Search Documents

By D. M. Carris

Since the Buffalo Creek incident in February, 1972, Federal and state environmental agencies have had the pressure on the coal industry in the Appalachian area to close the coal processing plant water circuits. In an attempt to comply with this requirement, Eastern .Associated Coal Corp. decided to install a vacuum disc filter system at its Kopperston plant to eliminate the tailings pond and reduce the amount of plant make-up water. It was recognized at the time that the plant static thickener tailings would be a very difficult slurry to dewater because of its unusually high clay content. The following is a case history of the Kopperston installation and the refinements Eastern has made in its vacuum disc filter operation to increase efficiency.

Jan 1, 1979

By L. E. Beverage

In 2006, the Mine Improvement and New Emergency Response Act (?2006 MINER Act?), Pub. L. No. 109-236, 120 Stat. 493 (2006) was enacted in a bi-partisan move to strengthen the 1977 Mine Safety and Health Act. This action followed several underground coal mining accidents at the Sago and Aracoma Mines in West Virginia and the Darby Mine in Kentucky. The focus of that legislation was, in part, to force technological development and implementation. It involved the recomposition and training of rescue teams. Requirements for sealing worked out areas of mines were changed when MSHA invoked its Emergency Temporary Standard (?ETS?) authority for the first time in many years. Increased penalty amounts were established for certain types of violations for all types of mining, and minimums were set for unwarrantable failure violations issued under Section 104 (d)(1) and (d)(2); 30 U.S.C. Section 814 (d)(1),(2). The entire 30 C.F.R. Part 100 penalty criteria was revamped in a rulemaking, effective in April 2007. The visions were ambitious and noteworthy and those in industry and government have spent the last four years working through the aftermath of intended and unintended consequences of these changes. The penalty structure arrived at in 2007 has proven unwieldy and has contributed to the increase in contested caseload now before the Federal Mine Safety and Health Review Commission. In essence, litigation under the Mine Act ground to a virtual halt when the number of cases increased but the budget for Administrative Law Judges, who hear the cases, and the Solicitor?s office who represents MSHA, was not increased. Addressing the backlog effectively was one of the major challenges when Joe Main was confirmed as Assistant Secretary in early 2010.

Jan 1, 2011

By R. W. Waytulonis

This paper is an update of the activities of the U.S. Bureau of Mines, other government agencies, and the automotive and truck industry concerning diesel emission control. Enacted and proposed regulations from the U.S. Mine Safety and Health Administration (MSHA) and developments in diesel emission control are presented in terms of their impact on underground coal, metal, and nonmetal mines. Mine air quality regulations proposed by MSHA may require the underground mining industry to comply with new standards. Some mines may be required to take additional actions to meet new diesel particulate and lower nitrogen dioxide exposure standards; however, the mining industry is in a position to benefit from emission controls developed for the on-highway diesel engine market. The U.S. Environmental Protection Agency (EPA) has enacted regulations to reduce emissions from on-highway diesel trucks and buses. Engine manufacturers have responded by developing cleaner burning engines. Fuel producers have responded by providing cleaner burning reformulated diesel fuel, and exhaust aftertreatment devices have been developed to provide additional emissions reductions. Bureau research and development projects seek to determine the advantages of using modern engines and fuels, and to evaluate the efficacy of new exhaust control devices on mining machines. It appears that the diesel engine will continue to be a practical power source for use in confined environments because no other available power source is as mobile and efficient.

Jan 1, 1993

By Bob Katsiouleris

Having passed through the worst of times for industrial minerals demand, there are signs that the best of times lie ahead. If the downturn was the result of unsustainable economic policy, the path forward has everything to do with sustain-ably meeting the demands of more people enjoying higher standards of living than ever before. Minerals producers must be poised to understand and meet their requirements well into the next decade. Successfully marketing industrial minerals - the building blocks of a growing and increasingly urban world population - will depend on producers? ability to respond nimbly to a rapidly changing and regionally evolving macroeconomic environment. A renewed focus on energy conservation, sustainable agriculture and building practices and consumer demand for products with a smaller environmental footprint will drive product and market segmentation strategies. These trends will not only shape the way industrial minerals producers do business, but also the type of skills and people they will require to run those businesses.

Jan 1, 2011

In order to ensure safe mining and reduce surface damage in shallow multiple-seam mining, the failure characteristics of interburden strata with different coal pillar offset distances between pillars in the upper and lower seams, the distribution characteristics of stress concentration in coal pillars, and the development characteristics of stratum cracks and subsidence were physically investigated and also using UDEC2D software. Meanwhile, the effect of different coal pillar offset distances on the stress concentration of coal pillars and development of stratum cracks were studied. Based on those results, a formula for safe mining and reducing surface damage was established, which provided a theoretical basis for safe and environmentally friendly mining in shallow multi-seams. According to the results of the study, the optimal coal pillar offset distance (the side-to-side horizontal distance of the upper and lower coal pillars) between the upper and lower coal seams was developed to reduce the stress concentration of coal pillars and surface damage. The results of this study have been applied in Ningtiaota coal mine and have achieved good results in safe and environmentally friendly mining.

Jul 28, 2020

By Steven E. Mischler, Jay F. Colinet

The study analyzes the impact of the Continuous Personal Dust Monitor (CPDM) on reducing overexposures to coal mine dust. It compares compliance sampling data before and after the implementation of the CPDM and the 2014 MSHA dust rule. The results indicate a significant reduction in the percentage of samples exceeding the dust standard for various mining occupations, highlighting the effectiveness of the CPDM in improving miners’ health and safety.

Feb 22, 2022

By H. A. Stoess

The Minerals Industry makes heavy demands for and on its Material Handling equipment. It also gives progressive management the opportunity for considerable savings, ad consequently increased profits. In some cases, cost of Materials Handling amounts to 40°/o of the total cost of the ultimate product. Handling costs are hidden in overhead, indirect labor, excessive maintenance, productive workers performing handling tasks, and, a great many more. Even though Materials Handling is the oldest occupation of mankind, it is only within the past twenty years that it has emerged as a specialized field. While this industry has made full use of all types of mechanical and vibratory conveyors, pneumatic conveyors in their proper application can be a distinct asset. me use of pneumatic conveyors by this industry however is limited- to a certain extent by the particle size of your products through the various phases of manufacture, as well as their bulk density. However, with increasing knowledge of the fluidization of dry materials, their use is becoming more wide spread.

Jan 1, 1962

By Mark J. Zdunczyk

"Frac sand is industrial silica sand much like glass, foundry, filtration and blast sand. The sand must meet certain specifications set forth by the industry that consumes the product. The production and consumption of frac sand has experienced record growth in the last 10 years because of new oil and gas drilling, new horizontal well drilling, multi-stage fracturing and the stimulation of older wells that have little or no production. Frac sand is needed to “prop open” the fractures in the rock reservoirs to allow oil and gas to flow out more freely.According to the U.S. Geological Survey (USGS), the estimated production of frac sand in 2015 was 71 percent of the total production of industrial silica sand or 67.4 Mt (74.3 million st). This is a decrease of about 12 percent from 2014. However, the silica sand industry and other industry sources estimate only 50 Mt (55 million st) of frac sand were produced in 2015. In recent years both the USGS and industry studies have been very close in estimating the production of frac sand but with the recent downturn in frac sand production, perhaps, reporting to the USGS was not as accurate. These discrepancies may be that the USGS statistics are based on voluntary reporting by the industry and some companies report their approximate production, others may not. It is always difficult to obtain accurate production figures of any industrial mineral or construction aggregate operation as most companies tend to keep those figures somewhat confidential. It is certainly accurate to report that the production of frac sand had decreased since the last quarter of 2014 and through 2015. The oversupply of oil and natural gas has led to this decline in frac sand usage. Oversupply has idled drilling rigs and well completion activities. World Oil Magazine reports that 2015 was the worst year for rigs in a quarter century. The only wells being completed are those that have contract agreements to do so, others have been capped. Very few new wells are being drilled. Since about 98 percent of well completion is sand and water, the sand supply has caught up with the demand. There are some bright spots in the “oil patch” as the Permian Basin in Texas and the Woodford Shale in Oklahoma have kept pace somewhat with drilling and completion. It has been reported that the frac sand producers in the Brady-Voca, TX area are producing to nearly capacity. The northern frac sand producers like those in Wisconsin, Illinois and Minnesota are feeling the downturn because of the cost of shipping sand to these moderately active basins and plays. The “rule of thumb” is that freight is 2/3 and sand is 1/3 the cost."

Jul 1, 2016

By A. B. Cecala

The Bureau of Mines performed a study to determine optimal locations for longwall face methane monitoring equipment. Longwall face ignitions continue to be a concern to the U.S. coal mining industry. Gains in ignition control technology have been somewhat negated by advances in longwall productivity. More reliable, heavy-duty longwall face systems generate higher production rates and increase methane liberation rates. These rates will likely continue to rise in the future as further coal production increases occur. Efforts will continue in the areas of methane drainage, methane containment, and methane dilution. In addition, more effective face methane monitoring is needed. As technology continues toward automated longwall panels, the importance of monitoring for methane at the shearer becomes even more significant. Since the primary face ignition source is the shearer mining machine, the Bureau ran tests to determine the best location to take methane readings on the shearer. This information, in conjunction with data obtained from field studies, provides a knowledge base for selecting optimum face methane monitoring locations.

Jan 1, 1993

By D. Bessinger, J. M. A. Geldenhuis

High titania slag is produced from the smelting of ilmenite. These slags contain approximately 85 per cent TiO2 and consist mainly of a M3O5 solid-solution phase. During cooling the slag can decrepitate to a fine particulate material, which decreases the value of the product. Based on X-ray diffraction analyses of the decrepitated slag after cooling, it was found that the M3O5 phase had almost disappeared. The disappearance of the M3O5 phase was linked to oxidation of the slag. A M6O11 phase formed in the decrepitated slag. It is postulated that decrepitation of high titania slag is caused by volume changes due to the oxidation of the M3O5 phase in the slag.

Jan 1, 2005

More than 100,000 people are expected to be in Las Vegas, NV in March for ConExpo-Con/Agg 2002, the largest exhibit of its kind in the Western Hemisphere. This triennial event features equipment, services and technical sessions geared toward the global construction aggregates and ready mix concrete industries. ConExpo-Con/Agg 2002 will take place March 19-25, 2002 at the Las Vegas Convention Center. For registration information, contact the show offices, phone 800-867-6060, 414-298-4141, or 301-587-3140, Website www.conexpoconagg.com.

Jan 1, 2002

By VIVEK KASHYAP, Evody Tshijik Karumb, PATRICK TAYLOR

The partial reduction of zinc ferrite to zinc oxide and iron (II, III) oxide can enhance the leaching rate of zinc. Zinc ferrite has often been found as a major component of zinc residues and electric arc furnace dust. The Waelz process is an existing process for zinc ferrite processing, which requires a temperature of more than about 1200 °C to produce Waelz oxide containing ZnO. Since zinc residues have been deemed as a potential way for the extraction of zinc and other critical metals, it is important to analyze the reaction kinetics in the temperature range of interest. This manuscript discusses the chemical kinetics of zinc ferrite reduction by hydrogen gas. Several researchers studied the reduction of zinc ferrite with CO; however, unlike CO, the use of H2 gas as a reductant allows partial reduction of zinc ferrite even at low-temperature range (400–600 °C). Thermogravimetric analyses (TGA) experiments were performed in the temperature range of 300–700 °C with 10% and 30% H2, and the data obtained was analyzed using the isoconversional method of kinetic analyses. The standard models used for isoconversional kinetic analysis were chosen from literature and experimental data were fitted to determine the controlling mechanism and calculation of kinetic parameters of reduction of zinc ferrite. The rate of reaction was found to be increasing with an increase in temperature and partial pressure of H2 gas. The reaction could be divided into three stages, where reaction interface contraction was found to be the controlling mechanism at the initial stage of reaction. As the reaction proceeds, product layer thickness increases, and thus, diffusion was found to be the controlling mechanism. Roasting products obtained from TGA experiments were also characterized using a scanning electron microscope (SEM) to verify critical morphological details.

Jul 26, 2022

By William F. Daly, William H. Hansmire

Installation of initial tunnel support is often the most uncertain element of work in the design of, and a contractor bidding on, construction of a rock tunnel. The risks the construction contractor and owner assume are delineated to a great extent in the technical specifications portion of the contract documents. It is intended that this paper identify current practices for specifying initial tunnel support and the impacts each case has on the assignment of risks associated with providing the initial tunnel support. Examples of recently completed tunnel designs are given.

Jan 1, 1985

By Paul C. Schmall, Thomas Tuozzolo, Arthur B. Corwin

The Lenox Avenue Reconstruction Project involved the excavation and replacement of 750 m (2,500 ft) of deteriorated subway invert concrete, 5 to 7 m (15 to20 ft) below water table in very permeable ground. The Replacement work was done over an 8 month period, while maintaining track service through this subway section. The project was dewatered with a single 125 l/s (2,000 gpm) wellpoint system,750 m (2,500 ft) in length, which was installed from inside the active tunnel structure and configured to coexist in the subway tunnel with operating trains as well as the construction activities. A thin diaphragm jet grout wall was utilized on one end of the site to cut off the flow of water across a difficult geological interface that was situated immediately below the tunnel invert. The thin diaphragm jet grout wall permitted the large 116th Street Station area to be dewatered completely with well points from outside of the excavation.

Jan 1, 2001

By J. M. Barker

New Mexico is the leading domestic producer of perlite, a hydrated volcanic glass that can be expanded thermally to form a white, very porous, lightweight material. The United States is the leading consumer and producer of perlite in the world (Pettifer 1981). New Mexico produced, at five mines (Fig. 1), about 86% of all domestic crude ore mined in 1984 (Meisinger, 1985). Perlite is mined in 6 other western states, ore is expanded in 33 states, and the expanded ore is consumed in all states (Meisinger, 1985). Gross value of domestic ore mined in 1984 was about $16,500,000 (FOB mine; Meisinger, 1985) with much value added by expansion and processing prior to sale to end users. In contrast to the ubiquitous nature of perlite products in the U.S. economy, facilities for testing perlite ore, expanded perlite, and perlite products are notably lacking on a commercial, cost-effective, or readily accessible basis. The New Mexico Bureau of Mines and Min¬eral Resources (NMBM&MR) established a perlite¬testing facility in 1984 to mitigate this lack and to further the mining of perlite in the state.

Jan 1, 1985

Let’s start off with your assessment of the mining industry. Today, the status of the mining industry is stronger than it has been over the previous few years. While mining continues to be a major part of the world’s economic foundation, the industry is gaining strength due to rebounding metals and minerals prices. And now, with these rising prices and the changes the industry instituted during the years when mining-related commodities were selling at low prices, our stronger, more productive and internationally competitive industry should flourish. Mining remains an essential business and the industry is far ahead of the game when it comes to the trend of globalization as a key to sustained growth. Also, the industry continues to realize increased productivity through technological innovations. And an increasing number of countries are moving towards capitalism, which opens doors for exploration and mining within their borders. After looking at all of these factors, I believe that the mining industry will only continue to gain momentum in the future.

Jan 1, 2004

By C. Bazin

Grinding circuits are operated in the presence of disturbances due to ore changes and equipment malfunctions. One of the challenges faced by the operators is the detection of a disturbance, the identification of its origin and of the action to correct the problem. Hydrocyclones overloading, worn or partly plugged apexes of the units of a nest, surging and internal liner detachment may cause a loss of classification capacity and quality leading to a less efficient grinding operation. A dynamic simulator is used to assess rules for the diagnosis of hydrocyclone faults from the trends produced by sensors.

Jan 1, 2009

Choosing the right valve for corrosive, abrasive slurry applications requires exacting analysis and a comprehensive understanding of the complete slurry process. Within the realm of flow control in abrasive and corrosive slurry applications, there is no room for a one-size-fits-all approach. To ensure minimal maintenance, maximum uptime and the lowest overall cost of ownership, the slurry processing toolbox must contain countless alloy and elastomeric pairings ? each carefully targeted to the particular process medium and conditions. This materials selection process is best tackled by turning to expert slurry application engineers and valve product managers who work closely with customers to specify the optimal valve for the given parameters. ?When plant operators and design engineers apply conventional valves in abrasive applications or use metal seated valves or simply apply the wrong valve for a particular flow control situation, it typically leads to rapid valve failure, the potential for hazardous leakage, unexpected shutdowns and costly downtime,? said Cal Cobb, valve products manager for Weir Minerals North America, manufacturer of Isogate slurry valves for service in mining, minerals processing and metallurgical environments.

Jan 1, 2011

By William L. Young

I think I should let you in on one of Canada's best-kept secrets, if you will promise not to tell it all over the place. Believe it or not, good, honest, enterprising capitalism is still alive and flourishing north of our common border, and I am living proof that capitalism is still working for the little guy. My personal story of mining development in Canada isn't all that rare -- you've probably heard something like it from other areas and other days several times -- but my case brings it up-to-date. I would like to Tell you briefly the history of Northumberland Mines Limited, a contemporary case of individual enterprise getting a mining operation underway. And if I can do it you probably can too.

Jan 1, 1981

By R. Bishop, J. Baggett, J. Monsalve, N. Ripepi, A. Soni

Technology plays an ever-increasing role in improving the safety and efficiency of mining operations. Laser scanning and photogrammetry are two useful methods for capturing 3D digital representations of real world objects. While both technologies have been applied to the mining industry in numerous ways, the practical applications in an operating underground limestone mine has been tested for this paper, including for visualization and site characterization. Each technology is capable of creating highly detailed geospatial point clouds, but are all point clouds created equal? This paper presents a comparison of a laser scan and photogrammetry of a limestone pillar and addresses the strengths and limitations of each method for creating digital models of operating underground limestone mines. INTRODUCTION The United States crushed stone business is a ~$14 billion per year industry representing 1,430 companies which operate 3,782 mining operations across the 50 states. In 2017 alone, 1.33 billion tons of crushed stone was produced with 76% used predominately for road construction and repairs, but also for the production of cement, lime, chemical and agricultural uses. Over 70% of domestic crushed stone producers source their material from limestone and dolomite deposits, with currently only 82 mines (2%) operating underground (USGS, 2018). Underground mining requires a different technical skillset, and poses great challenges for production that must be both safe and economical. Therefore, there are many risks that an operation must mitigate in order to produce underground limestone. Some of the challenges in underground limestone mining involve geological hazards that are unique to the rest of the industry. The geologic features such as faults and weaknesses can be difficult to assess in a production environment (NIOSH, 1998). The consequences of failure due to improperly designed underground mining ground support systems, such as from a roof failure, are not only life threatening for the miners themselves, but can easily shut down an entire mining operation.

Jan 1, 2019