Search Documents

By A. A. EI-Geassy

High-grade iron ore fines rejected from the DRI plants (>96%Fe2O3) were isothermally reduced in 30-60%CO/H2 gas mixtures at 973-1273K. The freshly reduced reaction products were then subsequently carburised in either Hz/CO or H2/CO/S mixtures at 823-1 073K for 30-120 min. The thermogarvimetric technique was used to follow up both of reduction and carburisation reactions as a function of time. The carburised samples were characterized by X-ray and Mossbauer techniques. Chemical and carbon analyses were also applied. The influence of temperature and gas composition on the reduction behavior was investigated. The calculated values of apparent activation energy, application of gas-solid mathematical formulations were correlated with the microstructures to predict the reduetion mechanism. The influenee of carburization time, temperature, CO contents in H2/CO or H2/CO/S were investigated. A conversion extent of Fe to Fe3C was taken as a measurable index for the efficiency of carburization rcaction under the different experimental conditions.

Jan 1, 2003

By M. I. Kalashnikova

Gipronickel Institute has developed the technology of treatment of difficult to concentrate sulphide Pb-Zn concentrates (Zn-19,9%, Pb-8,4%, Cu-0,34%, Fe-8,8%, Ba-6,8%, S-18,7%, Ag-106 g/tonne). The technology consists of pressure leaching, impurity removal from leaching solution, electrowinning and Pb-Ag containing cake treatment. Despite low zinc content in initial concen-trate the technology allows production of solution which is suitable, after standard procedure of impurity removal, for electrowinning with production of zinc grade SHG. Comparing to the standard technologies the flowsheet developed provides the lesser expenses per zinc unit because of decreasing of liquid to solid ratio at pressure leaching stage. The initial concentrate is characterized along with low content of principal metals by high con-tent of barite, which makes flotation of pressure leaching residue more difficult. That is why in this case the hydrometallurgical treatment was chosen. At optimal parameters of chloride leach-ing found during laboratory experiments the principal components extraction was 99.5% for Pb and up to 92% for Ag.

Jan 1, 2006

By Hartmut Rossel

VAW aluminium AG has built a "Recycling-Technikum" (Recycling Research Centre) to add a new arm to the company's Corporate Research and Development Department. The Recycling Research Centre, a pilot plant for scientific research, has been in operation since September 1993. These state-of-the-art facilities allow the investigation and optimisation of recycling techniques in 'a global way and in detail. Research is concentrated on the unit operations - processing, melting and waste-gas purification - with the available installations making it possible to compare different alternative process combinations on a 100-kg scale. One of the main targets of VAW research is the development of recycling techniques for packaging. The paper presents an approach to recover the aluminium contained in flexible packaging materials using an integrated melting and waste-gas purification system.

Jan 1, 1995

MODELLING FOR DESIGN AND CONTROL AT KALGOORLIE NICKEL SMELTER Modelling at KNS has been driven by a need to have better tools to answer questions about control, design and optimisation of the plant. This paper describes a number of modelling tools developed for use at KNS and how the development of modelling tools fits with a design and control strategy. In the area of control, a thermodynamic model has been developed to allow process parameters to be calculated. The model allows for the automatic selection of data from a laboratory data base, desired operating set points are input and the operating parameters are calculated. The model has the ability to adjust the burner efficiency and the furnace heat loss depending upon conditions. To assist with the testing of proposed furnace design changes, various mathematical models of the burner and shaft have been created using PHOENICS. These models are particularly well suited to combustion heat transfer and flow aspects of both the burners and shaft. Validation of these models have been based on novel sampling and measuring techniques in the shaft and also by using scale and cold models. Overall plant energy and cost structures can be analysed using a flowsheet simulation, developed to evaluate potential alterations to the plant flowsheet. This model system allows the global evaluation of process changes.

Jan 1, 1993

By Martin Fischer

A new method for the quantitative image analysis of complex microstructures in steel is presented. Microstructures in modern steel grades on the one hand become more and more complex while on the other hand the size of the constituents is scaled down ever further. For these reasons it is increasingly difficult or even impossible to access reliable quantitative information on ratios, shapes and spatial distributions of individual phases and constituents by utilising traditional metallographic analysis methods. The presented new analysis approach is object-based. Its basic processing units are so-called ?image objects? which reflect the pictured structures by merged groups of likely related pixels. By the use of image objects, information on shape, graphical texture and spatial distribution of the microstructural constituents can be processed. With these additional data available, it is possible to quantitatively analyse complex microstructures. This is demonstrated by the application of the method to SEM images of different multiphase steel grades. Because the analysis routine is fully automated, the analysis of large amounts of image data is possible and thereby the investigation of statistically relevant areas of microstructures.

Jan 1, 2009

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By Taufiq Hidayat

Accurate description of complex phase equilibria provide the foundations for the improvement of non-ferrous pyrometallurgical smelting and recycling processes. Recent advances in microanalysis and experimental techniques enable accurate phase equilibria characterisation. Quantitative microanalytical techniques including Electron Probe X-ray Microanalysis and Laser Ablation ICP-MS enable the concentrations of major and minor elements present in different phases in samples to be accurately measured providing data that cannot be obtained using bulk chemical analysis techniques. High-temperature equilibration experiments coupled with the subsequent analysis of elementary reactions at micro- and macro-scales ensure the attainment of equilibrium conditions, and therefore, ensure true phase equilibria information is obtained. Examples of the application of the improved methodology on the investigation of phase equilibria of low-order and complex, multi-component gas/slag/matte/metal/solids Cu2O–PbO–ZnO–Al2O3–CaO–MgO– FeO–Fe2O3–SiO2–S systems and the distribution of minor element are provided. The experimental study is closely integrated with thermodynamic database development for the above system. Example of implementation of the research outcomes into industrial operations is demonstrated.

By J. Y. Foley

Platinum-group elements (PGE) are preferentially associated with chromian spinels, including high-iron chromite, magnesian-chromian hercynite, and chromian magnetite in clinopyroxene-rich upper stratigraphic portions of the Tonsina ultramafic complex in southern Alaska. Ratios of Pt:Pt+Pd are proportional to chromium content in the associated chromian spinels. The maximum PGE content of geochemical rock samples from Dust Mountain is greater than 20.000 ppb (>0.6 oz/ton) with minor gold values. The maximum PGE content of tabled chromite concentrates is 3.430 ppb (0.1 oz/ton) at Dust Mountain. 1.029 ppb (0.03 oz/ton) at Sheep Hill, and 1,749 ppb (0.051 oz/ton) at Bernard Mountain. High-iron chromite at Dust Mountain yields tabled chromite concentrates with Cr:Fe ratios between 0.5 and 1.2. Lower PGE contents are found in more chromium-rich chromitites from Sheep Hill and Bernard Mountain that yield concentrates with Cr:Fe ratios between 1.0 and 2.8. Platinum-group minerals include amalgams. arsenides. PGE alloys, and sulfides. These minerals are between 3 and 40 microns in size and are concentrated along grain boundaries and fractures of metasomatically and hydrothermally altered chromian spinel grains.

Jan 1, 1987

By Marcelo B. Mourao

Interactions of carbonaceous materials with liquid Fe-C melts have been investigated experimentally by determining the volatile yield due to rapid devolatilization (Flash Pyrolysis) and rates of dissolution at temperatures ranging from 1623 to 1873 K. The volatile yield increased with increasing the temperature. The comparison of results of different types of carbonaceous materials was possible by expressing the volatile yield in terms of Enhancement Factor, fE. The rates of dissolution of spectroscopic graphite and an industrial coke seemed to obey the correlation for natural convection under turbulent conditions. The experimental data for the graphite suggested that the rate of dissolution was controlled by the mass-transfer in the liquid boundary layer adjacent to the solid sample. The value for the empirical parameter correlating the dissolution coefficient and the operating variables was found to be 0.19 which was close to that reported in the literature. The comparison of the results obtained for the coke samples with those for the graphite revealed that the impurities and the porosity of the samples can effect the dissolution rates.

Jan 1, 1992

By D. B. Dreisinger, V. van der Pas

Zinc sulphate electrolyte used for zinc electrowinning must be purified for cObalt ions. The cobalt is removed in a cementation stage by the addition of zinc dust. Copper arid antimony are frequently used additives which enhance the cementation of cobalt. This paper aims at a better understanding of how copper and antimony promote the removal of cobalt. Initial experiments were done in a batch cementation reactor. Copper and antimony precipitated in the early stages of cementation indicating that a preferential substrate was formed. The individual role of copper and antimony was further investigated in an electrochemical cell. On a microsca1e, the , growth process, morphology and the composition of the precipitates were examined with SEM and XRD. It was found that cobalt could not be deposited in its pure form but as a cobalt-zinc alloy with zinc as the prime constituent. Copper increases the cathodic surface area of zinc dust by precipitating as numerous dendrites. Antimony acts as a cathodic surface onto which a cobalt-zinc alloy with an increased cobalt content is deposited.

Jan 1, 1997

By Shaohua Ju, Feng Jiang, Chuanhua Li, Jinhui Peng, Libo Zhang

A T-junction microchannel is proposed to overcome the existing problems in conventional solvent extraction of indium from zinc hydrometallurgical process. Experiments were performed to separate In3+, Fe3+ and Zn2+ from sulfate solutions using Di-(2-ethylhexyl)phosphoric acid (D2EHPA) as the extractant. The effect of parameters such as pH, microchannel size and contact time on the extraction behavior of In3+, Fe3+ and Zn2+ was investigated. At contact time of 2.52 s and initial solution pH of 0.48, the extraction efficiency of In3+, Fe3+ and Zn2+ was 99.13%, 8.31% and 2.45%, respectively and separation factor of In3+/Fe3+ and In3+/Zn2+ were almost 1229.54 and 4864.98, respectively. Then, the loaded organic phase was stripped in T-junction microchannel. At contact time of 33.6 s, 99.64% of stripping efficiency of In3+ and stripping equilibrium were reached, while concentration of Fe3+ and Zn2+ was lower than 0.01 g/L with good separation of In3+ from Fe3+ and Zn2+.

Jan 1, 2016

By Frank Mucciardi, Hujun Zhao, Pietro Navarra

"A heat pipe is a device having a very high effective thermal conductivity in which two-phase flow and heat transfer takes place. Recent research at McGill University has led to a new type of heat pipe that contains a flow modifier. This improvement has enabled the device to operate at the high heat fluxes encountered in the metallurgical industry.This paper summarizes the progress made to describe the fluid flow in the evaporator section of a McGill heat pipe with the goal of understanding how the flow modifier configuration is linked to the film boiling and dry-out limitations. A separated flow model, an instability analysis, a lift-off model and an energy balance model are used to calculate the theoretical CHF with varying flow modifier configurations and operation conditions. A summary of the current work to relate the flow modifier to the dry-out limitation is also given.Determining how the flow modifier affects both the film boiling and dry-out limitation will give insight into improving the flow modifier design so as to extend the operational range of McGill heat pipes in terms of maximum heat flux and heat load capabilities.IntroductionThe McGill heat pipe is a specialized two-phase heat exchanger developed for several metallurgical applications where temperatures and heat fluxes are typically close to or beyond the maximum safe range of conventional cooling technology.Over the last few years, several breakthroughs have brought this device beyond the proof-of concept stage and a series of industrial trials have been performed with success. These trials include two oxygen injection applications for the ferrous and non-ferrous industry [l], and two light metals permanent-mould casting applications [2,3]. Current projects include a blast furnace copper taphole cooling application [4], a copper smelting application and a thermal analysis probe application."

Jan 1, 2004

By Edita Vircikova

The best demonstrated available technology (BOAT) for the removal of dissolved arsenic and some heavy metals as reported by USEPA (Contaminants and Remedial Options at Metal Sites, Draft Report, August 1993) (1) is still the chemical precipitation. Coprecipitation with the excess of iron is usually practised because of the availability of iron at low/no cost and also in order to meet the stringent regulatory discharge limits. The arsenic is usually removed with iron because of its common occurence in the mined orebodies and the excellent adsorptive property of the precipitated hydrous ferric oxide compounds. There has been controversy, however, over the long-term stability of the arsenic-bearing ferrihydrite which is produced.

Jan 1, 1995

By Andrey Tarasov, Erki Unn, Valery Paretsky

"The stability of the markets of energy resources and labor in countries of the Baltic Sea Region including Estonia is determined to a significant degree by the use of combustible shales as fuel and their distillation resulting in generation of up to 70% of non-recyclable waste. The objective of this business plan is to substantiate the investments for establishment of a new facility in Estonia for waste-less and environmentally safe processing of fossil minerals and man-made products generated in the shale industry, as well as other hazardous wastes. The proposed facility will use a basically new waste processing technology developed in Russia - i.e., processing in sparged molten slag This technology eliminates any release of harmful pollutants to the environment and a facility using this technology does not require, therefore, any sanitary protection zone.IntroductionIn the Baltic region, and first of all in Estonia and some other European territories, there are large natural deposits of combustible shale, which due to the lack of other own resources of energy and hydrocarbons for the chemical industry is burned and distilled with low technical and economic efficiency generating large amounts of toxic and highly toxic wastes and intermediate products. Currently, the penalties for disposal of such wastes have grown to such an extent that shale burning and distillation might become unprofitable. This might result in suspension of the given operations, which in turn will affect in an adverse way the markets of energy resources and labor market in those countries. Furthermore, in addition to the “shale problem”, Estonia, similarly to most member countries of the European Union, faces the challange of environmentally safe processing of highly toxic wastes, such as municipal solid wastes, oilpolluted materials, medical wastes and infected materials, spent rubber tires, etc. These wastes are at present stored or processed with release of a significant quantities of extremely toxic cancerogenic substances (dioxins, furans) or collected and exported for treatment at an extremely high cost and with a loss of valuable components contained in these types of waste and often with return of supper toxic processing products."

Jan 1, 2008

Conventional ferronickel smelting has five main steps: Drying, calcination, prereduction, smelting and refining. In the scope of the current work, smelting experiments were conducted using Sivrihisar laterite ores (1.26% Ni) of Turkey. The ore samples previously subjected to drying, calcination and prereduction stages were smelted in alumina crucibles in a laboratoryscale horizontal tube furnace under argon atmosphere. Smelting experiments were performed at 1500, 1550 and 1600 oC. The amount of excess coal used in prereduction step was another variable. Sivrihisar laterite ore is a limonitic one with low MgO composition. Therefore, MgO was added to the smelting charge as a flux. The effects of experimental variables on metal Ni content and slag composition were investigated.

Jan 1, 2012

By Mark Osborne, Ray D. Peterson, C. Edward Eckert

"The theoretical melting energy requirement for a typical hypoeutectic aluminum-silicon alloy is approximately 520 BTU/lb. It has been demonstrated, however, that even a state of the art secondary processing-automated lost foam casting operation can exceed this value by at least an order of magnitude when the actual thermal energy input from melting to solidification is monitored. Metal transfer and holding operations constitutes over 65% of this expenditure. The authors present relative benchmark energy expenditure information by unit operation for an offsite melting/lost foam casting line with a daily throughput in excess of 100,000 lbs. Efficiency improvements through optimization of the current process, and anticipated energy values at the culmination of a U.S. Department of Energy sponsored project to develop, integrate and demonstrate an advanced melting, transportation, and dispensation system will be cited.IntroductionThe size of the U.S. aluminum remelt pool was approximated to be 14.21 billion kg (31.27 billion pounds) by a recent study?, with the engineered castings (foundry) sector accounting for 3.25 billion kg (7.16 billion pounds) or 23% of that total. This study considered overall process yield and all major contributors to scrap. The values cited, therefore, are more meaningful than simply tabulating annual pounds shipped by sector.The foundry sector consists of Sand Castings, PM Castings and Die Castings categories appearing in Figure 1. All other categories comprise the wrought alloy sector. Wrought alloy production enjoys an energetic benefit from both scale and a relatively continuous operation. Many foundry operations, however, operate in batch mode at less than design metal throughput with characteristically longer melt holding periods. Since any detention of molten metal beyond melting represents an overhead use of energy, melt holding (secondary) energy expenditures can appreciably inflate melting energy requirements in the foundry."

Jan 1, 2009

By Bo Björkman

Four different arsenic containing dusts from the Boliden plant, Boliden mineral AB, Sweden have been examined. A kinetic study of the As elimination was performed in a laboratory scale roasting furnace for roasting furnace ESP dust and smelting furnace ESP dust. Characterisation and thermodynamic calculations were carried out to determine the mineralogy, and the stability of compounds in the dusts studied. The characterisation methods used were chemical analysis, X-ray diffraction analysis and microprobe analysis. It was found in the experiments that a high degree of As elimination was obtained for roasting fumace ESP dust and a low degree for smelting fumace ESP dust. Derived kinetic models are given. A prediction of the As-elimation for settling furnace dust and converter ventilation dust is presented.

Jan 1, 1994

By Hazoor Singh Sidhu

Materials degradation due to corrosion is the major problem in power generation equipment, gas turbine, fluidized bed combustion, industrial waste incinerators etc. Some super alloys have been developed, but they are unable to have different properties to meet the demand of today?s industry. Therefore, a composite system of a base material providing the necessary mechanical strength with a protective surface layer different in structure and/or chemical composition can be an optimum choice in combining material properties. Thermal spray coating of the components before they put into service by suitable surfacing alloy and with suitable coating method can increase the life of these components several fold. Choice of right coating method and alloy for a particular application is extremely important to get the desired service life. The corrosion of some materials and the role of HVOF thermal spray coatings to counteract the same have been reviewed, with an aim to understand the phenomena along with various applications.

Jan 1, 2006

By Massoud Hassanabadi

Filtration using Ceramic Foam Filters (CFFs) is a method widely used to separate inclusions from molten aluminium. In the present work, the specific permeability and form drag coefficients of nominal 50 mm thick commercial Al2O3- based CFFs, of grades 30, 50, 65 and 80, have been calculated from pressure drop experiments using high (60–500 mm s−1) and low (0.2–10 mm s−1) water velocities. Moreover, 2D axial symmetric Computational Fluid Dynamic (CFD) models have been developed, using COMSOL Multiphysics® to validate the experimental results. The empirically obtained values were defined as global parameters used to model the pressure, as well as the velocity fields in the water pipes and in the CFFs. The modelled pressure drop over the filter thickness for the high water velocity experiments showed < ± 1% deviation from the corresponding experimental results for all CFF grades. Moreover, the developed model also showed good agreement with the experimental results obtained from the low water velocity experiments, where the deviation of the pressure drop for the CFF samples of grade 30, 50 and 65 were ≤ ± 4.6% and for CFF samples of grade 80 ≤ ± 13.4%.

By Robert E. (Bob) Brown

Magnesium was discovered by Davy in 1808. The production processes as they exist are not economically competitive with aluminum The electrolytic magnesium process is divided into two steps; one to make the MgCh feed and the other to apply large amounts of electric current to dissociate the feed into magnesium (450 g) and chlorine (1200 g). The production of fuJIy anhydrous, pure cell feed is a major problem Recently, there has been a growth of thermal processes, mainly the Pidgeon silicothermic production process using FeSi to reduce dolomite in horizontal retorts. Pechiney has a large vertical electrical furnace process that also uses FeSi to reduce calcined dolomite in a molten bath containing alumina. Work is proceeding to develop new or modified processes that will greatly improve magnesium production. The present methods and the research and R&D will be reviewed in this paper.

Jan 1, 2001