Search Documents

By Akira Nishikawa

During the twentieth century, the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Sarah Beutner Mavrogenes

The mineralogy of three slags from a domestic secondary copper refinery were studied by applied mineralogical techniques to determine the: 1) phases present, 2) phase chemistry, 3) phase abundance, 4) associations, 5) crystalline habit, 6) grain size, 7)microtextures, and 8) causes for certain metallurgical problems, such as metal losses to the slags. The slags were produced by skimming the bath prior to melt-down to allow heat from the flame to reach the bath. The first slag is highly viscous and all three slags contain a large amount of copper. The "first slag", which is skimmed prior to treatment of the bath with fluxes, contains metallic copper, cuprite, delafossite, magnetite, Mg-hercynite, common spinel-chromite solid solution, picrochromite-chromite solid solution, common spinel-picrochromite solid soiution, gahnite, cassiterite, silica-rich glass, and corundum. Its abundant solid refractory phases make the slag difficult to skim. The "soda-rich slag", skimmed after the treatment of the bath with sodium carbonate flux, contains cuprite, delafossite, magnetite, cassiterite, Na-Al-silicate, and Na-Al-Ca-silicate. It contains less metallic copper than the first slag and lacks the refractory minerals. The "phosphorus-rich slag", skimmed after treatment of the bath with a copper phosphide flUX, contains metallic copper, cuprite, delafossite, berlinite, cassiterite, silica, apatite, Cu-Fe-rich apatite, copper phosphate, Cu-Fe-phosphate, and a Pb-phosphate. In contrast to the above three copper-rich slags, recent charges have produced a silver-copper-rich slag. The "silver-rich slag", skimmed after the treatment of the bath with a copper phosphor ide-borax flux, contains, cassiterite, delafossite, cuprite, a Na-Al-silicate, magnetite, metallic copper, MgO, common spinel-chromite solid solution, and wollastonite. Silver ranging from 0.05 to 2.02% was found by atomic absorption and inductively coupled plasma spectrometry analyses in the metallic copper phase.

Jan 1, 1989

By Esher Hsu

On July 5, 1997, Environmental Protection Administration of Taiwan publicized the recycling regulation of waste home appliances that include four items, namely, television, refrigerator, washing machine, and air conditioner. It is believed that this regulation pioneers the law enforcement of waste home appliances in the world. The objective of this study is to provide helpful base for amending recycling rates of waste home appliances. This study investigates the collection and recycling costs of waste home appliances in accordance with these newly established routes and facilities, respectively. Cost survey was conducted among collectors and recycling plants of waste home appliances; consequently, the collection and recycling costs were analyzed, correspondingly. Results provide some suggestions regarding recycling route, recycling system, recycling rates paid by manufactures and importers, recycling subsidies to collectors and recyclers. Those suggestions may provide useful policy implications to EPA for the future decision-making regarding the recycling of waste home appliances.

Jan 1, 2003

By Bradford C. Wesstrom, Omar Araujo

"Impurities from an electrolytic refinery are typically extracted from the electrolyte utilizing conventional electrowinning cells. These cells are arranged in series with cascading solution flow and are commonly referred to as liberator cells. The Freeport McMoRan Copper & Gold El Paso Refinery has optimized the removal of arsenic in cascading liberator cells by utilizing two separate feed solutions. The primary feed solution is recycled liberator electrolyte and the secondary feed solution is ""neat"" tank house electrolyte. The secondary feed solution is added based on the voltage response across the individual cells utilizing independent variable frequency drive (VFD) pumps. When the voltage across a cell changes, a signal is sent to the VFD pump to maintain a cell voltage of 1.98 volts. By maintaining this voltage the copper content in each cell exits at 2-4 grams per liter. This safely optimizes the arsenic removal as copper arsenides on the liberator cathodes.IntroductionDuring the electrolytic refining of copper, impurities from the copper anode report both to the bottom of the electrolytic refining cell as slimes and to the electrolyte. The impurities which enter the electrolyte are arsenic, antimony, bismuth and nickel. The impurities that report to the electrolyte during the electrolysis process gradually increase. As these impurities increase, they are incorporated into the refined copper cathode. There are many processes that have been used to remove these impurities from refinery electrolytes. Some of them are listed as follows: solvent extraction, ion exchange, hydrogen sulfide reduction, bioreactor, adsorption onto a low - solubility metal-oxide hydrate, adsorption onto activated carbon and EMEW cells. The conventional process used by the copper refining industry for controlling the level of impurities in electrolyte involves multistage electrolytic cascading liberator cells. In these cascading liberator cells copper, arsenic, antimony and bismuth are removed as various mixed deposits from the electrolyte. Removal of these impurities is achieved through an increase in voltage resulting from the depletion of copper in the electrolyte through electrowinning. With this higher voltage, the Group Vb elements, arsenic, antimony and bismuth are deposited on the copper cathode and report as slimes to the bottom of the cells. Nickel is removed in a subsequent process."

Jan 1, 2012

By Lucas L. da Costa, Sergio N. Monteiro, Romulo L. Loiola, Tammy G. Rodrigues Portela

"The fibers extracted from the petiole of the buriti palm tree are relatively strong as compared to other lignocelluloses fibers, with a potential for composite reinforcement. In this work, polyester matrix composites incorporated with these fibers were investigated for their flexural behavior. Specimens with up to 40% in volume of continuous and aligned buriti petiole fibers were bendtested until rupture. The results showed an increase in both the composite mechanical strength and the stiffness with incorporation of these fibers. A fractograph analysis by SEM disclosed a moderate adhesion mechanism between the buriti petiole fiber and the polyester matrix. This mechanism is apparently responsible for the improved performance of the composites.IntroductionIn recent years, the substitution of energy-intensive synthetic materials for natural ones is being considered in many industrial sectors including automobile, packing and textile [1]. A typical case is that of natural fibers, mainly those obtained from cellulose-based plants also known as lignocelluloses fibers. They have being investigated in the past two decades, aiming to replace synthetic fibers, particularly the glass fiber, commonly used as polymer composite reinforcement [2-8]. From the engineering point of view, lignocellulosic fibers present today important environmental, economical, societal and technological advantages already discussed [7-8]. Moreover, several lignocellulosic fibers are known since the beginning of our civilization and still cultivated or naturally extracted all over temperate and tropical regions of the world. According to Kalia et al [1 ], these fibers can be classified by their origin, as shown in Table 1."

Jan 1, 2011

By Metehan Erdogan, Ishak Karakaya, Fuat Erden, Emre Ergül

"The FFC Cambridge process was suggested as a promising Si production technique for the expanding solar energy industry. Direct electrochemical reduction of bulk SiO2 plates and porous SiO2 pellets in molten CaCl2-NaCl salt mixture were investigated at 750°C by applying 2.8 V potential difference. The produced Si powder was brown and found to be contaminated by the Ni and stainless steel plates used as the cathode contacting materials. The reduction rates of the bulk SiO2 plates and porous SiO2 pellets were compared from variations of current and accumulative electrical charge that passed through the cell during the electrochemical reduction. The amorphous bulk SiO2 plates were reduced slightly faster than porous pellets of crystalline SiO2. The overall reduction potential of SiO2 pellets against the graphite anode at 750°C in molten CaCl2-NaCl salt mixture was determined as 2.3 V by cyclic voltammetry. This potential was supported by calculations.IntroductionMetallurgical grade Si cannot be directly used in electronic industry and some intermediate steps are required to produce industrial solar grade silicon (SOG-Si). A promising alternative solar grade silicon production technique is the FFC Cambridge Process [1]. Production of Si by electrochemical reduction of SiO2 at 850oC in molten CaCl2 electrolyte was first studied by Nohira et.al. [2]. In their study; Si formation was observed on bulk SiO2 cathodes after 1 hour of electrolysis. Complete electrochemical reduction of porous SiO2 pellets was first reported by Jin and his coworkers [3]. The mechanism of electrochemical reduction of SiO2 to Si in molten CaCl2 was explained in another study [4]. Reduction rates of bulk SiO2 and porous SiO2 pellets were also compared previously and it was found that reduction rates for bulk plates were higher [5]. Furthermore, it was reported that mixing Si into porous SiO2 pellet increased the reduction rate [5]. Mo [2, 4-7], Ni [3, 8, 9] or Si [6] were used as cathode contacting materials in various studies. Yasuda et. al. [6] produced Si with 99.80 % purity using Si plates as cathode contacting material to reduce metal contamination."

Jan 1, 2012

By Matthew D. Andriese, Jiann-Yang Hwang, Zhiwei Peng

"It has been demonstrated that metallic-bearing minerals are physically liberated from host rock when exposed to microwave (MW) energy. The metallic minerals are iron sulfides and spinel oxide minerals contained in peridotite rock. Experimental evidence has shown ore particles readily couple with MW energy at 2.45 GHz, 1000 W resulting in rapid heating. Thermal stresses are generated by highly absorbing metallic-bearing minerals resulting in cracking and embrittlement of ore particles that assists in crushing and grinding processes. The liberated metallic-bearing minerals are shown to report to coarser size fractions as a result of MW exposure.IntroductionComminution of ore material during beneficiation is a large energy expenditure for the mineral processing industry. Crushing and grinding operations alone consume 50-70% amount of energy used in mineral processing [1]. Size reduction becomes increasingly difficult with decreasing particle size making grinding the most energy-intensive step of comminution. The aim of comminution is to maximize liberation of economically valuable minerals from the host rock [2]. Overall, the less material that needs to be handled, then grinded, to create a useful product for hydro/pyro metallurgical processes will achieve the greatest reduction of energy.Much of the scientific interest for use of microwave (MW) energy in mineral processing has been for improved hydro/pyro metallurgical techniques [3-6]. Early authors have employed MW energy for improved grinding of ore particles but most conclude the energy savings do not justify the energy input [7-9]. The effectiveness of MW assisted grinding is dependent on the ore mineralogy and the absorptive properties of minerals contained within it. Ore containing magnetic minerals should prove successful with MW assisted breakage from highly absorptive properties."

Jan 1, 2012

By S. S. Chabot, S. E. James

A recent survey of CEOs from major steel companies worldwide revealed the importance of recycling zinc units from EAF dust, mill scale, blast furnace dust, and other zinc containing streams in their plants. Many processes were developed and installed in response to this challenge. The most successful approach involves the production of a crude zinc oxide and selling it to primary zinc producers to recover the metal value. The problem with this process is the high concentration of halides in the crude oxide. This type of material cannot be processed directly in an electrolytic zinc plant because of corrosion problems it will cause in electrolysis. In 1999, BRZ installed a zinc oxide receiving and washing plant to minimize the impact of halides to its circuit. A description of the washing plant and initial operating results are included.

Jan 1, 2000

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By E. N. Mounsey

Ausmelt Technology was selected by Bindura Nickel Corporation (BNC) as the basis for a new copper circuit to process nickel plant copper leach residue to blister, anode and finally cathode copper and recover PGM values at the Bindura Smelter Refinery (BSR). The process selected, based on Ausmelt Technology to smelt and convert the residue to matte and blister copper and produce a discard slag, is novel incorporating smelting, converting and slag reduction process steps in a single Ausmelt vessel. The process demands a high quality blister copper product with low levels of arsenic and nickel. This paper reviews the project and the initial operational results to the end of 1997 of the Ausmelt Top Submerged Lancing (TSL) smelter and discusses the implications for the wider TSL converter market.

Jan 1, 1998

By Mim Li, Huimin Lu, Lisha Yang

"CuInS2 thin films solar cells have drawn much attention for their low-cost, stability and high conversion efficiency. The electrodeposition of Cu-In precursor films, as the first step in making CuinS2 solar cells electrochemically in the air-and water-stable ionic liquid based on choline chloride/urea eutectic mixture has been investigated at constant potential. Compared with aqueous electrolytes, the large electrochemical window as well as the high thermal stability of this ionic liquid allow the direct electrodeposition of Cu-In precursor films. Then the precursor films were sulfuretted in a tube furnace at different sulfurization temperatures to optimize the films properties. The films obtained were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), energy dispersive spectroscopy (EDS).IntroductionCuInS2 is one of the most prospective absorber materials for low cost thin film solar cells, with a high conversion efficiency that exceeds 32% in terms of theory and nearly 13% in laboratory level [1-2]. In addition to its long-term stability, CuinS2 has a band gap energy Eg ranging from 1.3 to 1.55 eV and an optimal optical absorption coefficient reaching 105cm-1 [3-4]. CuinS2 thin films have been prepared by several methods such as spray pyrolysis [5-6], r.f.sputtering [7], vacuum evaporation [8-9] and electrodeposition. Comparing with vacuum methods, electrodeposition has lots of advantages such as less energy consumption, preparation big area thin film, stable system and enabling cheaper films.The electrodeposition of most technologically important metals has been shown to be possible from a wide range of ionic liquids. These ionic liquids are currently applied in a wide variety area. It is reported that the cell efficiency of chalcopyrite absorber layer (CIS, CISeS, and CIGS) via an electrodeposition route in laboratory condition has reached 11.3% [10]. Copper and indium alloy film is regarded as important precursor for the production of compound semiconductors with sulfur. The electrodeposition of the alloy film from room temperature ionic liquid (RTIL) has not been widely investigated. Only few alloy films, such as ZnTe, CdTe, GaAs and AlSb have been electrodeposited."

Jan 1, 2011

By Qian Li, Li-chen Hou, Yong-bin Yang, Tao Jiang, Jian-jun Hu, Bing Xu

Extraction of gold from refractory gold concentrates usually requires an oxidation step to remove arsenides、sulphides and carbonaceous matter. In this investigation, the gold concentrates were two-stage roasted under different atmospheres and temperatures. Results indicated that at the first stage, under neutral atmosphere, the removal rate of arsenic increases as the temperature rises. Under the oxidizing atmosphere, with the increase of temperature, arsenic content in the residued calcine increases, in addition, the volatilization of arsenic is also affected by the oxidation of carbon that generated CO, which is advantageous to the decomposition of arsenate decomposition. At the second stage of roasting, it is the higher temperature and stronger oxidizing atmosphere, the faster sulfur and carbon oxidated rate is, but at the same time, the calcine appears the phenomenon of consolidation because of the phase of silicate compounds generate.

Jan 1, 2015

By Biserka Lucheva, Tzonio Tzonev

"A unique DC electric arc rotary furnace with capacity 150 kg has been designed and constructed for the recycling of low-quality scrap and aluminum dross. The main constructive feature of this furnace is that the axially positioned graphite electrodes (cathode and anode) are placed 100 mm away from the rotation axis of the furnace. A specific characteristic of the construction is the possibility one of the electrodes (the anode) apart from moving axially (parallel to the furnace axis) to move at 90° outside the working space. High recovery rate of metal aluminum from aluminum dross (92%) was realized in this furnace. This is the reason for construction of industrial DC electric arc furnace.IntroductionThe consumption of aluminum waste has been rising continuously on a world scale, which is a great stimulus for the development of the technology for aluminum recycling.To recover the aluminum in dross, the conventional recycling process uses salt rotary furnaces heated with a fuel or a gas burner. This treatment process produces a secondary dross containing alumina, salts, impurities and a small amount of aluminum. Molten aluminum is tapped from the furnace and the residue is then dumped from the furnace. It has been the practice to dispose the residue in a landfill. Improvement of this technology, known as the oxy-fuel process, uses a gas burner enriched with oxygen to increase the thermal efficiency [1]. Recent studies show that the most efficient aggregate for recycling of aluminum scrap has turned out to be the rotary tilting furnaces, heated by plasma or electric arc, for which the use of flux is not necessary [2,3].Accordingly, there is a substantial need in the industry for an improved process for recovering free aluminium. It is particularly desirable that such process be cost effective and ecologically safe."

Jan 1, 2008

By Anja Pfennig, Axel Kranzmann, Phillip Zastrow

"Properties of pipe steels for CCS technology require resistance against the geothermal corrosive environment (heat, pressure, salinity of the aquifer, CO2-partial pressure). To predict the reliability of two different injection pipe steels with 13% chromium and 0.46% carbon (1.4034, X46Cr13) as well as 0.20% carbon (1.4021, X20Cr13) steel coupons were heat treated by comparable routines prior to long term corrosion experiment (60°C, 100 bar, artificial brine close to a CCS-site in the Northern German Basin, Germany). In general higher carbon content exhibits better corrosion resistance with respect to corrosion rate, amount of pits and maximum intrusion depth in the case of local corrosion. At 100 bar hardened steels with martensitic microstructure have the lowest corrosion rates with an average of 0.003 mm/a after 2000 h exposure time. At ambient pressure normalized steels show the lowest corrosion rates, indicating that the corrosion is driven by grain boundaries.IntroductionEngineering a geological on-shore saline aquifer CCS-site (CCS Carbon Capture and Storage [1-3]) corrosion of injection pipe steels may become an issue when emission gasses, e.g. from combustion processes of power plants, are compressed into deep geological layers [4-8]. Typically 42CrMo4 (1.7225, AISI 4140) is used for casing, and for injection pipe the steel X46Cr13 (1.4034, AISI 420 C) or X20Cr13 (1.4021, AISI 420 J) is used. Saline formations are the most favorable storage sites in Germany [9], because of their large potential storage volume and their common occurrence. Leakage of CO2 back into the atmosphere may be a problem in saline aquifer storage, especially around the water level within the borehole. Carbon dioxide corrosion may cause failure of pipelines and wells as known from the oil and gas industry [4,6,10,11, 12].From thermal energy production it is known, that the CO2-corrosion is sensitively dependent on alloy composition, contamination of alloy and media, environmental conditions like temperature, CO2 partial pressure, flow conditions and protective corrosion scales [6-8,13- 20]. Considering different environments, aquifer waters and pressures, the analyzed temperature regime between 40 °C to 60 °C is a critical temperature region well known for corrosion processes as shown by Pfennig et al. [21-23] and various other authors [10,24-28] (figure 1). Here a maximum around 4.7 mm/year was found for the pit intrusion depth of 13% Cr steel X46Cr13. Still this may be predicted by the rather conservative Norsok-Model used in the oil and gas industry to calculate surface corrosion rates of carbon steels [29]."

Jan 1, 2014

By Frederico Muylaert Margem, Giulio Rodrigues Altoé, Glenio Daniel, Pedro Amoy Netto, Sergio Neves Monteiro, Maria Carolina Andrade Teles

The environmental concern is creating pressure for the substitution of high energy consumption materials for natural and sustainable ones. Compared to synthetic fibers, natural fibers have shown advantages in technical aspects such as flexibility and toughness. So there is a growing worldwide interest in the use of these fibers. Fique fiber extracted from fique plant, presents some significant characteristic, but until now only few studies on fique fiber were performed. This work aims to make the analysis of the tensile strength of polyester composites reinforced with fique fibers. The fibers were incorporated into the polyester matrix with volume fraction from 0 to 30%. After fracture the specimens were analyzed by a SEM (scanning electron microscope).

Jan 1, 2015

By Z. W. Zhang, Songsong Xu, Jinhui Li, Yun Zou, Yu Zhao

High strength low alloy (HSLA) steels with high strength, high toughness, good corrosion resistance and weldability, can be widely used in shipbuilding, automobile, construction, bridging industry, etc. The microstructure evolution and mechanical properties can be influenced by thermomechanical processing. In this study, themomechanical processing is optimized to control the matrix microstructure and nano-scale precipitates in the matrix simultaneously. It is found that the low-temperature toughness and ductility of the steels are significantly the matrix microstructure during enhancing the strength by introducing the nano-scale precipitates. The effects of alloying elements on the microstructure evolution and nano-scale precipitation are also discussed.

Jan 1, 2016

By Guo Chen, Jin Chen, Jinhui Peng

"In this paper, the methods of life cycle assessment for microwave hot air systems, and the concept of green degree were proposed. Greenness evaluation index, evaluation system and evaluation model of microwave hot air systems were established. Also, life cycle assessment processing based on these ideas was introduced. Analytic hierarchy process and fuzzy decision- making method were utilized to establish and solve the greenness evaluation of assessment model, while the scores of green degree in microwave hot air systems were obtained. The results show that Life cycle assessment can be applied effectively and efficiently to the microwave hot air systems.IntroductionHot air systems are an important industrial operation condition, which is used to provide high temperature air for materials processing. Nowadays, high temperature airs are manufactured by the conventional heating processes, in which some ceramic materials are used as heating materials. However, these processes pollute the environment. Therefore, to explore new method to produce high temperature air with low energy consumption and less environment pollution are necessary.Microwaves are now being used in various technological and scientific fields in order to heat dielectric materials [1]. Microwaves irradiation has been explored in materials processing in recent years [2-3]. The main advantage of using microwave heating is that the treatment time can be considerably reduced, which in many cases represents a reduction in the energy consumption as well. Since there is energy absorption but no heat conduction, the heating is very rapid and highly efficient, resulting in energy savings and the shortened processing time [2, 4]. Compared with conventional heating techniques, the additional advantage of using microwave irradiation is that microwave irradiation achieves both internal and uniform heating [5-7]. In addition, it is more convenient to control the microwave irradiation processing, because of no direct contact between the heating source and heated materials with less equipment size and waste [2, 8-9]. Life cycle assessment is used and accepted methods for the evaluation of the environmental impacts of products or systems [10]. Recently, many appropriate evaluation methods have been developed for life cycle assessment [11-12]. These proposed methods usually are employed for the evaluating product and analyzing results [13]. Among them, the analytic hierarchy process and the fuzzy comprehensive evaluation stand out as a popular method utilized in many fields [14-16]. Analytic hierarchy process and fuzzy comprehensive evaluation are a combination of mathematical and statistical technique that is useful for analyzing the effects of several independent assessment aspects on the system goal without the need of the predetermined relationship between the objective function and the assessment aspects [17-19]."

Jan 1, 2013

By B. K. Chakrabarti

Modeling and a screening design of experiment (DOE) was performed with the process variables to identify the greatest effect of variables on the response quality in the dead burning of magnesite refractory in a rotary kiln. Among various interdependent variable factors, the design variables chosen were raw magnesite (RM) feed rate, kiln rotation time i,e, seconds per rotation(SPM) and burning zone temperature (BZT). The response variables chosen were exit gas temperature and density of dead burnt magnesite(DBM). ANOVA and normal plots were used to evaluate the effects.This work had enabled to correlate the BZT, RPM, RM feed with the exit gas temp and density of magnesite produced. The result opens up an avenue to look into the optimum region of operations within the ranges of variables considered in order to conserve energy and to minimize the exhaust gas temperature and to maximize the density of the DBM produced

Jan 1, 2015

By K. Morsi, S. K. Kassegne, A. El-Desouky, K. S. Moon

"Current Activated Tip-based Sintering (CATS) is a new process for the powder-based fabrication of macro, micro and possibly nano-scale features and shapes. This new and unique process enables selective sintering of powders by localizing electrically activated sintering conditions through a stationary or moving electrically conducting tip. We present preliminary experimental results on the effect of tip size in the CA TS process as well as the effect of initial powder particle size on the sintering behavior of nickel powder.IntroductionSpark Plasma Sintering (SPS) has been the center of attention of numerous researchers due its noticeable advantages over conventional sintering techniques such as rapid heating rates, lower sintering temperature and shorter holding times. Research on SPS has been applied on a wide variety of materials such as pure metals [ 1], ceramics [2], composites [3], nano-materials [ 4], biomaterials [ 5], shape memory alloys [ 6] and many other material systems. However, it has been mostly limited to bulk materials with simple shapes with a few exceptions ofresearch efforts where the effect of electric current was combined with metal forming processes such as spark plasma extrusion [7,8] and electric rolling of powders[9]. In this paper a novel process (Current-Activated Tip-Based Sintering (CATS)) is discussed where electric current and pressure are applied simultaneously through a small conducting tip (stationary or moving) over a conducting powder compact. This process has the potential advantages of sintering complex geometries with minimum energy requirements as unconventionally high current densities can be achieved due to the small contact area between the tip and the powder compact. Furthermore, by controlling the tip size, it can be possible to sinter features on the macro-, micro- and even nanoscales."

Jan 1, 2011

By Versiane A. Leão

The adsorption of oleic acid and amine, by Expanded Hydrophobized Vermiculite (EHV) was studied. In appropriate conditions EHV is a good adsorbent for these flotation re-agents and the best results are obtained at situations where the chemicals are at non-dissociated form. The adsorbent shows good chemical stability and may been used in many adsorption-desorption cycles.

Jan 1, 1996