Search Documents

By T. M. Gurr

Large quantities of phosphate rock are mined and processed in Central Florida (Figure 1). The phosphate rock from the mines is further processed in "chemical plants" to produce phosphoric acid (Figure 2). A by-product of the processing' of the phosphate rock to produce fertilizer chemicals is an impure form of gypsum referred to as phosphogypsum. For each ton of phosphate rock processed, approximately 1.5 tons of phosphogypsum is produced (Figure 3). The typical method to dispose of this by-product gypsum is to stack it in large piles, locally referred to as gypsum stacks or gypsum fields (Figure 4). These gypsum stacks have been the focus of many studies in recent years in an attempt to identify the potential for ground water and/or air pollution associated with the stacks. This paper attempts to discuss some of the ground water impacts and current attempts to minimize these impacts.

Jan 1, 1990

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States,2 and in addition, feldspar is produced as a by-product by firms whose major products are spodumene and mica.3 Feldspar is concentrated by hand-cobbing and flotation; the latter forms the major method of separating and concentrating feldspar. Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan and the USSR. According to the U. S. Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 tons and 2,514,000 tons respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel,-tile and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, North Carolina have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water

Jan 1, 1976

By Brent A. Elliott, J. Richard Kyle

This article reviews the production trends of industrial minerals since 2000 for Texas, the leading U.S. producing state of industrial minerals with a total value of $5.2 billion in 2017, equivalent to 6.9 percent of all U.S. minerals value. Most current Texas industrial-mineral value comes from the production of cement, crushed stone, industrial sand, and construction sand and gravel. Construction material consumption is concentrated in the 25 metropolitan areas of the state, with production of industrial minerals in nearby counties. With Texas’ population projected to reach 50 million by 2050, continuing in-state development and production of industrial minerals will be required to meet in-state and regional demand. Texas’ most rapidly growing production of industrial minerals is industrial sand to supply proppants for multiple unconventional petroleum plays. Texas’ favorable geology and economic factors provide opportunities for the identification and development of new industrial-mineral production sites. Repurposing of former industrial-mineral production sites for post-production development likely will increase as efficient land use evolves. Understanding the geologic, economic and societal framework of industrial-mineral resources will facilitate more informed decisions about the complex issues that the region will face, including effects of sea-level rise on coastal infrastructure.

By R. D. Begley, A. W. Khair

This paper presents an assessment of modeling techniques in predicting subsidence over longwall areas. Extensive instrumentation has been made, both at the surface and subsurface, at three longwall mines in northern West Virginia. Ground movements were monitored during a three- year period until subsidence ceased in these areas. A comparative analysis of empirical subsidence prediction techniques including graphical (NCB), profile function, influence functions (USBM, Bals', Knothe's, and zone area) will he presented. A brief geologic and topographic description of each site, along with the instrumentation and monitoring program, will also he presented.

Jan 1, 1990

By J. J. McClellenand, R. A. Jankowski

Face ventilation and water sprays are the primary controls used on continuous miner sections to protect workers from respirable coal and silica (quartz) dust. Laboratory tests were conducted by the U.S. Bureau of Mines to determine the impact on respirable dust concentrations when increasing airflow from 3000 to 9000 cfm (1.42 to 4.25 m3/sec), water flow from 15 to 35 gpm (0.057 to 0.132 m3/min) , and water pressure from 80 to 200 psi (5.52 x105 to 1.38 x106 pa). The effective limits for each control and interactions between these controls were of particular interest. Initial analysis concentrated on defining the impact of the control parameters on the respirable fraction of the feed dust, which was a blend containing 90% coal and 10% quartz. Gravimetric sampling indicated that airflow had the most significant individual impact on respirable dust levels and resulted in reductions of 99% at the operator and 57% in the return. Regression modeling was used to predict dust concentrations at the operator and in the return. Significant interactions were observed between control parameters and often, defined the level for a control parameter where increases above that level did not significantly benefit dust control. Increasing airflow to 8400 cfm (3.96 m3/sec), water flow to 25 gpm (0.095 m3/min), and water pressure to 140 psi (9.65 x105 Pa) typically provided respirable dust reductions at both sampling locations, while optimizing use of control resources. After determining these relationships for the total respirable fraction, selected filters were analyzed for quartz content to define the impact on the quartz component of the feed dust. For the individual control parameters, airflow again had the most significant impact and resulted in reductions of 98% at the operator and 26% in the return. Regression modeling of the quartz concentrations indicated that no significant interactions between control parameters were present. At the operators location, airflow was the only parameter identified as having a statistically significant reduction for quartz dust. A reduction in quartz approaching 95% was observed for increasing airflow to 6000 cfm (2.83 m3/sec). Increases above 6000 cfm had little additional impact. In the return, a linear relationship between control parameters and quartz levels was observed with reductions of approximately 27% predicted for increasing any one control parameter to its maximum level. The synergistic impact of increasing all control parameters to maximum levels resulted in a maximum predicted reduction of 81%.

Jan 1, 1991

By M. Sears, G. S. Esterhuizen, Z. Khademian

According to the 2010-2019 Mine Safety and Health Administration (MSHA) accident report database, 91% of reported ground control accidents in U.S. longwall mines were caused by roof instability. Gateroads are subject to significant changes in loading conditions from the development to the longwall abutment loading phases. When combined with thinly bedded shale roof, found in many U.S. longwall coal mines, the design of efficient roof support becomes challenging. In previous work, the Bonded Block Method (BBM) modeling of roof by UDEC was validated against field extensometer measurements in a longwall gateroad entry roof at a 180-m depth of cover. The BBM was shown as capable of capturing delamination and buckling of shale roof, one of the main roof instability mechanisms in longwall mines. This paper presents the recent findings on the roof-support interaction using BBM models of the same longwall entry. The effects of cable bolts, roof bolt density, and strap support on potential roof instability are studied. These types of studies are difficult and costly to conduct in an operating mine. Results show how the contribution of bolts, straps, and cable bolts can be quantified using the BBM models. The study demonstrates the potential for BBM numerical models to help understand the complex roof and support system interactions and to assist with optimizing gateroad support systems.

Feb 1, 2023

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By J. K. Wolski

This paper addresses the effects of using jet fans as booster fans in mine ventilation networks. A method was developed to determine the pressure generated by jet fans using the momentum theory. The influence of a reduction cone and other ventilation parameters on the jet fan pressure was analyzed. Verification experiments conducted in the Waldo Mine are described. Examples are given to demonstrate the conditions for the effective use of jet fans.

Jan 1, 1998

By William E. Wallace, Larry Grayson, Thomas Simonyi, Joel C. Harrison

Application of an SEM-based methodology suggests a reason for past contradictory results on the relationship between quartz and coal workers' pneumoconiosis (CWP). Results indicate that coal seams with the same bulk analysis of quartz have different amounts of surface-available quartz. Our research shows that the amounts of pure and surface-available quartz in a respirable dust vary directly with the rank of a coal seam, except in the case where rock materials are mined. The estimated amount of surface- available quartz therefore provides a measure of the quartz-related fibrogenic potential of a respirable dust.

Jan 1, 1992

By Jack G. Pippenger

The Coteau Properties Co.'s Freedom mine is a surface operation near Beulah, ND that produces more than 13.6 Mt/a (15 million stpy) of lignite. Coteau, a subsidiary of North American Coal Corp., ranks among the largest mines in North America. In 1994, Coteau ranked eighth in annual coal sales, becoming the largest mine outside the Powder River Basin of northeastern Wyoming. However, for the Freedom mine to stand alongside the Powder River Basin heavyweights, Coteau had to overcome several obstacles. These included a coal seam with three-quarters the heating value and overburden-to-coal ratios three times higher than Powder River Basin mines. Coteau's ability to compete has been built around a program of continuous improvements in productivity, cost efficiency and innovation.

Jan 1, 1995

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. An alternative parameter, the organic efficiency, does indirectly consider process economics, but it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach, the partition moment of inertia, is introduced. This parameter reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure that promises better use of performance data. IntroductionPartition curves are commonly used in the characterization, evaluation and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, density separators and other beneficiation technologies that are based on intensive physical properties. Graphically, the partition curve depicts the recovery of particles as a function of the physical property on which the separation is based, such as particle density, size or magnetic susceptibility. Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic S shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout, or bypass, values; the midpoint slope; and the separation cut point, defined as the property value with 50 percent recovery.Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, as a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point, that is, an infinitely large slope. One common formulation of this slope, the Ecart Probable, Ep, is derived by evaluating the slope between the 25 and 75 percent recovery points:"

Jan 1, 2016

By W. S. Versluis, G. W. R. Kuzyk

Atomic Energy of Canada, Ltd. (AECL) is constructing an Underground Research Laboratory (URL), a major component of-the Canadian Nuclear Fuel Waste Management Program. In July 1988. AECL and the US Department of Energy commenced a cooperative research program that included extending the URL shaft by 190 m (623 ft) to the 443-m (1,453 ft) depth. The shaft extension, 4.6-m- diam (15-ft-diam), was excavated by full-face blasting using a burn cut. A Galloway stage accommodated the research activities and the sinking contractor's requirements. Blast designs incorporated controlled blasting techniques to minimize blast-induced damage on the shaft walls. The full-face method has been very effective, with 3.5-m (11.5-ft) rounds being advanced.

Jan 1, 1990

By John S. Newton

Modern high capacity underground mining machinery is a complex of mechanical, electrical and hydraulic components which have greatly increased capability over similar components of mining machinery of ten and. even five years ago. Looking into the future I feel certain in stating that there will be changes equally great in the coming five and ten year periods. With this premise in mind, I should like to bring to your attention some of the things that do and will have a continued major impact on the industry, particularly as they relate to the maintenance and operation of these machines of increasing capability. In underground mining today, nearly every individual plays a key role. A machine operator's importance in his work is comparable with that of the pilot of an airplane, a railroad engineman, a bus driver, a skilled machinist, a bulldozer operator and many others whose assignment is one of doing, by himself, with his hands and his brains all that the specially designed machine has been created to do. These machine operators are supported by a staff of skilled engineers, maintenance personnel, supervision, etc., but objectives are realized only when the operator maintains his schedule. What is being done and what can be done to make it easier for the operator to maintain his schedule which, as with the airplane, is constantly being improved? This question can be answered best, perhaps, by dividing the subject into four general categories - (A) Power Supply. (B) Control and Protective Devices. (C) Hydraulic Component Design. (D) Mechanical Design.

Jan 1, 1962

By E. Bloomstein

The Lone Tree gold mine is located about 4S kilometers east from Winnemucca on the west flank of Lone Tree Hill in Humboldt County, Nevada. The deposit occurs at the north end of the low, rolling Havallah Hills and is about 1 kilometer south of Interstate Highway 80, in sections 11 and 14, Township 34 North, Range 42 East, Mount Diablo Base and Meridian (Fig. 1). The Lone Tree deposit is outside of any previously established mining district and all lands are owned or controlled by Santa Fe Pacific Gold or affiliated companies.

Jan 1, 1993

By Nathaniel Arbiter

The increasing size of flotation cells as the use of flotation has increased is traced from the first United States application of the process in Montana in 1911 through the following eight decades, using data from the Taggart handbooks (1927) and (1945), from the SME Handbook (1984), and from recent manufacturers' catalogues and other sources for the 1980s and 1990s. With the earliest mechanical cells less than 1 m3 (359) in volume and the largest now available at 200 m3 (7,000ft3), three requirements are necessary: 1) demonstration of advantages in replacing smaller volume by larger volume cells; 2) estimating power requirements, impeller dimensions, and operating rpm by correlation equations; 3) considering effects of using larger cells, in necessarily much shorter rows, on process kinetics. The resulting seven tables that address these problems are presented, and their implications discussed.

Jan 1, 1999

By Kwadwo O. Adutwum, George M. Potter, Todd J. Harvey

Ashanti Goldfields Company (AGC) is the largest gold mining company in Western Africa. Their jewel operation is a highly inte­grated set of mines and plants situated in Obuasi, in the Ashanti region of Ghana. This operation is responsible for mining 5.5 mil­lion tonnes of ore at 4.6 git annually from a series of open pits and underground mines. The sulphide ore is highly refractory with untreated gold recoveries in the range of 30-40%. The milling facilities are quite varied and include an oxide treatment plant (OTP), a heap leach, a sulphide roaster circuit (PTP), a tailings treahnent plant (TIP) and the most recent, a sulphide treatment plant (STP). The sulphide treatment plant, the world's largest stirred tank biooxidation circuit, was commissioned in early 1994. This plant treats approximately 800 tonnes of refractory gold con­centrate per day with overall recoveries of75-85o/o(ll, Biooxidation was selected for its ease of operation and less exotic maintenance requirements as well as its ability to achieve comparable gold recoveries. Unfortunately, despite stirred tank biooxidation being one of the lower cost methods of treating refractory ores, it is still too costly for low grade refractory materials. GeoBiotics, Inc. has developed a proprietary technology that allows the economic treatment of lower grade refractory gold ores through heap biooxidation. AGC has a significant resource of low grade refractory sulphide ore. This ore is too low grade to warrant BIOX™ sulphide treatment and its oxide plant recov­ery is low at 35-45%. GeoBiotics and AGC have completed pre­liminary testing and economic analysis of heap biooxidation for this material. Additionally, the feasibility of producing a gravity concentrate from the tailings of the sulphide treatment plant has been explored. This concentrate would be coated onto the low grade sulphide and biooxidized concurrently. Gold recoveries for the biooxidized low grade sulphide have increased to 75% and the gravity recovery from the STP tailings has achieved 80% uti­lizing a Falcon concentrator. The preliminary economics of the proposed full scale plant are very favourable with a pre-tax IRR of 233% and a payback period of 6 months. This paper details the biooxidation testing, flow sheet devel­opment and preliminary economics of employing heap biooxi­dation for low grade refractory ore treatment at Ashanti Goldfields' Obuasi operation.

Jan 1, 1998

By A. Ramage

Since late 2010, CH2M HILL has been working with a confidential client who holds a long-term commitment to sustainable development (SD). The commitment is aligned with all three elements of the triple bottom line: people and society, ecosystems and environment, and financial and economic systems. These commitments are carried forward by the firm?s executives, managers, and operational sites, and are evident in materials posted on the company?s public website. These materials include a formal sustainability report prepared in accordance with the Global Reporting Initiative (GRI) guidelines (GRI, 2006), a report that outlines key SD challenges and progress toward the GRI targets, and a delineation of risks and opportunities outlined in the firm?s Form 10-K and Annual Report. In keeping with its commitments to SD targets, our client wished to consider SD issues in its decision processes for facility expansion or new projects. The company engaged CH2M HILL to meet this goal, based on working relationships established through existing contracts and CH2M HILL?s leading capabilities in sustainable solutions.

Jan 1, 2012

By J. L. Post

A large body of readily available Na-montmorillonite is present about 24km (15 miles) east of Fallon, Nevada. The clay is comparable to Wyoming Na-bentonite, but with somewhat less MgO and somewhat more Fe2O3 in its crystal structure. The physical and industrial properties of the Nevada clay are comparable to those of the Wyoming clay. The Na-montmorillonite is presently mined for use as hazardous waste barrier material and as a sealant for canals. It may be economically feasible to process the clay material for removal of impurities.

Jan 1, 1996

By K. J. Shoop

An analysis of an iron ore processing plant showed that its performance was affected by seasonal temperature variations, resulting in reduced grinding efficiency in the winter months. Laboratory and pilot plant studies were conducted to determine the cause of the observed loss of efficiency at lower temperatures. Experiments were divided into two groups: 1) Drop testing, which was performed to determine the effect of brittleness and frozen pore water on the breakage characteristics of the ore. 2) Wet grinding, which was further divided into laboratory tumble tests and pilot plant scale tests. Laboratory tumble tests were performed to determine the effect of temperature on the grinding of iron ore. This was done by varying the percentage of fines and percentage of metamorphic clay material added to the iron ore grinding charge. The pilot plant scale tests were conducted as a scale-up of the laboratory tumble tests and to determine the effect of temperature on slurry rheology, and how this changing rheology affected the grinding of iron ore. The combined results of drop testing and wet grinding were used to make some predictions of the performance of plant scale autogenous grinding. In drop tests the breakage characteristics of the iron ore had no noticeable change in size stabilities for dry and water saturated samples over the temperature range studied (-25°C to 25°C). The effect of frozen pore water was not observed due to the low apparent porosity of the iron ore. The addition of fines to the test charge caused a decrease in the amount of new fines produced for both the laboratory tumble tests and pilot plant scale tests. The production of fines further decreased when tests were performed at the colder temperature. The increased energy consumption at lower temperatures was dominated by rheology phenomena. The addition of metamorphic clay material to the iron ore test charge resulted in more fines being produced in the laboratory tumble tests. This was due to the metamorphic clay material grinding easier than the iron ore. This caused an increase in the amount of fines in the mill, which in turn, would prematurely slow down the grinding of iron ore because of an increase in the viscosity of the slurry.

Jan 1, 1995

By E. A. Devuyst, G. Robbins

A unique process for removing cyanide and base metal complexes from industrial waste streams was patented by G.J. Borberly et al. (1984). The process uses SO2 (liquid or gas, or solutions of sulfite salts, or from burning elemental sulfur), plus air that is dispersed in the effluent using a well agitated vessel. Acid produced in the oxidation reactions is neutralized with lime at a controlled pH generally in the range 7 to 10. The reaction requires the presence of soluble copper as a catalyst which can be supplemented by copper sulfate if necessary. The process can be applied to the detoxification of gold and silver mining waste streams, such as carbon-in-pulp (CIP) tailing pulps, barren solution bleeds, pond waters and heap leach rinse solutions and also to plating shops wastewaters. The SO.jAir process has substantial advantages over two of the main alternative methods of cyanide destruction, namely alkaline chlorination and hydrogen peroxide. Alkaline chlorination is highly penalized in terms of reagent consumption. Chlorine is a strong oxidant reacting with species other than cyanide present in the effluent such as thiocyanate and sulfides. Furthermore alkaline chlorination is an incomplete detoxification process. Iron cyanide is not removed and the potential for harmful by-products species exist. Consequently final effluents may be subject to additional treatment in order to comply with regulatory demands.

Jan 1, 1991