Search Documents

By Soumendra Basu, Uday Pal, Yang Yu, Srikanth Gopalan, Karl Ludwig, Deniz Cetin, Jacob Davis

"A limiting factor for Solid Oxide Fuel Cell (SOFC) performance is the oxygen reduction reaction (ORR) at the cathode surface. Changes in the surface composition and structure on annealing at 800°C has been studied, since these can influence the ORR. Idealized single crystals of cathode materials La0.8Sr0.2MnO3 (LSM) and La1-xSrxCoyFe1-yO3 (LSCF) were grown as heteroepitaxial thin films on lattice matched single crystal substrates. Changes upon heating the films to operating temperature and pressures were characterized using various synchrotron x-ray techniques. Total Reflection X-ray Fluorescence (TXRF) measurements, which probe compositional changes, were made at high temperature in real time. The LSM surfaces were found to develop manganese enrichment when heated. Highly strontium doped LSCF were found to develop strontium-rich surfaces. HArd X-ray PhotoElectron Spectroscopy (HAXPES) was used to investigate the electronic structure of the materials. Highly strontium doped LSCF precipitates a surface strontium phase that contains both oxide and carbonate contributions.IntroductionSolid oxide fuel cells (SOFCs) are chemical to electrical energy conversion devices that could potentially reshape how energy demands are fulfilled. SOFCs have a potential efficiency over 70%, fuel flexibility, low emissions, and low degradation over long time scales. Commonly, SOFCs are operated at high temperatures (above 800°C). At these temperatures expensive housing is needed to contain an operating stack as well as coatings to contain the oxidation of the metallic interconnects. Lowering the temperature of an operating device would allow for more conventional materials to be used, thus lowering overall cost. Understanding the reaction kinetics of the oxygen reduction reaction at the surface of the cathode is vital to designing a system that will perform well at lower temperatures. A commercialization goal is to reduce operating temperatures without sacrificing performance.In order to exploit the advantages of SOFCs, an understanding is needed of the surface chemical states of cations on the surface of the cathode and how this relates to the oxygen reduction reaction (ORR):"

Jan 1, 2014

By H. H. Law

Large amounts of waste material in the form of flue dust are generated in the operation of copper smelter furnaces. As a result of increasingly stringent disposal, it has become important to develop methods for treating such metallurgical wastes to extract metals and convert them into salable products. A two-step closed-loop hydrometallurgical process, has been developed: (1) extraction with sulfuric acid removes about 90% of zinc and decreases the dust volume by 50%; (2) extraction with hydrochloric acid dissolves the lead and further decrease the dust volume by 75%. A process scheme for generating salable products is proposed.

Jan 1, 1992

By Mieke Campforts

The usefulness of the water-cooled probe technique to experimentally study slag solidification and freeze lining formation in pyrometallurgical reactors is evaluated. With this technique a layer of solidified slag is formed on a water-cooled probe that is submerged into a liquid slag bath. The influence of the submergence time and the heat input is examined. The solidified layers are analyzed with light microscopy, electron microscopy, electron probe micro-analysis and X-ray diffraction. Thermodynamic software is used to interpret the solidification microstructure. The results demonstrate that the technique is useful to understand freeze lining formation.

Jan 1, 2006

By M. P. Bohrer

A closed-loop hydrometallurgical process has been developed for treatment of smelter flue dust generated by copper recycling. The process is a semi-continuous operation in which zinc, iron, and copper are first extracted from the dust with a sulfuric acid solution. The lead and precious metals, initially present in the dust, remain as solids and can be recycled to the copper smelting furnace. Cementation with iron and zinc metal purifies the zinc and iron-rich liquid stream prior to spray drying. The spray-dried product, consisting of a mixture of zinc sulfate monohydrate and iron sulfate monohydrate, is a desirable micronutrient additive for use in animal feeds. Treatment of the smelter flue dust in this manner will generate a positive return on investment, as well as mitigate a potential environmental liability.

Jan 1, 1992

By Susanne Pignolet-Brandom

Reflected light microscopy scanning electron microscope energy dispersive spectroscopic analysis and backscatter electron image and electron microprobe chemical analysis have been used to study lead sinter and lead blast furnace slag. These studies provide invaluable information on the phases present their intergrowths, and their chemical composition. Such information increases the understanding of the nature of pyrometallurgical processes and the behavior of minor elements during these metallurgical processes.

Jan 1, 1987

By Seshadri Seetharuman

The present paper summarises a series of measurements of the interaction parameter of oxygen in liquid copper with respect to a third element, e(M)o, where M is Mn, Zn, As, Se or Te which are common impurities in the liquid metal. The technique employed was the solid electrolyte galvanic cell method. The cell used may be represented as Pt, W or cermet / Cu-O-M // ZrO2 - CaO // AO, A /PT where AO/A represents a suitable oxide/metal reference. The measurements indicate that Mn and Zn interact very strongly with oxygen in liquid copper while, in the case of arsenic the interaction parameter is nearly zero. The behaviour of the elements Se and Te is unique with respect to oxygen interactions in copper bath. At oxygen levels, xo= 10-4 ? 10-5, the apparent interaction parameters are negative, comparable to that for sulphur. On the other hand, at lower oxygen levels, the results indicate that the interaction parameter values are positive. The results are discussed in the light of some of the theoretical models for solute interactions in liquid metals.

Jan 1, 1993

By Christian Redl

"The Lattice Boltzmann Method (LBM) solves fluid dynamics problems based on a discrete mesoscopic approach. It is based on the Lattice Boltzmann equation which is a special discretisation of the continuous Boltzmann equation. Its principle advantage is that it can handle complex physical phenomena (like interaction between different components and surface effects), complicated boundary and initial conditions very well, free from many gridding and stability constraints that plague conventional numerical methods used for fluid flow simulations. Complex structures like porous media can be resolved directly. The LBM algorithm has a simple structure and acts locally, which is favourable for parallel computing. Its potential for metallurgical process simulation is demonstrated in the present study which is concerned with the simulation of the fluid flow in a copper winning electrolysis cell. The electrolyte is modelled as the carrier fluid and the oxygen is considered via a so called active scalar equation. The modelling of buoancy, momentum exchange and the free surface requires special effort. The results of the simulation are validated against experimental data obtained by Laser-Doppler-Anemometry. Despite the simplifications made, good agreement between the simulation and the experiments was found.IntroductionThe hydrodynamics in an electrometallurgical cell is a complex, highly non-linear phenomenon. It includes the simulation of a two component system with high density ratio, gravity driven flow and a free surface. A general solution to this problem is currently unknown.The flow field is a result of the combination of various hydrodynamic effects [18]. Metal deposition at the cathode yields in a decrease in the ion concentration, which reduces the density of the electrolyte. At the anode molecular oxygen is formed as a consequence of the oxidation of water molecules. The oxygen is solved in the electrolyte and again the electrolyte density is decreased. Both effects lead to a free upwards directed convective flow, refered to as natural convection."

Jan 1, 2001

By Hirofumi Tai, Masafumi Morishita, Toshiya Miyake

"In order to prevent corner cracks on cast steel slab and bloom, solidification delay at the corners should be controlled at the proper level. For this purpose, controlling the heat flux from the molten steel to the solidified shell at corners is essential. In this paper, optimization of the submerged nozzle was studied based on flow and solidification analysis.First, for the slab caster, the submerged nozzle shape was optimized. The improved nozzle was tested in actual casting and completely succeeded in preventing corner cracks. It was clearly demonstrated that the solidification delay and the corner cracks were strongly affected by the spouting stream from the submerged nozzle.For the bloom caster, on the other hand, the setting angle of the nozzle was optimized. Numerical simulations demonstrated that the spouting stream from the nozzle causes solidification delay, impinging at the corners under electromagnetic stirring conditions. Optimization of the setting angle of the nozzle is a possible means to reduce the solidification delay at the corners for the bloom caster.Related to the numerical analysis of flow and solidification, the effect of the critical solid fraction at the tip of the dendrite structure on the solidification under electromagnetic stirring conditions was studied."

Jan 1, 1999

By G. A. Brooks, R. W. Matusewicz, Nazmul Huda

"A computational fluid dynamic (CFD) model of a conventional tuyere blown slag fuming furnace has been developed in Eulerian multiphase flow approach. The model was developed by coupling CFD with kinetics equations developed by Richards et al. for zinc fuming furnaces. The model integrates submerged coal combustion and chemical reactions with the heat, mass and momentum interfacial interaction between the phases in the system. The model predicts the velocity, temperature field of the molten slag bath, generated turbulence, vortex and coal utilization behavior from the slag bath. The highest coal penetration distance was found to be at l/L = 0.2, where / is the distance from the tuyere tip and L is the total length (2.44m) of the modeled furnace. The model also predicts that 10% of the injected coal bypasses the tuyere gas stream un-combusted and carried to the free surface, which contributes to ZnO reduction near the free surface.IntroductionSignificant metal values are often discarded with slag in the form of metal oxide produced by the smelting industries. These metal values can be recovered from the slag by proper treatment. Zinc slag fuming is such a process, where a reductant source (usually coal) is injected in the molten slag bath to reduce dissolved ZnO from the bath into metallic zinc vapour. The process can be carried out in either conventional tuyere blown furnace or top submerged lance (TSL) smelting furnace. Conventional slag fuming processes are carried out on batch basis in a rectangular tuyere blown furnace. Approximately 50 tonnes of charge (either molten slag or solid slag) is fed to the furnace at the beginning of each fuming cycle. Two opposing sets of submerged tuyeres are employed to inject air and pulverized coal into the molten slag bath to carry out combustion and reducing reactions."

Jan 1, 2012

By Santo Ranieri

We will briefly review the nickel market in 2003 and look forward to the supply demand balance for the next few years focusing in on the key factors influencing future price dynamics. On the supply side we will examine slated brownfield and greenfield expansions including the Norilsk factor and the small to mid-range 'supply creep'. We will also review the cost side of the industry and what to expect going forward. On the demand side, we will discuss the stainless steel and non-stainless demand, the China factor and the stainless steel scrap supply cycle. We will conclude by pinpinting where the market is on the current price cycle, and where we believe the mid-term direction is headed.

Jan 1, 2004

By Chao Lian, Hongxu Li, Hao Bai, Wei Wei

"Application of high-emissivity coating on inner walls in industrial furnaces increases the furnace thermal efficiency. The coating with high emissivity strengthens radiation heat transfer in the furnace, however, according to Wien's displacement law and Planck's radiation law, under heating temperature, the wavelengths of the radiation transfer are mostly between 1-5 µm, implying that increasing emissivity of the coating in near infrared band is more effective for higher thermal efficiency. In this paper, a new CuO-ZnO-based coating material sintered at 1600K was developed. The emissivity of the samples were measured and the result shows that, in near-infrared band, the emissivity of the sample reaches 0.98 at 773K with 13at.% of CuO doped in ZnO. In addition, the effects of CuO doping and use temperature on emissivity were also discussed. Furthermore, crystallization behaviors of ZnO-CuO sintering were investigated by DTA,XRD and SEM-EDS etc., which offered information for possible optimal design of the material.1. IntroductionIndustrial furnaces are widely used in various industrial heating. For example, the metal smelting furnace, ore sintering furnace in metallurgical industry; the distillation furnace, cracking furnace in petroleum industry etc,. The research on efficient energy saving technology has important significance. High emissivity coatings are widely used in many high temperature applications to effectively transfer the heat by radiation [ 1]. The theoretical calculation and experimental studies have shown that, coated high emissivity coating in the heating surface is an effective method to enlarge the infrared radiation power [2].At present, the infrared high emissivity coating has been widely used in China, and have been achieved remarkable energy saving effect. According to Wien' s displacement law and Planck' slaw, most energy of the black body at high temperature is radiated in the wavelength range of l-5µm; however it happens that many materials have the low emissivity within this range. Thus, it is important to improve the near-infrared band emissivity of materials [3]."

Jan 1, 2013

By M. Suzuki, M. Dobashi, M. Kahata, T. Yoshida

Almost 30% of steel in Japan is produced by electric arc furnace (EAF) treatment of iron scrap. EAF dust includes approximately 20 wt % of Zn and 3- 5 wt % of CI and is treated by the pyrometallurgical processes to recover Zn as Zn oxide. Direct hydrometallurgical processing is one of the most effective methods to recover high purity Zn. In this case, CI in the EAF dust is dissolved in the liquid phase by leaching, and the CI anion in electrolyte attacks anodes which are commonly made of a lead base alloy. Several processes have been proposed to remove CI anions from acidic sulfate solution. In this study, an electrolytic process was examined to eliminate CI anions from Zn sulfate electrolyte. From our study it can be said that the elimination rate of CI anion depends on the anode material ( i.e., the elimination rate is Pb-Ag alloy == Pb > DSE== Pt). In industrial Zn electrowinning process, the electrolyte contains Mn, which means the influence of Mn should be considered in the elimination of Cl. Mn dioxide deposition on an anode plate reduces the efficiency of CI removal. A periodical reverse current electrolytic system was examined to prevent this efficiency decrease, and deposited Mn dioxide could be removed very rapidly when the current is reversed. More than 95% of CI anion could be removed by this method in a shorter period than direct current method.

Jan 1, 1997

By Yonghua Li, Fanling Meng, Weitao Zheng, Xiaodong Wang

The NiTi thin films were deposited onto copper substrates by magnetron sputtering. Tensile tests were carried out on CSS-44100 electron universal test-machine. X-ray diffraction profile Fourier analysis method has been used to study the mechanical properties of deformation NiTi thin films. The surface micrographs of the NiTi thin film were obtained using scanning electron microscopy (SEM). It has been found that the dislocation density and the deformation storage energy density increased with elongation increased. Microhardness was calculated from the dislocation data. The results showed that the microhardness values were not in a good agreement between calculated values and measured values. The oxide layer on the surface of NiTi thin film affects the measured values of microhardness. The Vickers hardness measured values are larger than the calculated values. The experimental results showed that a series of parallel cracks grew in a concerted fashion across the thin film and the cracks were equally spaced.

Jan 1, 2015

By Shujian Jia, Mingming Song, Gaoyang Song, Bo Song, Yuhou Yang

An innovative method is investigated to separate inclusion particles from liquid metal by super gravity. To make clear the characteristics of the inclusion separation, Al melt containing MgAl2O4 particles with diameters less than 150 μm has been treated under various super-gravity fields. The thickness of particle-accumulated layer formed at the bottom of the sample and the area fraction, number density and size of inclusions were measured. It is found that the thickness of the particle-accumulated layer decreases and the area fraction of particles at this location increases with the increase of super-gravity field. With the gravity coefficient G=500, time t=2 min, and temperature T=1023 K, it is hardly to find any solid particles in the upper and middle areas of the sample and the separation efficiency is up to 90%.

Jan 1, 2015

By Stuart D. Miller, Clayton L. Rumble

"A field net acid generation (NAG) test procedure has been utilized on-site to identify, classify and map potentially acid forming overburden at the PT Kaltim Prima Coal (K.PC) mining operation situated in the tropical equatorial region of East Kalimantan, Indonesia. The field procedure involves routine use of a calibrated, site specific NAG test (rapid oxidation test using hydrogen peroxide) which has a tum-around time of less than 24 hours and requires minimal sample preparation. It is used on geological drill-hole samples, for forward planning and overburden management; blast-hole samples, for day-to-day operational control and overburden scheduling; and final dump surface samples, for verification testing. This operational monitoring program has been in use at KPC for the past four years.Calibration and implementation of the field procedure has involved validating the NAG test using conventional acid-base accounting techniques, producing an overburden geochemical classification scheme, optimizing laboratory and sample preparation procedures, and ongoing quality management. This paper presents background theory and practical application in a case study format."

Jan 1, 1999

By Ann M. Hagni

Electric arc furnace (EAF) dust from the secondary steel industry contains lead, cadmium, and chromium that causes it to be classified as a hazardous waste. Pyrometallurgical treatment of EAF dust is directed at recovering zinc and simultaneously rendering the dust non-hazardous. The mineralogy of the EAF dust is important in determining the occurrence and phase relationships of the zinc, lead, cadmium, and chromium contents. The principle phases in EAF dust as determined by reflected light microscopy, SEM-EDS, and XRD are solid solutions of the iron spinels (franklinite, magnetite, and jacobsite), zincite, hematite, and Ca-Fe-Si glass. Chromium is present in small amounts in solid solution in the spinels. Cyclone sizing of the minus 53 pm particles shows that more than 50% of this size fraction are less than 10 pm in diameter. The <I0 pm particles contain zinc as both franklinite in solid solution with magnetite and jacobsite, and zincite as determined by transmission electron microscopy and XRD. Auger electron spectroscopy did not detect coatings of volatile phases on the surfaces of EAF dust particles.

Jan 1, 1994

By Kent D. Peaslee

When supersonic oxygen jetting is used in electric furnace steelmaking, the lance jet axis is typically inclined at larger angles to the vertical than is used in basic oxygen steelmaking. The supersonic jet is important not only for refining the steel, but for sustaining the foamy slag in the electric furnace. Physical modeling was carried out using a room temperature, two-dimensional slice apparatus in which mercury represented the metal and water-glycerol the slag. High speed video photography with image analysis was used to study the effects of the angle of inclination on the slag/metal bath. Mathematical modeling using FLUENT provided a method of predicting flow patterns and the trajectories of drops injected at various points in the flowfield. A one-half scale water model of the system, in which lance heights, angles, and flowrates simulated those encountered in steelmaking operations, was used to provide a better understanding of some aspects of the oxygen blowing process in electric furnace steelmaking.

Jan 1, 1994

By Merete Tangstad, Lars Klemet Jakobsson

"Slag refining is a promising refining method for boron removal from silicon as a part of a metallurgical route for production of silicon for solar cells. There is, however, limited data on the distribution of impurity elements between silicon and different types of slags. In the present study, the distribution of boron and calcium between silicon and slag were determined at 1600 °C for calcium silicate slags with a CaO/SiC>2 ratio between 0.65 and 1.3. An almost horizontal linear trend was found for the distribution of boron between silicon and slag, and the borate capacity was found to follow the relationln(CB0, ) = 30.8 + 2.96-V (1)where V\s the CaO/SiCh mass ratio within the range of the experiments.IntroductionSolar grade silicon feedstock contributes significantly to the total cost and energy required to make crystalline silicon solar cells. A less expensive and less energy requiring method of solar grade silicon production is therefore needed in order to make crystalline silicon solar cells more viable as an energy source. Silicon is an abundant element and the manufacturing cost of solar grade silicon is therefore mainly determined by costs related to purification of metallurgical grade silicon. The Siemens process is the most common process today, but it is an expensive and highly energy requiring process that gives silicon with a higher purity than is needed for crystalline silicon solar cells. A cheaper and less energy requiring method for production of solar grade silicon can either be achieved by modifying the Siemens process or by using a new production method. Purification of metallurgical grade silicon through a metallurgical route is a promising method that is already in use industrially. It has however proven to be hard to lower the boron content to 0.3 mg/kg or less, which is the requirement for most p-type crystalline silicon solar cell manufacturers. Slag refining is seen as one of the most promising approaches that can be used to bring down the boron content to the required level, but there is not much data on how boron is distributed between silicon and binary calcium silicate slags [1-4]. The distribution of boron between silicon and calcium silicate slags at 1600 °C has been studied in this work, and the obtained data has been used to calculate the borate capacity of binary calcium silicate slags."

Jan 1, 2012

By C. W. Vierrether

Mineralogical analysis contributes directly to the selection of applicable beneficiation techniques for a given site. Tentative remediation methods for use on the Sharon Steel tailings in Midvale, Salt lake County, UT, were determined in part by mineralogical characterization. A systematic characterization scheme was employed to identify mineral species, mineral associations, and grain size. This paper presents the mineral content and distribution data collected for site characterization. This data was used to determine areas that were representative of the total tailings at the Sharon Steel site. Although this was the main focus of characterization, other useful information was obtained. The approximate location of "old jig tails" was identified and insight on possible arsenic, mobility through the pile was also obtained from the mineralogical study.

Jan 1, 1991

By S. P. Marsh, D. Banerjee

"Casting processes involve phenomena that occur on widely disparate length-scales. Simulation of macroscopic effects, such as heat transfer and convection, are generally addressed by solving the appropriate equations in discretized form on a finite-element mesh. Microscopic phenomena are described by micromodels that may be empirical or analytical in form. Coupling of phenomena in these two regimes is a critical issue in predicting microstructure and defect formation resulting from macroscopic process conditions. A formalism has been developed for expressing micromodels in a consistent manner using stereological parameters to quantify the geometric characteristics of the developing microstructure. This approach provides a robust and physically consistent method for coupling local micromodels with the macroscopic fields. The macroscopic state variables at each node serve as global constraints on the micromodels that are applied to a local unit volume. An outline of an equiaxed solidification model based on this approach is presented, along with preliminary simulation results. Coupling of convection and enthalpy effects between the micro and macro regimes is also discussed. IntroductionThe primary goal of casting simulations is to improve the reliability of cast parts while minimizing cost and development time. Effective simulations can speed up the mold design process and reduce the likelihood of defective parts by refining a particular casting process on a computer, reducing the dependence on cost- and time-intensive prototype castings. The challenge in developing effective simulations stems from the need to address physical processes that occur over a wide range of length-scales, from microscopic (atomic) and mesoscopic (microstructural) scales to macroscopic distances comparable to the size of the casting itself. Overviews of the various thermophysical phenomena and computational factors that are important in solidification modeling are provided in the literature by Rappaz [1] and Tseng et al. [2].Macroscopically, the solidification process is largely governed by the rate of heat flow from the alloy through the mold wall. Another important effect that occurs on the scale of the casting size is convective flow of the melt, which is driven by density-variations in the melt. Macroscopic calculations employ finite-element or finite-difference methods to solve the sets of equations that govern these effects, and the spatial resolution is determined by the grid spacings used for the calculations. Typical spatial resolutions are on the order of 10-2 to 10-3"" meters. This represents a compromise between the resolution required to simulate the continuum transport processes accurately, and the computational time required to model the entire solidification and cooling process."

Jan 1, 1994