Search Documents

By W. B. Greer

The performance of seals in boreholes, shafts, and tunnels is an important concern in mine safety, in the control of effluents from operating and abandoned mines, and in the underground containment of hazardous wastes (Einarson and Abel, 1990; Mining Waste Study, 1988). Despite the clear need for effective seals, few documented test results are available concerning the performance of in-situ seals. Some evidence indicates that horizontal or near-horizontal holes are especially difficult to seal properly (Kelsall and others, 1982). This research involved the installation, extensive hydraulic testing, removal, and post-test examination of a l0-cm-long by 10-cm-diameter cement grout seal in a near-horizontal borehole in limestone. The work was performed in an underground mine on Marble peak in the Santa Catalina Mountains, Arizona. A test hole was diamond cored in the re-crystallized limestone of the Escabrosa formation. The hole is 33.24 m long, 10 cm in diameter, and dips at 10.4 degrees. The hole extends between two drifts and thus is accessible from both ends.

Jan 1, 1992

Semiautogenous (SAG) ball mills are being increasingly used today for the coarse grinding of a range of ores, including gold, copper and iron. Larger mines are demanding mills with larger throughputs. This has led to some remarkable developments in mill diameters and installed powers. Conventional design principles - mills with trunnion bearings - have reached their limitations. This article describes one SAG mill with a slide-shoe arrangement and Krupp Polysius' Combiflex twin drive. In August 1997, the world's largest SAG mill with a slide-shoe arrangement was commissioned in Queensland, Australia, operating as a wet mill. The inside diameter is 10.4 x 5.1 m (34 x 17 ft) effective grinding length. The 1.36-ktlh (1,500-stph) SAG mill is driven by two Combiflex drives (twin drives with 2 x 5,500-MW or 7,375-hp installed motor power) in conjunction with a girth gear (outside diameter 11,890 mm or 468 in.). Commissioning of the SAG mill was completed with no notable technical difficulties. The plant runs continuously except for planned maintenance stoppages and process-specific reasons. As this article is written, the machine has been in operation for about 8,000 hours without major problems.

Jan 1, 1998

By Irving Hoch

INTRODUCTION The demand for tunnelling can be related to urban population size and density; often, tunnelling occurs when a certain city size and density threshold is reached, and increases thereafter as a function of those population characteristics. Subways for rail mass transit are the most notable example, of course, but tunnels for water supply and perhaps for sewerage can also be related to size and density. As cities grow large they sometimes outgrow their local water supply and have to import water from distant places via tunnels; witness New York City, Los Angeles and San Francisco. And it has been suggested that Chicago use deep tunnels for storm water storage because tertiary treatment to meet water quality standards will require treating storm water runoff.(1) Other uses of underground space also increase with urban density, e.g., underground parking, concourses and shopping centers such as Rockefeller Center in New York City and the Place Ville-Marie in Montreal. These examples can be viewed as illustrative of the central point of urban land economics. As the number of people locating in a place increase, they bid up land values and make the more intensive use of land economic, with land defined to embrace the space both above and below the surface. Hence, we are led to think about the city, and of urban land use, in three dimensions. Now, if we accept the relation of underground space use to urban size and density, recent demographic trends seem anything but hopeful for future tunnelling demand: urban density is declining, population growth is slowing down generally, and there

Jan 1, 1974

By R. R. Hall

Tests were conducted to assess the potential of column flotation for beneficiation of a talc ore from Montana. This ere contained approximately 80% talc, with the gangue comprised mainly of chlorite, silica, and dolomite. A tributylamine, MIBC, and sodium silicate reagent suite proved effective for talc flotation. Rougher-cleaner column flotation in a continuous open-circuit produced a final talc concentrate which contained 0.90% Al2O3. 0.17% CaO, and 1.28% Fe2O3. These analyses represented impurity rejections of 77, 85, and 65%, respectively. Weight recovery for this open-circuit was 52%; however, weight recovery was estimated to be 75% with cleaner tailings recycle. Results from this investigation show that column flotation is a viable means for beneficiating talc.

Jan 1, 1990

By W. Jacobi, B. Haider, D. Regulla, J. Huber

[Introductory Remarks] Thermoluminescence (TL) detectors are widely used for the dosimetry of X- and[ y]-rays. Also filter devices for radon daughter monitoring have been developed in which the a activity on the filter was measured with TL-detectors (Breslin et al., 1977). For this purpose normal LiF-tablets with a thickness of 0.4 - 1 mm were used. However the lower detection limit of such TLmonitors for radon daughters is relative high, especially in areas with a high [y]-background, due to the low [a /-y]-sensitivity ratio of such thick LiF-detectors. This [a/y]-sensitivity ratio can be increased if TL-detectors are used whose thickness is comparable with the range of [a]-particles. On the basis of this consideration we have developed a simple light weighted and sensitive TL-monitor for the measurement of the cumulative radon daughter exposure in air. [Description of the "Monitor] The monitor consists of two parts: The sampling pump with the accumulator, and the sampling probe which contains the air filter and TL-detector system. Both parts are connected with a plastic tube. For operation in mines a light weight, portable air sampler with a built-in accumulator (DuPont model 125 and 200, 400 g) is used which enables an adjustable, constant flow rate in the range of 7.5 -12 1/h. These air samplers allow a sampling period of 10 hours before recharging is necessary. For radon daughter measurements in houses this pump is replaced by a larger, netoperated pump with a flow rate of 180 1/h. Figure 1 shows a schematic cross section through the sampling probe whose weight is 40 g. The radon daughters are collected on a hydrophob membrane filter (Sartorius) with an effective filter diameter of 11 mm and a pore diameter of 3 µm; its collection efficiency for radon daughters is [>] 95%. Above the filter the detector system is mounted. It consists of two thin Tm-activated CaSO4-TL films of 8 mm diameter on a Al-carrier foil manufactured by Matsushita Inc., Japan. The thickness of the TL-film is 6 mg/cm2, which is comparable with the range of a rays. The first detector is faced in 3.5 mm distance above the filter; in addition to the ambient y background this detector is exposed to the [a] and ß radiation from the radon daughters on the filter. Between the first and the second TL-detector is an Al-absorber of 0.5 mm thickness which shields this detector against the [a] radiation and partly also to the ß radiation from the filter. Both detectors have the same [y] shielding. After air sampling both TL-detectors are read-out with a commercial, hot-air reader (Matsushita Inc. / Japan, Model 505 A). The glow-curves are identical for [a and y] rays (Regulla et al., 1980). The integral TLsignal from both detectors is displayed in mR-units (or mR-equivalent). The difference between the response of the unshielded TL-detector above the filter and the shielded TL-detector is proportional to the time-integral of the filter activity, integrated over the sampling period. Calibration and Intercomparison Measurements] The linearity of the a response was checked with a 241Am-source for an [a] fluence on the detector surface of 5400 [a's/cm2•s] in the range of 102 -105 mR-equivalent. Within the experimental error of 15% the response function is linear. The TLD-monitor was calibrated for radon daughters in air by comparison with a calibrated integrating, monitor (WLM-meter) equipped with a Si-surface barrier detector and a direct electronic read-out; this instrument was developed by us for area monitoring some years ago (Haider et al., 1976). The results of simultaneous measurements with the TL-monitor and the electronic WLM-meter in mine areas and in indoor air of houses are shown in figure 2. On the abscissa the mean potential [a] energy concentration (in WL) during the sampling period is given which was derived from the measurements with the electronic WLM-meter. On the ordinate the corresponding response of the TLDmonitor to radon daughters (difference between both TL-detectors) is displayed, expressed in terms of mRequivalent per liter sampled air. It follows from this comparison a linear relationship over the whole range of 0.005 - 5 WL with a standard deviation of 10%. The resulting calibration factor for the TLD-monitor is 18± 2 mRequiv per WL • 1.

Jan 1, 1981

By Albert L. St. Peter

The "Old Reliable" four million pound blast in March of 1972 marked the opening, as far as is known, of serious efforts to commercialize the In Situ concept. That was a coyote shot, and it was followed by three blasts at McAlester Fuel's "Zonia" operation which were surface hole shots. As the only individual who had a principal part in all four shots, it seems to be appropriate to present experiences in the developments and evolutions of the in Situ method of ore extraction. Some of the problems will be described, along with proposals for management of such projects in the future.

Jan 1, 1976

By M. Jessop, V. O. Kofoed, R. Blanchard, A. Hughes

Willowstick has successfully employed a new Seismic Acoustic Resonance (SAR) method to improve seepage characterization through, beneath, and around dams. SAR is a passive seismic method that detects zones of higher permeability in the foundation and fill materials of a dam. Just as the ocean has tides, the earth’s crust experiences daily “Earth Tides” and is constantly in motion. Continual motion produces resonance signals that can be measured, interpreted, and modeled to identify zones of higher permeability within a dam and its foundation. The SAR results are analyzed in conjunction with the traditional Willowstick Method to better characterize seepage flow paths and patterns trough, beneath, or around a dam in three dimensions. When both methodologies, which use entirely different scientific principles, identify the same anomalous feature, a higher degree of confidence is gained in the results of the investigation. Willowstick has effectively utilized the SAR method on many successful dam seepage investigations. The two geophysical techniques when used in parallel have yielded complimentary results, with both methods providing beneficial information about seepage locations. This paper will detail seepage flow paths identified using both Willowstick and SAR methods for two case study tailings dams in Canada and the United States.

Feb 1, 2023

By V. Miller

C. Hertzler The difference of means of milling characteristics by rock and ore type is tested in a statistical manner in the paper. The null hypothesis being tested is that the sample means of two different populations are equal. It is assumed that the null hypothesis is true when performing the test. Because of this, acceptance of this hypothesis leads to the conclusion that the sample means of the two different populations are equal (or there is no significant difference between the sample means), not that the samples come from the same population, as the author asserts. Rejection of the null hypothesis leads to the conclusion that the sample means of the two different populations are not equal. A P value for this test is reported in Table 2 and is incorrectly identified as the probability that the two samples came from different populations. Actually, what was recorded was 100(1 - p) where p is the usual p-value. The usual p-value measures, on a scale of zero to one, the extent to which the data agree with the null hypothesis. It is the probability of observing a value of the test statistic (Z score) that is at least as contradictory to the null hypothesis as the one computed from the sample data (McClave and Dietrich II, 1982). The author makes no mention of the fact that were these tests to be conducted together, the chances of determining that the null hypothesis is not true when it is really true are increased considerably (Snedecor and Cochran, 1980). This is a multiple comparisons problem and should be dealt with accordingly. The usual methods involve adjusting the level of the individual tests. Table 2 reports an incorrect 100(1 - p) value in the comparison of concentrate grades for other rock types with .30 to .69 % Cu vs other rock types with .70 + % Cu; 86 % should be 98.6 %. Although the article can be criticized for poor data presentation and discussion of that data, the point the author makes regarding the use of these statistics in the ore reserve estimation process is well taken. It does not appear that inaccuracies in the statistical interpretations have hindered that usefulness. References McClave, J.T., and Dietrich, II, F.H., 1982, "Statistics," Dellen Publishing Co., San Francisco and Santa Clara, CA, 766 p. Snedecor, G.W., and Cochran, W.G., 1980, "Statistical Methods," The Iowa State University Press, Ames, IA, 561 p. Reply by V. Miller After reading Ms. Hertzler's comments, it appears that the differences noted were basically semantics. If the paper is ever presented at a math symposium, some changes will be needed. When deciding the best way to present the data to mining engineers and geologists, I decided that presenting the probability that the two sample groupings came from different populations (reverse to the Null hypothesis) was easier and would require less verbage to explain. Hence, the 100(1 - p) difference which was noted. Ideally, I would have preferred to give the recovery and concentrate grades, then comment which ones had significant differences. Unfortunately, Kennecott Corp. did not grant permission to publish the ore body's actual recoveries and concentrate grades. The conclusion is that there was, as expected, a relationship between the ore's geologic properties and the metallurgical properties, and by determining this relationship, the overall mineral model was greatly improved.

Jan 8, 1984

By D. D. Harbuck

The U.S. Bureau of Mines investigated germanium and gallium extraction from an ore containing 0.089% Ge and 0.036% Ga. While previous researchers concluded that a reducing agent such as 502 is needed to extract germanium and gallium from such ore, this research showed that high extractions (87% Ge, 97% Ga) were possible using sulfuric acid alone, if the acid concentration were properly controlled. This control was achieved using a two-stage counter-current leach circuit. Microprobe analyses revealed that the non-extracted germanium is in solid solution with quartz, and therefore cannot be leached with 502 or sulfuric acid.

Jan 1, 1991

By S. K. Kawatra

It has been observed in some mineral processing plants that grinding circuit efficiency varies seasonally, such as in some plants which are located in the northern U. S. and Canada and undergo large seasonal temperature changes, with the grinding circuit efficiency different between summer and winter. This indicates that the temperature of grinding circuit slurry has a noticeable effect on grinding performance. The effect has rarely been studied. To this end, an investigation to examine the effects of changing temperature on efficiency and determination of the mechanism responsible has been carried out. Plant investigations and laboratory experiments have been conducted in order to study hydrocyclones. It was demonstrated that under otherwise constant operating conditions, the d50(c), size decreased linearly with increasing temperature, while the shape of the reduced efficiency curve remained constant. This effect was determined to be due to changes in slurry viscosity with temperature.

Jan 1, 1988

By T. Negeri, A. O. Orumwense

Microwave pretreatment is one of the emerging technologies which have been reported as having potential economic benefits for the processing of amenable ores. The application of microwave pretreatment to the processing of refractory and finely disseminated ores is of great interest as the technology can potentially reduce high comminution costs and improve mineral liberation. Sized ore samples were subjected to microwave irradiation at power levels varying from 1 to 5 kW over exposure times of between 1 and 6minutes in order to determine the influence of heating rate on mineral transformation, ground product size distribution and mineral liberation. The microwave irradiated samples were ground and subsequently floated. A comparison is made with non-microwave treated samples. Flotation grade and recovery show a strong dependence on the microwave absorption characteristics of the mineral components of the ore, in the following decreasing order -sphalerite, galena, and lastly chalcopyrite.

Jan 1, 2003

By Y. J. Wang

Stall or aerodynamic stall of axial-flow fans has long been recognized as an important operational problem in mine ventilation. To develop a technique for characterizing fan stall in multiple-fan ventilation networks, a research project was initiated through the Generic Mineral Technology Center for Mine Systems Design and Ground Control. Considering that fan stall is related to multiple operating points, this paper discusses a numerical model for multiple-fan ventilation networks, design of the experimental setup for two-and three-fan ventilation networks, and numerical methods for solving multiple networks solutions. It is hoped that the results of this project will lead to an innovative method of ventilation network analysis and simulation, thus preventing stall.

Jan 1, 1991

By K. R. Gardner, P. B. Altringer, R. H. Lien

The Bureau of Mines, U. S. Department of the Interior, is investigating biological and chemical reduction of selenate and selenite from waste waters. A mixed bacterial culture, isolated from agricultural waters, removed selenium from four oxidized cyanide solutions from precious metals operations containing 0.6 to 30 ppm Se and 13 ppm CN. Up to 85% selenium removal was attained using bacteria under controlled batch conditions in a 3-L stirred tank reactor and in small-scale continuous tests conducted in a rotating biological contactor (RBC). Fe(OH), reduction of the selenium reduced the effluent concentration to 0.02 ppm Se; however, the reagent costs were prohibitive. A final processing scheme may involve a combination of biological and chemical treatments.

Jan 1, 1991

By Thomas M. Turner

Open pit mining, always a demanding task, faces two relatively new problems today: 1. Availability of equipment. Moderate to large draglines can take as long as 6 years from date of contract to date of operation. 2. Environmental restrictions. Strip mining in the minds of environmentalists compares unfavorably on the scale of social desirability to the activities of Jack the Ripper and Attila the Hun. Specifically, lowering of the water table to allow strip mining in the dry is being looked upon with increasing disfavor. The modern dredge offers relief in both problem areas. Delivery on a major dredge might run 18-24 months rather than 60; and lowering of the water table is precluded, thus minimizing environmental objections. In addition, a lower first cost and potentially increased efficiency may offer real advantages to the miner who is forced away from his traditional mining methods. This talk is dedicated to acquainting the miner with dredge types, advantages, and limitations.

Jan 1, 1975

By William Harrison, Robert H. Trent

GENERAL DESCRIPTION History The most striking feature of mining in the United States has been the infrequent use of longwall systems. This system, which accounts for the majority of coal production in Europe, Japan, and other countries, is only recently growing out of its infancy in the mining of normal coal seams and is still untried in the mining of thick coal seams in the US. Its use in the mining of metal and nonmetal ore bodies has been virtually ig¬nored, except for isolated instances in trona, copper, and uranium. Longwall mining is believed to have originated in Shropshire, England, towards the end of the 17th cen¬tury (Laird, 1973). Although the method used would be considered primitive by today's standards, many of the basic concepts have remained unchanged. Longwall mining of coal in the US was first introduced before the turn of the century, but it never gained acceptance as it did in Europe. Historically, longwalling was a cyclic method where a single cut of coal was removed from the face on the producing shift each day, and the work of building stone packs in the gob and manually moving roof support was completed on the off shifts. Due to the amount of dead work, productivity was extremely low. In Europe, however, longwall methods were required despite the high costs involved, because only by this method could coal under heavy depth be mined with any reasonable degree of recovery. Reserves of coal lying under shallow cover, and therefore minable by room¬and-pillar methods, were long ago inadequate to supply most of Europe's coal requirements. In the US coal min¬ing has historically proceeded laterally with the new mines in virgin areas to replace old mines; in Great Britain, Germany, Japan, and many other countries, mining must proceed downward to greater depths. The depth of cover for most coal operations in the US is shallow, i.e., 61 to 305 m (200 to 1000 ft). This, combined with large reserves, has made room-and-pillar methods almost universally applicable. However, longwall systems were tried around the turn of the century. Whenever used, it was frequently noted that the opera¬tion was under the direction of men with foreign ex¬perience and was tried under ideal conditions. Some of the mines that were using longwall or had tried longwall prior to 1910 were the Radiant mine, CO; Vinton Coal Co., PA; Cambria Steel Co., Johnstown, PA; Grundy County and Spring Valley, IL; and unnamed mines in Washington, West Virginia, Kentucky, Iowa, and Kansas. As late as 1961, there was one circular longwall in operation at Centerville, IA. The first modern-day op¬eration to take advantage of European technology and longwall methods was Kaiser Steel Corp. at its Sunnyside mine near Price, UT. Due to deep cover and extremely poor roof conditions, combined with a need for in¬creased production, Kaiser management decided a new method was required and turned to longwall in 1961. The first longwall consisted of an Anderson Mavor shearer loader, British Jeffrey-Diamond conveying equip¬ment, and Dowty roof supports with a capacity made up of two and three 27-t (30-st) capacity props. After nor¬mal start-up problems, this unit averaged over 454 t (500 st) per shift (White and Palacios, 1976). During and after World War II, technology in hy¬draulics and controls had advanced to the point that self-advancing supports and hydraulic props were being developed. In 1960 only I % of West German produc¬tion was from mechanized longwall faces. This in¬creased to 37% in 1970 and 63% in 1973 (Kohlgruber, 1974). In 1976 there were 246 coal mines operating in the United Kingdom. Although this is only 50% of those operating ten years ago, the production has increased 42%, mainly through improvements in longwall equipment and methods (Hunter, 1976). In France and other European countries, the devel¬opment of longwall mechanization has been similar in seams up to 2.44 m (8 ft) thick. In seams that exceed 9.14 m (30 ft), a variety of longwall caving has been developed for coal seams with dips of 0 to 1.6 rad (0 to 90°). Those with the greatest success will be discussed later. As noted, the development of longwall mining to its present state of the art has mainly taken place since World War II with substantial gains in the last ten years. Mechanized longwall has been the result of several re¬lated major innovations (Jackson, 1975) 1) Development of the flexible armored face con¬veyor which can be installed along the face and moved forward without disassembly. 2) Development of face machines such as single and double drum shearer and coal plows which operate in conjunction with the armored conveyors. 3) Development of self-advancing hydraulic roof supports which now include chocks, chock shields, and shields. 4) Reliance of caving of the immediate roof based on proper planning and development. 5) Use of pneumatic slowing to enable extraction below overbuilt areas. The most recent developments in the mining of coal by longwall in the US include the introduction of shield supports at Kaiser's York Canyon mine in New Mexico, single-entry longwall development at Kaiser's Sunnyside mine, and Mid-Continent's advancing longwall system in Colorado. Metal and nonmetal longwall systems in the US have included the mining of copper at White Pine, MI; uranium in Utah and New Mexico, and trona in Wyoming.

Jan 1, 1982

By J. W. Francis

The paper about to be presented deals with the relatively straightforward problem of mining two seams of coal separated by an interval. This may seem to be a simple problem but within a twenty-mile radius of Consolidation Coal Company's Burning Star # 4 Mine at least seven (7) different techniques of two-seam mining have either been tried or are now in use. This great variety of techniques should point out that there is no single simple solution; a conclusion often reached when dealing with mining problems. As a background for the techniques presently in use at the Burning Star # 4 Mine, we will briefly outline the other five (5) stripping techniques used in the area: 1. Captain Hine 6360 Range Diagram (Figure 1) 2. Leahy Mine Range Diagram (Figure 2) 3. Burning Star # 3 Mine 5860 Range Diagram (Figure 3) 4. Burning Star # 3 and # 4 Mines Dragline in Pit Range Diagram (Figure 4) 5. Captain Hine 2570/5561 Range Diagram (Figure 5) Each of these techniques was chosen because it provided the best and least expensive alternative for mining the coal under the particular restraints encountered. The Mine Engineers at our Burning Star # 4 Mine, Mr. Dennis Mahan and Mr. William Weaver, will now detail two additional mining techniques, out-lining our experience to date.

Jan 1, 1977

By P. Somasundaran

Three major types of solution chemical equilibria involving flotagents (Le. flotation reagents such as collectors, frothers and modifiers), minerals and solution play a crucial role in determining the behavior of complex flotation systems. Minerals of phosphates (apatite and francolite), tungsten (wolframite and scheelite) and associated carbonates (calcite and dolomite) are sparingly soluble in aqueous solution and form dissolved mineral species in bulk solution. Such dissolved species interact with mineral solids, often resulting in surface conversion of the minerals. In addition, they can interact with various flotagents and lead to surface or bulk precipitation and loss of selectivity in the flotation. Relevant solution equilibria of such sparingly soluble minerals and their interactions with oleic acid and structurally modified reagents were determined in this study using a multi-pronged experimental approach. Methods to manipulate and control the solution chemical equilibria and thus achieve selectivity in flotation systems are discussed.

Jan 1, 1990

By Fred C. Bond

Any improvement in the accuracy of commercial comminution calculations under the Third Theory must be accomplished either by increased precision in energy input measurements, or by a better evaluation of the total new crack length produced, as indicated by the feed and product size distributions. Since at the present time feed and product sizes are approximated solely by the microns 80% passes, the most promising opportunity for increased accuracy lies in consideration of their plotted size distribution characteristics. This paper shows how more accuracy can be obtained over an increased range of feed and product sizes from size distribution studies.

Jan 1, 1962

By Nagashi Ogushi

Geochemical prospecting method using stream sediments, soils and rock chips has been tested to see the applicability for the typical Kuroko field in Japan. Three independent anomalies have been detected in maps being shown by grav densities of cells which are represented by the results of factor analysis as well as distribution of minor elements scaled in logarithm. A small vein type mineralization which has outcrops could be attributed to the origin of them whereas the one near the surface of known Kuroko deposit to a coincidence. The addition of drill core geochemistry is required to complete the interpretation.

Jan 1, 1982

By Betty L. Gibbs

Before the first shovelful of dirt is removed from a developing mining property, a wide range of data must be collected, organized and analyzed. Among the key steps in this process are: • Visualization of the deposit from drill hole data and geologic interpretation, using all available information, including surface geology, geochemistry and geophysics. • Drawing of vertical and horizontal sections. • Construction of a 3D solid model of the deposit. • Contouring of deposit outlines and geological structure until the model represents best estimate of reality. • Estimation of grade and quality distribution. • Calculation of reserves. • Examination of possible mining methods. • Determination of economic feasibility. Many techniques are available to aid in this process of mine project feasibility analysis, from quick pencil calculations to sophisticated computer methods. However, time races faster in the complex modem business world than it did 50 years ago. Tried and true pencil methods take too much time. Opportunity may pass a mine developer by while a property is still in the first stages of analysis. In the days of hand techniques, initial analysis of the economic feasibility of a mining project usually stopped with reserve calculations and broad mine planning. Further planning was not done or was done only for the short term. Manual techniques require too much time and manpower to evaluate a longterm mining program. Mining-industry recognition of computer utility has increased. Most companies now use computers in technical applications and could not conceive of working without them. Building initial computer models of a deposit may take nearly as long as hand techniques. But the payback comes when changes are needed and a variety of mine plans are quickly tested.

Jan 1, 1990