Search Documents

By Mariana H. Staia

Thermodynamic calculations based on the free energy minimization method were performed for the system Ti-Fe-Mn-0-C1-C in order to evaluate the chemistry associated with the chlorination of an ilmenitic concentrate using CCl4. In the calculations various weight ratios of FeTi03/ CC14, a , were considered, which varied between 0.32 to 0.98 at temperatures ranging from 673 K to 1273 K , at atmospheric pressure. The results obtained indicated that the operating conditions for a process in a packed bed reactor, which implies the chlorination of both Fe and Ti, are 0.39 < a < .49 at T 1173 K.

Jan 1, 1993

By Robert W. Bartlett, Keith A. Prisbrey

"Natural biooxidation of shallow, refractory ore heaps, relying on gaseous oxygen diffusion from the heap surface is attractive because of its simplicity and potential low cost, especially without using a lined pad, which is possible if percolation of leachate through the heap is avoided. In this case, the excess oxidation enthalpy must be removed by water evaporation from within the wet ore heap, and the rising water vapor flux within it will impede the downward oxygen flux. An analysis of this process shows that for typical values of pyrite grades and limited temperature increases in the ore heap, the oxidation rate and penetration into the heap is reduced to values between about 30 percent and 50 percent of those obtained when leachate percolation occurs and water evaporation is not a significant mechanism of heat removal.IntroductionHeap biooxidation of refractory gold ores, needed as a pretreatment step to liberate the gold for subsequent extraction by leaching, requires large amounts of oxygen for the normal amounts of sulfide minerals that are typically present, one to two percent pyrite and/or arsenopyrite.The importance and potential limitations of oxygen transport into commercial ore heaps, which are much larger than encountered with column tests of ore and with pilot heaps, has been recognized111 • Commercial ore heaps using radial stacking conveyors are typically about nine meters high and may be 100 meters or more in lateral dimension. Three oxygen transport mechanisms have been identified and analyzed: ( 1) natural convection, which arises from an increase in buoyancy caused by the temperature rise and gas composition changes associated with the exothermic oxidation of the sulfide minerals within the ore heap, (2) forced air ventilation, using low pressure fans and air distribution pipes within the heap, and (3) diffusion of oxygen in the gas-filled void spaces within the ore heap driven by the oxygen concentration gradient from the surface of the heap to the mineral oxidation loci within it."

Jan 1, 1997

By Anil Saigal, Jr. Fuller, Said Jahanmir

"All-ceramic crowns, including glass-infiltrated spinel composites, are coming into widespread use because of their superior aesthetics and chemical inertness. This study investigates the residual stresses that are developed in these composites as a result of cool down from the glass-infiltration temperature to room temperature due to slight mismatch in the coefficients of thermal expansion and its effect on the mechanical behavior of these composites. Two-dimensional finite element simulations were performed using an object oriented finite element program OOF. The OOF program is a combination of two programs. The first program, PPM200F, is designed to read an image file such as a micrograph. The individual pixels that constitute the micrograph may be collected into groups and their material properties assigned. PPM200F is then used to create the finite element model/mesh that OOF then reads. The average residual stresses are found to be tensile in the spinel matrix and compressive in the infiltrated-glass. There is large variation in residual stresses and strains from location to location with presence of locations at which the glass is under tensile stress. The crack initiation and initial propagation in glass-spinel composites is at the glass-spinel interface in both the glass and the spinel. The presence of residual stresses can lead to lower crack initiation stresses and degrade the mechanical properties of the composites.IntroductionGlass-infiltrated spinel ceramics are in clinical use as core materials in all-ceramic crowns and as inlays and onlays (1-3). Advantages of ceramic composites include near net-shape forming with high strength in the infiltrated state. Besides, spinel is quite translucent and may potentially be used without a veneer. However, these ceramic composites are subject to damage accumulation from repeat oral contact loading and often fail after a few years of use (4). This paper examines the residual stresses that are developed in these composites, after cooldown from the glass infiltration temperature to room temperature, due to the slight mismatch in the coefficients of the thermal expansion of the two phases."

Jan 1, 2001

By Sergey Komarov, Manuela Diaz, Sano. Masamichi

"Mixing time, bubble behavior and absorption rate of gas injected into a liquid bath through rotary L-shaped lances have been studied by cold models with an effort to improve refining characteristics of metallurgical processes. Two kinds of the rotary lances were tested, namely the single-hole lance and the multi-hole lance. The effects of gas flow rate, bath depth and rotation speed were examined.It is found that when gas is injected through the rotary lances, the mixing intensity and the gas absorption rate are larger than that for the gas injection through stationary lances. The effect of rotation speed decreases as the bath depth and the gas flow rate increase.The multi-hole lance produces much smaller bubbles, which lead to an increase in the volumetric mass transfer coefficient by 3-4 times as compared with the single-hole lance. However, the effect of rotation speed is smaller for the multi-hole lance. The obtained results are explained in terms of the bubble coalescence and fragmentation, the rate of which depends on the departure bubble size and the power supplied to the liquid bath.IntroductionIn recent years, there has been a growing interest in the development of gas injector for metallurgical processes. The majority of the previous work was focused on modification to the injector design to improve mixing and to increase the of chemical reaction rate. These two goals can not be necessarily achieved by the same way. Bottom nozzles and stationary immersed top lances, which have been widely applied to steelmaking processes, are effective for the bath mixing, but have a limit to decrease in the bubble size. This results from a vigorous coalescence occurring between the bubbles when they rise in the molten bath as a bubble swarm.One of the ways to ensure the small bubble size and the effective bath stirring is the gas purging through rotary injectors. A number of studies have been undertaken to improve the refining characteristics by using rotary injectors. All of them are related to aluminum refining. The SNIF equipment (The Spinning Nozzle Inert Flotation) has significantly improved the quality of aluminum products at National Luxemburg Aluminum [1]. Rotary injectors made in the form of a disc have been applied to the Alcoa 622 [2] and the GBF processes [3]. A study of the gas injection by a rotary impeller has been carried out by C. Leroy and G. Pignacelt [4]. All researchers note the significant improvement in removal of sodium, calcium, hydrogen and non-metallic inclusion."

Jan 1, 1996

By Z. Sadowski

The influence of organic acids simple salts and A. niger saccharose and molasses worts on sodium oleate adsorption on the salt-type mineral surfaces has been studied. It was found that salts of organic acids had an effect on the sodium oleate adsorption on barite calcite and magnesite. The collector adsorption on the barite and calcite surfaces decreased under the influence of investigated worts. Experimental data suggest that the biomodification of salt-type mineral surfaces can be used for the selective separation of these minerals.

Jan 1, 1991

By A. De, J. S. Zuback, T. Mukherjee, T. DebRoy

For successful commercial applications of additive manufacturing, metallic parts need to be defect free, structurally sound and reliable. However, additively manufactured metallic parts are susceptible to distortion, lack of fusion defects and compositional changes. Methods to measure susceptibilities of various alloys to these defects are needed but not currently available. Here we show that the necessary theories can be developed based on a well-tested numerical heat transfer and fluid flow model and decades of research in the field of welding. The proposed theories are validated with experimental results reported in the literature.

Jan 1, 2016

By Enrique Posada

"The Valle de Aburrá area, corresponds to the city of Medellín and neighboring municipalities, with more than 3 million people. The area generates a sizable amount of solid waste, which has been taken to landfills for the last 20 years. This paper proposes a model for public policy making which considers the cost and benefit of different alternatives to handle the wastes in the coming 20 years. Combinations of several alternatives: Recycling, waste reduction, waste separation, incineration, land filling with lixiviate treating and gas energy recovery, and organic waste composting are considered and modeled and the results presented as a contribution for a more rational approach to policy making than the one currently being employed.IntroductionThe author, working for INDISA S.A., acted as a consultant for the direction of planning of the Empresas Varias de Medellín in 2004. This entity has the responsibility for the handling of the solid wastes of the city of Medellín and some of the neighboring municipalities. At the present time more the 700.000 annual tons of waste are taken to the site of La Pradera, located in very rainy location (3.000 mm of precipitation per year), with complex in topography and very far away from the sources of the waste. During the work the author detected important problems that should be addressed, as follows:Lack of adequate technical administration and resources. The entity did not count with sufficient human resources to focus on the appropriate technical handling of the solid waste. The organization worked mostly with independent contractors, lacking enough coherence and integration. The internal workload was too large for the few people who had technical responsibility and this gave rise to attention problems. It is important to have clear technical procedures, technical know how and human resources, continuity in the activities. It is important to have a clear capacity to plan, to study, to make tests and monitoring, to pursuit and develop ideas, to optimize the processes and to introduce changes, to respond to environmental authorities, to the communities and to mass media and to handle the contractors. All this was basically lacking. In the case of the handling of the sanitary filling of La Pradera, for example, although the people in charge were very able and dedicated, the magnitude of the task was too large and the resources they had were insufficient. As a result, the site had at the time of the study, problems with thousands of vultures, lack of immediate cover up for the waste, uncontrolled leaching, the area being dirty and little attractive, despite being called a park."

Jan 1, 2008

By Henry Hu, Alfred Yu

"A numerical model has been developed to simulate heat and mass transfer phenomena occurring during a novel magnesium reduction process-the vertical retort technology. The model was based on the control - volume finite difference approach. Simulations were run to determine the effect of various processing parameters on magnesium reduction cycle time. The model predicted temperature distributions, heating curves, recovery ratio of magnesium, and total process times. The predictions were used to optimize the magnesium reduction process including dimensions of the retort, geometries of the reactant compounds, and productivities. The results indicate that the implementation of the optimized processing parameters significantly decreases the reduction time, and consequently increases the production rate as well as lowers the energy consumption.IntroductionMagnesium consumption has been growing considerably in the past decade [1]. Of the total magnesium production, 30% is produced by the thermal reduction (Pidgeon) process, and it is anticipated to be still the main technology for producing magnesium in future [2]. One of the advantages of the Pidgeon process is that it is capable of producing high purity magnesium demanded by both the automotive and aerospace industries. However, the inefficiency of heat and mass transfer taking place in the horizontal Pidgeon reduction process results in low productivity, high energy consumption, labor-intensive operation, large floor space and high capital investment. This limits the production scale of a horizontal Pidgeon reduction process [3].Vertical reduction processTo overcome the shortcomings of the horizontal magnesium reduction process, a novel vertical magnesium reduction process [3] for large-scale production has been developed, in which heat and mass transfer in the retort is enhanced. The new process shortens reduction time, reduces energy consumption and increases productivity. The vertical reduction system is comprised of a vertically-placed retort, a heating furnace and a vacuum system. A section of the vertical retort is illustrated in Figure 1. Since the retort is set vertically, instead of horizontally, the entire procedure of loading the reactants material in the new process is different from the one for the horizontal reduction process."

Jan 1, 2001

By Kongfang Feng, Fei Ruan, Zhiyu Liu, Jieyu Zhang, Xin Hong, Shaobo Zheng, Jixu Wang, Jinyin Xie

"Mixing phenomena in smelting reduction furnaces with asymmetric side blowing were studied in this paper. Mixing phenomena in a smelting reduction furnace was represented as the mixing time by electrical conductivity measurements. Experiments were performed in a water model under various operating conditions to determine the effects of horizontal angle, radial angle, inserting depth, flow rate of the upper and the lower side nozzle, the included angle between the upper side nozzle, and the lower side nozzle on mixing phenomena in smelting reduction furnace. Comparing mixing time and mixing phenomena, the optimal conditions were obtained for an asymmetric side blowing process.IntroductionIn recent years, many countries have put forward development strategies for saving resources and environment-friendly, the development of various industries had to face its influence for resources and the environment .As we all know, the steel industry is a pillar industry of the global economy, in which ironmaking is an important part of it. In the modern ironmaking process, the blast furnace is regarded as the most important equipment and tool. But with the increasing scarcity of metallurgical coke resources and considering the environmental impact of such processes, metallurgists proposed the concept of smelting reduction. Smelting reduction processes to produce hot metal from iron ore and coal were being developed as a possible alternative to the traditional blast furnace. At present, a number of smelting reduction processes had been developed all over the world, they were mainly included COREX, HISMELT, FINEX, DIOS, etc."

Jan 1, 2012

By Jae-Ho. Lee

Mercury is a toxic contaminant encountered in the extraction of gold from mercury-containing ores. It is found in the leach solution of CIP circuits and in the cathodes of the electrolyte cells used to electrodeposit the gold. The research conducted has examined the potential for selective removal of mercury from synthetic Au-Hg-CN electrolytes containing only gold, only mercury, and both gold and mercury. Cyclic voltammograms were obtained for mercury- coated copper electrodes with these cyanide electrolytes. Exchange current densities were determined from the voltammograms in the low overpotential region. Laboratory scale batch- electrolysis at constant current was also conducted for the electrolytes containing only mercury and both mercury and gold, at 20 and 50°C and from which the kinetic behavior associated with the process was analyzed. The surface of cathode before and after electrolysis was also characterized and a copper mercury intermetallic (CyHg,) was identified. Gold codeposited with mercury during the later stages of electrolysis. The results of this work corroborate that the mercury-amalgam copper electrode offers a viable electrochemical technique for the selective removal of mercury, however a high-surface-area cathode-cell would have to be utilized to provide for the desired selectivity.

Jan 1, 1994

By Kazusuke Sato, Takahiro Uno, Koji Hoshino

"A novel Ni coating technique of Ni(OH)2 powders was developed to improve the positive-electrode performance· of the Ni-MH batteries. It was found out that Ni(OH)2 powder was reduced by N2H4 without any catalysts in an alkaline - solution at high temperatures. In result of observation of pH and potential changes in the solution during the reaction, it was found that the reduced species was HNio2- ion dissociated from Ni(OH)2 in the alkaline solution. The molar fraction of reduced Ni of the Ni(OH)2 was increased in proportion to the amount of added N2H4. At the small Ni fraction, a porous Ni layer was formed on the surface of Ni(OH)2 powder. Open cell tests were carried out with the paste type electrodes made of either the Ni coated Ni(OH)2 powder or non-coat powder, and cell performances were compared. In result, it was found that the Ni coating technique is effective on improvement in the utilization of Ni(OH); as a positive-electrode active material under high current densities.IntroductionNi-MH rechargeable battery is generally used for the power source of portable machines and electric vehicles because of its good performance at high energy density and. long term cyclical life as well as cleanness and good safety. Cell component materials have been improved respectively, and as concerns ·the positive-electrode reducing 'the internal resistance is a principal problem to improve the discharging performance at higher current densities.In recent years, improved Ni(OH)2 powders coated with conductive materials as NI. or CoOOH have been developed for the· positive-electrode active materials in order to· reduce the internal resistance of the electrode1)· 2) The Ni coated Ni(OH)2, however, is costly because it is fabricated by .the -non-electrode plate technique which needs a expensive precious ·metal catalyst as PdC12We found that Ni(OH)2 powder was reduced by N2H4 without any cryatalysts in an alkaline solution at high temperatures. After the treatment, Ni(OH)2 powder become gray color like Ni powder from light-green color; and. turned into a magnetic. In this study, the mechanism of the -reducing reaction was investigated to apply the reactions .to a novel Ni coating technique of Ni(OH)2 powders, · and the performance of the Ni coated Ni(OH)2 powder obtained by the reducing process was evaluated as an -positive-electrode active material of Ni-MH batteries."

Jan 1, 2000

By Wenbo Luo, Jilai Xue, Tiepeng Li, Jun Zhu

Sodium silicate solutions for producing silica have been ultrasound treated to enhance the precipitation process in laboratory scale. Higher precipitation rate was found with ultrasound treated solutions than those without ultrasound. The obtained SiO2 powder products were characterized using XRD, SEM, BET and laser particle size analyzer. The particle size distribution and the specific surface area of the powder products varied with the power input level and the processing time of the ultrasonic treatment. The results indicate that the efficiency of the precipitation process can be improved optimally when the ultrasound is conducted into the solutions before the nucleation stage.

Jan 1, 2015

By Adam Gesing, Paul Marchwica, Jerry Sokolowski, Sharon Lackie

"Often referred to as SEM-EDX, energy-dispersive spectroscopic analysis of characteristic fluorescence x-ray is a standard technique for semi-quantitative elemental composition analysis in scanning electron microscopy. It is quick and extremely useful for identification of phases in the sample microstructure, as long as the constituents are significantly larger than the probe volume from which the fluorescence x-rays originate. The probe volume ranges from a few to several microns, depending on the electron beam spot size and the acceleration voltage. We report on a new variant of an EDX technique developed to overcome this limitation and allow quantitative elemental analysis of smaller phase constituents, down to a size of several nanometers. This variant involves the calculation of compositions of individual phases from multiple analyses of areas containing phases of interest. This significantly increases the usefulness of EDX for quantitative analysis of new nano-structured materials.IntroductionIn any elemental micro-analytical method, the sample material is illuminated by a probe beam that excites an interaction volume of a sample to emit a characteristic signal. This signal in turn interacts with the sample material through absorption and fluorescence mechanisms before a portion of it is collected by a suitable detector and analyzed for elemental composition. The spatial resolution of the method depends on the minimum interaction volume between the probe beam and the sample material.Laser light beams can be tightly focused to a spot size limited by the photon wavelength and can be used to sample the surface of any material. In micro-LIBS (laser-induced plasma spectroscopy) a focused laser beam ablates and vaporizes a small volume of material from the sample surface, creating a plasma spark. Spectral analysis of the light emission from the plasma spark allows the semi-quantitative determination of the elemental composition of the material removed from the sample surface. The smallest reproducible craters achieved are ~ 3mm in diameter and a few nanometers in depth. [l]Particle probe beams of ions or electrons can be focused to a diameter of a few nanometers at the point of impact on the sample. Ions sputter the sample atoms from the point of impact, and the sputtered ionized material is analyzed by mass spectroscopy in a secondary ion mass spectrometer (SIMS). [2] This gives SIMS resolution in a nanometer range. SIMS equipment, however, is expensive and not readily available."

Jan 1, 2013

By Jun Zhu, Jilai Xuel, Tao Li

"Coal gangue is industrial waste containing Al2O3 and SiO2 with great recycling and reuse values. This work is aimed at extracting Al2O3 content in the coal gangue by a process of carbonthermal reduction - alkaline leaching. The Al2O3 and SiO2 contents first became a mixture of SiC and Al2O3 in the process of carbonthermal reduction, and then Al2O3 was separated by leaching in NaOH solution, thus producing the sodium aluminate solution for Al(OH)3 precipitation. The products generated at various stages in the process were inspected using XRD and chemical analysis. The effects of parameters such as reduction temperature, carbon ratio, NaOH concentration, leaching time, leaching temperature, stirring speed, etc were investigated in details.IntroductionCoal gangue is an industrial residue resulted from the process of coal mining and washing, accounting for 100 - 150 kg with 1 ton raw coal mined. The existence of coal gangue in large quantities has become a serious problem for environment pollution. On the other hand, the chemical compositions of coal gangue are Si02 and Ah03 primarily. In China, the accumulation storage capacity of Ah03 in coal gangue is not less than 600 million ton at a rough estimate, which should be considered as an abundant second resource [1]. If the alumina can be recycling and reused effectively from coal gangue, it will not only reduce the imperilments caused by coal gangue, but also yield good economic returns.Generally, the processes of extracting Al2O3 from coal gangue can be divided into acid leaching (vitriol or hydrochloric acid) and alkaline leaching (mostly NaOH) [2]. The acid leaching processes have many problems, such as lower leaching ratio, corroding the equipments, recycling the spent acid hardly, etc. The primary matter of alkaline leaching process is silica dissolving with alumina, which brings perplexing desilication process, alumina loss seriously and higher energy consumption."

Jan 1, 2011

By R. L. Nyirenda

The use of ammoniacal ammonium carbonate (AAC) leaching for the treatment of carbon steelmaking EAF dust has been investigated on a laboratory scale. The experiments have been conducted on dust samples obtained from three European steelmaking companies. As received, the dusts were found to be toxic when tested according to current EPA toxicity testing procedures. Toxicity was on account of the leachability of one or more of the following elements: Ag, Hg, Pb, and Cd. Leaching experiments with concentrated AAC solution at 40 " C showed that zinc oxide present in the three dust samples, 60-80% of the total contained zinc, was rapidly solubilized. Data on the dissolution characteristics of Cd, Fe, Pb, Mg, and Mn are also presented. Toxicity tests conducted on residues of the leaching experiments found these to have leachates below past and current EPA toxicity threshold limits.

Jan 1, 1993

By Ibrahim Yusufoglu, Cem Kahruman, Mert Zoraga

In this study, a strontium sulfate mineral (celestite) was converted to strontium oxalate in solutions containing ammonium oxalate as a reactant. The experiments were carried out under isothermal conditions. The effects of stirring speed, ammonium oxalate concentration, particle size and temperature on the conversion rate were investigated. During the conversion process, definite volumes of solutions were taken from the reactor after different reaction times for the determination of sulfate ions using ICPOES. Fractional conversions of strontium sulfate were determined at different times and fractional conversion vs time diagrams were generated. It was found that the conversion of strontium sulfate was increased by increasing the ammonium oxalate concentration and temperature in addition to decreasing the particle size. The effect of stirring speed was negligible on the reaction rate. It was observed that above 328 K, a protective layer of strontium oxalate was formed on the strontium sulfate particles. X-ray Powder Diffraction technique was used for characterization of solid substances.

Jan 1, 2014

By M. Boussuge, M. -D. Dupuits, A. Piant

This paper summarises a part of the work that has been essentially carried out at the Ecole des Mines de Paris in the framework of an Eureka European programme funded by the French Ministry of Industry, in partnership with Metaleurop and Carborundum (subsidiary of Saint Gobain). It deals with the measurement of different properties (density, thermal linear expansion, elastic modulus, strength) of a SiC-based refractory constituting the trays that are used in the refining columns in the New Jersey zinc distillation process, especially in the boiling section. These parameters have been investigated to check the homogeneity of the asreceived trays as well as to estimate the influence of ageing of the material under operating conditions. With this aim, specimens have been sampled in used trays having more than two years of operation. The as-received trays exhibited a good homogeneity, the strength being slightly lower in the direction in which they are compacted. Despite microstructural changes, most of the properties measured at room temperature are not significantly affected by ageing. High temperature tests involved thermal treated under vacuum to remove metallic zinc before testing at high temperature. An increase in temperature, as well as ageing, induces a decrease in the elastic modulus and strength.

Jan 1, 2000

By Thomas J. Keefe, O&apos

The effects of cobalt, B-naphthol, glue and antimony on the polarization behavior of zinc sulfate electrolyte were investigated. It was found that B-naphthol was beneficial in reducing the detrimental effects of cobalt while antimony and excess glue were each harmful. Since the nu cl eat ion over potential was insensiti1ve to coba1t, other regions of the polarization curve were used to indicate electrolyte balance. The low? current density area occurring in the reverse or anodic sweep direction was? often an indicator when an ?unstable condition existed. The two parameters evaluated were the degree of inflection in the polarization curve in the low current density region during scanning and the rate of current rise observed when the sample was potentiostated at -0.781 Volts (SHE). Using this technique, a two-additive system was shown to be desirable to control cobalt and antimony containing electrolytes. The structure of the deposits was examined using scanning electron microscope techniques.

Jan 1, 1985

By William E. Frazier

The presence of minute amounts of sulfur (10ppm) in nickel-base superalloys has been associated with reduced oxidation resistance and the premature spallation of protective coatings. Removal of sulfur by annealing these alloys in a hydrogen atmosphere has been successfully attempted by several researchers. This paper examines the fundamental thermodynamics and kinetics governing hydrogen desulfurization of elemental nickel. Limiting conditions for successful desulfurization are delineated. Assuming that the diffusion of sulfur is the rate limiting process of desulfurization, the effectiveness as well as time associated with hydrogen desulfurization is explored.

Jan 1, 1994

By Cesar O. Gomez

A procedure has been developed for mounting at random particles of mineral samples to be characterized using image analysis. The procedure is based on the generation of a random distribution of sample particles in particles of a diluent material. and the embedding of this particle mixture in an epoxy resin without disturbing the initial distribution. Two materials with atomic number similar to that of the epoxy resin were successfully used as diluents: activated charcoal and graphite. The proportion of diluent material to be mixed with the sample to have a large number of mineral particles in the field of view while keeping the occurrence of touching particles at an acceptable level was determined empirically. The randomization achieved with the procedure developed in this work was tested using as samples known mixtures of silica and pyrite particles of the same sieve class. The agreement obtained between the mass ratio of minerals used in the preparation of a particular specimen and that resulting from image analysis demonstrates that the procedure developed is successful in producing a specimen where the embedded particles are randomly distributed.

Jan 1, 1988