Search Documents

By Robin J. Hickson

The Grasberg copper-gold deposit was discovered in the spring of 1988, one year before the planned closure of Freeport Indonesia's original Ertsberg openpit copper mine. In spite of Grasberg's remote location, 600 m (1968 ft) above the Ertsberg, atop a hitherto inaccessible mountain, Freeport-McMoRan brought its latest open-pit mine into production in the last week of 1989, less than two years after discovery. Freeport Indonesia's (FI) copper-gold mining operations are located in Irian Jaya, the easternmost province of Indonesia on the western side of the island of New Guinea. Fl's six ore deposits are all located within a 10- x 10-km' (3.9- x 3.9-sq mile) Contract of Work area. They are all between the elevations of 2900 and 4300 m (9515 and 14,100 ft) above sea level, some 96 km (60 miles) from the island's southern coast. A 118-km (74-mile) access route connects FT's port site of Amamapare on the Arafura Sea to the project area. The first section is an 18-km (11-mile) barge waterway. The final 100-km (63mile) is a two-lane gravel highway. The highway terminates 9 km (5.5 miles) beyond the FI townsite at the project's central mill, some 2850 m (9250 ft) above sea level. The mining areas are separated from the mill by a 780-m (2560-ft) sheer cliff face. The world's longest free span tramway system, with a total length of more than 1.6 km (1 mile), is the only means of access for men and materials between the mill and the surface mines. Weight restrictions for the tramway for equipment considered for the project are 15.4 t (17 st). The minimum clear width dimension of two tunnels along the portsite access road is 5.6 m (18.4 ft).

Jan 1, 1991

By T. M. Klemetti, T. J. Batchler, T. J. Matthews

How representative are partial-panel screen tests of the in situ response of screen to roof and rib deterioration and displacements? Can a more representative procedure that tests up to two full screen panels improve the utilization and effectiveness of screen as a roof and rib support? This paper details a new full-panel screen test procedure and the initial results. The full-panel test frame was designed to test a 2.4 by 3.6-meter screened area with bolt spacing as small as 0.3-meter increments. The initial design included up to 6 screen pull points, but additional locations can be added to produce a more uniform loading. The test frame was developed to capitalize on the capabilities of the Mine Roof Simulator (MRS) at the Pittsburgh Mining Research Division (PMRD) of the National Institute for Occupational Safety and Health (NIOSH). The initial tests included a baseline test of a partial panel (1.22 by 1.22-m screen section) using the original 1.52 by 1.52-meter test frame, a 1.22 by 1.22-meter screen section test in the new full-panel test frame, and two tests of 2.4 by 3.6-meter screened area in the full-panel test frame. The 1.22 by 1.22-meter screen section tests in the full-panel test frame produced a peak load 6% higher and a yield load 30% lower than the partial-panel (original) test frame. The multiple pull points of the full-panel frame produced variable yield, peak, and intermediate loads, but on average were lower than the single pull-point tests. INTRODUCTION Roof and rib surface support has become a major component of the stability and safety of underground coal openings in the past 15 years. The use of screen, either metal or synthetic, has proven to decrease the injuries of underground coal miners. By 2005, there were 466 injuries in the United States caused by roof skin failures, with numerous mines not employing roof screen. In contrast, in 2015 there were 175 injuries caused by roof skin failures, with at least some of the reduction due to the increased use of roof screen. A continued effort to increase the utilization of screen in areas of underground coal mines where workers are traveling and working can reduce these injuries even further. To aid in this effort, the testing of various screen types under various loading and attachment conditions is required. Past testing efforts have primarily consisted of partial-panel testing in a laboratory setting. Laboratory testing of roof screen, both metal and composite, has been conducted in several ways by researchers, manufacturers, and other entities. The primary focus on the testing has been evaluating weld integrity of 1.22 by 1.22-meter screen section tests of various screen types utilized in mining (Dolinar, 2006; Dolinar, 2009; Tannant, 2001). There have also been several efforts at numerical simulation of the screen and screen/rock interactions (Murali et al., 2006; Shan et al., 2014). A few full-panel tests were performed with one pull or loading point in the center of the screen panel (Shan et al., 2014). As most previous efforts have mentioned, the only true way to evaluate the capabilities of screen is to conduct full-panel testing. Single wire strand, weld, and partial-panel (1.22 x 1.22-m) tests as well as numerical modeling only provide insight into the actual response of full-panel screen. A new test frame and procedure have been developed at PMRD to conduct various loading, anchoring, and material testing.

Jan 1, 2019

By David Green

Outokumpu introduced Flash Flotation in the early l 980's for the recovery of floatable material from grinding circuits. The devel­opment came as a result of surveys made in the company's own concentrators, initiated to find ways of improving recoveries with increasingly complex and lower grade feeds. Hydrocyclones make a separation on the basis of particle size and mass, resulting in the "over collection" of fine grained, high S.G. particles. Minerals such as pentlandite, galena and gold are easily caught in the circulating load around the mill until they are overground and rendered more difficult to collect. In the case of downstream flotation this may simply involve a reduction in the rate coefficient due to the finer sizes or, as is commonly experienced in gold operations, the mate­rial is slimed and coated onto non-floating gangue and is eventual­ly lost to tails. At the time of Outokumpu's plant surveys, it was a relatively common practice, particularly in Pb operations, to have a flotation section fed directly from the secondaiy mill discharge. This is called unit flotation and certainly provided an improvement but very high wear rates and frequent sanding out of the cells was com­mon. The development of the SkimAir® Flash Flotation cell by Outokumpu provided a subtle but quite dramatic departure from the unit cell approach. Now it was possible to feed cyclone under­flow into a special purpose-built flotation machine and recover a final grade concentrate from the grinding circuit (see Figure I). The cell was designed to handle the coarse circulating load, per­mitting the coarsest fractions to be short-circuited back to the mill and retain the floatable sizes for a nominal time of 30 seconds to several minutes. The short retention time was possible largely due to the relatively clean content of the cyclone underflow stream. This means that the fine gangue is not present except in small quan­tities and most of the fine to mid-size paiiicles are higher S.G. and more likely represent valuable mineral. This condition provides for very high rate coefficients. Typical operations would recover 40-60% of the valuable mineral in this fashion and improvements in recovery were typically from 2-5% for sulphide minerals to the 5-20% range for gold and silver.

Jan 1, 1998

By B. Alegria

The depressing effects of different inorganic chemicals on the flotation of pyrite have been investigated in this study. The results of the flotation tests indicate that pyrite can be depressed by oxidizing as well as reducing agents under controlled conditions of pH and reagent dosage. Oxidizing reagents such as potassium chromate and potassium dichromate were found to cause complete depression of pyrite in the acidic pH range. These effects are similar to those obtained in the pyrite-cyanide system. A less stable oxidant, potassium permanganate, inhibited the flotation of pyrite at a concentration as low as 0.1 mol/L at all pH values, Addition of reducing chemicals such as ferrous chloride or manganous sulphate to the flotation of pyrite were found to produce depressing effects depending on the additive concentration and pH of the solution.

Jan 1, 1982

By Dr. Richard F. Coon, James D. Mavis

Risks and abatements associated with preliminary reconnaissance, plugging and filling, and maintenance of perched mine water pool are examined. This case history showed that the initial appeal of portal plugging was replaced by concern over potential environmental hazards when details of implementation were investigated.

Jan 1, 1992

By Francis F. Pitard

North America had an Important role in the early development of sampling theories. Unfortunately many progressive ideas were soon frozen into a series of guidelines based on the philosophy that "honest sampling only requires good judgment and practical experience". Such a philosophy appeared to be good enough In the early age of the mining Industry; however, it became quickly necessary to find new approaches. During the last thirty years, Pierre Gy's sampling theory provided tremendous breakthrough in the comprehension of this new science, nevertheless went unnoticed in North America. Sampling always generates complex problems and as the philosopher and mathematician Descartes suggested: "A complex problem can often be dissociated Into a series of several simpler problems, only then you try to solve those one by one". The only way to solve sampling problems is to consider each component of the overall sampling error: components of a continuous model such as long-range quality fluctuations, periodic quality fluctuations, weighting fluctuations; components of a discrete model such as materialization errors, delimitations errors, extraction errors, fundamental errors, grouping errors, and segregation errors. PAST AND CURRENT PRACTICES Many sampling methodologies have been developed, improved, and standardized during the first half of this century. Accordingly, sampling equipment has been proposed, selected, and used by standards committees. Today, there is a tremendous variety of sampling methodologies and corresponding tools offered to anyone with limited experience in sampling and it is very easy for a chemist, metallurgist, geologist or miner to spend considerable money in equipment transgressing the most basic rules of sampling correctness. Sampling stations that never worked properly in modern plants often cause engineers to abandon them and return to a primitive form of grab sampling.

Jan 1, 1986

By R. J. Barnes

Consider a typical blast at a surface gold mine in North America. For example, the low-grade area of Bench 4000 at AMAX Gold's Sleeper Mine (Winnemucca, Nevada). Bench 4000 is 20 feet high (=6m) , and blast holes are drilled and sampled on a 14 foot by 14 foot square grid (a4m x 4m). A representative blast includes between 50 and 150 holes, encompassing 15,000 to 45,000 tons of material (w14,000 to 41,000 metric tons).

Jan 1, 1989

By Hong Zhang, Quanming Li, Gang Li

China, a globally recognized major mining country, holds one of the largest quantities of tailings pond country in the world. The total number of mines in China has been ranked first in the world. It is a major concern for Chinese safety management to give great importance for tailings pond safety, stability and sustainable development. For the past few years, China has increased efforts to investigate and govern discrete issues of tailings and to carry out a series of special renovation and comprehensive treatment actions to improve safety management levels and to decrease the likelihood of tailings pond accidents. In the end of 2015, China successfully eliminated hazardous tailings ponds and dangerous tailings ponds. Moreover, the total number of tailings decreased from 12,273 to 8,869. However, there are still 1,425 "head-top" tailings that threaten the lower masses’ safety. This greatly signifies the Chinese tailings pond safety, stability as well as sustainable development. In turn, this may improve the Chinese tailings life cycle safety management system and help reach the goal of attaining closed-loop management in the tailings pond life cycle. Based on the summary of the tailings pond accidents in both China and other countries from 1961 to 2015, and by analyzing the types and causes of accident, this paper investigated the successful experiences and effective measurements of British Columbia (Canada) and Australia in the tailings pond life cycle safety management. This paper summed up each country’s tailings life cycle safety management requirements and analysed the characteristics and differences of tailings safety management by comparing 5 aspects: tailings life cycle safety management process, main design parameter, construction requirements, monitoring, and the tailings pond closing management. Based on these observations, this paper suggests some measurements to improve the tailings pond life cycle safety management in China, such as strengthening tailings pond safety management, improving tailings classification, increasing design parameter values, establishing mine reclamation fund, and so on.

Jan 1, 2017

By Raj K. Rajamani, Samira Rashidi

High pressure grinding rolls have been utilized in various operations during the past four decades, simply due to their inherent mode of breakage that offers metallurgical benefits with pronounced energy reduction. For every new application, wear and in particular roll surface wear protection has always been the focal point of HPGR trade-off studies. Wear remains an important issue throughout a mine’s life given inevitable variations in the ore deposits properties. Hence, the capability of continuous scanning of rolls provides ample information about any deviations in the design values as well as their effect on the wear pattern. In part I of this manuscript, we present the feasibility of in-line scanning of roll surface in a 200 × 100 mm lab-scale HPGR. First, the in-line scanning was developed in a mock-up roll and then the scanner was moved to the laboratory-scale HPGR. We present the choice of scanners and the methods adopted to achieve high-level accuracy of determining wear. Even though we planned for micron-level precision of scanning, the inherent variability in shaft rotation was higher than the variability in the roll diameter due to wear. The hundred-kilogram mass processed in the HPGR was not sufficient to create enough wear that is discernible to the in-line scanner. Yet, the method tested is a promising avenue for inline scanning of HPGR rolls.

By Juan Andres Jarufe, Carlos Cifuentes

Numerical modelling has been extensively used to estimate plastic displacement in faults and rock mass surrounding mine excavations. Particularly, for fault slip seismicity, modelled plastic displacement is usually utilized to estimate seismic potential, however these methods assume that all the displacement caused during an specific simulated excavation step, is released as a single event at each step. This representation corresponds to a conservative estimation since rock mass displacement does not occur as one single event but as an exponential distribution of many small displacements and a few large ones. When displacement is expressed as seismic magnitude, this exponential distribution is addressed as the Gutenberg Richter (GR) relationship. This paper present a method to decompose the results from numerical models into a distribution of seismic events The reconstruction of the GR relationship from modelling displacement permits not only a more realistic approximation of the expected maximum magnitudes but also provides a tool to develop a probabilistic estimation of the maximum possible magnitudes.

Apr 26, 2022

By Chinmay Shingote, Robert Visintainer, Renjie Ke, Jaikrishnan R. Kadambi, John Furlan

Hydrocyclone separators are some of the most widely used instruments in a variety of industrial applications. Their major functions are to sort, classify and separate solid particles and liquid droplets within a multiphase flow system. Research studies employing both experimental and numerical methods recognize that the performance of a cyclone is related to its geometric dimensions as well as the inner flow pattern. Although many successes have been achieved over the past years, the majority of investigations only focused on the simplified design of cyclone geometry and on single-phase flow. Therefore, this study set out to investigate the flow field in a new-design hydrocyclone and used particle image velocimetry (PIV) to explore the complex swirling flow behavior inside the cyclone within an air core. The flow field inside the cyclone was also studied by computational fluid dynamics (CFD) simulation using a commercial CFD package. Different turbulent models were tested in this study with a moderate-size mesh, and the interface of liquid phase and air phase was predicted by the volume of fluid (VOF) model.

By David B. Spencer

This paper describes a process for separating non-ferrous metals such as aluminum, copper and zinc, from other residential and industrial waste by means of permanent magnets. Although the separator may be used in the recovery of non-ferrous metals from auto scrap, most of the testing to date has been aimed at recovery of non-ferrous metals from municipal solid waste, especially recovery of aluminum from the heavy fraction of a resource recovery plant. In most resource recovery plants the incoming solid waste material is first shredded and then air classified into a light and a heavy fraction. The light fraction which contains mostly paper, cardboard, etc., can be used either as a fuel for power generation or in the production of new paper products. The heavy fraction which remains consists mostly of glass, ceramics, wood, ferrous metals and non-ferrous metals. The ferrous metals may be removed from the heavy fraction by conventional magnetic separators. After primary shredding, most of the glass and ceramic is fine in size and may be screened away leaving a residue of wood, cardboard, and non-ferrous metals. This residual heavy fraction is the input material for the separator described in the present paper.

Jan 1, 1975

By Keith Whiting

The Little Boulder Creek molybdenum deposit is in central Idaho, in the White Cloud Range about 3.2 km (2 miles) northeast of Castle Peak, the highest peak in the range. The elevation of the deposit is about 2591 m (8500 ft). The deposit is accessible only by helicopter or by a 12.9-km (8-mile) trail from the county road along the East Fork of the Salmon River. The nearest towns are Clayton [25.7 km (16 miles) northeast], Stanley [33.8 km (21 miles) northwest], and Ketchum [45 km (28 miles) south-southeast]. The principal known deposit at Little Boulder Creek is called the "North Zone." In this zone, the molybdenite occurs both in stock- work veinlets and disseminated through metamorphosed quartzite of Pennsylvanian age. Pyrite is ubiquitous, averaging perhaps 0.05%. Scheelite and/or powellite are present in trace amounts. An intrusive quartz monzonite stock, probably of Cretaceous age, bounds the deposit on the west. A steep fault which drops Tertiary age Challis volcanics into contact with the mineralization limits the deposit on the east.

Jan 1, 1991

By Turan Uysal, Thierno Saidou Barry, MURAT ERDEMOGLU, Mustafa Birinci

Nonbauxite ores such as aluminum silicate clays and coal fly ashes have been widely considered as potential resources of alumina (Al2O3). The interest focused on these ores is due to their high alumina content. Over the years, in countries where there are little or no bauxite reserves or where the recovery of existing bauxite ores to produce alumina with the Bayer process is not economical, alternative processes have been explored. Among these processes, acid leaching is seen as the most attractive process. In the acid leaching process, heat treatment for thermal activation to destruct the refractory structure of the minerals in the ores is generally recommended as a pretreatment method. Recently, the applicability of high energy ball mills, which are useful for mechanical activation as a pretreatment method before leaching, has attracted much attention. This is a short summary of our previous review [1], giving the details of alumina manufacturing from thermally and mechanically activated clays and coal fly ashes by acid leaching.

By R. H. Snow

Although industrial size reduction methods have an energy efficiency of only about 1 percent, methods of size reduction have not changed much for many years. One reason for slow progress has been the oversimple viewpoint that a single law should exist to relate size reduction to energy input. Modern simulation methods decompose the grinding process into a grinding rate function (selection function) and a breakage function. The breakage function is difficult to measure, and it usually requires tracers if it is determined from milling experiments. Prediction of breakage functions from basic principles is one objective of this paper. In this study we focus attention not on the gross energy input to the experiment, but on the spatial distribution of stress energy within the particle. We are led to this viewpoint by experimental observations of a few previous investigators (Bergstrom2, Rumpf3, Axelson4) and our own observations. Oka and Hiramatsu recently used their calculations of stress within particles for prediction of breakage, but again they tried to correlate the size of the fragments with the total stress energy, rather than the approach we propose. We assume that the stress energy is stored in the interior of the particle as the load is increased, until the particle breaks. We assume that each element of the particle breaks into fragments of a mean size that depends on the locally-stored stress energy. The size distribution of fragments is the computed from maps of the stress-

Jan 1, 1972

By L. B. Hales

December 3, 1972, James Wm. White presented the results of an instrumentation and process control survey which was sponsored by the Anaconda Company at the annual Tucson Subsection AIME meeting.(1) Twenty-six responses were obtained from questionnaires sent to 48 operating plants throughout the world. The survey results were discouraging in that there were more failures and problems than examples of success. The following quotes are taken from the text of the paper. "We run our mill by the seat of our pants." 'If these blue sky Ph.D.'s (in the instruments and controls area within research) had some operating experience they wouldn't make a lot of the suggestions they do."

Jan 1, 1981

By Dan Urich

This paper covers the construction and operation of the Grate-Kiln system at the Humboldt Mine. The mine concentrator and pellet plant are located approximately 14 miles West of Ishpeming, Michigan, on the Marquette iron Range. Production of pellets began in mid-July, 1960.

Jan 1, 1962

By H. A. DeMirjian

Oil production rate and ultimate primary recovery from a heavy or viscous oil reservoir is usually limited to a very small fraction of the original oil in place. Typically, normal production rate is in the range of up to 10 barrels per day and expected ultimate cumulative production is up to 10% of in place values. Heavy oil reserves are not all alike. The physical properties of the rock, the liquid hydrocarbons, and depths of the deposits are so different that each reservoir poses a unique enhanced oil recovery problem. In some reservoirs thermal recovery by internal heat generation or external heat injection has been successfully exploited. In other reservoirs, mining the oil bearing formation for oil recovery by surface processing has been practiced. This paper will present an overview of the heavy oil recovery state of the art and discuss the critical factors leading to the decision for selection of a conventional hydrocarbon recovery or mining and extraction processes.

Jan 1, 1978

By Travis S. Wellman, Jon C. Volkwein

The Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low profile mining machine. Tests were conducted in a full scale model mine using a Joy 12 CM 10-AA continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters included: mining position, depth of cut, brattice setback and combinations of scrubber, directional sprays or symmetrical sprays. Results indicated that either directional or symmetrical water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 6 m (20-ft) blowing curtain without sprays. No FVE values were less than the standard 6 m (20-ft) blowing results.

Jan 1, 1989

By Richard A. Thomas, Liming Yuan, Wei Tang, JOHN SOLES

Lithium-ion battery applications are increasing for battery-powered vehicles because of their high energy density and expected long cycle life. With the development of battery-powered vehicles, fire and explosion hazards associated with lithium-ion batteries are a safety issue that needs to be addressed. Lithium-ion batteries can go through a thermal runaway under different abuse conditions including thermal abuse, mechanical abuse, and electrical abuse, leading to a fire or explosion. The NIOSH Mining program is conducting research to prevent and respond to lithium-ion battery fires for battery electric vehicles in the mining industry. In this study, experiments were conducted to investigate the effectiveness of different suppression systems including dry chemical, class D powder, and water mist for lithium iron phosphate battery pack fires. The effects of activation time and release time of the water mist system on the suppression of lithium-ion battery fires were studied. The results of this study may be helpful for developing strategic firefighting and response plans for battery-powered vehicles used in mining.

Feb 17, 2024