Search Documents

By D. H. Lynch

This paper is a general description of current Central Florida phosphate mining, beneficiation and product transportation. It is directed and believed to be of interest to engineers not familiar with this industry.

Jan 1, 1978

By R. R. Oder, R. E. Jamison, E. D. Brandner

This paper presents the preliminary test results obtained using a 0.38-kg/s (3,000-lb/hr) beta prototype MagMill. In processing Upper Freeport coal, the beta prototype recovered 82 % of the weight of the feed and 91 % of the heat content while reducing the potential emissions of sulfur by 61%. Pyritic sulfur in the MagMill product was reduced by 78% compared with that in the feed. For all runs, the mill product particle size was controlled to between 70% and 80% -741m (200 mesh). Recoveries of mercury, arsenic and selenium ranged from 35% to 45% of the amounts found in the feed. Power draw was reduced by 26%, and mill throughput was increased by 9% compared to the pulverizer operating with no magnetic separator attached.

Jan 1, 2002

By Calvin L. Stevenson

The probability of a particle passing through a maze is predictable and consistent. This principle may be utilized to effect a particle size separation of materials by presenting a physical maze to a stream of material that will allow the fine particles to pass, while deflecting the coarse particles. A maze is effective even though all apertures encountered are many times larger than the particles being separated. By designing a machine that allows the probability parameters to be controlled and varied without changing physical dimensions, probability sizing becomes a useful tool for the separation of granular materials.

Jan 1, 1967

By D. W. H. Su

"This paper presents the results of a comprehensive study conducted by CONSOL Energy, Marcellus Shale Coalition, and Pennsylvania Coal Association to evaluate the effects of longwall-induced subsurface deformations on the mechanical integrity of shale gas wells drilled over a longwall abutment pillar. The primary objective is to demonstrate that a properly constructed gas well in a standard longwall abutment pillar can maintain mechanical integrity during and after mining operations. A study site was selected over a southwestern Pennsylvania coal mine, which extracts 1,500-ft-wide longwall faces under about 600 feet of cover. Four test wells and four monitoring wells were drilled and installed over a 125-ft by 275-ft centers abutment pillar. In addition to the test wells and monitoring wells, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-ft-wide longwall panels on the south and north sides of the abutment pillar were mined by. To evaluate the resulting coal protection casing profile and lateral displacement, three separate 60-arm caliper surveys were conducted. Prior to the longwall panels being mined by, a number of 3D finite element simulations were conducted to estimate subsidence at the surface, coal pillar pressure increases, the resulting coal protection casing profile and displacement, and the vertical and horizontal displacements in the four monitoring wells. Comparisons of the pre-mining 3D finite element simulation results and the surface/subsurface/underground instrumentation results show that the measured test well and IPI casing deformations and profiles are in reasonable agreement with those predicted by the 3D finite element models, and that the measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models, which serves to validate the 3D finite element models. Parametric studies employing the validated 3D finite element models demonstrate that larger coal protection casing thickness is expected to have little effect on the lateral deformation, although it may reduce the magnitude of casing plastic deformation, and under deeper cover (~1,100 feet), lateral casing deformation is expected to be smaller, although larger plastic casing deformation may be present near the seam level. Also, evaluation of various casing and cementing designs using the validated 3D models clearly indicates that, when all casings are grouted to the surface except the intermediate and production casings, the intermediate and production casings show little deformation and no plastic strain. This research represents a very important step and initiative to utilize the knowledge and science obtained from mining research to improve miner and public safety as well as the safety and health of the oil and gas industries"

Jan 1, 2017

By S. Mojeddifar, N. Ostadmahdi Aragh, M. Hemmati Chegeni

This work integrated selective principal component analysis (SPCA) with a singularity fractal model to map hydrothermal alterations of argillic, phyllic, and propylitic in the north-west of Kerman city in Iran. SPCA results were provided for short wave infrared (SWIR) bands of the Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) sensor tomap phyllic and propylitic alterations. Also, the bands 5–7 were applied to map the argillic alteration zone. SPCA results could present useful information for alteration mapping but it does not show the purest pixels of alteration. Therefore, a fractal model of singularity was applied to highlight the different alteration pixels in the Kerman Cenozoic magmatic arc (KCMA). Thus, the singularity index of different hydrothermal alteration zones was produced. Comparing the obtained results with the field data showed that Kader, Serenu,Meiduk, and Abdar deposits were acceptably identified by alteration mapping. Also, it seems that the singularity index could not discriminate the hydrothermal alterations of argillic and phyllic. The same spectral signature of kaolinite and muscovite minerals is the main reason for misclassifications.

Jul 20, 2020

By William D. Mayercheck

Beginning in 1974, the Bureau of Mines, U.S. Department of the Interior, sponsored R & D efforts related to further development and use of continuous face haulage in underground coal mines (Cowan, 1975). The U.S. Department of Energy continued this effort as of October 1977. This paper represents an update of an article previously published in Mining Engineering magazine (Mayercheck, 1979). Development progress is summarized for a variety of prototype systems or components now being built, surface tested, or tried underground.

Jan 1, 1981

By Ellis J. Brien, O&apos

This afternoon I would like to talk to you about coal, its defi- nition, its constituents, its associated minerals and present and future coal preparation techniques. This discussion will be an attempt at presenting sufficient coal preparation and associated fundamentals to enable you to understand "deep cleaning", a more advanced beneficiation process which will be commercially practiced in the near future.

Jan 1, 1976

Since it was first introduced, the Coal Mine Roof Rating (CMRR) has been widely accepted as a tool for geologic characterization and mine planning. This paper discusses the application of the CMRR to another practical ground control problem. Extended cuts (cuts greater than 6 m (20 ft) in length) are commonly used with remote control continuous miners. Extended cuts can greatly increase productivity, but they have been associated with a number of fatal roof fall accidents. When extended cuts are attempted in weak roof, the roof may collapse before it can be bolted, causing hazardous conditions. Until now, it has not been possible to predict where conditions may not be suitable for extended cuts. In this study, data on the CMRR and extended cut experience were collected at 36 mines in 7 states. It was found that when the CMRR was greater than 55, deep cuts were routine in nearly every case. When the CMRR was less than 37, extended cuts were almost never taken. Between 38 and 55, extended cuts were feasible sometimes but not others. The data also shows that extended cuts are less likely to be stable if either the entry span or the depth of cover increases.

Jan 1, 1998

By D. Chakravarty, G. Samanta, B. Samanta

The present study highlights the planning and design aspects of a well-known openpit copper deposit in India. The mine has been operational since 1982 and presently reaches a depth of 168 m below the surface. The present planning effort has been given due consideration in view of the recent upsurge of copper prices in the global market. The prime focus of the study has been directed towards examining the possible extent of final pit beyond the current pit outline and generating an extraction sequence of future mining operations. To this end, an orebody model of the deposit has been developed and the optimized pit has been derived using L-G 3D algorithm. A sensitivity analysis has also been performed to scrutinize the possible effects of the changing economic scenarios on the ultimate pit configuration. It has been observed that with the current production rate, mine life can be extended another 40 years. With a five-year production plan, these materials can be extracted in eight push-back schemes. The extraction sequence of these push-backs has been outlined in this paper.

Jan 1, 2011

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT The primary objectives of any field data gath¬ering effort should be to (1) identify and gather the data necessary for the project and (2) obtain the data in a state-of-the-art manner. All too often the initial field data are collected both areally and tem¬porally in an illogical manner without the guidance of a conceptual model of the ground water flow systems involved or even a review of existing geo¬logic literature on the area of interest. The initial data collected frequently are of limited value while necessary basic reconnaissance information is miss¬ing. Initial field data should be collected with the intent of developing a hydrologic overview of the potential mine site and surrounding area. Ob¬viously, one of the initial objectives is to define the area requiring a hydrologic investigation. The data requirements should be identified by the time frame in which collection should be made and by the corresponding increase in sophistication of the data requirements with development and operation of the mine. The data requirements are summarized in Table 1. INITIAL LEVEL SITE INVESTIGATION Area Determination The initial task of any hydrogeologic investi¬gation is to determine the boundaries of the area requiring study. Obviously, the site of the proposed mine is included in the study area. The areal extent beyond the site may be determined from an eval¬uation of existing geologic and topographic maps. Those formations that overlie the ore body, the formations containing the ore body, and the formation(s) that lies immediately beneath the ore body are of direct concern for proper site recon¬naissance. Additional formations below the ore body may require study depending upon their thick¬ness, hydraulic conductivity, and degree of inter¬connection with the mine workings. This initial viewpoint identifies hydrostratigraphic units based strictly on geologic concepts such as mineralogy and structure. Formation outcrops, synclines, an¬ticlines, faults, and fracture and joint patterns are used to delineate the area of the site reconnaissance. The simplistic hydrogeologic environment (il¬lustrated in Fig. 3, chapter 2) requires that field data be collected via test wells and/or geophysical techniques. This approach is necessitated by the lack of surface features such as formation outcrops, streams, and springs. Fig. 5 (chapter 2) illustrates a slightly more complex hydrogeologic regime. The potential mine sites at locations A, B, C, D, and E each intercept a different ground water flow sys¬tem or combination of flow systems. Therefore, each mine location requires that a different area and size of area be investigated. A more complex geologic setting as illustrated in Figs. 6 and 7 (chapter 2) may be approached differently. The area included for the site recon¬naissance should encompass sufficient surrounding area to include the outcrops of those formations suspected of being influenced by the future mine. Even adjacent areas not suspected of being influ¬enced may be investigated if the formations of in¬terest crop out in those areas. Such an extension of the area of investigation would provide a greater regional understanding of the hydrogeologic properties of the formations (hydrostratigraphic units) of interest. Geologic Investigation The initial step before conducting the site re¬connaissance is to review all existing literature on the geology of the area. Existing information should be augmented with new exploration data on the dip, strike, thickness, and lateral extent of the for¬mations in the area. Exploration hole logs should be reviewed for indications of lost circulation, rub¬ble zones, and water producing zones. Existing aer¬ial photos such as those available from the US Department of the Interior, EROS Data Center,

Jan 1, 1986

By D. T. Iseley, A. L. Atta-alla

INTRODUCTION The extension project of the East Line Subway of Atlanta's subway network includes the construction of two single track transit tunnels under Interstate Highway 285. The project will be in DeKalb County, Georgia. The length, width, and height of each tunnel are 54.25, 6.3, and 7.2 m (178, 21, and 23 ft) respectively. The ground cover above the tunnel crown ranges from 1.5 to 3.25 m (5 to 11 ft). A soil pillar about 5.5 m (18 ft) wide will remain between the tunnels. The construction of each tunnel includes (i) installation of 21 steel soil support pipes of 75 cm (30 in) diameter, (ii) jet grouting 15 soil cement shafts of 60 cm (24 in) diameter in the soil under the pipes, (iii) contact grouting behind the tunnel lining and between soil support pipes and pavement, (iv) excavation of soil inside the soil support arch, and (v) installation of steel pile foundation, steel sets, and permanent tunnel lining of cast-in-place concrete, all as shown on the cross section in Fig. 1. The soil profile can be described from top to bottom as cement/asphalt concrete pavement, a fill layer consisting mostly of stiff sandy silt/firm silty sand, a residual soil layer consisting mostly of silty sand/sandy silt, partially weathered rock, and solid rock.

Jan 1, 1991

By Mark Laffoon

Gold Fields Operating Co.-Chimney Creek has conducted numerous ore reserve modeling studies In order to optimize the estimates of the gold grades and tonnage distributions. Improved models continue to be produced for the major pits which Increase confidence levels required by Gold Fields management and provide the basis for more accurate long and intermediate term mine planning. Various kriging and non-kriging estimation techniques are used at Gold Fields -Chimney Creek Mine. This paper reviews the modeling histories and, current procedures used to construct these models with particular emphasis on the North Pit deposit.

Jan 1, 1991

By P. H. S. W. Kulatilake

The presence of discontinuities strongly affects the mechanical and hydraulic behavior of rock masses. Joint geometry networks play a vital role in civil, mining, and petroleum engineering projects associated with jointed rock. The need for a realistic representation of joint geometry in rock masses has been recognized. The first part of the paper shows how to build three-dimensional stochastic joint network schemes and also shows how to perform validation studies for these schemes using joint data from the Stripa mine, Sweden. Due to the existence of complex joint patterns, mechanical behavior of jointed rock masses usually exhibit scale effects and an-isotropic properties. A correct understanding of the mechanical properties (strength and deformability) of jointed rock masses is important for designing and performance estimation of structures build in and on rock masses. Beyond a certain volume, the mass proper-ties of the rock may remain essentially constant with respect to the effect of joints. This minimum volume may be used as the element size to represent the equivalent properties of a statistically homogeneous rock mass volume which contains a significant number of joints. This volume may be termed as a "Representative Elementary Volume" (REV) and may be of great importance for engineering purposes. Investigations are underway at both the 2D and 3D levels to look into the possibility of establishing relationships between REV mechanical properties and joint geometry parameters. Recently developed joint geometry modeling schemes are linked with existing distinct element codes (both 2D and 3D) to create a stochastic/deterministic stress analysis approach in achieving the goal. Results obtained so far in this direction are presented in the second part of the paper.

Jan 1, 1992

By L. A. Bellows

The "Athabasca oil sands" of the McMurray formation in northeastern Alberta cover an area of about 21,000 square miles and contain the world's largest reserve of oil. Fort McMurray, a small town in the heart of the oil sands area, is about 235 air miles north- east of Edmonton. A railway serves the town but no year-round roads connect the town with the rest of Alberta. (Figure 1). The McMurray formation is of early Cretaceous age, deposited unconformably on a limestone surface of Devonian age. The sediments appear to have originated from the Canadian Shield to the east and were deposited in bays and deltas of large fresh water lakes. The lakes were later replaced by marine seas in which t the overlying Clearwater shale was deposited. (Figure 2).

Jan 1, 1963

By NILAMADHABA SAHU, Gajanan U. Kapure, Pankaj Kumar, Sunil Kumar Tripathy

Chromite ore processing tailings and low-grade manganese ores are typically considered waste due to their limited or negligible utility, leading to environmental and storage concerns. Researchers globally have explored various methods to utilize or upgrade these wastes, particularly because dumping chromite ore has been linked to severe health issues through Cr(VI) leaching. Individually, these ores lack economic value, and there has not been research on simultaneously reducing both low-grade ores. In this study, the focus lies on smelting these ores together, aiming to create a precursor alloy for 200 series stainless steel scrap. Initial research indicates the potential for scrap formation, validated through laboratory experiments with varying coke rate, basicity and holding time. The investigation discovered that smelting this combination could yield a metal product consisting of 59 percent Fe, 24.93 percent Cr, 7.56 percent Mn, 0.62 percent Ni and 0.93 percent Si. The optimum basicity was found to be 0.6 with 80 percent recovery. Notably, this process eliminates intermediate steps in 200 series stainless steel production, potentially reducing overall carbon dioxide emissions. This proposed method represents a cleaner, sustainable approach to repurpose these two waste ores, projecting a net profit of US$330/t.

May 1, 2024

By Michael J. Mankosa

Carpco has recently evaluated the use of various mineral processing techniques for secondary materials recovery. These applications include recycled foundry sands, plastics and secondary metals. This paper describes different recycling applications and the associated separation solutions. Results from extensive laboratory-and pilot-scale test work in each area are discussed. Industrial installations resulting from this test work will be presented. A detailed description of an industrial installation patented by Carpco for the recovery of plastic and metallics from current waste by-products is presented.

Jan 1, 1997

By Miche1 Dagbert

In most open pit operations mining porphyry type deposits, production planning rests on an are reserve inventory block file which is derived from diamond drill hole data. With such a practice, the way by which block values are generated is critical and in the recent years many studies deal with the comparison of different estimation methods for block grades (Mueller, E. (1), Knudsen et al (2) (3), Barnes, (4), Williamson and Mueller (5). Typically in such studies, one selects a bench or a group of benches where there is a "sufficient" number of blast holes (BH) with assay values in each of the blocks (generally 30.5 x 30.5 m (100 x 100 ft) or 15.2 x15.2 m (50 x50 ft). Then the arithmetic mean of the BH values in each block is computed and it is assumed to represent the real block grade against which different estimated values are compared. However it is sometimes observed that the variation of these BH values within a block is high and that their arithmetic average may significantly differ from the real average grade of the block (Barnes (4). The problem of the precision of the mean BH grade in a block has been examined by Williamson and Langlois (6) in an experimental way. They strove to find a better estimate of the average block grade than the mean BH grade but their results were not conclusive. The purpose of this study is to investigate the same problem within the frame of geostatistical models (David (7). Besides practical results obtained with these models, two general points are emphasized and illustrated in the text. First, "good results" are obtained if "good geostatistics" is done (David et al (8).

Jan 1, 1978

By E. h. Erwin Gaertner

Before dealing with the technical equipment of this paper a short survey of the Rhenish Brown Coal Area is given in order to illustrate the special geologic and environmental conditions in this region, which led to the development of the mining technics, used today.

Jan 1, 1975

By L. D. Savage

Several experiments were conducted using a large crib fire adjacent to a Kennedy Metal Products steel stopping in a simulated cross cut to evaluate the proposed mechanisms by which a mine fire would breach the stopping. Temperatures in the convective air paths on both sides of the stopping, at the surface of the roof and 16mm within the roof were measured to evaluate the effects of heat transfer. The results indicate that roof failure is the prime method of breaching this design of stopping.

Jan 1, 1996

By J. E. Golsan

Barrick Gold Corporation installed an expert style control system on the grinding circuit at its Mercur mine. Barrick's main objective was to increase mill throughput by a minimum of 3%. The expert system team collected operating data and then created a knowledge base using Comdale/X expert system development software. The expert system moved from on-line "advisory" mode, testing of expert rules, to full process control in four weeks. Expert system control benefits include a 9-15% increase in mill throughput, consistent mill loading leading to less wear on SAG mill parts, and improved downstream process control.

Jan 1, 1998