Search Documents

By S. Castro, L. Gutierrez

A classification of flotation processes carried out in concentrated electrolyte solutions, e.g., seawater, is proposed using the most obvious features of these processes: low or high content of Mg2+ and Ca2+ ions, pulp ionic strength, and pH. The first distinguishable group is the processes carried out in NaCl/KCl solutions, about 0.5 M in the case of salt flotation of inherently hydrophobic minerals, and at concentrations about 10 times higher in the flotation of potash ores. In the flotation of sulfide ores, such as nickel or copper ores, with xanthate-like collectors, the xanthate collector is apparently not affected by pulp ionic strength and only adjustment of frother may be required. Content of Mg2+ and Ca2+ ions in seawater is the main difference between such systems and fresh water. The presence of these metallic ions can adversely affect flotation in the pH ranges over which these ions hydrolyse. The successful flotation of Cu-Mo ores typically requires depression of pyrite at high pH values achieved with the use of lime. However, in seawater, flotation of Cu-Mo ores requires removal of the hydrolysis products of the Mg2+ and Ca2+ ions or the use of a pyrite depressant that can be effective over the pH ranges that are much below the pH of hydrolysis. Mg2+ and Ca2+ ions also affect flotation of phosphate ores with fatty acids. In this case, the depression mechanism is not caused by precipitating magnesium hydroxides on the mineral surface but by precipitation of collector insoluble salts, and the same ions are responsible for depression in both cases. In the seawater flotation of Cu-Mo sulfide ores and phosphate ores, the practical solution involves either removal of Mg2+ and Ca2+ ions prior to the flotation or complexation with other reagents.

By Aurel Goodwin

Remarks of Aurel Goodwin, Chief, Division of Health, Metal and Nonmetal Mine Safety and Health, Mine Safety and fEealth Administration, U. S. Department of Labor, before the Society of Mining Engineers of the AIME, Littleton, Colorado, on October 18, 1979. I appreciate this opportunity to speak before the Society of Mining Engineers of the AIME. The topic of my presentation is the Mine Safety and Health Administrations's (MSHA) concern and obligations with regard to asbestiform minerals. Asbestiform minerals - the magical group of hydrated, silicate minerals which possess a fiber like structure capable of being woven, like and into cloth. Their unique combination of properties, such as resistance to heat and chemical attack, high tensile strength, and flexibility was recognized centuries before Christ. Pausanias, the early Greek geographer, speaks of golden lamps made about 430 B.C. with incombustible wicks of "Carpathian flax." The Romans used asbestos as cremation clothes to conserve the ashes of deceased persons of rank. Charlemagne had an asbestos table cloth that he used to pass through fire to clean (1). Early recognition of the health hazards associated with exposure to asbestos was documented in the first century by Pliny the Elder, a Roman naturalist, and Strabo, a Greek geographer. Bath wrote of slaves with sickness of the lungs, whose occupation was that of weaving asbestos into cloth. This concern for the health of asbestos workers disappeared over the ages.

Jan 1, 1979

By J. Kou

In this paper the activation behavior of quartz using Ca(OH)2 as an activator in quartz reverse flotation with anionic collector was evaluated and their adsorption behavior was investigated using a variety of techniques. The adsorption of the collector KS-I on the surface of quartz with and without Ca2+ was primarily characterized using Quartz Crystal Microbalance with Dissipation technique (QCM-D), which is a high sensitivity in-situ surface characterization technique. The flotation performance was evaluated using a laboratory mechanical flotation cell at different process parameters such as pH, collector dosage, and Ca(OH)2 dosage. The anionic collector evaluated was a commercial fatty acid KS-I. The QCM-D data showed that the collector adsorbed on quartz more readily with Ca2+ as activator. The mass and structural property of the collector layer adsorbed on quartz surface at 2.16×10-3 mol/L of Ca2+, 0.3 g/L of collector and pH 12.0 have been studied using the technique of QCM-D. The chemisorption of the collector KS-I on the surface of quartz in presence of Ca2+ were also demonstrated by means of zeta potential, QCM-D and FTIR analysis.

Feb 23, 2014

By James Giulianelli

Personnel at the Jet Propulsion Laboratory (JPL) are studying the technology and applications of salt-gradient solar ponds (see below) for both electrical and thermal energy generation. The brine extraction and processing site operated by the Kerr-McGee Corporation at Searles Lake, California, offers ideal conditions for economic construction of solar ponds. Furthermore, since rising conventional energy costs adversely affect the economic recovery of brine by the present process, this site was selected for a study on the feasibility of integrating the solution mining of trona (Na2CO3?NaHCO3?2H20) in the lower salt with solar ponds for heating. The major emphasis of this study was to determine whether inexpensive thermal energy available at the brine extraction site would be useful in extracting increased mineral value from the resource. The present operation, which involves the simple extraction of the complex brine and its processing at the adjacent plant, is sometimes referred to as solution mining. Since the concept discussed in this paper involves injecting a heated sodium sulfate brine to dissolve carbonate underground, the proposed scheme is referred to as "enhanced" solution mining. The subject is discussed in greater detail in a recent JPL report. (1)

Jan 1, 1981

By James F. Archibald, Ferri Hassani, Jacques Nantel, David O. DeGagné

Operators depend upon the success of backfilling programs to ensure that mine activities run continuously (Archibald et al, 1993) where backfilling is an integral part of the mining cycle. In order to ensure that the backfill is prepared and delivered to the stope possessing the required engineering properties, as designed, and that the backfilling process is safe, mine operators at all stages of the backfilling system must be adequately trained for their tasks and be aware of how their work affects other backfilling stages, both up- and down-stream of their station. Mine operator training is primarily based on learning on-the-job from experienced supervisors or training personnel. Classroom training and the availability of reference manuals are less common. While in use by many industries for some time now, computer-based training (CBT) is becoming more readily accepted by the mining industry for a wide variety of training. It is not intended to replace on-the-job training, but to augment it. CBT offers many advantages to enhance operator learning by utilizing multimedia presentations, interactions and on-line testing to teach complex concepts and relationships. Discussions with many operations revealed that there is an industry need for a backfill guide for frontline operator training and as a reference manual for operators and mine engineers. Sponsored by the mining industry and the CIM, "Mine Backfill, An Operator's Guide" has been developed by the Departments of Mining Engineering at Queen's University and McGill University to fulfil this need. "Mine Backfill, An Operator's Guide" is an interactive multimedia package that incorporates high quality colour images, animations, sound, and video with text to review the main backfill methods employed in Canada, including hydraulic/slurry, paste and rock fill. The Guide is divided into training and reference primer sections. When in training mode, the operator is guided through a presentation of common mining and backfill practices and technologies so that he/she may become more familiar with different aspects of backfill processes. To ensure that key concepts have been learned during training, the operator will be tested after each section using a series of multiple choice and true/false questions. When in reference mode, alternatively, the operator may browse through the information in a more detailed and independent fashion through a series of interactive menus. The Guide focuses on the following main topics: resources, surface preparation, distribution, stope activities, health and safety, and quality control. Special features included in the Operator's Guide are a Buyer's Guide, a Trouble Shooting Guide, and an interactive glossary of backfill and mining terms. Concepts in interactive and computer-based learning are also reviewed in this paper.

Jan 1, 2001

By Alex Lowson, Dan Tempelis

The Riverside Badlands Tunnel segment of the Metropolitan Water District of Southern California’s Inland Feeder Project, was lined with a segmented concrete primary lining and a welded steel final lining with the annulus filled with Low-Density Cellular Concrete (really a grout). The paper describes a numerical modeling technique that was developed to determine safe grout placement procedures to avoid pipe flotation, and shows the relationship between flotation and the rheology of the liquid grout. Design details of the steel liners are often not well suited to grout placement, and recommendations are given on how to improve this.

Jan 1, 2003

By X. F. Wang, K. B. Fu

"We investigated experimentally and theoretically the adhesion behavior of Acidithiobacillus ferrooxidans (At.f6) to different copper sulfides. The adsorption experiment showed cell densities of 10.74 × 106, 8.06 × 106, 3 × 106, 4.24 × 106 and 2.35 × 106 cells/cm2, respectively, on the surfaces of djurleite, bornite, covellite and chalcopyrite. The order was: djurleite > bornite > covellite > chalcopyrite. The results indicate that A. ferrooxidans has high affinity to adhering to the surfaces of djurleite and bornite in the acidic region. But the thermodynamic approach predicts that there will be no attachment of At.f6 to the surfaces of bornite, covellite and chalcopyrite. This discrepancy is due to the inadequate description of electrostatic interactions. The DLVO approach shows attachment of At.f6 to the surfaces of djurleite, bornite and covellite, and repulsion between At.f6 and chalcopyrite. The DLVO approach can explain the differences of the adhesion of At.f6 to different copper sulfides.IntroductionThe bioleaching of low-grade copper sulfides is a developing technology, and has been applied successfully to the extraction of copper from secondary sulfide minerals (Watling, 2006; Pradhan et al., 2008; Akcil and Deveci, 2010). The bioleaching of chalcopyrite is still a major challenge (Bosecker, 1997; Brierley and Brierley, 2001; Ehrlich, 2004). A study conducted at Billiton Process Research showed the following preferential order of sulfide minerals leached by mesophilic cultures: chalcocite > bornite > cubanite > covellite > pyrite > enargite > carrolite >> chalcopyrite (Dew et al., 1999). The bacteria can solubilize the valuable metals from the orebodies by the oxidation of minerals. Bacterial adhesion plays a critical role in the bioleaching processes (Chen et al., 2008; Harneit et al., 2006). Generally, bacterial adhesion can be explained by surface thermodynamics and the extended DLVO theory, in which the adhesion energy between the bacteria and mineral is calculated as a function of the separation distance (Sharma, 1999; Bos et al., 1999; Sharma and Hanumantha Rao, 2002). These methods take into account Lifshitz-van der Waals interactions, electrostatic interactions and acid-base interactions (Busscher et al., 2010). These interactions are very well understood and formulated in mathematical equations. The most important inputs in these calculations are surface energy, surface charge, electron donation and electron acceptance on the bacterial cell surface and mineral."

Jan 1, 2015

By E. D. Sehnke

The refractory materials industry provides the largest commercial market for nonmetallurgical grade bauxite. Refractory grade bauxite is prepared from bauxites having low iron, titania, and alkali content by calcining at temperatures near 1,650° C. Although there are substantial bauxite reserves in the world, premium grade bauxite ores suitable for use in refractory applications are limited to only a few specific sources, primarily in Guyana and the People's Republic of China. Consumption of bauxite for refractory use is closely associated with the production and consumption of primary metals, in particular iron and steel. Barring major disruptions within the principal producer nations, sufficient supplies of refractory bauxite will be available to meet world demand well into the next century, and raw material costs will continue to determine the availability of markets for bauxite-based refractory products.

Jan 1, 1992

By S. Kenzap, V. Kazakidis

Risk assessment is an essential component of mine feasibility studies. However, it is often challenging to identify the appropriate analysis and derive the required input data. The uniqueness of a mining project and the associated technical issues require customization of the risk assessment approach to meet both requirements and characteristics. The uncertainty driving the operating risk in mine feasibility studies and its assessment through Monte Carlo simulation as a component of a cash flow analysis are discussed in this paper. The paper introduces the use of the analytic hierarchy process for derivation of qualitative input and conducts quantification of the three main sources of operating performance delays, equipment, ground and schedule problems, in a cash flow simulation. A methodology for the assessment of operating risk in mine feasibility studies is presented.

Jan 1, 2011

By Firat Atalay

Estimating the spatial distribution of ore grade is one of the most critical steps to proceed with an investment decision on a deposit. Kriging is the most widely used method to estimate the ore grade, but alternative techniques are being developed. Machine learning algorithms can be used as alternative methods to classical kriging. In this paper, the iron (Fe) grade of a deposit is estimated with the XGBoost algorithm, and the results are compared with kriging estimation results. For the estimations, samples collected from drillholes were used. Due to the different natures of the estimation methods, different steps were taken to perform the estimations. The results show that XGBoost produced higher-range estimates, which is a desired result in ore grade estimation, and the minimum and maximum of the estimates were lower and higher than the kriging estimates, respectively. However, like kriging, the estimation results were smoother than composites, and the variance of the XGBoost estimates was lower than the variance of composites. This means that even though estimation with XGBoost mitigates the smoothing effect, the estimation results suffer from smoothing like kriging.

Dec 1, 2024

By A. K. Sinha

Ever since electricity was introduced, electrical injuries and electrocutions have continued to occur regularly in coal mines. An analysis of the two hundred cases of electrocutions which occurred during 1956 to 1970 indicated that over 50 percent of the incidents were caused by the ineffectiveness or lack of electrical grounding. Research shows that various types of arbitrarily designed ground beds are in use and that the ground resistance and current are often very high and subject to wide seasonal variations. The results of a recent research are discussed in this paper.

Jan 1, 1980

By E. J. Onuscheck

With passage of the Federal coal' Mine Health and Safety Act of 1969, many challenges have been directed to the industry's mining and safety engineers. The most critical challenge is that of ventilation. The language concerning ventilation in many sections of the Act could very well deprive or limit the mining engineer in planning the ventilation for new mines, since the Act requires federal approval of all ventilation plans. Dependent upon approval and of course application of the law, this could, due to economics, prohibit the opening of new mines in some cases. Petitions for modification of some mandatory standards relating to ventilation have already been filed under Section 301(c). It is quite possible that many of these standards may be modified.

Jan 1, 1970

By William Tattersall

On behalf of my agency, the Mine Safety and Health Administration, I would like to add my appreciation that all of you could be here today. Previous dust symposia over the years have proved the value of close cooperation among universities, government agencies, and professional societies in advancing knowledge of dust research and development in the interest of miners and the industry. I'll just comment briefly on MSHA's part of the overall effort by all parties to control miners' exposure to respirable coal dust and other airborne dusts. As you know, our agency's congressional mandate is to do what is necessary to assure that miners will have safe and healthful workplaces. In the area of coal mine health, this has meant joining with the mining community in a continuous campaign to keep respirable dust and quartz levels below applicable standards to prevent or reduce disabling coal workers' pneumoconiosis and silicosis arising from excessive exposure to respirable quartz. Currently, our agency is processing about 120,000 coal dust samples taken by MSHA and company people during the year and about 8,000 samples taken from metal and nonmetal mining operations. Our dust program, like other MSHA programs, has benefited from increased computerization of records. The attack on CWP has had the highest priority of government and industry. The goal has been to sharply reduce social costs of suffering victims and their families as well as the associated future payments under the black lung benefits program. During the 1989 fiscal year, about 104,000 former miners received about one and a half billion dollars in benefits. Since the program began, nearly 25 billion dollars have been paid out. Much progress has been made in lowering dust levels in coal mines since the standard of two milligrams per meter of air was established in 1972. Before that time, there was a 4-to-10-percent probability of a miner developing coal workers' pneumoconiosis at typical pre-1972 exposure levels. However, under the maximum respirable dust levels allowed today, this probability has been reduced to about 1 percent. Since average dust levels are lower today, we can expect fewer miners to develop CWP in the future. Out goal continues to be elimination of both coal workers' pneumoconiosis and silicosis in both coal and nonmetal mining. In 1985, MSHA revised its coal mine quartz policy to allow mine operators to submit dust samples used in setting the quartz standard. Previously, only single MSHA samples were used. Even though less than half of the mine operators have taken advantage of this change, it has provided a larger population of samples for analysis then before. Also the policy allows operations that are on a reduced quartz standard to have the standard reviewed every six months. In underground coal mining, the job of roof bolter typically has higher than normal exposures to quartz. About 45 percent of respirable dust samples from roof bolting operations contain more than 5 percent quartz and therefore are put on a reduced quartz standard. One objective of the policy revision was to improve miners' health by follow-up monitoring, and this is being done with roof bolting jobs. MSHA studies of surface coal mining operations have provided data showing that bulldozer operators and highwall rotary drill operators often have high exposure to quartz dust, and our agency is directing enforcement efforts to reducing this hazard. One of the most important responsibilities of MSHA's metal and nonmetal mine health division is the respirable dust sampling program. In the last few years, nearly 3 out of 10 samples have

Jan 1, 1991

By C. V. Deutsch, J. B. Boisvert, J. L. Deutsch

Data used to build geostatistical models come from a wide variety of sources with potentially differing sample errors and volume supports. Typically all available sample measurements are pooled together for statistical analysis irrespective of the quality of the data. The sample data is used to assess spatial continuity, make local estimates and assess uncertainty. A new methodology is proposed to simplify accounting for samples of differing quality. The result is improved estimates with higher weights assigned to high-quality samples, while low-quality samples receive less influence in resource estimation. A new dimension, d, is introduced and calibrated to account for sample error and/or volume during estimation. The addition of an extra dimension can be easily incorporated in existing kriging or inverse distance workflows. The only additional parameters required are the sample error and volume for each datum. The methodology is demonstrated and the improvement in local accuracy is documented. Extending the dimensionality of the domain to four (three spatial dimensions and the additional d dimension) requires a valid 4D variogram model; therefore, the spherical variogram model is generalized to arbitrary n-dimensions.

Jan 1, 2011

By L. Adler

A systematic, balanced and inclusive formulation of the vast input data for mine design is presented. Since the quality of this statement severely influences subsquent design it is extremely important to senior mining engineers and the profession-at-large. If unfocussed, chaos can result along with serious ommisions. The basic categories, each a traditional one are: 1) Natural Conditions (geology and geography), 2) Company Capabilities (monetary and managerial), 3) Public Domain (regulations, contracts, good will, etc.) and 4) State of Art (mining engineering professionalism). To further reduce the data additional organizing principles were used: the distinctions of mining (vs. civil) engineering, proceeding from the general to particular, the basic engineering dimensions, and separating dependent from independent variables. The results are a unique and unified corpus, which anticipates the mine design procedure.

Jan 1, 1987

By K. W. Harris, K. A. Perry

Underground coal mines beneath Black Mountain in the Harlan County district of the Central Appalachian coalfields have an extensive history of bump events, which yields an elevated probability for significant injury or fatality to underground miners. According to Mark (2009), Harlan County has had the greatest concentration of deep-cover retreat mining in the United States. Combined with the extensive multiple seam mining history, room-and-pillar coal bumps have had a disproportionate impact on coal operations in this region. The Harlan seam, one of the principal, economically recoverable coalbeds exploited beneath Black Mountain, has a significant burst history that extends into modern times. A numerical investigation using the LaModel software of 17 bumps that occurred at the same mine in the Harlan seam was conducted and used to create a calibration methodology which serves as the quantitative basis for current and future numerical efforts in an adjacent mine exploiting the same reserve. In addition to this numerical study, a qualitative assessment of the geologic factors that are believed to contribute to the bump potential was completed. Combined with stability prediction using the numerical basis, these geologic factors will be used for recognition of high bump potential areas with the goal of reducing the potential for future bumps, helping to ensure the highest level of safety and productivity for underground personnel.

Jan 1, 2016

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By G. Barbery

In Mineral Processing, the objective of most processes is the separation of mixtures of minerals, which are originally associated in composite particles. Feed preparation processes grinding for instance, which take place before beneficiation or separation processes do not usually break particles at the boundary between mineral phases. They produce composite ("middlings") as well as liberated particle. It is therefore necessary, in a particulate system, to determine the proportion of particles which are liberated as well as, ideally, the size distribution of minerals which remain associated in composite particles. Up to now, there has been a lack of experimental techniques to characterize completely composite particulate systems. Heavy liquid separation which is commonly used to obtain information of this type can only be applied to simple binary cases for which one mineral has a low density (lower than e.g 2.8 ). The technique which is proposed in this paper involves the measurement of parameters on polished sections of particles mounted in a matrix, and the use of mathematical transformations to reconstruct in three-dimensions the information obtained from these measurements .

Jan 1, 1977

By William C. Ellis

Underground water is part of a continuing hydrologic cycle, which involves all elements of water occurrence. All groundwater of economic importance is in process of movement through a porous rock stratum from a place of intake or recharge to a place of disposal. Groundwater moves and is contained in fractures in the rock and/or in intergranular spaces of porous formations. Where there have been no water developments by man, groundwater is in a state of approximate equilibrium and the forces of replenishment and discharge are in balance. Thus, groundwater, unlike other mineral resources, is constantly being replenished in most areas at a rate which is measurable and which is important in the planning of its utilization. As illustrated by Figure 1, replenishment of groundwater supplies results from the direct penetration of rainfall through the soil to the water table, by seepage from surface streams or ponds, and/or by subsurface movement from an adjacent groundwater body. Under natural discharge conditions, water is commonly consumed by transpiration of trees and other types of vegetation, by flows from springs, by evaporation from shallow depths below the surface, and seepage into streams that traverse the area.

Jan 1, 1964

By Dirk van Zyl

Natural materials can be used successfully in the construction of heap leach pads. The use of these materials usually result in the least expensive approach for such facilities. Sufficient geotechnical experience has been gained in the design and construction of clay heap leach pads so that they can be used with confidence. A number of operators presently use clay pads in their heap leach facilities; these include Alligator Ridge, Ely, Nevada (gold), and Union Carbide, Gas Hills, Wyoming (uranium). This paper describes the construction and field investigation of a clay pad for the heap leaching of agglomerated precious tailings. The project is located in the Mojave Desert, Southern California. The design had to satisfy operational requirements as well as regulatory requirements. The California Water Quality Control Board (WQCB) was one of the agencies which had to issue a permit for the project. Their biggest concern was the discharge or escape of cyanide into the environment. Rather stringent requirements were therefore placed on the pad design criteria, especially in terms of permeability.

Jan 1, 1983