Search Documents

By Felicia F. Peng

One of the serious environmental problems related with the extraction of coal for carbon and energy resources is that upon preparation of coal a large quantity of fine coal has been discarded and/or lost to tailing impoundments. These problems present hazardous conditions to the local community. Also, the precious heating value of energy resources has been wasted and Left unrecovered in the tailing impoundments. Both RCR and SMRC ACTs recognize and mandate an investigation into slurry impoundment problems, including consideration of potential use of those coal fines in the tailing ponds. Bituminous coal producing district 46 encompasses the northern panhandle of West Virginia. The major producing seam in this district is the Pittsburgh coal, 1-7 meters thick. 75 percent of the coal producted in this district is deep mine. This district produces approximately 3 million tons of coal waste materials annually. One of the coal preparation plants in the district which we have visited has been processing Pittsburgh too. 8 seam coal for the past ten years. The characteristic data of the Pittsburgh raw coal is shown in Table 1. The raw coal produced in this district is characterized by its high heating value, high ash and high sulfur contents. The coal preparation plant flowsheet designed and used to process this Pittsburgh raw coal prior to 1979 is shown in Figure 1. It was a partial coal cleaning plant' with 1 092 mt/hr designed capacity, which consisted mainly of a coarse coal cleaning circuit. The rejected fine particles in the size range of -600µm which consisted of vorsiv underflow and cyclone underflow from clean coal streams and spiral classifier overflow from refuse stream were settled down in a thickener with the aid of anionic flocculant prior to being pumped to the tailing ponds for disposal. Figure 2 shows that the same coal preparation plant in Figure 1 was modified to a semi-complete coal cleaning plant and expanded its designed capacity to 1 820 mt/hr, when market of coal fines becomes feasible in 1979. Tabling in the clean coal circuit and thermal dryer in the dewatering circuit were added to the flow sheet. The purpose is to recover more coal fines, reduce more pyritic sulfur and ash contents in coal and also to reduce solid waste material to be stored into the slurry impoundment, giving them a Longer Life. The rejected fine particles fed to the thickener are clean coal fines from two cyclone overflows and the fine refuse from the rufuse cyclone overflow. The clean coal fines presently lost to the tailing impoundments are in the size range of -150 µm and constitute about 5 percent of the overall plant feed. Total amount of tailing waste material accumulated in a tailing impoundment is estimated at 1.3 million metricton for the past ten years.

Jan 1, 1982

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk, T. Punt

This study investigated the performance of citric acid as lixiviant for cathode material from end-of-life lithium-ion batteries (LIBs). Black mass containing 84.2 weight percent MNC (LiNi0.45Mn0.4Co0.15O2) and 15.8 weight percent LCO (LiCoO2) material was leached at solid-to-liquid ratios of 20, 50 and 100 g/L. Leaching with 1.5 M citric acid, 2 volume percent H2O2 and a solid-to-liquid ratio of 20 g/L at 95 °C extracted 90 percent Co, 95 percent Li, 94 percent Mn and 94 percent Ni within 20 min. At the highest solid-to-liquid ratio of 100 g/L with 1.5 M citric acid, 10 volume percent H2O2 and 95 °C, 84 percent Al, 84 percent Co, 87 percent Li, 86 percent Mn and 96 percent Ni were leached after 40 min, producing a leach solution containing 0.68 g/L Al, 20.0 g/L Co, 6.0 g/L Li, 13.6 g/L Mn and 19.3 g/L Ni. Using stepwise addition of H2O2, instead of initial bulk addition, did not significantly improve the leaching efficiency but did reduce the required leaching time. Temperature control of the reactor was also more manageable with stepwise addition of H2O2, and evolution of gas was less vigorous. It was observed that the leaching efficiencies of Co, Li and Mn decreased slightly at solid-to-liquid ratios of 50 and 100 g/L, while the leaching of Ni increased slightly. The solution leached at 20 g/L could be stored for six weeks without any spontaneous precipitation. However, solutions leached at 50 and 100 g/L showed changes in concentration after one month of storage, suggesting that processes that have a large material throughput and use high solid-to-liquid ratios around 100 g/L must ensure that the solutions are not stored for extended periods of time.

Apr 1, 2025

By Vincente M. Jr. Lim, Brain W. Lawrence

Underground mining operating costs consist pri¬marily of direct costs such as labor, supervision, ma¬terials, and supplies, plus indirect costs. The material and supply costs vary substantially between mines but commonly range from 35 to 60% of the total direct costs. As part of the preparation of accurate operating cost estimates for a project, information must be as¬sembled to select the material and supply items and to determine the quantities of these items that will be required. Cost data then can be incorporated with the estimated material and supply requirements to determine the total material and supply costs for the project. Estimated quantities will vary considerably between mining projects depending upon factors such as the type of material being mined, the mining method, the equip¬ment selected, drilling and blasting techniques, mucking and haulage methods, ground support requirements, number of men employed, etc. Valuable information often can be obtained from suppliers and manufacturers, including data on current operating practices for similar projects, recommenda¬tions for the specific project, and preliminary cost quota¬tions. However, quotations obtained for estimates are generally higher than the prices paid at the time of purchase. Mines operating in the area, or those mining under similar conditions, also can provide essential design information, but it often is difficult to obtain cost information from the operators. Estimated costs for the most common major items of underground materials and supplies are presented in the accompanying tables. They represent current costs or cost ranges and are intended to be used only as a guide when preparing budgetary estimates for materials and supplies. Cost data were obtained mainly from suppliers and manufacturers, with up to three quotations being ob¬tained for each item whenever possible. In most cases, as noted in the table footnotes, prices were based on quantities representing normal requirements for me¬dium-size mine operations. Every attempt was made to assure accuracy. However, the cost for most items, especially those with multiple sources, can deviate sig¬nificantly for various reasons such as geographical loca¬tion, current market conditions, quantities ordered, size of the customer (which could influence the ultimate quantities purchased), and the ability of the purchasing department. It is also for these reasons that the actual amount individual mines are now paying for specific items may vary from the estimated cost in the tables. The cost for specific sizes of items that do not appear in the tables often can be factored from the data pre¬sented. Costs for many items can be converted easily to a unit that sometimes is more basic, but not as com¬monly used, such as from a length to a weight unit. Other items not listed, such as repair parts for equip¬ment, will involve contact with suppliers to determine specific recommended requirements and to obtain costs for these items as related to each individual project. Costs are expressed in terms of US dollars as of 1978 unless otherwise specified. All measurements, sizes, and weights are expressed in conventional units (i.e. feet, inches, pounds) ; applicable metric conversion fac¬tors follow each table. Costs are represented for drill steel and bits; mining explosives; blasting caps; blasting supplies; ground sup¬port items; ventilation equipment; utility pipe, utility hose, and accessories; mine track and accessories; tires for underground equipment; lubricants and fuels; and miscellaneous supplies.

Jan 1, 1982

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By Don Phelps, Christopher Tattersall, David McAllister

Located south of downtown Seattle, the Beacon Hill Station & Tunnels is the key section of the southern segment of Sound Transit’s proposed new LINK light rail system. This paper presents an overview of the design, which includes 4,300 ft of segmentally-lined bore twin tunnels and a deep mined station. With platforms located156 feet below grade, the station itself is only the second large-scale mined station in soil the US. Its complex geometry combined with variable soil conditions—sands, silt sand clays with slickensides—challenged the designer’s to come up with a SEM-based design that addresses the owner’s risk, cost and schedule concerns.

Jan 1, 2003

By John A. Shuster

Case histories are reported for several soft ground shafts ranging from 6' to 40' in diameter and 50' to 230' in overburden depth for which ground freezing was employed to provide temporary ground support and groundwater control during shaft sinking through the overburden. Cases reported emphasize dealing with difficult site and ground conditions such as working within existing buildings, through very soft, running and bouldery soils, in the presence of substantial lateral groundwater flows, and into salt dome deposits requiring special considerations. Construction procedures, schedule, and relative costs are discussed for each case.

Jan 1, 1985

By A. K. Kelly

Potash was first discovered in Saskatchewan in 1943 but its continuous extraction did not begin until 1962. In the years since then, potash has played an important role in the economic and political life of the province. And, as is well-known, the most eventful time in the life of the industry occurred in 1975 when the Government of Saskatchewan decided to become a major participant in potash production. To understand that decision, however, requires an understanding of the economic development of Saskatchewan and of relations between the industry and the government prior to 1975. This year, Saskatchewan celebrates its 75th year as a province. For most of those years, we have been an agrarian economy and society, dependent on exports of cereal grains, mostly wheat, for a livelihood. Even today, agriculture accounts for about 25% of the province's Gross Domestic Product (Economic Review, 1979, p. 7) and difficulties in agriculture spread rapidly to the rest of the provincial economy. The difficulties and risks that go hand in hand with being a "one crop" economy were known as long ago as 1920 but were not fully appreciated until the combination of depression and drought in the 1930's turned the prairie grain- belt into a dustbowl. Some idea of the severity of the depression is revealed by the following data: in 1928, Saskatchewan produced 321 million bushels of wheat. By 1931, the total fell to 132 million bushels and, in 1937, to a mere 37 million bushels. The value of agricultural products sold off farms fell from $273,000,000 in 1928 to a meagre $51,000,000 in 1937. The impact of such a fall of agricultural incomes was catastrophic since about 70% of the population of some 921,000 persons lived in rural, agriculture-dependent areas (Britnel.1, 1939, p. 14).

Jan 1, 1980

By Paul T. Allsman, Paul F. Yopes

17.1--CURRENT AND FUTURE STATUS OF SURFACE MINING PAUL T. ALLSMAN AND PAUL F. YOPES 17.1.1--CURRENT The history of surface mining essentially is one of mining coal, copper, iron and aluminum ores, of placer mining gold and tin, and of pits and quarries producing clays, gypsum, phosphate rock, sand, gravel and stone. Table 17-1 is a summary of the estimated world and United States production of crude metallic and non¬metallic ores and coal in 1969. It includes estimates of the quantities produced by surface-mining methods. Two-thirds of the 10 billion tons are mined from the surface, ranging from a third of the coal. 57% of the metallic ores, and nearly all clays, stone, sand and gravel. Production by surface methods in the United States, parallels that of the world with one exception: about 90% of the copper and iron ore is mined from the surface, whereas elsewhere only about half the copper ore is surface mined. In Canada, surface mining of the Athabasca tar-sand deposits is a recent large-scale unique operation. In surface mining of coal and, to a lesser extent, metallic ores, much waste is stripped, but in nonmetallic pits and quarries the ratio between waste and ore usually is small. Assuming that the stripping ratio for surface mining in the

Jan 1, 1973

By G. Van Weert

Refractory ores and concentrates containing silver tend to form Ag-jarosite during autoclave oxidation. Silver extraction from the oxidation products is therefore low, unless a hot lime treatment step to decompose Ag-jarosite precedes cyanidation. Since silver iodide is very stable but soluble in cyanide solutions, the formation and decomposition of Ag-jarosite in the presence of iodine species was studied. Results indicate that Ag-jarosite formation could be prevented in favour of H3O-jarosite and AgI while oxidizing Ag2S under industrial autoclaving conditions, when the total iodine species to Ag mole ratio exceeded 5. Lower ratios gave proportionally more Ag-jarosite and less AgI. Under these conditions existing Ag-jarosite was also found to decompose in H30-jarosite and AgI.

Jan 1, 1993

By Ralph L. Merklin

One of the most commonly employed set of calculations in mill design and research is the material balance, known in wet beneficiation plants, as an Ore and Water Balance. For mill designers, the balance is one of the principal requirements in determining the proper size of launders, pipelines, process equipment, etc. In process development, one of the major goals is the establishment of an optimum balance. The usual procedure for calculating a material balance involves a manual technique utilizing reference tables, pre -obtained data, and a slide rule or desk calculator. With these, the engineer must perform a series of calculations which are repetitious in nature and time consuming. Figure I is the flowsheet of the grinding and flotation circuits for a copper concentrator. The initial ore and water balance was calculated manually and required approximately 24 manhours. Later, a number of changes were made in the balance, each of which required an average of 8 manhours.

Jan 1, 1967

By Ronald P. Wright

ARAMIDS UNDERGROUND COAL MINING

Jan 1, 1993

By R. C. Bunge

The success of a mineral separation is commonly assessed from the separation curve, a graph of the recoveries achieved versus the corresponding separator settings. Two values characterize the curve, first the "splitpoint" which is the separator setting that produces a recovery of 50%, and second a measure for the separation sharpness. The splitpoint represents the "mean" while the measure for the separation sharpness represents the "scatter". In modelling the performance of crossflow separations the mean particle behavior is calculated from the force equilibrium that determines the particle trajectory which leads to a deterministic model. The scatter is then represented by a stochastic model. This presentation discusses the modeling of a crossflow separation and some implications with separation theory. The model is shown to successfully predict the performance of a magnetogravimetric separator.

Jan 1, 1992

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Mahesh C. Jha, Frank J. Smit

Column flotation and selective agglomeration are promising advanced physical cleaning processes that can be developed for preparing premium quality coal-water slurry fuel from coal fines. Such a fuel could either replace oil or natural gas in certain industrial and utility boilers or else could be burned in advanced combustors currently under development. These applications require coal cleaned to sulfur and ash contents below 258 g/GJ and 430 - 860 g/GJ (0.6 lb/million Btu and 1 - 2 lb/million Btu), respectively, to meet clean air emission requirements. A highly loaded slurry must be produced in order to avoid derating the boilers, and the total cost of the fuel must be below $2.37/GJ ($2.50/million Btu) in order to penetrate the market by the turn of the century. Achieving these technical and economic goals depend critically on the selection of suitable feed coals. This paper describes the identification and evaluation of 18 coals and final selection of six coals from different regions of the United States as potential feedstock for preparation of premium fuel. The work is being performed under a cost-shared DOE project.

Jan 1, 1995

By Gunnar Nord

Shifting ground conditions when tunnelling often call for different methods of attacking the tunnel face. In order to overcome problems with local unstable soft ground in a hard rock tunnelling project the Boodex method offers a cost effective alternative. Boodex and variants of it is a combination of two well-known techniques, drilling with Boomer rig using Odex gear. It will give a steel lined hole ready for grouting and the steel pipe has a load bearing capacity that means that a spiling effect is achieved. In this paper the method and some applications will be described with possibilities and limitations.

Jan 1, 2003

By K. Katen

In another situation, Dave Zegeer, the Assistant Secretary of Labor for Mine Safety and Health, whom all of you know very well, would have taken the opportunity to talk with you. In his absence, however, I would like to reference some of his recent comments which may help us to see the issue of mine safety in historical perspective. Dave pointed out that this year is the eightieth anniversary of the Great Earthquake and Fire of San Francisco. The whole world heard about that disaster--it and the 452 people who died in it. In that same year, nearly five times as many people died in coal mines, but no one particularly noticed.

Jan 1, 1986

By E. Karampinos, P. Morissette

"INTRODUCTION Ground support is a critical element in maintaining the stability of mining drives in deep and high stress mines. In challenging ground conditions, it is necessary to continuously explore ground support strategies that can control the resulting large deformations. It is an objective of mining operations to optimize the ground support by selecting both appropriate systems and the time of installation of each reinforcement element. A successful ground support strategy will result in the use of a system that ensures both the structural and operational integrity of the excavations and mitigates the need for rehabilitation. Preliminary ground support design is often based on empirical observations and methods. Once a design is implemented, field trials, observations and in situ pull tests are used to fine tune or improve the design. Although not often employed during this process, numerical modelling can provide helpful insights on the impact of different ground support strategies. In this respect, it is possible to explore the use of multiple options before selecting the most promising ground support system for implementation in field trials. The challenges associated with the numerical modelling of rock support for mines have been described by Lorig and Varona (2013) and Potvin (2017). The employed numerical models should capture all potential failure modes of reinforcement over the mining sequence of the excavation. In particular, it is important to emulate the observed in situ ground support performance, as well as the influence of the installation sequence of the support. However, the time and expertise required for this type of modelling of ground support is not often available at mine sites. Even when the expertise is available it requires a major time and commitment of resources to set up, run and calibrate the sophisticated models capable of explicitly capturing the behavior of ground support. Rock reinforcement is an integral part of all ground support systems used in underground mines. Long flexible tendons can reinforce the rock mass deeper into the walls and create a thicker reinforced shell around the underground excavation. This paper focuses on the optimization of the cable bolting strategy in squeezing conditions at the LaRonde Mine by integrating the 3D distinct element method (DEM) in the design process. A calibrated numerical model is used to investigate a series of cable bolt configurations and provide recommendations for the ground support design."

Jan 1, 2018

By J. A. Siekmeier

The thickness of the laminated beam modeled in this study is based on bridging potential and TDR measurements. The laminated beam stiffness is based on the effective stiffness of an equivalent transformed section. The maximum deflection of this near-surface laminated beam is compared with the maximum measured surface subsidence. The spreadsheet provides a rational technique to graphically display the character of the overburden and potentially allows prediction of a subsidence factor based on boring logs and the proposed mine plan. The U.S. Department of the Interior, Bureau of Mines (Bureau), utilizes a commercially available computer spreadsheet program in combination with a modified version of Bieniawski's Rock Mass Rating (RMR) system to characterize the geology overlying high extraction coal mines. The spreadsheet program calculates a RMR for each bed based on the lithology, thickness, and engineering properties, which are determined from boring logs and laboratory tests. Once the RMR is calculated the spreadsheet has two major functions. First, the spreadsheet calculates values used to graphically represent the character of each individual bed in the overburden. It calculates an in situ deformation modulus using an empirical rela¬tionship between the modulus and the RMR and then uses this effective modulus along with additional parameters that are based on mine geometry to calculate the bending stiffness and bridging potential for each bed. Second, the spreadsheet creates a transformed section that allows groups of beds to be modeled as an elastic beam. It then calculates a bridging potential for the entire rock mass. The bridging potential of the rock mass is a single value that takes into account both the geology of the overburden and the geometry of the mine. It seems reasonable that there would be a strong correlation between the bridging potential, the overburden response to high extraction mining, and the subsidence ratio. The results presented in this paper focus on the relationship between the bridging potential of individual beds and the deformation measured using Time Domain Reflectometry (TOR). Subsurface displacements measured over seven high extraction coal mines in southern Illinois were correlated with the bed stiffness and bridging potential profiles. Based on these correlations it was evident that the process of caving and subsidence over these high extraction mines involved momentary bridging by individual beds or groups of beds and the ultimate development of a laminated beam near the surface.

Jan 1, 1986

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calcula¬tions where the compliance limit of lbs S02/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equa¬tions to blend to an SO2 content of 1.2 lbs S02/million Btu; the excess sulfur for Coal A was defined as Sulfur excess%o = 0.5 - 0.6-13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C<- 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: ? W is the total weight; ? A, B and C are the fractional proportions of each potential blend stocks; ? Sa, Sb and Sc represent the percent sulfur content of the blend stocks; ? Ha, Hb and He represent the calorific content of the blend stocks in Btu/lb; and ? H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1997

By A. Subbotin

During developing the Ingulska mine at the Mi-churinske uranium deposit in the central part of Ukraine the radioactive rock dumps have been piled. A height of dumps reaches to 15-25m. They occupy a large territory and can be a source of covering with radioactive dust the area around the Ingulska mine. Uranium content exceeds 0,01% in all dump rocks samples while in the dust fraction samples it ranges from 0,01 to 0,06%. Uranium content in road dust at the dump?s foot reaches 0,137%. A new (for Ukraine) method of f-radiography of tree and bush leaves sampled at the territory about 100km2 has been used. It is based on fission of 235U nucleuses due to heat neutron influence in a nuclear reactor and on following study of the Lausan films with tracks drawn by the fractures of these nucleuses. Uranium content of the dif-fusion-disseminated dust type is (0.9-22.2)?10-6% while in the individual particles it can be considered much more because of burned holes in Lavsan above them. The dust content with uranium in Kirovograd reaches to 20-50 part/cm2 while near the dumps it ranges from 100 part/cm2 to 300 part/cm2 in the radius of 1,5-2km from the Ingulska mine.

Jan 1, 2005