Search Documents

By Lv Guozhi, Niu Liping, Liu Yan, Zhang Zhiqi, He Jicheng, Zhang Ting’an, Dou Zhihe

"CuCr alloy can be extensively used as contact materials in integrated circuit, electrodes, electric contact and high strength conductor. We proposed thermit reduction-electroslag remelting method of preparing the large scale CuCr alloy. But there are pores and oxide inclusions in CuCr alloy prepared by thermit reduction process. This paper studied mainly the effects of ratio of reactant and additive on the inclusion type and their occurrences in CuCr alloy. The slags and CuCr alloy were characterized respectively by XRD and SEM. The results show that when the additive is Na3AlF6, the slag consist of Al2O3 and Cr. When the additive is CaF2, the slag consist of Al2O3, Cr, CaF2 and CaAl4O7. The inclusions in CuCr alloy are mainly Al2O3 and pores which disperse in Cu-rich zone and Cu-Cr phase interface. When 5% CaF2 and 5% KClO3 are added, there are fewer pores and inclusions, and the more better microstructure.1 IntroduceCuCr alloy is the contact terminal material with an eximious properties[1,2], which gradually replaces CuBi alloy becoming the first choice for contact terminal material in the medium and high power vacuum switch after the 1970s. The traditional preparation methods of CuCr alloy mainly contain powder metallurgy, infiltration process and vacuum electric arc melting methods. But the above methods exist some shortcomings, such as poor product quality, high cost of production, processes complex ect[3-9]. CuCr alloy is made by the thermit reduction self-propagating method, which uses CuO, Cr2O3 and Al as raw material to get the high-temperature melt, and then casts to manufacture CuCr alloy ingot, which response equation follows as:"

Jan 1, 2012

By Philip L. Sibrell

A new process utilizing pulsed fluidized limestone beds was tested for the remediation of acid mine drainage at the Friendship Hill National Historic Site, in southwestern Pennsylvania. A 230 liter-per-minute treatment system was constructed and operated over a fourteen-month period from June 2000 through September 2001. Over this period of time, 50,000 metric tons of limestone were used to treat 50 million liters of water. The influent water pH was 2.5 and acidity was 1000 mg/L as CaCO3. Despite the high potential for armoring at the site, effluent pH during normal plant operation ranged from 5.7 to 7.8 and averaged 6.8. As a result of the high influent acidity, sufficient CO2 was generated and recycled to provide a net alkaline discharge with about 50 mg/L as CaCO3 alkalinity. Additions of commercial CO2 increased effluent alkalinity to as high as 300 mg/L, and could be a useful process management tool for transient high flows or acidities. Metal removal rates were 95% for aluminum (60 mg/L in influent), 50 to 90% for iron (Fe), depending on the ratio of ferrous to ferric iron, which varied seasonally (200 mg/L in influent), and <10% of manganese (Mn) (10 mg/L in influent). Ferrous iron and Mn removal was incomplete because of the high pH required for precipitation of these species. Iron removal could be improved by increased aeration following neutralization, and Mn removal could be effected by a post treatment passive settling/oxidation pond. Metal hydroxide sludges were settled in settling tanks, and then hauled from the site for aesthetic purposes. Over 450 metric tons of sludge were removed from the water over the life of the project. The dried sludge was tested by the Toxicity Characteristics Leaching Protocol (TCLP) and was found to be non-hazardous. Treatment costs were $43,000 per year and $1.08 per m3, but could be decreased to $22,000 and $0.51 per m3 by decreasing labor use and by on-site sludge handling. These results confirm the utility of the new process in treatment of acid impaired waters that were previously not amenable to low cost limestone treatment.

Jan 1, 2003

By Xiangwen Wang

Electrochemical measurements associated with the electrowinning of lead metal from concentrated brine (NaCI) - lead chloride (PbCI,) electrolytes at temperatures in the range 328 to 353°K (55 - 80°C) were conducted. The electrodeposition of lead metal onto a lead rotating-disk electrode may be described by the electrodic reaction: {PbCl 4 2 + 2e- = Pb° + 4Cl-} The deposition-overpotential requirements are low (approximately 41mV per decade of current density - Am+), with a corresponding high exchange current (approximately 0.018 A.cm2). The diffusion coefficient of the electroactive PbC142- species in a 3.5 NaCl electrolyte at 353°K was insensitive to the total PbCI, concentration (0.01 to 0.1M), and its value was found to be (1.21*0.1)~10-5 cm2Is with a temperature-sensitivity coefficient (E,/R) of approximately 1.98x103K-1 (328OK(T<353OK).

Jan 1, 1993

By H. Ikeda

The new Onahama N0.3 tankhouse was put into operation early in 1973. This new tankhouse, which has a capacity of 90,000 metric ton cathode per year, is distinct in many important respects from conventional tankhouses. The major objectives in design were to simplify the construction and ope- ration for reduction of the costs for labor, interest and depreciation and also to reduce the copper inventory in the tankhouse by the use of conti- nuously-cast anodes. As a result, the investment cost was decreased by approximately 30% and the inventory cost by approximately 600, while the production per unit area of the tankhouse was increased by 80 - 100% as compared with the existing conventional-type tankhouses at Onahama. By abolition of cell inspection and maximum mechanization of materials handling the labor cost was decreased by as much as 80%. On the other hand, the new system has some disadvantages, such as increase in anode scrap ratio and increased cost of anode casting. The No.3 tankhouse system is, however, still at its starting point, while conventional methods have been continuously improved over the past years of operation. It is expected that the innovational ideas behind this system will serve as bases for a more efficient electrolytic refining system in future.

Jan 1, 1976

By W. G. Davenport

Chapter 4 examined Inco (oxygen) flash smelting of pure chalcopyrite concentrate. It showed that the oxygen and flux requirements for auto thermal smelting are readily determined by a matrix calculation. This chapter extends this matrix approach by applying it to a multi-mineral concentrate.

Jan 1, 2001

By H. H. Kellogg

The thermochemical properties of molten solutions in the binaries Cu-Bi, Cu-Sb and Bi-Sb, as well as the ternary Cu-Bi-Sb, have been correlated and described in mathematical form by use of the associated species concept combined with the three-suffix Margules equations to account for the non-idea 1 behavior of the solution species. Agreement of the correlations with experimental data is excellent (relative deviation of less than 2.5% in the values of the activity coefficients) in most cases. The correlations are applicable over the entire composition range of each system, and in the temperature range 700°-1250°C.

Jan 1, 1985

By Zhuo Sheng

We have designed a high-temperature Raman micro-furnace and cell that is suited for the electrochemical process study of the NO3 − in molten NaNO3– KNO3 (fraction of NaNO3 50 wt%) salt. During the cycle voltammetry and constant potential electrolysis process, the Raman laser beam was focused near the electrode; subsequently, the Raman spectra are obtained and the reduction process of NO3 − is analyzed. In the CV cathodic scan process, the new peak attributed to the ν1 mode of NO2 − emerges, and the peaks assigned to superoxide ions (O2 −) and peroxide ions (O2 2−) are not found. In the constant electrolysis process, the peaks at 1130 and 800 cm−1 appear when the potentials are between −2.0 V and −3.2 V (vs. Pt). The results show that when the NO3 − is reduced in molten the NaNO3–KNO3 mixtures, the reduction product O2− cannot stably exist, and O2− will react with NO3 − to form of superoxide ions (O2 −) and peroxide ions (O2 2−).

By Frederick W. DeVries

The author was invited by "60 Minutes Australia" to provide on-site technical background on cyanide, mining, and the environment, in their investigation of the January 30, 2000, spill at the Aurul gold-recovery site in Baia Mare, Romania. Some remarks on the incident ?and its implications surround a showing of the fourteen-minute telecast. The thrust of the TV reporter was that aspects of the dam implied the owners&apos; use of standards Jess than would have been met for installations in technologically more advanced locations (like Australia). As a result, the public-relations impact is one of embarrassment for the world mining industry.

Jan 1, 1998

By Xu-ling Chen, Qian Li, Yong-bin Yang, Zhao Jing, Tao Jiang, Guang-hui Li

"It is generally known that alkali metals are harmful to blast furnace production resulting in aggravating RDI of sinters, abnormal expansion of pellets, deteriorating blast furnace lining, etc. Sinters regarded as dominating burden of blast furnace are determined as the main source of alkali metals. In this study, the removal behavior of potassium and sodium oxides by pre-reduction sintering during the sintering process was studied. The removal ratio ofK20 and Na20 was greatly influenced by coke powder content, carbon species, coke powder adding ways, additive and so on. Under the conditions of carbon rate 12% and 5% dosage of CO supplied in the sintering process, the corresponding removal ratio ofK20, Na20 was 69.00% and 32.79%, and metallization ratio could reach 4.65%. This technology provided a novel process for reducing the content of alkali metals in sinters and dramatically improving the quality of blast furnace burden.IntroductionSinter is the main iron-bearing charge of blast furnace for iron-making in China, making up about 80% of the total burden; therefore, its quality has a significant influence on the quality of pig iron and blast furnace operation. Research and practice of numerous years prove that potassium and sodium coming from ores are brought into blast furnace and upgraded, which is one of the essential reasons that lead to blast furnace nodulation and influences its strength. Currently, effective flow sheet to remove potassium and sodium is weak magnetic separation-intensive magnetic separation-flotation [l], while iron ore concentrate is still ofhigh levels of potassium and sodium. As sintering process is also not effective to remove potassium and sodium, blast furnace in China is of high alkali burden, e.g. it reaches 5.6-6.2kg/tFe in Baotou iron making plant, which is greater than international tolerated level of2.55kgltFe [l]."

Jan 1, 2013

By Sylvain Gouttebroze, Mohammed M'Hamdi

In a previous work, a small scale Bridgman furnace has been used to study silicon bi-grain crystallization at different cooling rate. This work expands the analysis by studying the mechanical interaction between the crucible and ingot during the solidification and cooling. The thermal model is based on a 2D-axisymetric heat-transfer model. The flux histories are then transferred to the ingot-crucible 3D-model. Anisotropic Elastic and Crystal Plasticity model are used to model the silicon deformation. Four different assumptions are applied to model the mechanical contact crucible-ingot and three grain misorientations are considered. The results show the strong impact of the alumina crucible contraction on the stresses and deformations in the silicon ingot.

Jan 1, 2015

By Dan A. Mackie

Cyanide leaching operations have taken a beating from the press and the public at large for its seemingly haphazard approach to control of cyanide solutions and containment of tailings. Major spills in Colorado, Guyana, Spain, and more recently, Romania, have highlighted what had already been perceived to be a bad scene. Citizen initiatives and legislative actions are increasing. Whether these indictments are justified or not will not be debated in this paper. What this paper presents is that the technology to avoid these disasters and future ones has been around for more than ten years but has been ignored by the industry, despite demonstrated&apos; cost effectiveness. It is time for miners to wakeup, and use emerging, instead of old, technologies.

Jan 1, 1998

By Zhi-biao Yin

Copper smelter flue dusts often cannot be directly recycled to the smelting process and accumulate as hazardous wastes requiring environmentally acceptable disposal. Because of the limited amount of flue dust, a separate copper extraction process must be simple and require-a small plant investment. A flue dust process has been developed, consisting of the following steps: (1) roasting a pelletized mixture of hydrated lime and flue dust to fix arsenic and sulfur as insoluble calcium salts, (2) heap leaching the roasted pellets with a buffered ammonia/ammonium salt solution to extract copper as an ammine complex in a lined cell that is the final repository of the leached pellets, and (3) boiling ammonia from the lixiviant to precipitate copper. Condensed ammonia and the filtered solution are returned to leaching. Heap leaching in the final repository cell lowers the capital investment significantly compared with competing extraction processes. Chemistry with respect to arsenic, sulfur and copper is discussed.

Jan 1, 1992

By Baojun Zhao, Zhixiang Cui, Zhi Wang

"Bottom blown oxygen copper smelting process has been developed in Dongying, China by Dongying Fangyuan Nonferrous Metals Co., Ltd. in commercial scale. This is the first modem copper smelting technology developed in China with the advantages of high oxygen enrichment, low temperature and autothermal operation. Production capacity of more than 100,000 tonnes per year of copper has been achieved through a single bottom blown oxygen furnace with instantaneous feed rates reaching up to 90 t/h. The main features of the bottom blowing smelting process are that high grade matte (up to 72 wt% Cu) can be produced at relatively low temperatures with 2-3 wt% Cu remaining in the smelting slag. Analyses of quenched smelting slag show that significant amount of magnetite crystals are present in the slags at operating temperature which indicates that the operating temperature was much lower than the liquidus temperature of the slag. After four years operation this new technology has shown great potential for expanding production capability and energy saving. Process development continues on the first commercial scale bottom blown furnace at Dongying Fangyuan Nonferrous Metals and a larger bottom blown smelting furnace is under construction.IntroductionFlash and bath smelting technologies are the major processes used in modem copper making industry [l]. Ausmelt/Isasmelt using top blown and Noranda/Teniente using side blown are typical and common bath smelting technologies. In 1980s-1990s Hunan Shuikoshan Mineral Bureau, jointly with China Nonferrous Engineering and Research Institute (now China Enfi Engineering Corp.), developed the concepts of the bottom blown oxygen processes for both lead and copper smelting [2]. After the pilot test on 3000 ton copper per year scale in 1991, it was not progressed to industrial scope."

Jan 1, 2013

By Kiichiro Hayashi

"Indonesia is one of the world leaders in palm oil production. Palm oil industry is an industry to be considered when it comes to environmental impacts. This paper utilizes three step approaches. First, a material flow analysis of palm oil related industry was conducted in Indonesia. Second, a factory visit survey was conducted for getting information on environmental impacts of plantation and CPO mills. Third, a LCA study was made for a model Indonesian CPO mill in several bio-waste treatment options. Main findings were that, first; over 70% of FFB was bio-wastes generated from CPO mills. Second, some mills introduced a zero emission bio-waste policy. However, untreated bio-wastes in the zero emission policy, such as, CH4 from POME ponds, may have potential to reduce more impacts on the environment. Introduction Indonesia is one of the world leaders in palm oil production with approximately 12.4 million tons of crude palm oil (CPO) production in 2005 and with the plantation area 5.6 million ha spreading out in 19 provinces [10]. The expansion of palm oil cultivation in Indonesia and its export oriented industry heavily relies on the strong world market demand for food. Currently, there are 320 CPO industries in Indonesia [10]. These include plantations and palm oil related factories. Among them, there are six biggest players in CPO business in Indonesia: PT. Perkebunan Nusantara (PTPN) consisting of 9 PTPN, Sinar Mas, Raja Garuda Mas, Astra Agro Lestari, Minamas Plantation and Indofood. They are managing more than 50% of plantation estate in Indonesia and are leading the Indonesian palm oil business.Palm oil industry is an industry to be considered when it comes to environmental impacts. Unfortunately, there is not so much available information related to the performance of each CPO on environmental impacts. There are reports which provide information on environmental impacts of CPO mills in South East Asian countries, but are limited to, for instance, Thailand’s cases [4 and 5] and Malaysia’s cases [1, 3, 6, 7, 9, 11 and 12]. On the other hand, similar studies on the Indonesian’s case are not well established in academic literatures. And also there is limitation on Indonesian palm oil industrial information from plantation to consumption and disposal in academic articles. There is no literature related to material flow analysis focusing on the whole Indonesian palm oil related industry. One way to describe and present the environmental impacts is through a life cycle assessment (LCA). The LCA could be used to estimate the impacts of CPO production including the stages of plantation, transportation and milling [5, 8 and 11]. However, studies on Indonesian CPO production process were not well established in academic articles. The purpose of this paper is thus to clarify environmental impacts of palm oil industry in Indonesia especially by focusing on plantation and CPO mills with consideration to various bio-waste treatments."

Jan 1, 2008

By John Norton

"This presentation will cover the physical properties of waste heat recovery. It is a two part presentation. The first deals with actually recovering the heat with new state of the art heat exchangers and applying that heat to the furnace combustion and the second part will cover what other processes you can enhance with this ""free"" heat. It will also talk about converting it to steam, hot air or electricity to be used or sold back to the utility company. The economics of various schemes will be reviewed. A brief discussion on State and Federal grants and subsidies will be presented.IntroductionThere are large quantities of wasted heat in the usual aluminum melting process. And, there are several techniques for reducing and/or using some of that wasted heat as you have seen. Any technique that can make use of wasted heat is a form of recovery. This can range from simply preheating aluminum billets prior to melting, to more complicated processes like air-to-air heat exchangers using the boiling and condensing characteristics of special fluids in “heat pipes.” The objective of this type energy recovery process is to move the wasted heat from the hot and dirty exhaust gas stream into some useful process.Waste Heat Recovery in the Aluminum Melting Furnace.There are considerations, of course:1) What might the value be of the recovered energy?2) Can the recovered energy be used within the process? Within the plant? Or by theneighbors?3) What is the capital cost?4) Is the recovery process complicated?5) Will it take additional staff?6) Will it cause additional downtime on the melting line?7) Will the operations staff need to be licensed?Ideally, the process will be simple and inexpensive, the recovered energy will be very valuable, and the whole effort will cause little distraction to the aluminum melting process itself. These would be ideal."

Jan 1, 2011

By Xiao-hui Fan, Li-shun Yuan, Xu-ling Chen, Wei Lv, Min Gan, Yi Wang

"As the amount of ferrous scrap increases every year, it becomes more and more urgent to deal with this iron-bearing resource properly. This paper puts forward a method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing), and these cold-bonded pellets can be used as coolant in a converter. The influence on the pellets qualities by using different kinds of chloride as rust agents is studied, and results show that the strength of cold-bonded pellets increases significantly by using a combination of the three kinds of chloride -NaCl,MgClz,FeCh, their best dosages are 1.2%, 0.2%, 0.1% respectively. Other iron-bearing materials also have an effect upon the pellets strength, by adding 5% iron powder and maintaining for 48h, the compressive strength of the clumps surpass 2500N/A, dropping strength surpass 4 times/ A, and 10% iron slag or 20% steel slag can replace 5% iron powder while obtaining the comparative quality. The influence of different ratios of three ferrous scrap (converter mud, iron scale and dust) is further studied, and results show that when the ratio is 30% : 30% : 40%, the pellet strength reaches the maximum. After maintaining for 24~48h, the clumps can meet the mechanical as well as the physical-chemical requirements as BOF steelmaking refrigerant.IntroductionGreat amounts of converter mud, dust and iron scale are produced in steel production process. These materials are of great values, and their accumulation not only leads to environmental pollution, but also wastes the precious resources, which restricts the sustainable development of the steel industry [1,2] The main approach at present to dealing with the ferrous scrap is to add them into sintering. But in this way, the utilization factor of sintering and the quality of sinter decline while the energy consumption increases [3].Therefore, more advanced and efficient technology is needed to make the best of these iron resources. Cold consolidation of ferrous scrap is a simple process that has many advantages such as less investment, quicker effect, lower energy and lower cost [4-5] But the conventional maintaining period is too long, usually up to four-six weeks, and the pellet strength is low. Therefore, the key points of the cold-bonded pelletizing are to develop a new adhesive [4,5] to shorten the natural maintenance cycle and to improve the strength of the pellets. A method on resource-oriented utilization of ferrous scrap (cold-bonded pelletizing) is brought forward, and these cold-bonded pellets can be used as coolant in converter. After maintaining for 48h, these cold-bonded pellets can satisfy the mechanical requirements to replace the converter coolant [6]."

Jan 1, 2013

By Sugui Tian

By means of the T6 treatment, the measurement of creep curves and microstructure observation, the influence of T6 heat treatment on the microstructure and creep properties of Ti-6Al-4V alloy is investigated. Results show that the microstructure of the forged alloy consists of the banded-like a phase and networks b phase. After sub-temperture T6 treated, the microstructure of alloy consist of the block a phase and ?networks basket? structure. Under the conditions of the applied stress of 575 MPa at 4000C, the forged alloy displays a lower creep lifetimes, after T6 treated the creep lifetimes of the alloy is enhanced to 548 h from 66 h, which is attributed to the formation of the network basket structure in which the needle-like phase are dispersedly distributed. As creep goes on, the denser dislocations in the a phase are concentrated to occur the dynamic recrystallization for refining grain. which is a main reason of the alloy displaying a better creep lifetimes and plasticity. Thereinto, the creep mechanism of the forged alloy is thought to be the slip of the straight <a> and <a+c> dislocation are activated on the prismatic planes and pyramidal planes, while the creep mechanism of T6 treated alloy is that wave-like <a+c> dislocations are activated on the pyramidal planes.

Jan 1, 2009

By Klaus Gamweger

"This paper introduces an innovative solution to open and close the tap hole of different furnace types in the copper industry with a slide gate system. Two plates with defined drilled holes are slid against each other, which enables effective starting and stopping of the copper flow as well as throttling. Typically, the copper is poured via a tap hole into a launder system by rotating the furnace into an appropriate position. Control of the casting rate is also performed in this manner. Or, in case of stationary furnaces the tap hole is opened by oxygen lancing and closed manually with a clay- or copper-cone. These procedures show a lot of disadvantages including splashing, oxygen pick-up, and energy losses as well as a severe danger for the working staff. All these problems can be overcome with an appropriate slide gate system.IntroductionThe control of the casting rate of a copper anode furnace usually is performed by rotating the furnace into an appropriate position. This implies that the taping starts with the tap hole at a very high position. Copper splashing and an uncontrolled oxygen pick up are - with several more disadvantages - the consequences. RHI AG has developed an innovative solution for copper applications to open and close the tap hole with a slide gate system which allows also an accurate control of the flow rate. By using this system it is possible to start the casting procedure with the tap hole at the deepest position, directly above the launder. This paper presents this new slide gate system in detail and shows the advantages in production and safety issues."

Jan 1, 2012

By Alexander I. Raitchenko

"Although one takes into account only thermal expansion usually at analysis of convection onset, the essential factors include magnetic and electric fields. If Lorentz-force originating from intercrossed electric and magnetic fields' action is directed downwards its effect strengthens gravitational action, and value of critical Rayleigh number (limit value for convection onset) must decrease; increasing of critical Rayleigh number should be observed in case of Lorentz-force directed upwards. Extent of such an influence is determined by relation of Lorentz-force to hydrostatic head in gravitational field. Competition between electromagnetic force due to nonuniformity of electroconductivity (on account of its temperature dependence) and electromagnetic buoyancy force may have ambiguous effect: both increase or decrease of critical Rayleigh numbers. Proposed conception is applicable to analysis of situations in liquid conductors and conductive gases.IntroductionStatic or dynamic situations in fluid media are determined besides properties of these media by a variety of external influences. However one correlate~ the onset of the convection and its development with influences of the minimum quantity of external causes frequently. Most known and usual factors are the gravitational and temperature fields. The number of processes includes heat generation in media volume, and theoretical analysis in these cases takes into account this interior heating together with boundary temperature conditions. But explanation of many natural and technical events is not complete and cogent within limits of thermo-gravitational terms. The whole complex of acting factors which influence convective processes in techniques and nature is greater in many cases. In particular the action of · electromagnetic nature often has not less importance than gravitation one. Stability or instability of a current layer in the plasma must be determined by non-uniformity of electroconductivity owing to non-uniformity of temperature [1]. The presence of Joule dissipation in the plasma through which the electric current flows stipulates initiation of origin of overheated instability [2]. It is known that electroconductivity of arc in the boundary zone changes sharply with radial distance [3], and this must influence its stability essentially. If the intercrossed electric current and magnetic field begin to act on an electroconductive fluid besides the non-uniform temperature field and the gravity, the conditions for the onset of the convection change radi- . cally: both the temperature field and their solutions have to be changed also. The analysis of equilibrium single-time correlation functions of fluctuations must be employed for situations with enlarged number of factors as this was in case for the Rayleigh-Benard problem where the object is a horizontal layer of liquid. This can be carried out by taking into account the detached forces' correlations [ 4, 5]"

Jan 1, 1999

By Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems are less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra&apos;s continuous countercurrent ion exchange technology (CCIXTM) and fixed film biological reactor, Denite°. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1994