Search Documents

By S. M. Hsiung

In late September 1984, a longwall panel in West Virginia lost 60 powered supports when the face had advanced for 250 ft. from the setup entry. An in-mine investigation showed that it was a first weighting failure resulting from inadequate Support capacity. This paper presents the results of finite element modeling, which have led to a better understanding of the first weighting failure mechanism. The dynamic impact of the first weighting failure on the powered supports is analyzed. The optimum capacity for the powered supports in order to control the roof at face area under the geological condition is discussed.

Jan 1, 1984

By John L. Hill

Cutter roof failure is a specific type of ground control problem which frequently results in massive roof failure. It is a cannon occurrence in coal mines of the Northern Appalachian Coal Sasin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure togain a basis from which to prevent its occurrence and to support such roof when failure does occur. Research conducted in a coal mine of central Pennsylvania has revealed a correlation between the occurrence of clastic dikes and fonation of cutter roof failure. Inmine mapping of ground conditions showed an increase in roof failure in areas of high frequencies of clastic dikes. Rock pressure monitoring around clastic dires registered the greatest amount of roof loading near the inter- section of dikes with the rib. Load cells measurim horizontal pressure changes in the roof indicated that the greitest pressure changes were occurring perpendicular to entry headings when clastic dikes were present. Analysts of rock pressure nwnitiring shows that the roof behaved as two cantilever beams when severed by a clastic dike. Additional roof supports such as trusses and cribbing were found to effectfvelv suooort the roof in areas of clastic dikes and prevent cutter roof iailure. However, there lnethads were only successful when employed shortly after mining.

Jan 1, 1984

By K. Hanna

This manuscript describes an extensive ground control study at the Inland Steel No. 2 Mine near McLeansboro, IL, conducted by the U.S. Department of the Interior's Bureau of Mines (USEM) in cooperation with Inland Steel Coal Co. The mine experiences severe ground control problem primarily due to high horizontal stress, particularly at entry intersections. Mine experience has shown that reorienting mine entries, modifying the bolting pattern, and altering the mining sequence are effective in reducing the severity of roof falls and out-of-seam dilution. However, the frequency of roof falls has not been significantly reduced. This research project was designed to provide a thorough explanation of the intersection failure mechanism through combined analyses of company in-mine experience and Bureau field measurements. Stresses and deformations were monitored in a four-way intersection during all stages of development and were related to site observations and theoretical analyses. The results of the combined analyses indicate that high horizontal stress is the predominant factor contributing to intersection roof falls in the Inland Steel No. 2 Mine. The horizontal stress induces shear zones to form along the outby 1 ribs, causing the immediate roof layer to detach 1 and behave as a cantilever beam oriented diagonally across the intersection and parallel to i the maximum horizontal principal stress. As the shear zone progresses upward, roof layers successively detach and fail, forming a dome-type roof fall.

Jan 1, 1986

By Y. P. Chugh

About 60-70% of the underground mined coal in Illinois is extracted using a room-and-pillar mining method that permits extraction of about 50% of the coal. The remaining coal is left behind in the form of support pillars to control surface and subsurface movements. Illinois coal seams are typically associated with water sensitive weak floor strata whose thickness varies 0.31 - 1.3 m. The current mining geometry mostly uses pillars of constant size within a mining area. This traditional practice suffers from the disadvantage that pillars within the center region are subject to much higher loads than the pillars located on the outer edges of the panel. This results in a higher incidence of rib spalling, and roof falls, creating a potentially hazardous work environment. In addition, this concentration of loading at the center of the panel provides initiation points for floor failure to occur. The primary goal of this study was to reduce ground control problems and production costs in Illinois mines by considering alternate mining geometries. The development and subsequent field demonstration of an alternate geometry is presented in this paper.

Jan 1, 2004

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003

By E. M. Williams

The U.S. Bureau of Mines is investigating the use of in-seam seismic methods to monitor stress-induced changes in coal near the working face of longwall mines. Seismic surveys performed through a longwall panel and pillars near the face can provide valuable information on geologic anomalies, high stress regions, tailgate support performance and other conditions that could endanger miners or interrupt production. This paper describes the details of the equipment and data analysis techniques used, and the significant results obtained and their implications for ground control. Using seismic tomography, it is possible to conduct measurements on the pillar and reconstruct an image representing the internal velocity distribution. Successive measurements over several days identify changes in velocity attributable to changes in stress. Several field measurements were conducted at a western U.S. longwall mine to observe stress induced changes within the panel and pillars during mining. A permissible data acquisition system was designed to meet mine safety requirements for operation in gassy air. Certification from the Mine Safety and Health Administration (MSHA) was obtained, and this approved system was used to monitor stress changes in several pillars as the longwall face passed during first panel mining. Tomographic surveys were completed across the longwall panel to map the apparent abutment stresses ahead of mining. Velocity distributions show an increase in vertical stress across the panel from the headgate to the tailgate. Additionally. a yield zone along the face near the tailgate and the forward abutment approximately 100 feet outby the face in the tailgate side of the panel were detected. These results agree well with data obtained from other instrumentation emplaced in the panel near the tailgate. Using velocities for both compressional and shear waves, the Poisson's ratio was calculated for the panel.

Jan 1, 1994

By Kevin Beauchamp

In many cases traditional support designs cover the many variations in ground conditions and bolt performance by a conservative factor of safety. The result is that most bolts are ineffectual most of the time and yet the response to occasional roof collapses is an even more conservative design. The probabilistic analysis presented in this paper takes several important parameters of a support design into account such as span, bolt strength, bolt length, water pressure, seismic accelerations, joint orientation, bed thickness and joint strength and allows the effect of variations in these parameters to be evaluated simultaneously. The analysis demonstrates the application of the probabilistic approach to both blocky, wedge-dominated conditions and bedded deposits dominated by laminations. All mine excavations have a designed stand-up time. By taking into account of the possible variations in the design parameters explicitly, it is possible to produce a support system designed to ensure stability over a given period of time. Rather than use a factor of safety criterion, the approach uses a percentage reliability or probability of failure. By understanding the probability of failure of the support system, it is possible to improve the performance of ground support without any increase in cost or conversely to decrease the cost while maintaining the performance of ground support. This approach reduces reliance on empirical experience and leads to a better understanding of the key factors that influence stability and can provide a much more accurate and optimized assessment of support design and performance. The result is a more cost-effective support system and we hope that a broader application of this approach to ground support in underground mines will lead to a greater acceptance in the industry of probabilistic analyses and of terms such as Probability of Failure and Reliability of Support.

Jan 1, 2003

By Ismet Canbulat

The cut out distance in the continuous miner sections in South African collieries is limited to 12 m. However, this distance can be extended to 24 m by the permission of the Department of Mineral and Energy (DME). This paper investigates the risk of roof Calls associated with the extended cut out distances permitted by the DME. Extensive underground experiments have been conducted using sonic probe extensometer under various geological conditions to identify the effect of cutting distance and tinge on the stability of the workings and the performance of the support. The results showed that that the most critical parameter with respect to ground control aspects of extended cut out distance is the bord width, which determines the amount of deformation that will take place in the roof. This was confirmed by the numerical modelling. The results also showed that a significant portion of the maximum deformation in the roof takes place before the ratio of cut out distance to bord width exceeds two. This indicates that once the face is extended more than twice the bord width, the roof will stabilise, assuming that no geological discontinuity is present and that there will be no further geometrical changes in the area as a result of for example the development of an intersection.

Jan 1, 2000

By Anthony Iannacchione

As the amount of new fractured surfaces or "damaged rock layers" within roof rock increases, the stability of the rock mass decreases. While direct measurements of this phenomenon are not easily made, there is good circumstantial evidence to support this hypothesis. For example, it is common to observe increased cracks or fractures in the immediate mine roof rock before a roof fall. Likewise, roof drill holes placed in areas that later fail often reveal increased numbers and/or separations of fractures within the rock column through time. And finally, the frequency of microseismic activity, representative of rock fracturing, increases before a roof fall. For this study, more than 700 microseismic emissions were collected from two underground limestone mine roof fall areas in southwestern Pennsylvania. Microseismic events were located and magnitudes determined using the moment magnitude technique. Moment magnitude is based on the event seismic moment, which is a measure of the seismic deformation. The amount of new fracture surface length was calculated based on the stored strain energy within the rock prior to fracture. In the two case studies presented, a significant amount of microseismic activity was observed as much as two days before the first signs of failure in the roof fall areas. Additionally, results from this analysis reveal much about the behavior of strata prone to failure and allows for the construction of hazard maps based on microseismic emissions. The potential use of this technique as a means of anticipating roof falls is analyzed and discussed.

Jan 1, 2004

By Ross W. Seedsman

The in situ behaviour of claystone floors associated with the Wallarah, Great Northern and Fassifem Seams has been studied using a comprehensive suite of stress and displacement monitors. The instrumentation was supplemented by in situ and laboratory testing of the claystone materials. The instrumentation demonstrated that the presence of claystone floors is associated with floor heave, extra rib spall, and settlement of the pillar into the floor. Horizontal floor extensometers showed that the depth of extrusion of clay was limited to 1-2 in. A pore pressure transducer installed in a claystone floor demonstrated the possible existence of short-term undrained behaviour of the claystone. Long term swelling of destressed claystone was also documented. Settlement of pillars into claystone floors can be analysed using simple elastic theory. The assumption of plane strain is valid for most claystone thickness/pillar width aspect ratios. Floor heave can be analysed using bearing capacity concepts. However, it is considered that heave is the result of local bearing capacity failure in the rib spall zone. The advantage of this model is that the bearing capacity equation can be applied without resort to unrealistically high factors of safety.

Jan 1, 1992

By J. S. Oram

Maltby Colliery, operated by RJB Mining (UK) Ltd is successfully mining the Parkgate seam in Yorkshire at a depth of 1000m using longwall retreat. Extraction in the Parkgate seam is influenced by interaction from previous workings in the Swallow Wood Seam 160m above. The paper describes in-situ stress measurements and simple gate road convergence measurements carried out to assess the extent of the interactive influence. The stress measurements, obtained using the stress relief overcore technique, were carried out from a maingate development roadway in an area where the stress redistribution under an overlying pillar and adjacent panel goat could be measured. The measured vertical stress distribution confirmed a significant interactive influence with high imposed vertical stresses under the overlying panel edges. Simple roadway convergence monitoring stations established in the gateroads of a retreating panel and in the development gateroads of the adjacent panel, confirmed higher rates of roadway deformation relating to overlying panel edges and pillars, particularly in the areas where a vertical stress window developed during panel retreat. In addition to highlighting a close relationship between closure rate and the measured vertical stresses, the convergence monitoring proved valuable in establishing characteristic deformation behaviour under specific interactive influences and also in defining the optimum location, extent and time of installation u£ additional roadway support and reinforcement. The information from the measurement programme has enabled the Mine Management to gain a better understanding of the interactive influences on roadway behaviour and was instrumental in designing the layout of panels in an area of the North East district of the mine where previous experience had indicated the combined influence of high interactive stresses and weak roof lithology resulted in difficult strata conditions both at development and on panel retreat. The planned location of panels and gateroads took into account both mining operational considerations and the need to avoid potentially high risk interaction zones as highlighted from analysis of the monitoring results. To obtain additional data on parameters influencing roadway deformation, extended roadway convergence monitoring has been established.

Jan 1, 1997

By Christopher Mark

Coal bursts are typically associated with highly stressed coal. Most bursts occur during retreat mining (longwall mining or pillar recovery) in highly stressed locations like the tailgate corner of the longwall panel. Others are associated with multiple seam interactions. However, a small but significant percentage of coal bursts have occurred during development or in outby locations unaffected by active mining. Most development bursts have been relatively small, but some have been highly destructive. No theory of coal bursts can be complete if it does not account for this type of event. This paper focusses on the development mining coal burst experience in the US, putting it into the context of the entire US coal burst database. The first documented development coal burst occurred almost exactly 100 years ago during slope drivage at the Sunnyside Mine in Utah. Sunnyside subsequently had a long history of bursts, mainly during retreat mining but also during development. Several Colorado mines have also experienced multiple development bursts. Some, but by no means all, of the development bursts in these western US coalfields have been associated with faults. In the Central Appalachian coalfields, most development bursts have occurred in multiple seam situations. In some of these cases, however, there was no retreat mining in either seam. The paper closes with some lessons from this history, with implications for preventing such events in the future.

Jan 1, 2017

By Duk-Won Park

A vast majority of the operating longwall sections use shield-type face supports to provide ground control in the United States. As a co-operative research program between the University of Alabama (UA) and Jim Walter Resources, Inc.(JWR), a joint research program is underway to study interaction of shields with surrounding rock masses. A series of analyses on the response of shields are performed using monitored data at a longwall face in a deep coal mine. In this paper, various effects of parameters, such as leg pressure, setting load, developing load, maximum loading rate, pressure in capsule, and convergence between canopy and base, are discussed and recommended as stability indices. A microcomputer program is being developed for instantaneous interpretation of the shield monitored data, and for giving warnings of potential problems. The preliminary results define the effects of the setting load, developing load, and rate of developing load or leg closure rate. The objective of the study is to understand the shield characteristics and their interaction with surrounding strata in real time, then develop a reliable program for maintaining longwall stability.

Jan 1, 1992

The formation of tension cracks in slopes is well known. Analytical studies require the determination of a critical slip surface for any slope and, in doing so, it is necessary to consider an appropriate tension crack. A general yet simple approach is proposed for identifying the critical slope failure surfaces associated with critical tension cracks. The minimum factor of safety consequently reflects both safety against shear sliding and tensile failure. In general, the critical slope failure surface for a slope determined in this way differs from that which is obtained without optimizing the position and depth of the tension crack. In particular situations, the difference is significant.

Jan 1, 1989

By I. Geldmacher

In-Seam Seismic (ISS) methods have been used extensively worldwide for the past 10 years to assist mine planning, espe¬cially longwall mining in coal seams. The technique is only starting to gain wide acceptance in North America where it is being applied in a much wider variety of applications than was initially considered. Surveys elsewhere have concentrated on the detection of faults (structures) in coal mines prior to longwall mining. The majority of surveys in North America has been the location of abandoned workings which were not adequately surveyed prior to closure. Modeling data based upon the lithological logs, geophysical logs and interpreted sections show whether the method will be successful prior to carrying out the survey. The surveys have been performed to locate abandoned wor¬kings from the surface and underground using both seismic reflection and transmission techniques. Data from coal seams in both Illinois and West Virginia will be presented. A second method where ISS surveys are being applied to detect old workings will be presented. The ISS tomography produces an image of the P-wave and Channel Wave velocities which is representative of the material through which the signal traveled thus identifying the location of the old workings. Data from Texas will serve as an example.

Jan 1, 1990

By David I. Hoyer

It is shown that by monitoring longwall leg pressures in real time, warning can be given for significant weighting events and the formation of roof instabilities, such as roof cavities, several hours in advance. Longwall Visual Analysis (LVA) is a software package that continuously monitors shield pressures and shearer position in longwall mines. LVA has been running on 19 Australian longwalls for up to four years, and as a result a very substantial database of shield pressure trends in a wide range of longwall situations has been collected. This database has been analyzed to develop indicators that will give operators and geotechnical engineers advance warnings of developing conditions such as weighting events and difficult roof conditions. LVA displays live charts of data, such as shield leg pressures, loading rates, and yield frequencies. Data analysis techniques were applied to historical data records from multiple longwall sites in order to develop a ?Cavity Risk Index? (CRI). The CRI indicates the risk of roof cavities developing, and it is based on pressure trends that indicate significant yielding and loading rates spanning a region of relatively low support. Case studies from different longwalls are given, showing how the CRI can give real-time advance warning of the formation of roof cavities with their anticipated location on the face. The limited number of case studies done so far indicate that the predictions have a high degree of reliability, but more work is required to quantify this.

Jan 1, 2011

By Mietek Rataj

Installation of pre-tensioned Strand Bolts i.e. resin grouted cable bolts is very common now in Australian coal mines. A short historical development of this type of rock reinforcement is outlined Various systems have been developed to apply 20 to 25 tonnes of pre-load to these bolts but there are still some technical problems which have to be overcome. One of the major problems encountered is bleed off tension which is highly undesirable as required "over loading" rocks the immediate roof thus inducing fractures iii weak strata. The major reason for the loss of tension apart from the design of the tensioning jack, is the design of the conventionally used barrels and wedges. Due to a roof plate tilting during tensioning the cable moves out of the barrel centre which impedes proper positioning of the wedges and subsequent excessive return of the cable once load of the jack is released. This problem has been largely resolved by the design of a special barrel having a centralizing rim allowing for significant reduction of the toss of tension. KEYWORDS: Pre-tensioned Strand Bolts, Cable Bolts, Bleed off Tension, Tensioning Jack, Loss of Tension

Jan 1, 2002

By A. H. PH. D Wilson

Compared to the rocks encountered in, say, metalliferous mining or tunnel drivage in igneous and metamorphic rocks, the strata associated with the coal measures are relatively soft. If excavations are made at depths greater than one or two hundred metres, zones of fractured or yielded rock develop around the openings. The stress which can be taken by yielded rock at the boundary of an opening is low, but because of the friction present between the fragments or particles, the sustainable stress rises rapidly with distance from the opening until sufficient confinement has been developed to prevent failure of the rock in the first place. Thereafter the laws of elasticity will apply and increasing distance will reduce the stress field until conditions consistent with the cover load are reached. For rocks which maintain their elastic condition right to the edge of an opening, finite element analysis and similar techniques have proved successful in determining the distribution of stress around the opening. This approach, however, is not successful when a yield zone is introduced between the elastic zone and the opening. Nevertheless, some estimate is required if help is to be given in the siting of roadways and in the determination of adequate pillar sizes. This matter is of particular importance in the planning of new mines especially if retreat faces are involved, as extensive roadway drivage must be planned and executed before experience of the effects of face extraction is gained. In 1977, the author published [I] a method based on 'stress balance'. The total aggregate downward load over a large area will remain that of the cover load even after part of the coal seam has been removed. Any rise in stress in ribsides and pillars must be offset by an equivalent stress reduction across roadways and other areas of extraction, and vice versa. Knowledge of one can lead to an estimate of the other, provided the general form of the stress distribution can be postulated. It is the object of this paper to revue the method in more detail and to give further examples of its successful application.

Jan 1, 1981

By Yong-Ming Jiang

Longwall mining systems are extremely complex and expensive and require great caution for reliable and efficient operation. In many cases, ground control problems are the primary concern in longwall mining. For example, unexpected threats such as roof falls or shield damage can cause sudden interruption of coal production and safety problems, which can originate from many parameters such as shield capacity, setting load, shield type, conditions of immediate and main roofs, pillar stability, geological anomalies, etc. However, it is difficult to correlate ground-control problems at a longwall face with the related mining and geological factors. In this paper, a method of correlation analysis, called tree classification, which permits the use of a large and variable number of features, is introduced The method provides an effective approach to produce an accurate classifier or uncover a knowledge structure, which will be used to predict future consequences depending on past and current data sets. The application of the tree classification method in longwall stability analysis is discussed, and the major procedures of constructing a knowledge structure are included as an example utilizing monitored leg pressure data in a longwall face. Also, the importance and ranking of the variables related lo longwall shield stability is discussed This is a major step towards developing an artificial intelligence system for real-time interpretation of shield monitoring data and hazard prevention.

Jan 1, 1993

By Dave Forrester

Mining subsidence over shallow abandoned coal mine workings is unfortunately not an uncommon experience in the coalfields of North America and there is a significant knowledge and literature base addressing the phenomenon and related issues. From time to time, however, a case history arises which is outside the more routine occurrence. This paper addresses one such case and presents an overview of a subsidence Event above abandoned coal workings, which badly damaged a two-story High School building. The subsidence at the Cape Breton & Victoria Regional School Board (CBVRSB)'s MacDonald High School in Dominion, N.S., Canada on October 30, 2002 led to a detailed investigation. It was concluded that the ground movement and associated building damage had been caused by mining subsidence in underlying old underground coal mine workings of the 1890s, only 150 ft deep at the School. The Event was not isolated and a similar but smaller event happened nearby a few months later. The paper describes the events and summarizes the subsequent investigations and findings. The 17-year old High School building was eventually demolished.

Jan 1, 2004