Search Documents

By S. Aktas

The present work describes an investigation of a hydrometallurgical process for the recovery of mercury from spent silver oxide button cells. The cell paste was leached in nitric acid to solubilize silver, mercury and zinc. The optimum leaching conditions, in which mercury is entirely converted to Hg2+ ions and, therefore, does not co-precipitate with silver chloride during treatment with potassium chloride solution, were 1.0 M HNO3, 45° C, 1 hour and 200 rpm. After the silver was removed from the solution, mercury was cemented out with zinc powder with an efficiency greater than 99%. In the cementation experiments, the amount of zinc powder, shaking rate, temperature and solution pH were investigated in detail. The mercury recovery (%) increased as the amounts of zinc powder and the temperature were increased. Zinc hydroxide was precipitated from the waste solution by the addition of sodium hydroxide. The Zn(OH)2 precipitate was then converted to zinc oxide. The proposed process is proven to be simple, straightforward and environmentally friendly.

Jan 1, 2011

By A. Ferreira Morgado

The sodium smectitic clays (bentonites), have more industrial applications in that class of mineral, a driving force to obtain this mineral. In Brazil, there are several occurrences of smectitic clays, unfortunately they are polycationic, with a distribution of several exchangeable cations, where the cation sodium occurs in minor quantity. In this work, the original polycationic smectitic clay was firstly proper characterized and then treated with sodium carbonate obtaining homoionic sodium smectitic clay. The rheological tests in the optimized sodium smectitic clay showed good results for drilling fluids, typical of a sodium bentonite ones.

Jan 1, 1999

By Robert W. Bartlett

Heap biooxidation of sulfidic refractory gold ore requires large amounts of oxygen, as shown in Figure 1. Bacteria, Thiobaci/lus ferrooxidans, are donnant at oxygen concentrations below about 3% in air (1 ppm in aqueous solution) because ofmonod kinet­ics. Hence, the maximum possible utilization is only about 75%, and it may be much less than that due to poor air sweep effi­ciency. At the maximum oxygen utilization, an ore containing two percent pyrite requires nearly 100 cubic meters of air per tonne (4,000 cubic feet per ton). The stoichiometric air require­ment to oxidize arsenopyrite is similar to that of pyrite. While the leaching solution percolating through the heap introduces some dissolved oxygen, the amount is insignificant because of the low solubility of oxygen in water, 7 to 8 ppm at atmospheric saturation. There are only three ways to provide oxygen to the heap: either air flow by natural convection, diffusion of oxygen from the surface (through stagnant air in the air-filled void space in the heap), or forced air ventilation of the heap. Each of these processes will be reviewed.

Jan 1, 1996

By Liming Yuan, James Rowland, Lihong Zhou, RICK THOMAS, DAVOOD BAHRAMI

Continuous monitoring of carbon monoxide and other fire-related parameters by means of an atmospheric monitoring system (AMS) has been used by the mining industry for early fire detection in underground mines. The National Institute for Occupational Safety and Health (NIOSH) initiated a project to integrate real-time AMS sensor data with NIOSH’s mine fire simulation program, MFIRE 3.0, to simulate and predict the spread of smoke that would provide assistance to mine fire emergency response personnel. Determining the heat release rate of a fire using the monitored sensor data was a critical component of the successful completion of this project. NIOSH researchers developed a direct method to calculate the heat release rate when a fire is within close range of sensors. However, this method is only applicable to the case where a fire occurs in AMS-monitored airways. This paper presents an improved method for determining the fire heat release rate for complicated scenarios where a fire is distant from sensors and airflow splits and merges are present. The method was validated using a fullscale diesel fuel fire test conducted in the Safety Research Coal Mine at the Pittsburgh Mining Research Division and can help mine operators and safety personnel make informed decisions during a fire emergency.

Jul 31, 2020

By Mohammed Laraba, Rodrigo Alvarez Garcia, Juan Maria Menendez-Aguado, Roula Abdelmalek

The aim of this research is the study of the WHIMS parameters on the improving process of a local (DD: Djebel Debbagh, East of Algeria) kaolin. The obtained results of performed XRF, SEM, and XRD characterization showed that this local material is an alumino-silicate containing kaolinite and halloysite with MnO and Fe2O3 impurities (respectively 39.30% and 34.67% alumina and 38.18% and 39.70% silica in both samples (DD2 and DD3). After homogenization, crushing, and milling, a multiparameters factorial experimentation (grain sizes, intensity, and dimension of matrix balls) showed that WHIMS is an effective process to improve the quality of this kaolin, mainly: removing their impurities. Dimensions of matrix balls (Db) = 2 cm, intensity of the applied magnetic field (I) = 1.5 T, and grain sizes (Dp) = > 100 < 250 μm) are the optimal values to reach 91.06% for manganese and 93.45% for iron as removing yield. The statistical analysis of these results sorted the investigation parameters and showed that Db has the highest and most significant influence on the recovery of iron and manganese particles. The magnetic field intensity (I) has a less important influence while the grain size has an average influence (positive on the iron recovery but a negative one on the recovery of manganese).

Jun 11, 2022

By William C. Cassun

The important role of pit slope design in the overall economics of open-pit mining ventures has long been recognized and well documented.1 2 Any economic analysis of a pit slope design must reflect the trade-off between the benefits and the increased risk of slope failure inherent in steeper slope angles. The conventional practice in pit slope design is based on the factor of safety analysis.&apos; The approach uses average values to arrive at a deterministic solution to slope stability. Past analyses based on this approach generally have had several drawbacks: 1. The risk from slope failure could not be quantified. 2. Only relatively simple pit wall geometries were considered. 3. The analyses were performed solely for the benefits of steeper slopes, seldom discussing the potential costs of slope failures. 4. Analyses were seldom considered in a year-by-year mine planning context. Recognizing that average values do not reflect the uncertainty in geomechanical parameters, a probabilistic philosophy to slope design has evolved. 4,5 However, this approach had not been fully developed to include complex slope geometries and mine planning consideration. In order to develop an integrated, pit slope design procedure, a research project was initiated at the University of Arizona during 1973 in conjunction with the Canada Center for Mineral and Energy Teleology. This research resulted in the development of a probabilistic design procedure. The remainder of this paper gives an overview of the probabilistic design procedure and a discussion of the requirements for the benefit-cost analysis of a pit slope design. Finally, the results of a case study undertaken at an operating mine are given.

Jan 1, 1977

By E. O. Jacobs

A coupled solid and rock fracture mechanics model is used to analyze the blast driven fracture propagation phase, predict propagation rates, and directly measure shockwave and particle velocity. The study incorporates quasi-static pre-stress conditions for different depths below the surface. The scaled experiments include dynamic material properties and quasi-dynamic fracture mechanics which are shown to significantly affect the fracture propagation. The study was performed using three-dimensional cube-type laboratory models fabricated from Polymethylmethacrylate (PMMA). The test cubes are loaded with explosives and resulting fracture networks are studied. The dynamic evaluation of the spatial crack system is monitored using a high speed image camera. An experimental model set-up is designed to indicate the pre-stress effect on deep borehole blasting and is shown that the pre-stress conditions have a decisive influence on fracture profiles and orientation. It is found that shockwaves rapidly exceed the slower dynamic fractures and a majority of cracks occur due to detonation pressure. Experimental testing using different parameters validate that explosive fracturing can predict the outcome of fracture and crack propagation in any rock type with known material properties. This can be accomplished under great stress conditions deep below ground surface. The experimental study results can be applied to a variety of industries such as mining and quarrying, tunneling, oil and gas, and construction.

Feb 23, 2014

By J. Sharp, R. Arnold, P. Rusin, T. Young, N. A. Sinclair

Many oxide silver and molybdenum deposits remain undeveloped because chemical extraction yields poor recoveries or is environmentally unacceptable. Bioreductive leaching of such ore samples at MBX resulted in high extractions of silver and molybdenum. When baseline, three-day, cyanide bottle-roll tests were conducted on manganiferous-oxide silver ore, 13.7% of the silver was extracted. In contrast, 86% of the silver was microbially solubilized into the organic growth medium by bioreduction with 99.8% dissolution of manganese. A followup cyanide bottle-roll test yielded an additional 8.5 % silver dissolution, for a total extraction of 94.5%. Baseline, three-day, acid bottle-roll tests of the iron-oxide molybdenum ore Yielded 1.8% molybdenum. However, bioreduction solubilized 93.3% of the molybdenum into the growth medium. An additional 0.3% molybdenum was solubilized during the followup acid bottle-roll test. Microbial treatment of refractory oxide ores with bioreductive bacteria resulted in higher extractions of silver and molybdenum than conventional chemical leaching. The bioleaching process occurred at a near-neutral pH at ambient temperatures. The bacterial solubilization of silver and molybdenum was achieved without the use of cyanide or sulfuric acid.

Jan 1, 1993

By Jon Y. Kaneshiro, Donald W. Scapuzzi

The primary purpose of the Prototype Installation Facility (PIF) for the Superconducting Super Collider (SSC) in this conceptual design was to test the magnets and other physics equipment. PIF was located in the northwest quadrant of the SSC 54 mile (87 km) main ring and consists of the first segment of tunnels, approximately 17,060 lineal feet (5.2 km) of 12 foot inner-diameter (ID) (3.7 m) tunnel, three 250 ± foot (60 m) deep shafts, connecting tunnels, and associated niches and alcoves. PIF would be the first portion of the main ring collider tunnel to be constructed. The geology, underground excavation conditions, underground facilities, and contractual considerations are discussed.

Jan 1, 1991

By Horry Parker Jr, Jason Gillespie, Justin Kolster, Stephen O’Connell

Construction of the 5,932-ft Reedy River Basin Sewer Tunnel in Greenville, SC was marked by a critical transition from drill-and-blast mining in mixed-face conditions to TBM excavation with limited rock coverage. In this paper, we discuss the geological, geotechnical, and risk management considerations for transitioning to TBM operations in variably weathered gneissic bedrock. After construction of an unexpected 230-ft starter tunnel due to differing site conditions, the 11-ft diameter TBM was successfully launched in December 2019 without significant ground support issues. This project highlights the effectiveness of extensive rock probing to fully characterize bedrock topography prior to the TBM launch.

Jun 13, 2021

By I. J. Lin

The effect of various types of structural modification on the critical micelle concentrations (CMC) and hydrophile lipophile balances (HLB) of certain surfactants has been considered. Using the concept of effective chain length for the substituted species, an index of hydrophobicity (I) has been defined. It is hoped that such an index will allow one to choose surfactants for particular purposes in a less arbitrary fashion than heretofore.

Jan 1, 1973

By K. O. Groves

Although chlorine oxidation has been found to be effective in destroying the CN ion, an excess of chlorine is needed to drive the reaction to completion. This often results in the formation of residual chloramines, which are toxic to aquatic life and often regulated by various states. The interhalogen, bromine chloride (BrCl), has been found to be just as effective but without the formation of persistent, residual chloramines. The hydrolysis and subsequent disproportionation of the highly-polar BrCl molecule essentially yields a solution of hypobromous acid (HOBr) and nonoxidizing hydrochloric acid (HC1). Studies have been carried out to directly compare the mechanism of CN destruction with chlorine and bromine chloride.

Jan 1, 1982

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By D. W. Leyshon

The fluidized solids technique for the calcination of phosphate rock has been well established for over 10 years. This paper is intended to review the recent performance of many of the Dorr-Oliver FluoSolids* calciners. In addition, design features of these three compartment refrac¬tory construction reactors will be described and a comparison made with fuel requirements for single compartment calcination. Also presented will be certain, aspects of the use of the rock including a discussion of non sulfate sulfur in the rock. A system is described for producing a blended mixture of calcined and uncalcined rock.

Jan 1, 1972

By H. Rush Spedden

A process has been developed and piloted to reject copper, lead, iron, phosphorus, bismuth, antimony, elemental sulfur, and insol from molybdenite concentrate without decomposing the contained molybdenite and rhenium. The impure concentrate is first heated with concentrated sulfuric acid at 260 to 290°C for 1 hour. This bake not only oxidizes the contaminating sulfides, but also activates the concentrate for later rejection of insol by flotation. Two stages of leaching follow the sulfation step. The first is an acidified water leach which extracts the oxidized copper, iron, and phosphorous; the second leach rejects the lead, bismuth, and antimony into a warm concentrated solution of sodium chloride. Final upgrading is achieved by conventional froth flotation. The chemistry of the process as well as results obtained from its implementation in a 5,000 lb/day pilot plant are presented.

Jan 1, 1971

By R. P. King

The MODSIM mineral processing plant simulator is used to find optimal combinations of target separation specific gravities in a typical modem coal washing plant. A plant that is set up with these optimal targets can deliver up to 10% more yield at the same ash content as the same plant set up with separation targets chosen by conventional methods. MODSIM is the only simulator currently available that can simulate the liberation of pyrite and other mineral matter during open-and closed-circuit grinding operations. The simulator can therefore be used to assess the benefits of grinding operations in the flowsheet.

Jan 1, 1997

By R. J. Sweigard

Many states are considering the need to establish or modify policy relating to the disposal of coal ash. One of the primary concerns is the impact of leachate from the ash disposal sites upon groundwater and nearby bodies of surface water. A detailed site investigation was conducted at a coal ash disposal facility associated with a power generation station. The disposal site is situated alongside a major river. Monitoring wells were installed and soil samples were taken for characterization. Groundwater models were used to simulate migration of leachate from the disposal site toward the river. Such models could be used potentially to verify regulatory compliance. This paper addresses the validation and adaptability of these models to this case and their usefulness as possible tools to be used in future environmental audits.

Jan 1, 1992

By R. J. Matetic

Mining operations have long been accused of causing a disruption to local, domestic and agricultural water supplies. More recently, concern for water supplies has increased with the advent of high-extraction mining techniques, namely longwall mining. Theoretically, any water bearing zone in the overburden above a high-extraction mining operation may be affected by mining. In some cases, a confining bed may be fractured causing a loss of water to a particular zone. In other cases, increased fracture permeability may enhance the ability of an aquifer to transmit and deliver water. Unfortunately, only a limited amount of studies have been conducted that characterize hydrologic changes and also quant1fythe magnitude of mining-induced subsidence. The U.S. Bureau of Mines conducted such a study at a mine site located in Greene County, PA. A total of 8 water wells were drilled and hydrologic parameters such as specific capacity, transmissivity and well yield were determined both before and after mining. Electronic water level recorders were installed on each water well to provide continuous observations of water level fluctuations.

Jan 1, 1990

By P. W. Conrad, C. Todd, N. West, R. Kramer

"Surface subsidence caused by both underground room-and-pillar mining operations and solution mining operations have each been studied separately, but never combined. In 2008, FMC Minerals began using solution mining at its Westvaco Mine as a secondary extraction method in an area that had been previously mined using the room-and-pillar mining method. Mining regulations require that subsidence associated with underground mining activities be monitored and measured annually. Researchers at Montana Tech were able to develop a relationship between measured surface mine subsidence and solution mining that can be used at the Westvaco Mine to estimate the production of trona from solution mining operations. PROJECT BACKGROUND FMC Minerals (FMC) has increased the production of trona from its Westvaco Mine near Green River, Wyoming, using solution mining as a secondary extraction method in an area previously mined using the room-and-pillar method. The area of interest was mined until 2001 with the use of a borer miner at a depth of approximately 1,600 feet. Currently, FMC determines the amount of trona produced using its solution mining operations by measuring the dissolved solids pumped from the mine. This approach, however, does not account for the location from which the trona was removed. The location from which the trona was removed and the size of the cavern created by the solution mining operations is important to FMC’s mine planning. FMC believed that with proper investigation of the subsidence at the Westvaco test site, a correlation might be found that would allow for the use of surface subsidence measurements to estimate the amount and location of trona production from the solution mining activities. The primary goal of this project, conducted by Montana Tech, was to find a relationship between the measured subsidence and the solution mining activities. The project attempted to model the relationship between the measured subsidence and the solution cavern using Salt_Subsid, an existing subsidence software package from the Solution Mining Research Institute (SMRI), to determine the program’s usefulness for locating and developing the cavern created by solution mining activities. The project also attempted to develop an equation that could be used to predict solution trona production based on measured subsidence. The data used in this study were collected over a seven year period, 2008 through 2014."

Jan 1, 2016

By R. Mensah-Biney

The kinetics of gold-bromide loading onto activated carbon has been investigated in a batch stirred reactor. The amount of gold adsorbed by the carbon was correlated with time based on a second-order equation. The rate constant for gold-bromide species onto activated carbon ranged from 0.27 to 1.2 x 10-3 (kg/t)-l(min)-l from a solution containing 25 ppm of Au, with 0.8 g carbon per liter of solution at 30° C. The equilibrium saturation capacity (Q.) was 36±3.0 kg/t from the same system. The rate of loading increased with decreasing particle size, decreasing pH, increasing temperature, and decreasing concentration of gold in solution. The calculated activation energy E. was 8.8 kcal/mole, significantly higher than those reported for physical adsorption. The equilibrium saturation capacity (Q.) increased with increasing concentration of gold in solution, but was independent of other variables such as temperature, agitation speed, particle size and pH. These rate constants and equilibrium saturation capacity for the gold-bromide species are higher than those reported for the gold-cyanide systems.

Jan 1, 1996