Search Documents

By De-qing Zhu, Jian Pan, Tie-jun Chun, Dong Chen, Yu Cui

"A study of processing pyrite cinder and metallurgical slag using “one step” technology in strand grate - rotary kiln is presented, which aims to efficiently recover the valuable metals of iron, lead, zinc and copper. The effect of chloridizing roasting parameters including roasting time and temperature on the removal rates of nonferrous metals was investigated. It is shown that copper and zinc are difficult to remove and lead is removed more easily. The preheated pellets were reduced in a rotary kiln, where zinc and lead can be removed easily and high iron grade and good metallurgical performance prereduced pellets can be obtained. Furthermore, the chlorination and the reduction mechanisms of copper, lead and zinc are discussed. It is revealed that the phases of copper, lead and zinc in slag are complex and ferrite and silicate of metals are difficult to remove.IntroductionAs two kinds of significant secondary resources, metallurgical slag and pyrite cinder contain not only abundant iron but also considerable copper, lead, zinc and so on. Several tens of millions of tons of metallurgical slag and pyrite cinder are discharged in nonferrous metal and chemical industries annually in China [1, 2]. In addition, the accumulated waste slag in storage is more than one hundred million tons, which not only occupies much land but also pollutes the environment [3]. However, because the metallurgical slag and pyrite cinder are treated by high temperature processing, the properties are distinctly different from the properties of natural ores, and iron is in close association with copper, lead and zinc. So, metallurgical slag and pyrite cinder are difficult to efficiently utilize and only a small amount is used as additives in cement, paving, brickmaking and auxiliary additives [4-7]."

Jan 1, 2011

By Shengli Wu, Mingyin Kou, Laixin Wang, Zhe Wang, Xinliang Liu

The sticking behavior of iron ores in the shaft furnace is one of the most important problems in the COREX melting progress, which directly influence the smooth operation and productivity of shaft furnace. Therefore, it is of great importance to study the sticking behavior of pellets in COREX shaft furnace. The results showed that porous metallic iron produced at the interface of pellets samples was the main reason for the sticking of pellets in the COREX shaft furnace. The SI (sticking index) and metallization rate increased with the reduction temperature and gas flow, and decreased with melting rate. However, the SI of pellets in the COREX shaft furnace could be decreased by the proper match of melting rate and reduction temperature, reduction temperature and gas flow, while the metallization rate of pellets were kept at a certain level. Furthermore, the matching of melting rate and reduction temperature was more effective than the matching of reduction temperature and gas flow.

Jan 1, 2016

By Axel Hoppe

Although Tantalum is not usually regarded as a precious metal, its pricing structure is very similar to that of Silver. Different from precious metals, Tantalum has only industrial applications and its use is about 1000 metric tons per year. The intrinsic value of Tantalum already in .the past was a driving force for its recycling. Based on these facts the Tantalum industry world-wide is approaching the closed-loop concept of its recycling. A detailed material flow of Tantalum processing as well as recovery of residues and used products will be discussed.

Jan 1, 1995

By Jeffrey F. Adams

Gypsum fouling is a common problem in the hydrometallurgical industry. It is a particular problem in free sulphuric acid neutralization, or iron removal operations where sulphates are removed from aqueous solutions by the addition of calcium-containing bases. Previous work revealed a strong correlation between the degree of gypsum supersaturation in the reactor and the rate of scale growth indicating that scale formation and growth are primarily controlled by chemical phenomena. However, the chemical behaviour of gypsum is variable and unpredictable with solution chemistry and temperature. Many of the "rules of thumb" that are used to predict its behaviour (and avoid fouling) are in fact based on gypsum solubility in water, rather than on real mixed metal sulphate systems. However, despite this unconventional solubility behaviour, we have been able to accurately model it in Ni, Mg, and Zn containing solutions over a wide range of temperature (25°C-90°C) and solution concentration (0-6 m) using the OLI simulation software. Furthermore, by studying fouling rates in a simulated continuous neutralization reactor, the relationship between process conditions and fouling rates were explained for the first time. This has led to an understanding of how techniques for minimizing gypsum fouling work.

Jan 1, 2003

By Sung Wng Kim

The binary antimonide compounds with the skutterudite structure have a potential for thermoelectric applications because of the high carrier mobility, high thermoelectric power, and relatively low thermal conductivity due to the complex crystal structure. However, the room temperature thermal conductivity of these skutterudite materials is as high as about IOW/mK with an estimated 80-90% contribution from the lattice thermal conductivity. Because the lattice thermal conductivity of related ternary skutterudite compounds can be substantially reduced due to the additional phonon scattering, a study of thermoelectric properties of these compounds is of interest. The binary IrSb3, ternary Ir1.xRuxSb3 and Ir(MxSb1.x)3(M=Ge, Sn) compounds were prepared by hot pressing of pre-reacted powders. We have measured the electrical resistivity, thermoelectric power, and thermal conductivity, in a temperature range from room temperature to 973K. The binary IrSb3 compound is found to have P-type electrical properties exhibiting a good Seebeck coefficient (up to 225µV/K around 773K), electrical resistivity(5x10-5Ohm M around 933K), and relatively low thermal conductivity(6W/mK around 950K). The lattice thermal conductivity, K[2] was calculated from the Wiedemann-Franz relationship.

Jan 1, 2002

By Vahid Rastegar

"Characterization of the microstructure and revealing dendrites in the microstructure and also measuring the dendrites arm spacing and the distribution of silicon were studied in various pieces of compacted graphite cast irons with 0.17, 0.185, 0.2, 0.22 and 0.24 percent of mischmetal. Black-white and color metallography (quantitative and qualitative) were carried out on the various steps of the cast samples. Distribution of silicon was studied quantitatively using spot analysis with scanning electron microscopy. Furthermore, effects of two variables (cooling rate and mischmetal percentage) on dendrites arm spacing were investigated.In order to color metallography, the samples were plunged into a boiling solution of 18% KOH, 9% NaOH and 9% picric acid in distilled water. It was inferred that the microstructure coloration varies according to the sequence: green-->red-->yellow-->blue-->dark brown->light brown as the silicon content decreases. After observing dendrites, dendrites arm spacing was measured. In this method, it seems to be possible to predict the mechanical properties of compacted graphite cast irons by knowing dendrites arm spacing and without any destructive testing. After studying the two variables, it was concluded that dendrites arm spacing decreases as the amount of mischmetal increases and it increases as the cooling rate increases.IntroductionIn general, detecting of primary austenite dendrites is not possible in cast irons due to their solidification system. Observing the dendrites in the room temperature is possible only in those gray cast irons that contain type D graphite. With collecting data of dendrites arm spacing (DAS) measurements, it could be possible to achieve the mechanical properties of cast irons without any destructive testing. In this research by applying a particular method, primary austenite dendrites and also distribution of silicon in the microstructure has been observed."

Jan 1, 2012

By Anestis Vlyssides, Elli Maria Barampouti, Sofia Mai, ?postolos Vlyssides

"A new anaerobic reactor variation, the UASB/CO2-stripper reactor was conceived. It consisted of a conventional UASB reactor that recirculated the biogas produced. The sludge characteristics of this system were examined when treating high strength wastewater. From the data collected, it was obvious that the UASB/CO2-stripper system can satisfactorily operate at higher loading rates (25 g COD·L-1·d-1). A pronounced effect on the quality of the granular sludge was observed. The VSS/TSS ratio decreased sharply. A considerable decrease in the mean granule diameter was observed, while the specific gravity of the granules increased. The sludge bed porosity increased significantly leading to a considerable expansion of the sludge bed. These changes in the sludge properties led to a gradual shift of the system towards a fluidized bed process as far as its hydraulic characteristics were concerned.IntroductionIn recent years energy considerations and environmental concerns have increased the interest in direct anaerobic treatment of industrial wastes. The anaerobic method of waste treatment offers, under the present circumstances, a number of significant advantages with trivial or more serious drawbacks over other treatment methods. The major obstacle to the application of the process for this specific purpose is perhaps the difficulty of extending it to a stable and simple operational form. A number of reactor configurations has been developed leading to high biomass concentrations, e.g. the contact process, the filter reactor, the UASB reactor, and the fluidized bed systems, but the process stability problem still remains [1].A prime objective in the operation of anaerobic waste treatment process is the maintenance of a proper pH range. Thus, a possible solution to the process stability problem could be obtained by increasing alkalinity in the anaerobic systems. Therefore, the main objective of this paper is to present and evaluate the results of a system (UASB/ CO2-stripper) with increased alkalinity concentrations."

Jan 1, 2008

By Vinod K. Namilakonda

In situ synthesis of discontinuously reinforced aluminum alloy metal matrix composites was investigated. Aluminum alloy (A356: Al-7 wt% Si) was reinforced with dispersed AlN particles. Thermodynamic calculations were made for the composition determination of various phases formed during bubbling of NH3 gas into the Al alloy melts in the temperature range 1173-1473 K. Experiments were carried out for in situ production of AlN particles with the reaction between Al melt and NH3 gas in high temperature resistance furnace at 1473 K. The products were characterized using SEM, EDS and XRD. Effect of bubbling time of NH3 gas on the AlN formed in the composites was studied. The amount of AlN reinforcement in the Al alloy composites was observed to be in the range of 5 to 35 wt%. Good agreement was observed between the experimental and thermodynamic calculated data on the composition of AlN in Al alloy composites.

Jan 1, 2006

By Gary R. Adams

Coating thickness control is typically difficult with touch-up solders for galvanized steel, and corrosion properties and abrasion resistance are sometimes poor. This paper reports on progress in ILZRO-sponsored research to develop an improved touch-up solder. Encouraging results were achieved in torch soldering trials with zinc-tin based alloys. Mouldability and coating thickness control were achieved over a practical working temperature range in which the solders consisted of a viscous mixture of solid primary zinc phase particles in a liquid zinc-tin eutectic matrix The mouldability was dependent on the microstructure of the starting material, and optimum structures could be obtained through control of casting solidification rates and/or by the addition of small amounts of copper. Hardness and preliminary corrosion test results showed potentially good mechanical and corrosion behaviour. The absence of toxic materials ensures environmental friendliness. Comprehensive performance testing is continuing on selected experimental zinc-tin-copper touch-up solders.

Jan 1, 1992

By Th. Probst, M. Reuter, H. Orbon, U. Boin, J. Vonken, P. Vonk

Although secondary aluminum industry is well established in the world, the recycling process still requires further development to adequately control the process for a higher aluminum yield and a better product quality. In the present paper, recyclabilities of different aluminum scraps have been experimentally studied. Four types of commercial scraps were characterized and melted at 800 - 900 °C to recover 'aluminum metal with the protection salt flux of NaCl-KCl-Na3AlF6 under nitrogen atmosphere. According to the results, the difficulty of recycling aluminum scrap depends on the cleanness and the ratio of surface area to body volume. More non-metallic contaminates and higher ratio of surface area to body volume usually led to a lower metal yield. Usually cast ingots gave better results than rolling mill cuttings under similar conditions. Bottle caps can be recycled more easily than the margarine foil. The effect of temperature was not as significant as the composition of salt flux. The addition of cryolite was essential for a better metal recovery, especially for the scraps with higher surface area. Recycling

Jan 1, 2000

By Qinmeng Wang

The oxygen bottom blown copper smelting process is a new technology which has been widely applied to the copper production in China. In this work, a computational thermodynamics model for this technology has been established, based on smelting mechanism and theory of Gibbs free energy minimization. The calculated results from the model agree well with the actual industrial data, indicating that the model can be used for the predictions under different operating conditions. The tendencies of the key parameters (such as Cu losses and Fe3O4 content in slag) and the distribution ratios of the minor elements (such as Pb, Zn, As, Sb and Bi) can be predicted by adjusting the oxygen/ore ratio charged into the bottom blown copper smelting furnace. The model can be used to monitor and optimize the industrial operations of the oxygen bottom blown copper smelting process.

By Richard D. Hagni

The techniques of reflected light microscopy and cathodoluminescence microscopy are uniquely suited to the study of the products from many important industrial problems. Ref1 ected 1 ight microscopy provides the means to rapidly identify the mineralogy of an industrial sample, determine the abundance of each phase, and examine the mineral intergrowths or textures. Cathodoluminescence microscopy is a relatively new instrument that provides the means to cause many minerals to cathodoluminescence under the microscopy. The cathodoluminescence of a mineral allows it to be readily distinguished from other phases that differ in cathodoluminescence but are similar in optical properties. Cathodoluminescence microscopy is especially useful to detect cathodoluminescence minerals that are present in only small quantities. Reflected 1ight microscopy and cathodoluminescence microscopy have been successfully applied in studies of beneficiation products, prediction of beneficiation and leaching problems, phosphatic iron ores and mill products, pyrometallurgical products, roasted refractory gold-bearing sulfides, ceramic build-ups, electric arc furnace and smelter dusts, and other industrial products.

Jan 1, 1993

By A. G. Cecutti

A brief overview of the known significant health effects of both Nickel and Cobalt will be presented. Some time will be given to the current research activities, especially for Nickel. Emphasis will be placed on some of the controversial issues associated with their health effects.

Jan 1, 1988

By SenYang Qian, ShuangYu Du, Bo Wang, Jieyu Zhang, Jian Zhao

During the solidification process, the flow pattern of the molten steel has significant influence on the formation of solidification microstructure. In present study, the solidification microstructure of 30Cr2Ni4MoV steel ingot under different intensities of mechanical oscillation(forced convection) was simulated by using ProCAST®software. The results showed that the increase of the intensity of oscillation could restrain the development of the columnar grains and refine the grains. As the intensity of oscillation increased, the proportion of columnar grains decreased and the proportion of equiaxed grains increased. When the intensity of oscillation was at a low level, the effect of refining grains could be improved obviously by increasing the intensity. However, as the intensity increased to over 0.833, the effect of refining grains would not be improved.

Jan 1, 2016

By Bo Jiang, Jiusan Xiao, Hongmin Zhu, Kai Huang, Shuqiang Jiao

Carbothermal selective reduction of simulative titanium slag and various titanium raw materials were presented and SiO2 was found to be partially reduced, forming a series of Fe-Si alloys during the process. Thermodynamic analysis of the selective reduction between TiO2 and SiO2 was performed using HSC 6.0 software, then a series of equilibrium experiments were designed and presented. The activity of Si reduced from SiO2 was affected by the presence of Fe reduced from FeOx and the generation of Fe-Si alloys, promoting the reduction of SiO2 in the whole process. The results of experiment are in great accordance with the calculated data obtained from thermodynamic analysis.

Jan 1, 2016

By Shenghui Guo, Jianbo Lan, Hongying Xia, Jinhui Peng, Lihua Zhang, Libo Zhang

Spent Hawaii nut shell was converted into a high-quality activated carbon via steam physical activation. Analysis of the experiment including activation temperature, activation duration, steam flow rate on the adsorption capability and yield of activated carbon were identified. Response surface methodology showed that the activation temperature was identified as 866 , an activation duration of 36 min and a steam flow rate of 2.5mL/min with the methylene blue adsorption number of 195 mg/g and yield of 77.75%. The key parameters that characterize quality of the activated carbon such as the BET surface area, total pore volume and average pore diameter were estimated to be 1125m2 /g, 0.94mL/g and 5.21 nm, respectively. Additionally, by the SEM analyses of char and activated carbon, the surface of activated carbon has large number of pores of irregular and heterogeneous morphology.

Jan 1, 2016

By G. G. Richards

"The slag fuming process has operated for close to 70 years to recover zinc from lead blast furnace slag. The process is normally carried out through the batch treatment of slag by submerged injection of coal and air. Within the bath the coal acts as both a reductant, to reduce Zno to zinc vapour, and a fuel, to maintain bath temperature during the endothermic reduction process. The partition of coal between the slag, combustion and bypass is dependent on factors such as bath depth and injection pressure. The option of continuous fuming has been pursued at the D. Blagoev smelter in Bulgaria using heavy fuel oil as reductant/fuel. There has, however, been little attempt at commercial continuous fuming with coal. This paper presents an analysis of a coal-based continuous slag fuming furnace. The data on the Plovdiv fumer is used as a reference point. Critical design criteria for continuous fuming include the slag feed rate, degree of coal combustion and furnace size. Mathematical modelling analysis suggests that continuous fuming with coal can achieve respectable zinc/coal ratios.IntroductionThe slag fuming process was developed in the early part of this century to recover zinc from non-ferrous smelting slags [1-3]. The majority of installed furnaces were put in place to fume zinc from lead blast furnace slag on a batch basis. In most cases coal is used to effect reduction of zinc oxide, but one furnace uses natural gas [4] and, in a curious twist, a continuous fumer was developed based on fuel oil [5].Given the general nature of blast furnace lead smelting, it is not surprising that slag fuming has remained a batch process, in spite of the advantages that could be gained by moving to continuous fuming. Blast furnaces are usually operated as relatively independent units, and tapping has traditionally been done into ladles. The presence of a crane aisle makes direct coupling of the blast furnace to a slag fumer difficult, especially in a retrofit situation. Furthermore, steady-state blast furnace operation is not easy to achieve. The size of these furnaces and the nature of their feed make it difficult to guarantee constant operation."

Jan 1, 1996

By Jr. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated flotation methods for recovering fluorite and byproduct beryllium from the Fish Creek deposit of Nevada. The preferred method includes (l) fluorite rougher and cleaner flotation, (2) de sliming at 20 micrometers, (3) muscovite flotation, (4) silicate flotation, (5) hypochlorite wash of silicate concentrate, and (6) beryllium rougher and cleaner flotation from the silicate concentrate, Laboratory results showed that over 94 pct of. the fluorite was recovered in a concentrate containing 96 pct CaFz. Beryllium flotation produced .concentrates .containing in excess of 5 pct BeO with recoveries over 70 pct. A 1.00-lb/h continuous flotation unit was constructed to demonstrate this procedure,

Jan 1, 1985

By Yuanbo Zhang, Yingming Chen, Zijian Su, Bingbing Liu, Jun Chen

Iron, tin-bearing tailings is a kind of hazardous solid waste generated from cassiterite dressing operation. It is difficult to utilize the tailings by present mineral processing methods due to the complex dissemination characteristics. In this study, a process of gas-based magnetizing roasting followed by magnetic separation was studied for separating and recovering iron from the tailings. The effects of roasting and magnetic separation parameters on the recovery of iron were systematically investigated. The optimum parameters were proposed as follows: CO/(CO+CO2) content of 5%, roasting temperature of 850 C, roasting time of 60 min, grinding particle size of 90% less than 45 μm and magnetic field intensity of 800 Gs. Under these conditions, the magnetic concentrate containing 68.5% Fe and 0.06% Sn was achieved, which can be used as high-quality raw materials for direct reduction iron production.

Jan 1, 2016

By Marietta Canty

A paper is presented in which an innovative biological process is described for the treatment of cyanide-, metals-, and nitrate-contaminated mine process water. The technology was tested for its ability to detoxify cyanide and nitrate and immobilize metals in wastewater from agitation cyanide leaching. A pilot-scale demonstration is described in which a pilot plant was constructed to demonstrate the technology on a mine process waste stream at a mine in Nevada. The demonstration was performed Jointly under the Mine Waste Technology Program (MWTP), which is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered by the U.S. Department of Energy's (DOE) Western Environmental Technology Office (WETO) and the Superfund Innovative Technology Evaluation (SITE) Demonstration Program under Interagency Agreement Number DW89938513-0 I-0. MSE Technology Applications, Inc. (MSE) located in Butte. Montana, was the contractor responsible for conducting the project, and Pintail Systems, Inc., of Aurora. Colorado, was the technology provider. The pilot-scale unit was field-tested at the Echo Bay McCoy/Cove Mine southwest of Battle Mountain, Nevada. The biotreatment process was considered to be successful in destroying cyanide in the mine process water. The process was also determined to be effective in removing metals. The pH was consistently neutralized, and nitrates were successfully removed from the mine process water. As a result of conducting these pilot-scale tests, the biotreatment process was concluded to be an innovative, cost-effective alternative for the treatment of mining wastewaters.

Jan 1, 1998