetic separation. The bacteria Acidithiobacillus ferrooxidans-LR were grown and adapted in presence of printed circuit boards. A shake flask study was carried out on the printed circuit boards samples (non-magnetic fraction) using a rotary shaker under the following fixed conditions (185 rpm, 30°C). The bioleaching efficiency was evaluated by comparison between the concentration in the initial sample and in the leached liquor, pH of the medium and concentration of ferrous iron produced. Inductively coupled plasma optical emission spectrometry (1CP-OES) was used to determine the metals concentration. The results showed that Acidithiobacillus ferrooxidans-LR leached 63% copper from printed circuit boards using supplemented medium with Fe+2.IntroductionThe waste of electric and electronic equipment is generated by discarding of equipment such as obsolete computers and cell phones which is stimulated by the technology innovations and it has been growing each year. Because of the amount that has been accumulated it has become a prominent environmental problem but also can be a source of valuable materials, such precious and base metals [1,2] The printed circuit boards are found in almost all electric and electronic equipment being composed of polymers, ceramics and metals and can be an alternative source to recover base and precious metals. The precious metals are used in the printed circuit boards to protect against oxidation and base metals because of its conducting properties [3]. The heterogeneous composition of printed circuit board is a limiting factor in the recycling processes and the metals concentrations also range."

Jan 1, 2011

Testing is in progress to address compatibility issues with regard to long term storage of plutonium in contact with two different intermetallic systems. The two intermetallic systems are: 1. dental amalgam, i.e., mercury plus silver alloy powder, and 2. liquid gallium alloy plus copper powder. Both of these are plasto-metallic materials that undergo a solidification reaction at room temperature. Each system is allowed to react in contact with both high-purity alpha plutonium and a delta stabilized plutonium alloy at varying temperatures in an argon atmosphere. Wetting characteristics and possible interaction will be studied metallographically in the post-mortem condition. Complete results including metallographic examinations will be presented.

Jan 1, 1995

By J. W. Whitney

Itronics Inc., through its wholly owned subsidiary Itronics Metallurgical, Inc. (IMI), has successfully developed technology that allows it to be fully integrated as a photochemical recycler. IMI is now using this technology to expand its regional operation, which collects used photographic chemicals, chemically removes 99.997% of the silver and uses the residual to make a line of high quality liquid multinutrient liquid fertilizer products. Elevated silver discharges from the Reno-Sparks sewage treatment facility, that were traced back to incoming waste photographic chemicals and which were seriously impacting the sensitive fishery, provided the impetus for this project. This paper is updated from a paper presented at the Twenty-Second International Precious Metals Conference Toronto, Ontario, Canada in June 1998. It presents an overview of the scope of the problem solved by the technology, some of the permitting and development issues, and some of the specific fertilization formulations that are now being marketed.

Jan 1, 2000

By N. S. Narayanan

Monazite, one of the major sources of rare earths, is normally opened by digestion with hot concentrated caustic soda solution. Caustic digestion dissolves phosphate and leaves a hydrated mixed metal oxides cake containing thorium, uranium and rare earths. By leaching this cake with hydrochloric acid at pH 3.0 to 3.2 bulk of the rare earths are preferentially removed and separated. The slurry left after removal of major portion of rare earths contains all the thorium and uranium present In the feed monazite. In addition this slurry also contains substantial quantities of rare earths. Solvent extraction tests were carried out to develop a process to separate rare earths, thorium and uranium present in the mixed chloride solution obtained by dissolving the above slurry in hydrochloric acid. Based on these tests a solvent extraction flow sheet was developed with di-2-ethyl hexyl phosphonic acid mono 2-ethyl hexyl ester as the extractant. The details of experimental work and results obtained are discussed and a flow sheet for processing monazite Incorporating the new process is suggested.

Jan 1, 1997

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By Sergio Neves Monteiro, Nuã Simonassi, Helvio Pessanha Guimarães Santafé Jr.

"Thermoset polymers, like the polyester, become harder with increasing temperature owing to molecular crosslink formation, which is a thermal benefit for composite matrix applications. Natural lignocellulosic fibers, however, have low thermal resistance and tend to degrade with increasing temperature. Therefore, the combination of a lignocellulosic fiber, as reinforcement, with a thermoset polymer, as the matrix, results in a composite material with complex thermal behavior. In the present work, a thermal analysis was conducted on polyester composites with different amounts of coir fibers. Both TGA and DTG curves were analyzed to determine the effect of the coir fiber on the thermal resistance of the composites. It was found that the coir fiber sensibly affects the thermal behavior of the polyester matrix for fiber amounts above 10% in volume. This effect is associated with an increase in thermal degradation.IntroductionIn recent years, there has been an increase application of natural fibers as reinforcement of polymer matrix composites in several industrial sectors, with special participation in automobile components [1-3]. Figure 1 illustrates the different components of a modem BMW sedan that are fabricated with lignocellulosic reinforced polymer composites."

Jan 1, 2012

By Bernd Kopacek

"Nowadays more and more consumers substitute their conventional TV-sets and computer monitors by LCD panels. In the near future huge amounts of LCDs will start coming back to recycling. As LCDs with hazardous mercury backlight lamps are used an appropriate recycling technology has to be implemented.IntroductionLiquid Crystal Displays (LCDs) are widely used in notebooks, organizers, mobile phones, pocket calculators, measuring and control instruments, electronic games, hand-held miniature TVs, audio-video equipment, large signboards, automotive displays and more and more also for PC monitors and TVs.According to a study from Stanford Resources (San Jose, California) the annual value of LCDproducts reached 35 billion EUR in 2002, about 30% of this within the European Union, representing a total area of 2,1 million m2 Liquid Crystal Displays. An annual increase rate of about 15% is estimated for the next years (up to 4,1 million m2 in 2005).As LCDs are already on the market for several years, larger quantities of the more than 2,5 billion LCDs are coming into their End-of-Life stage for treatment. In 2005 this figure will become even more dramatic - 40.000 tons of LCD-modules contained in 2 million tons of waste electrical and electronic equipment (WEEE) or about 30% of total WEEE within EU. An amount which is representing 400 million EUR costs for incineration.Currently the only method used to deal with redundant LCD units is incineration or landfill. Both are expensive and causes emissions into the atmosphere (global warming) respectively water contamination (Class II) and difficulties in biodegradation. Up to now there is no recycling solution for LC-Displays available.As a consequence European Commission requests the disassembly of LCDs with an area bigger than 100 cm2 in the Directive 2002/96/EC of the European Parliament and of the Council on Waste Electrical and Electronic Equipment (WEEE Directive) of February 13, 2003."

Jan 1, 2008

By K. Takahashi, G. Dodbiba, T. Fujita, N. Sato, S. Matsuo, K. Okaya

Different materials are used for manufacturing various parts of a cellular phone. Considering that a great number of mobile phones are being discarded every year, it is important to recover these materials and then recycle them in order to save resources. The primary objective of this work is therefore to find and suggest ways on how to recover various materials from discarded cellular phones for recycling. Much effort, for example, has been put in recovering and recycling tin oxide (ITO), a mixture of indium (III) oxide, (UI2O3) and tin(IV) oxide from the discarded liquid crystal displays (LCDs). Here we report a simple and cost-effective process, which includes a HC1 treatment process for altering the structure of the indium (III) compound into a chlorideinduced indium compound, in order to facilitate the vaporization of indium at a relatively low temperature. The experimental results indicated that 96.2 % of indium can be recovered from ITO, when the sample was heated at 973 K for 90 minutes. In addition, some thermodynamic calculations were also carried out in order to better understand the mechanism for chlorideinduced vaporization of indium.

Jan 1, 2011

By Uday Pal

In direct reduction processes for iron and steel making, significant amounts of Fe-C alloy droplets are generated and these remain suspended in relatively low FeO (around 5%) containing slags. Earlier workers have found that when the FeO content in the slag is <5%, the decarburization reaction becomes extremely slow (virtually ceases to occur) even though the alloy droplet contains a significant amount of carbons (2-3%). Understanding this rate controlling kinetic phenomena is crucial to designing an&apos; optimum direct steel making process. We studied decarburization of Fe-C particles by low FeO (<5%) containing CaO-SiO2A12O3 slags and found that by putting both the droplet and the slag in direct contact with an inert electronically conductive member that extends deep inside the slag bulk were able to quickly and completely decarburize the droplets. A detailed description and an explanation of the process will be presented.

Jan 1, 1995

By Robert J. Stevenson

The chemical variation of central North American lignite fly ash can be compared using the major and minor oxide analyses and the distribution pattern of the inter-grain chemistries of the individual fly ash have been used to illustrate the variations in bulk ,sample and individual grain chemistry. This information documents the chemical variability of the lignite fly ashes by geographic region. There is a direct relationship between grains rich in SiOa and AlaO, and in the NazO content of the grains in lignite derived fly ashes. There is also a direct relationship between grains rich in Ca0 and the MgO and SO, content of the grains in lignite derived fly ashes,. These variations are shown using CaO-SiO2-Al2O3 and CaO-Na2O-MgO ternary diagrams.

Jan 1, 1992

By R. Chiarizia

Third phase formation, i.e., the splitting of the organic phase in two layers, is a common feature observed, under conditions of high loading, for many solvent extraction systems of both analytical and industrial interest. Although this phenomenon has been investigated in a large number of works, a structural and physico-chemical description is still lacking. In this work, small-angle neutron scattering (SANS) data for the tri-n-butylphosphate (TBP)-n-octane,Th(NO3)4-HNO3 solvent extraction system have been interpreted using the Baxter model for hard-spheres with surface adhesion. The increase in scattering intensity in the low Q range, observed when increasing amounts of HNO3 and/or Th(NO3)4 are introduced into the organic phase, has been interpreted as arising from interactions between small reverse micelles containing three TBP molecules plus solutes in their polar core. This intermicellar attraction, under appropriate conditions, leads to third phase formation.

Jan 1, 2003

By T. Ranki-Kilpinen

In the flash smelting technique, developed by Outokumpu Oyj, off-gases with dust load are directed into the heat recovery boiler (HRB). As the temperature decreases, metallic sulphates become thermodynamically stable. Sulphation of oxidic particles initiates. The release of heat causes an increase in particle temperatures, and soft sulphated particles can stick to the heat transfer surfaces. Dust accretion may form and cause operational problems. The objectives of the project are to study sulphation reaction mechanisms and kinetics of flue- dust particles under HRB conditions, and get more information for the flue-dust treatment possibilities. The sulphation behaviour of synthetic Cu2O particles (37-53 pm) was studied using a fluid-bed reactor of laboratory scale. The experimental parameters in the latest campaign were oxygen and sulphur dioxide contents of 2.5-10 vol-% 02 and 40-60 vol-% SO2 respectively and temperatures of 600-660°C. Samples were examined microscopically (SEM+EDS) and chemical analysis were conducted. The sulphation rate was found to have a maximum at the certain temperature, which was dependent on the gas SO2 content. Regardless of the level of SO2, a rise in oxygen content promoted sulphate formation.

Jan 1, 2002

By C. J. Lewis

This presentation concerns calcium oxide-better known as high calcium quick lime High calcium quicklime is produced by calcining high calcium limestone, mostly in the many rotary kilns located throughout the United States and Canada. This paper presents suggestions on the handling of lime based on field experience. The subjects covered are chemical analyses, transporta¬tion, lime storage, lime slaking to form a water slurry of calcium hydroxide solids, slurry transportation, slurry viscosity, and scaling of lime slurries. It is hoped that the comments on the foregoing areas will be of use to those designing or operating lime systems.

Jan 1, 1992

By Akita Ito, Sumio Kato, Mikio Sugai, Shinichi Nakata

"Spark Plasma Sintering (SPS) is a newly developed method for the sintering of metal and ceramic powders, and completes their densification at low temperature and in short period. The SiC powder was synthesized from diatomite and graphite or carbon black by heating at 1 450°C for 1 hr in an argon atmosphere. The synthesized SiC powder was heated at 1500-1800°C, 50 MPa for 15-18 min by SPS. The relative density of sintered SiC body increased with the rise in the temperature. The oxidation of the surface of the SiC particle and impurities in SiC from diatomite greatly influenced the sintering promotion of SPS.IntroductionThe SiC has high hardness because of the covalent bonding, and is also excellent in thermal and chemical stability. However, it is difficult to obtain a dense SiC sintered body by the combustion heating-method. Therefore, the dense SiC bodies have been made by the use of additives and I or the hot pressing (HP) method.In this study, the SiC powder was synthesized by using diatomite of natural products and graphite, and carbon black of reagent as raw materials, and the relationship between the properties of SiC powders prepared at various synthetic conditions and the density of sintered body by SPS was examined."

Jan 1, 2000

By R. D. MacDonald

The papers presented in this chapter cover a wide range of hydrometallurgical topics and might be considered to be unrelated to each other. All of the authors, however, utilized the basic methods of process mineralogy to characterize the reactants in their experiments and the products produced. The wide range of research topics which can be pursued successfully by the use of the methods of process mineralogy is a matter of interest in itself. One might speculate that the methods could be even more widely applied if only their utility were better recognized. These methods for characterizing reactants and products include principally x-ray diffraction, optical micros-copy, wet chemical analyses, instrumental chemical analyses, high intensity magnetic separation, micro-scale gravity separation, differential thermal analysis, micro-hardness testing, and judicious use of the sledgehammer and cold chisel. It is perhaps not by coincidence that most of the papers in this chapter were prepared not by mineralogists, but by hydrometallurgists, who are recognizing the importance of thinking in terms of mineral phases, and not just assays! It appears that the gap between process mineralogy and the mineral industry is closing, and that future AIME sessions promise to become established forums where mutual discussion of such topics as metallurgical "troubleshooting" and process design may become commonplace between plant engineer and process mineralogist.

Jan 1, 1981