Search Documents

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Jyri Talja, Shaolong Chen, Hannu Mansikkaviita

"Drying (water removal) prior to smelting is always economically feasible. Unnecessary heating of vapour can thus be eliminated resulting in savings of5-15 MUSD every year.Thermodynamically removal of one ton of water out of copper concentrate at 100 °C (with 10 % moisture) requires approximately 3150 MJ/tH2o, consisting of heating of the water (377 MJ), heating of the concentrate (509 MJ) and water evaporation (2260 MJ). This is quite independent of the selected drying technology. In reality some more heat is needed as higher temperature is practiced to enhance the drying performance and to reduce the equipment size.Major nominator in drying energy efficiency is amount of gases, which depends greatly on the drying technology. Dryers based on direct heating with fossil fuels have high gas flow rates, and thus they require additional energy of about 1400-1600 MJ/tH2o, compared to indirect modemsteam drying at 250-400 MJ/tH2o.Significant benefits in energy consumption (900-1300 MJ/tH2o) with additional potential for a bonus profit of 2-4 MUSD/y year, together with full elimination of some 40 000 tpy CO2 per mid-size dryer is available by selecting sustainable, energy efficient steam drying.IntroductionRemoval of water from the concentrate is very energy intensive thus having a significant environmental impact. However, drying prior to smelting is always economically feasible and very often viable also from the perspective of process operations. This environmental impact of drying can, however, be decreased or even fully eliminated with proper selection of the drying technology.Energy incorporated in drying consists always of a number of phases like liquid (water), solids (concentrate) and gases (water vapour, purging I dilution air, combustion gases). Each phase is heated to a specific temperature during the drying process.Heating of water, heating of the concentrate and water evaporation consumes more or less the same amount of energy despite of the drying technology (3150 MJ per ton of water). In conventional drying this amount of energy is achieved by combustion of fossil fuels wirg subsequent CO2 emission. Alternatively, chemical energy derived from sulphide smelting can be utilized in a form of steam thus generating zero emission ofCO2, in modem steam drying."

Jan 1, 2012

By Nils Eivind Kamfjord, Roar Jensen, Ingeborg Solheim

"SINTEF has carried out several pilot scale silicon process experiments in the past, but always with an open off gas system. In order to test the possibilities in running a semi closed furnace operation, a new off gas hood has been designed and tested. The off gas hood is designed to collect all off gases to gain insight into the phase compositions in the off gas and at the same time have the opportunity to monitor and maintain the charging/stoking of the furnace. The furnace hood has regulation and control of the air inlet into the combustion zone in two different heights. The off gas temperature and composition was continuously monitored and analyzed during the experiment. In order to expand the knowledge on NOx- formation in silicon metal production, such information is vital.IntroductionBecause of the negative environmental impact, the attention towards all kinds of NOX emissions increases in Norway. The authorities’ demand towards better surveillance and control of emissions increases as well.Earlier and new industrial measurements in FeSi- and Si-metal furnaces reveal quite high NOX-emission. The measurements also show that the NOX formation (mainly as thermal NOX) is distinct connected to the formation of dust (SiO?SiO2) in the combustion chamber above the furnace surface, when the temperature is high and the access to N2/O2 is good. This means that stoking, charging and temperature straight above the furnace surface is important factors for the NOX formation."

Jan 1, 2012

By Kenneth L. Driggs

The 1988 shift in primary smelting facilities from low grade matte (35%) reverberatory furnaces to high grade matte (63%) flash smelting heavily impacted a very stable and successful converter operation. Low matte grade converter campaigns averaged 36,000 short tons of copper and revert production/consumption was in balance. The conversion to high matte grades necessitated oxygen enrichment of converter blast and revisions in operating practices. After two years of operational development, campaign life has risen to over 40,000 short tons and revert production/consumption is again in balance.

Jan 1, 1991

By Markus A. Reuter

In this paper various hybrid modelling architectures are proposed for the modelling and metallurgical control of pyrometallurgical reactors. Discussed are architectures in which data reconciliation is combined by thermochemical, neural net and dynamic modelling to improve the models. At the same time the data reconciliation models can act as soft-sensors for estimating unmeasurable data. Cases that are discussed are (i) the modelling of a submerged arc furnace for the production of thermal phosphorous, (ii) the processing of Sn-Pb-Zn flue dust (originating from secondary copper) in a hearth furnace, (iii) modelling of a steel converter, and (iv) dynamic modelling of a flash smelter.

Jan 1, 2001

By Wang Chen

COREX process is briefly introduced. A static model combining a set of mass and heat balance equations has been developed. Taking the specified inputs from the graphical user interfaces, the model is capable of calculating the consumption of raw materials and fluxes, the volume and composition of the slag and the volume and composition of the generator gas. The model enables the examination of the changes of materials and energy flows induced by the variations of operational parameters and raw materials chemical analysis. The model allows a detailed process analysis and adjustment of the plant operation and can thus be used to improve plant operation.

Jan 1, 2008

By V. P. Bystrov

Vanyukov process has been developed and investigated in Russia over the last 25 years. It has been established that various kind of material could be treated in Vanyukov process. The results of the pilot plant trials as well as industrial experience are presented in this paper.

Jan 1, 1993

By Peter Koh

The velocity solid charge attains when dropping down concentrate chutes is an important boundary condition when developing mathematical models of flash furnace burners and reaction shafts. In this work an experimental rig was developed to measure the velocity attained when nickel concentrate and sand were dropped down a vertical pipe 3m long. The velocity measurements showed that the nickel concentrate did not fall as individual particles. The measured values of the velocity approached, but did not attain, those calculated for solid bodies, the disparity being attributed to friction at the pipe wall and fluid drag losses. After falling 2 m velocities between 5-6 m/s were attained. The analysis was extended and applied to understanding the intermittent problem of puffing which sometimes occurs from the top of the concentrate chute. The pressure at the bottom of the chute is the net result of two opposing pressures, namely that developed by (a)the process air entering through the velocity control device, and (b) the solids falling down the concentrate chute. Flow back up the chute occurs when the former exceeds the latter. The process air pressures in the burner were obtained from CFD simulations of a full burner. Variables considered included air speed through the velocity control device, drop height and furnace draft. The analysis was useful in highlighting the operating conditions which were conducive to puffing and in establishing procedures to minimise its occurrence.

Jan 1, 2006

By Gerhard Bayer

X-ray and thermoanalytical studies were carried out on the formation and stability of Ca-, Mg-and Mn-tungstate, and of the corresponding minerals scheelite and wolframite. The tungstates were synthesized by different methods: precipitation from solution, solid state reactions, displacement reactions with solutions and in the solid state. The reactivity of natural scheelite and wolframite with different salt solutions and in mixtures with other minerals was investigated.

Jan 1, 1989

By Giuseppe Granata

An innovative process using titanium tetrachloride (TiCl4) gas as reactant has shown successfully to obtain titanium through electro-winning of TiCl2 formed in-situ on titanium cathode. The process involves a continuous feed of TiCl4 gas reacting onto a titanium cathode immersed in a molten salt (NaCl-KCl), whereby in-situ formation of titanium dichloride (TiCl2) through a disproportion reaction. Simultaneously, the TiCl2, thus in-situ formed in the molten salt media, has been reacted into chlorine gas and titanium, the latest electrodeposited on the titanium cathode by electrowinning. The reaction kinetic of this innovative process was investigated in terms of TiCl2 in-situ formation rate and galvanostatic electrodeposition rate, where, in particular, the effect of operating variables such as TiCl4 partial pressure and flow rate, as well as temperature and galvanic potential applied was investigated.

Jan 1, 2014

By Jae-Ho. Lee

For some electronic applications where a dispersed electrically-conductive particulate-phase is employed, the conductivity of the surface (or near-surface region) of the particles provides for the primary mechanism which determines its electrical conductivity. Particles of a less expensive material, which may have desirable thermal-expansion properties, when coated with silver offer a means of also obtaining desirable electrical properties and at low cost. The research conducted was focused primarily on the development of silver-coated tungsten particles for thick-film polymeric conductors. The ammoniacal electrolyte was formulated from silver-nitrate, glycine inhibitor and formaldehyde reductant. The reduction, and subsequent deposition, of silver occurred selectively on the surface of the tungsten particles. Coated particles were assessed by SEM imaging. The thickness of the silver coating was estimated to be approximately 100nm on the basis of a mass account and the coating being uniform. The electrical conductivity of a silver-coated tungsten-powder pellet was found to be similar to that of a silver-powder pellet, of identical geometry.

Jan 1, 1997

By Xiang Sun

Microwave processing has been under continuous development as an advanced heating method in modern industries. However, problems with uneven heating still remain. Although heating uniformity is highly dependant on the properties of the materials being heated, proper furnace design to prevent uneven field distribution is another important factor. As an alternative to experimental measurements and adjustments to find appropriate furnace parameters, computer simulation is a convenient method for modeling, understanding, and improving the uniformity of microwave heating. This paper discusses current modeling technologies as well as applicable techniques for improving microwave heating uniformity. The purpose is to give a basic understanding on how to find, analyze, and minimize the problems associated with uneven heating in microwave processing.

Jan 1, 2006

By Paul L. Wichlacz

A mathematical model of growth and ferrous iron oxidation for attached bacteria was applied to rotating biological contactor (RBC) units treating acidic mine drainage. The model describes attached bacterial growth as a saturation function, where the rate of substrate utilization is determined by a maximum substrate oxidation rate constant, a half saturation constant, and the concentration of substrate within the RBC. The maximum oxidation rate constant was proportional to flow rate and the substrate concentration in the reactor varied with influent substrate concentration. The model was tested at three separate sites and with three different size RBC units. The ability of the model to predict the rate of iron oxidation under all test conditions was significant. The accuracy of the model was found to be affected by unit size and vary with specific test site.

Jan 1, 1985

By Michael K. Rhodes

A 120 tonne per day BacTech bacterial oxidation plant treating refractory gold concentrates for Gold Mines of Australia&apos;s Youanmi project in Western Australia commenced operation September 1994. This was the first commercial application of the BacTech process. A pilot plant trial on concentrates produced from Youanmi ore was carried out at BacTech&apos;s laboratory in Perth. Results and measurements from this trial were used by Signet Engineering Pty Ltd to design the commercial plant. This paper cover the results obtained from the piloting, their implementation in the plant design and the initial commissioning of the full scale plant.

Jan 1, 1995

By B. Mishra

Several reactive metal purification processes using molten salts generate effluent from which significant quantities of metal can be recovered prior to discardinglrecycling the salt. A Salt-scrub [SS] process has been applied where the reactive metals are recovered as a metal-gallium alloy by calciothermic reduction of the metal compounds. The SS alloy compositions were produced by mixing, pressing and sintering the metal-powders. Measurement of metal recovery has been studied for cerium, silver, tin and lead. The process has been optimized for variables such as the metal quantity per kg of effluent salt, amount of excess calcium over stoichiometry, stirring rate and time and holding time at reduction temperature. Over ninety-seven percent metal recovery has been obtained under optimized conditions. The development of an alloy for efficient Salt Scrub processing reduces a major contaminated waste disposal problem as well as recovering the valuable reactive metal. Surrogate metals have been used in this work to study the behavior of plutonium.

Jan 1, 1994

By R. N. O'Brien, E. Peters

"It has been discovered that copper concentrates can be leached in strong (40-60%) sulfuric acid with nitric acid, or with oxygen if nitric acid is present as a catalyst. Chalcopyrite is rapidly decomposed at temperatures well below the boiling temperature of the lixiviant (-150 C.) and the resulting copper and ferric salts are precipitated as CuS04.H20 and FeH(S04)z.4H20. Other metal sulfides such as zinc, lead, nickel, etc. are also converted to sulfates that are nearly insoluble. Sulfur is partially converted to elemental and partially to sulfuric acid. Reduction products of nitric acid can be recovered from the distillate with good recovery. Conversion of as-received copper concentrates is largely complete in about 1 hour. Introduction9 molar sulfuric acid is an unusual hydrometallurgical lixiviant: it has a boiling point of about 150 C. and a low solubility for base metal sulfates. Below about 6 molar acid, the boiling point falls below 120 C. and yields much higher sulfate salt solubility, while above 12 or 13 molar acid and at higher temperature sulfuric acid becomes an oxidizing agent, yielding gaseous S02' Thus, sulfuric acid within this range of concentration is capable of acting well above the temperature of boiling water without requiring autoclave conditions, and if typical oxidative leaching conditions are applied to suspended mineral sulfide concentrates, it is possible to obtain a conversion of these sulfides into 'crystalline sulfates. Thereafter, the sulfates can be separated by filtration or by solid - bowl centrifuge and the solution can be recirculated to the reactor vessel. Meanwhile, the solid sulfates can be treated in a typical hydrometallurgical circuit, i.e., dissolved in a return stream that is essentially water, separated from each other by, for example, solvent extraction, and recovered as metals by electrowinning."

Jan 1, 1997

By Barry J. Welch

The production of primary aluminium can potentially lead to metal that, with minimum treatment, meets a high purity standard. Smelters that can achieve a significant proportion of their production in this manner have a competitive edge which is of growing importance as the use grows for such items as compact discs and the like. Superimposed on the desire to produce high quality metal are stringent environmental requirements that the industry must adhere to. The environmental &apos;legislation focuses on fluoride emissions and the approach adopted is towards a zero waste management philosophy. The fluoride recycling process does, however, result in volatile impurities being captured and recycled to the cell. Aluminium has an extremely high reduction potential and this results in a significant proportion of the recycled impurities being reduced at the electrolyte metal interface and thus contaminating the metal. This paper reviews sources of impurities and the impact of the operating procedures adopted on metal treatment.

Jan 1, 1996

By Semih Perdahcioglu, Arthur E. Morris

"The curricula for the majority of Materials Science and Engineering programs is devoid of all but the most rudimentary coverage of the principles of material and energy balance calculations. As a result, graduated engineers that need to make such calculations are faced with three unpalatable options. First, attempt to learn the subject by attending workshops or short courses sponsored by corporations or industry groups. Second, outsource the needed work to a consulting engineering company. Third, purchase a software package that's capable of simulating a process. Each of these options require a considerable investment of employee time and effort. The first option might be the best if suitable computational software was readily available. We review the recent development of such software, which is entirely based in Excel. The software tools include a thermodynamic database, tools for multiple computations, and a flowsheet simulation program. These tools employ teaching by simulation.IntroductionPracticing engineers often come up with situations where they must learn a technical subject that they didn't cover in their college classes. One possibility is to obtain a couple of texts on the subject, and delve in. Or, they may sign up for an intensive short course where they can get personal instruction and guidance. But the first option requires a lot of study time, and the second option may not provide the specific instruction (or intensity of instruction) required to appropriately master the subject. Here we look at ways of using simulation techniques to learn the methodology for making material and energy balances on industrial processes.Industrial heating processes have undergone many changes over the past dozen years, as vendors have introduced new heating equipment designed to recover the greatest possible amount of heat from the fuel, and to meet stringent environmental challenges for emissions (especially NOx). Even though the recent unprecedented drop in price of natural gas may have altered the urgency for improving a plant's energy efficiency, the need is still there. Until recently, there was a dearth of readily-available software for process engineers to use for simulating a plant's flowsheet. The good news now is the existence of several Excel-based software tools that make the calculational process much easier. [ 1]. Plant engineers may also be interested in a DOEsponsored program[2] which allows plant-wide and ""what-if' analyses of the energy balance."

Jan 1, 2013

By K. Pagalthivarthi, P. V. Desai

"During solidification of alloys, many inter-related physical processes, such as melt convection, mass diffusion, heat transport, macrosegregation and melt-undercooling occur. Several research workers have studied one or more of these effects separately. To answer important questions on solidification behavior, an overall approach interrelating the processes is necessaryAs a first step toward accomplishing the overall modeling, the freezing of a binary liquid metal is examined. The various stages during freezing of the alloy are critically described to build a continuum model for the entire process. Diffusive mixture theory is used to write the conservation equations for the liquid and the mushy zones. The concept of local thermodynamic equilibrium in the presence of curvature effects is used to restrict the number of degrees of freedom within the mushy zone. Constitutive equations relating flux quantities and affinities, the governing differential equations and boundary conditions are discussed briefly for the freezing process.IntroductionA solidification study encompasses such facets as solifidication time, microstructure, macrosegregation of the solute, shrinkage effects and soundness of the casting. Influence of one or more of the coupled heat and mass transfer phenomena such as local solute redistribution, thermosolutal convection, melt undercooling at dendrite tips and heat dissipation to the ambient have all been previously examined [1-3J. Several studies have examined the individual facets of alloy solidification as isolated processses. In fact, the transport processes occur simultaneously and a comprehensive model should include their inter-relationships. In particular, some of the existing studies of the mushy zone [4-6J do not emphasize thermodynamic completeness. This work represents an attempt to develop a thermodynamically consistent model of the entire solidification process on physical grounds."

Jan 1, 1986

By J. van Driel

NOx is a growing concern for acid plant operators due to recent legislation reducing the allowable stack limits, as well as continually more stringent requirements for product acid quality. NOx also causes a major problem during maintenance as NOx rich acid residues fume following exposure to moisture in the air. Until recently, the solution for NOx related issues was to treat the symptom, rather than the cause. NOx in product acid was treated using chemicals and the NOx in the plant stack was generally left untreated. As part of an environmentally driven change in concentrates, Budel Zink installed the first gas phase NOx destruction process to be incorporated into a commercial scale acid plant. Nitrogen oxides contained in the process gas are reduced selectively with ammonia over a catalyst to form nitrogen and water. As a result, the NOx reduction is in agreement with the permit requirements.

Jan 1, 2002