Search Documents

By Donald A. Ranta

Every mineral project or mine is based on a geologic entity-an ore (mineral) deposit. A well-defined mineral deposit and its associated geologic characteristics are the only aspects of a project that cannot be altered. Mine plans can be modified to exploit the deposit using alternative approaches and yielding similar results. A variety of processing methods also are often available producing generally comparable results. Major modifications can be made to other aspects of the project without substantially changing project economics. However, all engineering and metallurgical aspects of a mine must be accommodated to the spe¬cific location and geologic characteristics of the deposit. Geologic data and interpretations form the foundation for both mine evaluation and mine production by providing esti¬mates of reserves and essential information for mine planning and process design or control. Proper geologic work requires a keen awareness of and an ability to anticipate the technical requirements of geotechnical engineers, hydrologists, mining engineers, metallurgists, and other specialists. Geologists are inte-

Jan 1, 2008

By Jr. Abel

Subsidence is controlled by a complex combination of mining and geologic factors. For example, a world-wide compilation of data shows that, as the percentage of shale in the overying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the overburden appears to cause as much as a three-fold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted the smaller percentage of that thickness that shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room and pillar panels is dependent on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1980

By Daniel M. Flanagan

"Editor’s note: Each year, Mining Engineering features an industrial minerals review. Several people put in a fair amount of time in developing the material for this issue, all the while doing their own jobs. Thank you to the industrial minerals annual review editor, to the Industrial Minerals & Aggregates Division technical committee chair and vice chairs, and to the authors of the individual commodity profiles. Jim Norman, member SME, of Tetra Tech, is the industrial minerals annual review editor.Joe Garska, member SME, of Imerys, is chair of the Industrial Minerals &Aggregates Division’s Technical Committee.The technical committee vice chairs include:• Hyunjung Kim, member SME, of Chonbuk National University, agricultural materials.• Xihui Lin, member SME, of Kemira, ceramics and refractory materials.• Nikhil Gupta, member SME, of Virginia Tech, chemical raw materials.• Adam Rodriquez, member SME, of Penn State, construction aggregates.• LeDeana Roberts, member SME, of Imerys, fillers and pigments.• Harsha Kolla, member SME, of ChemEOR, sorbents, filters and process aids.• Edgar Blanco, member SME, of FLSmidth, specialty minerals.Their help makes possible this July industrial minerals issue. On behalf of ME readers, the editors thank them.During the past 25 years, U.S. ball clay production (the quantity sold or used by domestic producers) increased from 788 kt (869,000 st) in 1990 to an alltime high of 1.31 Mt (1.44 million st) in 2003 (Fig. 1). Housing construction within the United States, a leading market for ball clay-based ceramics and sanitaryware, began to decline in 2005, which resulted in a considerable decrease in sales of ball clay that continued through the 2008-2009 economic recession. After bottoming out at 831 kt (916,000 st) in 2009, ball clay production steadily increased through 2015 (Fig. 1). Estimated sales in 2015 were 36 percent higher than those in 1990 and 18 percent lower than those in 2003.Four companies (H.C. Spinks Clay Co., Imerys S.A., Old Hickory Clay Co., and Unimin Corp.), mined ball clay in five states during 2015. An estimated 1.7 Mt (1.18 million st) of ball clay valued at an estimated $47.5 million was sold or used by U.S. producers, a 4-percent increase from 1.03 Mt (1.14 million st) valued at $45.2 million in 2014. Approximately 65 percent of total ball clay production was air-float, 25 percent was crude or shredded and 10 percent was water-slurried"

Jul 1, 2016

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Mahmut Yavuz

to in Old Uighur Turkish as Tolay kopugu, in Ottoman Turkish as Derya kopugu, and in modern Turkish as Luletasi. Scientifically known as sepiolite, it is represented by the formula Si12Mg8O30(OH)4(H2O)4(8H2O). Sepiolite is a natural clay mineral composed of hydrous magnesium silicate, characterized by a structure of alternating blocks and tunnels that develop in the direction of the fiber. Each structural block contains two silica tetrahedral sheets surrounding a central layer of magnesium oxide- hydroxide. Sepiolite exists in two distinct forms in nature: alpha-sepiolite and beta-sepiolite. Alpha- sepiolite is amorphous, compact, and resembles pellets that look like sea froth, hence its Turkish name Luletasi. In contrast, beta-sepiolite appears as amorphous aggregates or small, flat, round particles. These two forms exhibit different physical properties. Meerschaum was also studied by Brauner and Preisinger in 1958, who agreed that it primarily consists of sepiolite (2MgO·3SiO2·nH2O). According to these researchers, water is present in its mineral, zeolitic, crystal, and structural forms. Meerschaum is commonly used for adsorbing various liquids, as an ion exchanger, and for dispersing and insulating paraffin in the chemical industry (Gokdemir and Dogan, 2011). Sepiolite deposits of the meerschaum type are primarily found in Turkey, Somalia, Tanzania, Kenya, and Mexico. Alongside high-quality, low-density, and highly porous meerschaum, Somalia also has sedimentary sepiolite formations. The total reserves of these deposits are estimated at around 50–100 million tons (Sariiz and Isik, 1995). Meerschaum, also known as “white gold” or “sepiolite,” is a unique mineral highly prized for its lightness, heat- resistant properties, and ability to be carved into intricate designs. Found predominantly in Eskisehir, Turkiye, meerschaum mining and processing have become significant contributors to the local economy and cultural heritage. This paper explores the history, economic importance, mining practices, and environmental impacts of meerschaum mining in Eskisehir and discusses the challenges and opportunities faced by the industry.

Feb 1, 2025

By Sean Masse

New Gold?s New Afton Mine, located 8 km (5 miles) west of Kamloops, British Columbia, is a 4.5-Mt/a (5-million stpy) block cave mine, making it the highest tonnage underground hard rock mine in Canada. The reserve is estimated at 52.5 Mt (55.9 million st) with grades of 0.65 g/t (0.02 oz/st) gold and 0.93 percent copper (2012). Commercial production was achieved in July 2012 and nameplate production was achieved ahead of schedule in September 2012, with the cave breaching to surface in 2013. The mill has a SAG and a ball mill with a froth flotation circuit.

Jan 1, 2014

By W. R. Reed, G. W. Luxbacher

As directed by the MINER act of 2006, the NIOSH Office of Mine Health & Safety Research (OMSHR) has annually awarded contracts to enhance mine safety and health. OMSHR has a history of research that focuses on both respirable coal mine dust and respirable crystalline silica (or quartz) dust, and contracts have been awarded since 2010 in support of our intramural research efforts. In 2018, a National Academies of Science consensus study report recommended expansion of respirable dust research. As a result, beginning in 2018 through 2021, eighteen contracts were awarded focusing on this area. These contracts can be grouped in three topic areas: characterization of coal/dust, development of real time monitors, and improvement of respirable dust controls. This paper summarizes the outcomes of completed contracts and the progress of current contracts.

Mar 2, 2022

By P. K. Chatterjee, G. D. Just

Sublevel open stoping is a low-cost method that has been successfully employed in many large underground mining operations. Where ore body characteristics are suitable, extensive mechanization and the use of large-scale stoping techniques can considerably reduce operating costs. However, careful long-term planning of mine layouts and large capital commitments in development are required prior to production. Implementing precise mine design procedures and carefully controlling operations can result in considerable benefits. This article describes methods to achieve these objectives based largely on mining operations at Mount Isa, where sublevel open stoping has been used since 1932. Ore won by this method accounted for a very large percentage of the total tonnage produced at Mount Isa. Major costs associated with sublevel open stoping can be classified as drilling, explosives and charging, and LHD costs. In this article, analyses of these costs are made with particular reference to stope design. Parameters such as burden, drill hole diameter, explosive density, specific charge, etc., are considered in establishing the interrelationship of unit operating costs, as well as total costs of sublevel open stoping.

Jan 10, 1981

By Michael E. Zellars

The distribution of phosphate in Pliocene-Miocene deposits of the Southeastern United States was controlled by the prevailing geologic setting. For each basin a unique set of conditions in terms of relationship of land mass to shelf, depositional environment and seawater composition, and movement controlled phosphate distribution. Concentration sufficient to recognize the deposits as a resource occurred in lagoons or shallow neritic zones, with clastics and carbonates diluting the section basinward. Each deposit within a basin displays similar metallurgy and lithology, notwithstanding post-depositional alteration.

Jan 1, 1978

By J. O. Stephens

During the late 1940's and early 1950?s, the Westinghouse Combustion Turbine Division built and demonstrated a residual oil-burning locomotive on six eastern railroads. Plans were made to convert to burning pulverized coal, and a single combustor was operated at a full-pressure condition in the laboratory for about two years. During the mid-1960's to mid-1970's, there was considerable interest in coal-burning MHD and a combustor was developed which would also be applicable to combustion turbines. In the early 19801s, the BCR National Laboratory (BCRNL) became affiliated with the University of Pittsburgh, and a program was begun, supported by the Stare of Pennsylvania, to develop an all-purpose combustor for use with industrial and utility boilers and eventually with combustion turbines. In this paper, we review the work of almost 40 years, indicate our present position, and propose steps to be taken leading to efficient and environmentally acceptable power generation from coal, and specifically to coal-burning locomotives.

Jan 1, 1986

By N. Akbulut, A. Anani

From the initial planning phases to the closing of a mine, mining is an industry where high attention, care, and sensitivity are needed in every step of the mine life. Since mining projects have a long-life span, exceeding a decade sometimes, managing a whole mine project is challenging, especially when challenges faced due to generational differences are considered, such as tracking and logging data, or the usage of different engineering solutions change over time. Along with the overall hardship caused by the time put into a mining project, the present-time operations are very costly where each minute counts. In present-time operations, every decision made, and every minute used during planning and operations has an impact on the efficiency, safety, and economics of the project. Having extremely harsh conditions in both the excavation and mineral processing operations not only slows down the processes but creates very dangerous environments that need to be handled with precise safety measurements. To support the already established processes, we could implement new technologies and use them to our advantage. Virtual reality (VR) is one of these technologies that we could implement in the mining industry. VR is a technology that emerged in the 1960s creating virtual environments and platforms. The user experiences these virtual environments from head- mounted headsets to rooms with 360 screens, all with different levels of immersion. These higher levels of immersion, create a higher level of presencemaking the users more engaged in the activity they are trying to accomplish. These two factors of immersion and presence are what make VR unique and beneficial. VR has some applications and case studies in the industry along with some research being conducted in universities. Unfortunately, there has not been a comprehensive literature review or analysis regarding only VR and its implementations for the mining industry in the last 5 years. This paper aims to describe what VR is and its relation to the mining industry, in the most recent years. The paper first gives a brief background on what VR is and its key concepts. Secondly, it will give information on how the initial stages of the literature review were conducted and the findings along with discussions. The paper will finish with the conclusion drawn from the discussion and potential future work.

Feb 1, 2023

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.

By V. Rajaram

Rock reinforcement systems are used in open pit and underground mines to stabilize the rock mass in-situ and provide safe working conditions. Significant progress has been made to date in the design and implementation of rock reinforcement systems to accommodate bad rock conditions and larger excavations. However, the rationale for the design of rock reinforcement systems remains essentially the same and can be categorized into three groups, namely 1. to create a beam of competent rock in stratified formations, 2. to resist sliding motion in jointed rock, 3. to passively support the superincumbent loads in highly stressed ground. Case histories of the rock reinforcement sys¬tems that illustrate these design approaches will be presented in this paper.

Jan 1, 1983

By K. S. Gritton

The U.S. Bureau of Mines has investigated methods for extracting metals from a variety of arsenic-containing smelter flue dusts. One proposed flowsheet includes a sulfuric acid leach, a cooling step to precipitate hydrated copper sulfate, and a reduction-precipitation of As2O3. Arsenic extractions greater than 90 pct were achieved, while copper extraction ranged from 50 to 85 pct under the conditions examined. Copper was removed from the leach solutions by crystallization followed by SO2 precipitation of arsenic which resulted in a 98 to 99.9 pct As2O3 product. Other metals, such as lead and zinc, were concentrated in the leach residue or in other byproduct streams for recovery of their valuable metal contents.

Jan 1, 1990

By R. A. Matuszak

Throughout the history of power excavating machines, engineers have continuously tried to shape the main drive speed-torque characteristics to provide an optimum performance from each main motion. Selection of prime mover for the various motions has been the subject of many engineering studies and most forms of energy conversion have been tried. A new form of electrical power conversion looms on the horizon' as the most optimum yet. Controlled frequency operation of a squirrel cage induction motor increases the reliability of the most reliable form of energy conversion (electrical) found thus far and at the same time improves the performance characteristics.

Jan 1, 1977

By Pratama Mochamad Rizki, Andika Satya

High-risk area in open-pit mining should always be monitored by the operational supervisor because of its nature. One of this type is the soft soil dump area. Due to the unstable bearing capacity of the soil, it’s highly possible for us to find cracks in the area. This paper aims to build computer vision which able to detect truck’s distance from safe limit allowed during dumping activity. The system will warn the truck’s driver if the truck has crossed that predetermined safe limit.

Jun 25, 2023

By Vhutali Carol Madanda, FHATUWANI SENGANI, François Mulenga

The first introduction of fuzzy theory in the nineteenth century created room for continuous research and application in various fields. Fuzzy set theory has been globally applied in geotechnical engineering, and research in this field continues to date. The fuzzy inference system is considered to be one of the most popular techniques adopted to resolve some of the geomechanical challenges faced in both surface and underground excavations. This paper unpacks fuzzy theory-based approaches in mine geomechanics with the aim of expanding the innovative application of the same approach specifically in tunnel geomechanics. This aim was achieved by conducting a review of recent successful and unsuccessful applications of fuzzy inference systems in underground excavations/tunnelling geomechanics. Indeed, this review has outlined some cardinal points associated with the ability of the technique to solve complex geomechanics problems. However, the success of the technique was accompanied by a few limitations associated with the methodology. Finally, a future outlook associated with the technique has been established.

May 15, 2023

By R. E. Scheffel

Most supergene copper heap leach operations today employ forced-aeration, irrespective of ore grade. Unfortunately, there is little published quantification of its benefit. There is a natural desire to strive for the ideal chemical kinetics. The reality, however, is that physical mechanisms control the commercial extraction rate. This paper presents the performance of a number of operations, their operating conditions and physical ore characteristics, which contribute to non-ideal solution distribution and variable extraction rate. Regardless whether one uses forced-aeration, commercial experience to date suggests it is prudent to design for longer leach cycle times to ensure the production target is met.

Jan 1, 2006

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By J. Kretschmann

Mining heritage can be of outstanding value for many regions around the world, because mining has been done for thousands of years for the benefit of mankind and its development. This paper presents an ongoing project creating a general guideline for the handling of mining heritage on the basis of experiences made in Germany. Interactions of stakeholders in the ?heritage network? as well as strategies for the technical proceeding will be described. An action plan for the sustainable handling of mining heritage has already been developed in part, which includes necessary measures. Best-practice recommendations will be derived. Keywords: m ining heritage / preservation / guidelines / action plan / Sustainability

Feb 27, 2013