Search Documents

By Ravi Shah, Augusto Lucarelli, Daniele Peila

"In mechanized tunneling the annular gap between the segmental lining and the surrounding soil caused by tunnel driving, must be backfilled almost instantaneously with an adequate grouting mortar. The objective of this research is to perform a fully three dimensional modeled parametric study using FLAC 3D and evaluate the effects of backfill grouting on the tunneling performance. The research focuses on comparisons between different injection materials and state-of-the-art Bi-Component grout and their effects on the settlements on the surface. The research consists of testing a regular situation of tunnel excavation using a shielded machine with face under pressure. The tunnel dimensions and the soil properties are selected as close as possible to the reality and based on Turin Metro case. 1 INTRODUCTION Excavation of tunnels in urban areas can induce ground movements, which have negative effects on existing structures. In such scenarios, shield tunneling has become a well-accepted construction method in various ground conditions. It is characterized by relatively complex interactions between the soil, the tunnel boring machine (TBM) itself, the tunnel lining and the tail void grout. The problem to control the settlement depends on the face pressure, ground properties and back filling procedure and material of the tail void. The face pressure acts against the front to guarantee the face stability. In case of EPB TBMs the stability of the tunnel face is ensured through the excavated soil itself, which is conditioned and is maintained in compressed state within the excavation chamber. When excavating with TBMs a tail void is created between ground and the lining (Fig.1) after the TBM excavation and ring assembly that must be backfilled instantaneously by injecting the backfill material through the TBM’s tail shield. The process is of primary importance as it reduces the surface settlements and creates an immediate link between the ground and lining, sealing against ground water and leakage, reducing the differential movements between segments and providing long-term stability. The most used backfilling materials are: Inert mixtures that do not contain cement instead sometimes they are replaced by fly ash or other substitutes. A typical design of an inert mortar consists of sand, fly ash, bentonite and water. Pea gravel, which is constituted of granular materials with grain size ranging from 8 to 12 mm. This mixture is highly recommended for tunnels being constructed in rock mass with little deformation rates.Cement mortar is composed of cement, water, aggregates and sometimes bentonite. Cement controls the principle mechanical property of the mix, which can reach high values of 15-20 MPa in 28 days. The aggregates contribute towards the shear strength and reduce the pumpablity of the mix (Thewes and Budach, 2009). The reduced active systems have a cement content of 50-100 kg/m3, whereas the active system the binder component derives full hydration with cement content of over 200 kg/m3 ."

Jan 1, 2016

By J. W. Scott

The problems involved in installing, maintaining, and operating large vibrating screens have been summarized and discussed, based on a survey of current use of such screens in selected North American mineral processing applications. Practical, effective solutions for the more serious common problems are described, along with some recommendations on design practice for specifying, selecting, and installing large screens.

Jan 1, 1983

By O. Akinkugbe

The safe, productive exploitation of coal in multiple-seam situations requires specific design technology. At present, there are two general design approaches that the mining engineer can use to analyze the multiple-seam problem in question, either simple empirical relationships or complex numerical models. Often, the empirical approaches are too general for the specific problem and the numerical models require too much time and expertise for the practicing engineer. In this paper, a new program designed for quickly and easily calculating the stresses, strains, and safety factors associated with basic multiple-seam mining situations is presented. The program implements a simplified, two-dimensional boundary-element method in order to model the complex multiple-seam stress and displacement interactions. The program incorporates automatic coal and gob property generation to simplify the input, and inherently calculates pillar safety factors to enhance the output.

Jan 1, 2004

By I. Iwasaki

The effects of percent solids, mill loading and grinding time on product size distribution and ball wear were studied in a laboratory ball mill for a taconite ore. Mild steel balls and HCLA steel balls were used to examine the role that ball hardness play in grinding. Net production of minus 325 mesh - material reached maximum at 70% solids, whereas the ball wear decreased as pulp density increased. HCLA steel balls ground the taconite ore finer than mild steel balls under otherwise identical conditions. Examination of ball surfaces with a scanning electron microscope suggested that grinding with mild steel balls involved nipping rather than attrition, whereas grinding with harder HCLA balls involved both nipping and attrition.

Jan 1, 1984

By David A. Milligan, William Cobb

2.1 INTRODUCTION This chapter provides the reader with a sense of how a heap leach project may make an orderly, and hopefully non-traumatic, transition from discovery or acquisition to project construction. In making this transition a project can pass through several project development phases (i.e. ore definition and delineation, conceptual engineering, detailed engineering, and ultimately on to project construction and operation). "Go" or "no go" decisions may occur at any point in each of these phases. The transition from ore definition to detailed engineering should be accomplished via a well thought out program of interdisciplinary studies and an integrated, interdisciplinary project team. This chapter also describes, in general terms, a "roadmap" approach to the project evaluation process that must occur as project planning and development progress. It is the experience of the authors, as well as a myriad of companies who have been through the heap leach project development process, that a systematic approach will save many headaches, and many dollars. In fact, it is safe to say that a project with no formalized system of "objectives setting" and "milestone charting" may well flounder along the way, even if an economic ore body exists. Many papers and technical articles have been written about various aspects of mineral resource appraisal, economic evaluation, and mine development. Most of these invoke the same general philosophy of a systematic approach to project evaluation and development, although methods cited for attaining goals are quite variable. This is undoubtedly appropriate, given the fact that there is great variation in approach to project development (e.g., climatic considerations, ore body size and physical ore characteristics, permitting constraints, etc.). For the purposes of this chapter, two primary sources of information have been used to highlight the "road map" approach previously alluded to. These sources are cited throughout the text as Mackenzie (1980) and Snow and Michel s (1986). A brief summary of each of these sources is provided below: Brian GJ. Mackenzie of Queens University (Mackenzie, 1980) has developed a wealth of information concerning project development topics. Much of this information is synthesized in his notes for a short course entitled : "Mineral Exploration Planning and Economic

Jan 1, 1988

By A. Bhatanagar, D. Makhija, A. K. Mukherjee, R. K. Rath, P. Dixit

Characterization and beneficiation of dry iron ore processing plant reject fines of Khondbond region, India, was investigated. Different characterization techniques viz. size analysis, size-wise chemical and density analysis, X-ray diffraction analysis, sinkfloat analysis, thermo gravimetric analysis, scanning electron microscopy, and QEMSCAN were carried out. Based on characterization results, two process flow sheets comprising wet screening followed by conventional gravity concentration and two stage classification with different beneficiation routes were used to recover the iron values from reject fines containing 58.73% Fe, 5.54% Al2O3, and 6.6% SiO2. Finally, suggested flow sheet comprising of two stage classification and advance gravity concentration followed by the combination of grinding, classification, and froth flotation produced iron concentrate of 2.36% Al2O3 with 75.8% yield which can be used in sinter/pellet making.

By E. R. Spencer, E. R. Bauer, G. P. Cole

Overexposure to hazardous noise has been found in most mining sectors, with up to 100% of the surveyed workforce experiencing a noise dose that exceeds the U.S. Mine Safety and Health Administration (MSHA) permissible exposure level (PEL). As a result, miners show elevated rates of hearing impairment of 70-90% by retirement age. To help manage noise exposures, the U.S. National Institute for Occupational Safety and Health (NIOSH) developed the Determination of Sound Exposures (DOSES) software and implementation guide for use by mine management and safety personnel. This paper describes the development, functions and basic operation of the initial-release version of DOSES. A revised version is being developed to incorporate additional user-suggested functions, and its development and implementation to assess noise control solutions will be described in a future article. The software relies on a time-motion study that profiles the worker’s daily activities. Observations about the worker’s location and tasks or other activities are recorded along with the start and end time, to determine the duration of the tasks so they can later be matched up with the noise data. The software gives the user the option of assessing dose relative to the MSHA PEL, the action level or the NIOSH recommended exposure limit. The software generates a variety of interactive on-screen displays showing where, when and how the worker’s noise dose accumulated. It also can generate customizable printed reports. These outputs can be used to highlight the tasks, locations and times that are associated with the greatest amount of a worker’s noise exposure. DOSES simplifies and streamlines the record keeping and analysis associated with time-motion studies and worker noise exposures, so mine management can make engineering noise control or administrative control decisions to limit the noise overexposure of their workers.

Jan 1, 2011

By H. Huang, R. N. Gow

"EH-pH diagrams are useful tools in understanding how mineral surfaces react in solution and particularly how aqueous conditions can be changed to enhance mineral leaching processes. Successful application of these diagrams, however, requires that several considerations be kept in mind to prevent what had been termed as “gross errors” in their calculation and use. In this paper, the aqueous Cu-S system is used as the basis for explaining the mass-balanced method of calculating EH-pH diagrams with the STABCAL thermodynamic equilibrium software. A breakdown of the Gibbs’ Phase Rule and how it is used in STABCAL to modify the diagrams is included. The methodology was applied to the aqueous Cu-As-S system, and resulting diagrams were compared against examples of those generated using the predominant-ion method. The complexity of such diagrams increases with every additional component, and competition between species becomes more apparent, as can be seen by curvature in the resulting mass-balanced diagrams. The complete diagram for enargite (Cu3AsS4) is shown. It compares well with spectroelectrochemical measurements from Raman spectroscopy and cyclic voltammetry studies.IntroductionInnovation in the field of processing arsenicbearing copper ores has been of particular interest. Copper arsenic sulfosalt minerals such as enargite (Cu3AsS4) and tennanite (Cu12As4S13) are now frequently prevalent in ore bodies as the oxide and easily leachable sulfides become harder to find. These minerals, unless pretreated somehow, concentrate in copper sulfide flotation processes, in turn concentrating the arsenic levels. Increasing environmental restrictions on arsenic content for smelters makes the hydrometallurgical processing of these concentrates more favorable. While enargite is considered one of the more refractory copper sulfides, more so than chalcopyrite (CuFeS2), there are still several methods, both industrially proven and in development, that are capable of processing these ore types. Alkaline sulfide leaching can be used as a pretreatment method to solubilize arsenic selectively (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp, Takasaki and Shibayama, 2010a, 2010b), or the entire metal content can be leached using acid-type leaches such as acidified ferric sulfate (Dutrizac, 1981; Hackl et al., 1995; Klauber, 2008), or the chloride assisted, CESL (McDonald and Muir, 2007) or nitrogen species catalyzed (Anderson, 2003) processes can be used.As development of these leaching technologies proceed, it is also important to develop an understanding of the mineral thermodynamics. To date, there are numerous studies on the Cu-Fe-S-H2O system, particularly as it relates to chalcopyrite leaching, yet few studies have done on the Cu-As-S-H2O system. Computer-generated EH-pH diagrams have been employed to illustrate the importance of thermodynamic calculations in providing insight into such a system."

Jan 1, 2016

By Kwangmin Kim, Junnhyeok Park

In the hard-rock mining industry, the generation of fines during blasting is an important issue because it has a significant effect on production processes. Although various approaches have been used to estimate fines generation in recent decades, as a practical matter, measuring the amount of fines is nearly impossible given the technical limitations and the scale of mine blasts. In this study, a dynamic PPV damagemodel was developed and applied to predict fines generation as a result of blasting. This modified version of the crushed zone model (CZM) considers dynamic rock properties and peak particle velocity (PPV), which represents the induced stress in blasting. Dynamic rock-fracturing tests were conducted using a split Hopkinson pressure bar (SHPB) to determine the parameters that represent the relationships between rock strength and strain rate as well as the relationships between fines amount and strain rate in the model. A case study was conducted that entailed determining the radius of the crushed zone for given blast designs and rock properties and then measuring the fines amount within this crushed zone. This case study indicated that the dynamic PPV model can provide a rough estimate of fines generation for given dynamic rock properties and blast design parameters and that this method has the potential to be a useful indicator, or index, of fines generation.

May 16, 2020

By William J. Almas

Operating uranium mill tailings containment and mill decommissioning activities are regulated by the Nuclear Regulatory Commission (NRC) and the Environmental Protection Agency (EPA) through numerous regulatory mechanisms. Reduction of radon emissions from tailings disposal areas, remedial actions to return groundwater to baseline constituent concentrations, and 200-to 1,000-year stabilization of tailings are major focus areas of regulation. The cumulative economic impact and uncertainty associated with regulation are very significant and will hinder future development of uranium milling facilities.

Jan 1, 1991

By Lorraine B. Burgin

The extensive lead time to develop most Arizona copper deposits commenced with initial production efforts before the turn of the century, when the first attempts were made to recover gold and silver and later copper from the high-grade vein deposits of the territory. Each of these discoveries, prospects, and early operations had its own lead time and life cycle as economic production was attempted. Because prices of the metals fluctuated and the higher grade material was depleted, economics forced operations to close and companies to fail. Renewed interest in the property because of improved conditions, different interpretation of the geologic structure, or new promotional ability frequently resulted in the formation of yet another company to finance the exploration and, hopefully, the development of the property. This cycle of renewed activity and subsequent abandonment was and is common, accounting for many lead times and for the long period of time from the initial location of claims to large-scale production. In order to gain a perspective on the lead-time interval necessary to achieve development of a large-scale operation, the histories of several major Arizona mines were examined, rather than a simple listing of discovery and production dates of many mines to arrive at a statistical average. The Miami, Castle Dome, Copper Cities, San Manuel, and Twin Buttes properties were studied, and as much data as possible obtained on the Pinto Valley, Esperanza, Sierrita, Pima, and Mineral Park-Ithaca Peak properties.

Jan 1, 1974

By M. D. Carter

The availability of environmentally acceptable and reliable energy sources is an important issue for Federal, State, and local planners. A cooperative program by the U.S. Geological Survey, State geological surveys, and the U.S. Bureau of Mines has developed a national GIS-based systematic effort to collect, analyze, and depict data characterizing the relationship between restrictions to mining and the potential development of the Nation's coal resources. Land use/environmental and technologic/geologic restrictions are identified within selected 1:24,000-scale, 130-to 150-sq-km 7.5-min quadrangles and applied as overlays to maps of coal-bed thickness, depth, and mined-out areas. Tonnages of original, mined and lost-in-mining, remaining, restricted, and available resources are calculated. Resultant data files are transferred to the Bureau of Mines for recoverability and cost analysis.

Jan 1, 1995

By Farzad Moradpouri, Kianoush Barani, M. R. Azadi

The aim of this paper is to assess the effect of microwave treatment on copper sulfide ore for ball milling and bed breakage. Liberation analysis of ground products in eight size fractions showed that microwave pretreatment liberated more chalcopyrite particles from the bed breakage product than the ball mill product. In bed breakage, microwave pretreatment caused a 2% increase in chalcopyrite liberation on average. Microwave pretreatment produces more elongated particles in ball milling and more rounded particles in bed breakage, respectively. Microwave pretreatment produces coarser chalcopyrite particles with a wide range of sizes. This effect is more significant in bed breakage compared with ball milling. Micro-flotation test results showed that in ball milling, treated and untreated materials have similar metallurgical performance and there is a little difference (1%) between the average Cu recovery values. However, in bed breakage, the average recovery for the treated materials is about 5% higher than the untreated materials.

Jul 8, 2021

By R. W. Wittkopp

The Relief Canyon gold deposit is located approximately twenty- four kilometers east of the town of Lovelock in Northwestern Nevada. At Relief Canyon, the Late Triassic Grass Valley Formation has been thrust over the Late Triassic Natchez Pass Formation. The lower plate Natchez Pass Formation is composed of massive gray dolomitic limestone which is locally silty and sandy. The upper plate Grass Valley Formation is composed of shale, siltstone, argillite and quartzite. Gold mineralization at Relief Canyon occurs along the highly brecciated thrust contact between these two formations. Weak gold mineralization often occurs above the thrust in the Grass Valley Formation, however, most of the ore grade mineralization is present below the thrust in the brecciated Natchez Pass Formation or where the two formations are mixed as a result of movement along the thrust. Several types of gold mineralization have been recognized at Relief Canyon. A large amount of the ore is present as a jasperoid breccia, however, significant amounts of ore occur as a mixed breccia composed of upper plate rock, fresh limestone, clay and jasperoid breccia. Gold ore also occurs in a fresh limestone breccia which contains a large amount of clay. Below masses of jasperoid, jasperoid stringers containing gold extend into the fresh limestone. Gold mineralization at Relief Canyon appears to be truly disseminated and has the typically associated trace elements of arsenic, antimony, mercury and fluorine. The Relief Canyon deposit can be classified as a structurally controlled disseminated gold deposit. Other deposits that fit this classification are the Pinson and Dee gold mines.

Jan 1, 1984

By B. J. S. Sceresini

The Filblast Cyanidation Process incorporates the advantages of intense high shear mixing, high dissolved oxygen concentra­tion and high pressure to achieve extremely rapid gold dissolu­tion rates. This is made possible without suffering from high energy or wear rates by the unique design of the Filblast gas shear reactor. The reactor is a rugged and compact in-line device which can be constructed from a variety of wear and chemical resistant materials. High temperature tolerance is also possible so that the device can be incorporated into a pressure leach circuit with significant capital cost savings because of the high capacity to volume ratio that is an inherent feature of the device. For cyanidation applications the outer casing is protected by a polyurethane coating and the internal parts are of wear resistant polymer. The largest unit built to date has overall dimensions of 1200 mm length by 300 mm diameter and has a capacity of about 150 dry tonnes per hour at 40-45 % solids. Service life at this throughput is at least three months. Six mines are currently employing the Filblast Process and another six are conducting plant trials. The ore types range from highly reactive, almost impossible to treat, pyrrhotite/ arsenopy­rite to deeply weathered clay ore which forms a highly viscous pulp. It has been found that the effect of shear thinning has resulted in improved leaching and adsorption kinetics resulting in higher carbon loading and reduced soluble gold loss. Total tonnage treated is approximately eight million tonnes per annum. This paper presents the operating benefits and cost savings which have been achieved in four plants, two treating oxide/ sulphide ore blends and two treating highly reactive sulphide ore and concentrate. Filblast leasing and maintenance charges and pump operating costs are about ten percent of the benefits. A conceptual cyanidation circuit based on the Filblast Cyanidation Process is also discussed. The Filblast System is an in-line pressure leach aerator/ reactor which generates very high shear and greatly enhances mass transfer rate by generating extremely small gas particles where oxygen gas is required for oxidation reactions and/or utilising the high shear characteristics to minimise the diffusion boundary layer. Both of these rate limiting factors effect the rate mechanism for gold cyanidation. Initially two multi-stage Filblast aerator cartridges formed a leach train but now the trend is to install a single submersible cartridge of equivalent perfor­mance. This design simplifies installation and minimises change-out times. However the in-line concept can be employed where high pressure leaching or pressure oxidation is required. The reactor is submerged in the leach tank so that the mass of gas micro-bubbles contained in the discharging slurry is entrained in the agitator vortex and is thoroughly dispersed throughout the tank. A diagrammatic representation of a leaching circuit incorpo­rating the Filblast Reactor is shown in Figure 1. The recirculation pump takes new feed directly from the cyclone overflow trash screen either under gravity or pump fed and recirculates the balance to maintain 250 - 270 m3/h total slurry flow. All of the leach feed slurry gets at least one pass through the Filblast thereby eliminating short-circuiting. Typically a 6/4 EAH Warman pump drawing 60-70 kW is required to circulate 250 m3/h through the system. The back pressure generated by the Filblast is in the range of 400-500 kPa depending upon pumping rate, pulp density and slurry rheology. The high shearing rate effectively negates the viscous effect of slurries and the addition of a gas further reduces the pulp density by virtue of the intensely aerated, homogeneous medium. The gold leaching Filblast cartridge elements are made of polyurethane but stainless steel, ni-hard, rubber or ceramics can be used depending on the operating temperature and design duty. The efficiency of the Filblast Leach Reactor in gold cyani­dation is due to the extremely efficient mixing, oxygen dissolu­tion and surface polishing action of the Filblast design. Either air or oxygen may be used but Atomaer recommend the use of oxygen because of the rate benefits gained from cyaniding at [02] significantly > 20 ppm D O in the reactor. Very high DO concentrations have been measured; in excess of 50 ppm. There is some debate as to whether the value is a true measure of the DO or the oxygen meter sensor is measuring the effect of a mass of very fine bubbles of free oxygen. Regardless of the fact the reactor has registered some amazing gold dissolution rates commonly in excess of 80 % during transit of the pulp through the reactor. The elapsed time is less than half a second!

Jan 1, 1995

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By D. Kelley

Due to pricing volatility and lack of availability of metals, the use of non-metallic materials of construction in metal extraction and refining processes has increased significantly in recent years Even though costs and availability of metals has improved recently, these factors are not expected to continue into the future as metal supplies once again fall short of global demand. One of the most common non-metallic materials of construction used in metal extraction and refining processes today is Fiberglass- Reinforced Plastic (FRP). These processes often require materials of construction that can resist acids and high concentrations of acid chloride salts. As shown in Table 1, FRP based on epoxy vinyl ester resin has the same chemical resistance to acid and better resistance to acid chloride salts than alloy C-276 and is superior to 2205 stainless steel in both cases.

Jan 1, 2010

By J. L. Coburn

The Huari-Huari ore body is located in Southern Bolivia, at an elevation of approximately 3,800 meters above sea level. The ore is a complex massive sulfide, slightly marmatitic sphalerite, in a fault fissure filled hypo- thermal vein in Paleozoic shales and quartzite-altered sandstone. The sphalerite has common associations with pyrite and quartz and is frequently intricately intergrown with stannite, chalcopyrite, and pyrrhotite. The sphalerite also contains numerous inclusions of pyrite, marcasite, galena, boulangerite, jamesonite, quartz, arsenopyrite, and cassiterite. A research program was undertaken to develop a flowsheet for the recovery of separate silver, zinc, and tin concentrates by selective flotation. Based on this experimental work and subsequent flowsheet development, engineering and construction of a 500 metric ton per day concentrator was undertaken. This paper describes the process that was developed for the Huari-Huari ore and the unique aspects of the Huari-Huari concentrator.

Jan 1, 1977

By K. E. Hjelmstad, W. H. Pomroy

In the event of fire underground, it is essential that all miners be warned as quickly as possible. With mine air rapidly depleted of oxygen and contaminated with smoke and toxic fire gases, any delay in the warning signal could have disastrous consequences. Unfortunately, present mine fire warning systems, such as stench, audible or visual alarms, telephones, and messengers, are often slow, unreliable, and limited in coverage. Recent research by the US Bureau of Mines has established the feasibility of ultralow frequency electromagnetic signaling for underground mine fire warning. Infield testing completed thus far at five mines, signals of from 630 Hz to 2000 Hz were transmitted through rock up to distances of 1645 m (5400 ft) to a pencil-sized ferrite-core receiving antenna and intrinsically safe receiver circuit. Theoretical analysis indicates a capability to transmit effectively for distances in excess of the maximum depths of most American mines, which is about 900 to 1000 m (2950 to 3280 ft) . The prototype system uses off-the-shelf components and state-of-the-art technology to ensure high reliability and low cost. This technology would enable simultaneous and instantaneous warning of all underground personnel, thereby in- creasing the likelihood of successfully evacuating a mine during a disaster. This report discusses the theoretical basis for through-the-rock ultralow frequency electromagnetic transmission, design of the prototype transmitter and receiver, and the results of in-mine tests of the prototype system.

Jan 1, 1991

By G. W. Kenzy

Recently, in the United States, questions of possible deleterious synergistic health effects of the gaseous and particulate components in the diesel exhaust and mineral and coal dust have been the impetus for extensive research by several agencies. At the present time, diesel engines are tested and approved for use in gassy and non-gassy underground metal and non-metal mines under Parts 31, 32, and 36 of Title30 of the Code of Federal Regulations. Diesel-powered equipment for use in underground coal mines, though not explicitly addressed in the law, is administered under Parts 32 and 36 of Title 30, with Part 36 being applied in the case of equipment working inby the last open crosscut or in the return airways. Operation of diesel equipment in underground mines has the potential for serious health and safety hazards from the gases, vapors, and particulates in the exhaust. Therefore, various countries have rules and regulations for the safe deployment of diesel equipment. The applicable laws and regulations from several countries who have long experience with diesel-powered equipment in their mines are reviewed. Four major areas have been addressed: (1) testing and approval procedures of diesel engines, (2) ambient mine air quality specifications, (3) frequency of sampling and location of samples, and (4) air quality specifications in splits where diesel-powered equipment are operated. The review indicates that most regulations generally consider four possible hazards: (1) toxic components in the engine exhaust, (2) ignition of flammable atmospheres by the engine or electrical equipment, (3) fire hazards presented by the engine fuel oil and by combustible material that might come in contact with the equipment, and (4) mechanical hazards. There is a remarkable similarity in the laws with regard to engine design, testing and approval procedures. However, the aspects with regard to mine air quality and quantity are quite variable-- from a general statement to very specific standards for many different diesel exhaust constituents. However, the laws with regard to synergistic effects of diesel exhaust components and other mine air contaminants are an exception.

Jan 1, 1980