Search Documents

By V. de Ruiter

In the northwestern part of the Netherlands lies the deepest solution salt mine in the world. The company operating the mine is Frisia Zout bv (part of the K+S group). Extracting the NaCl from caverns at a depth of nearly 3000 m has a lot of challenges. Continuously monitoring, among others, the flows, pressures and salt concentrations is necessary to safely and economically mine the salt. A system has been set up at Frisia to be able to monitor the data from a distance. Data has been put in graphs to monitor the trends daily. All gauges are also continuously monitored to maintain accuracy. With this system a better understanding of the mining process has been made and has led to many optimizations.

Jan 1, 2008

By K. Hanumantha Rao, K. S. E. Forssberg

The separation of feldspars from quartz has been the subject of numerous studies since 1930 and the flotation process so far proved to be the most suitable method. In the conventional process, feldspars are separated from quartz using a cationic collector and hydrofluoric acid as an activator of feldspars. There is no general agreement on the mechanism of fluoride activation of feldspar surfaces and the role of fluoride ions is briefly discussed. The use of HF is no longer acceptable due to environmental and health problems, and a few new reagents schemes have been reported. The available evidence shows that the success of these new reagent schemes is very limited. A new reagent scheme which is environmentally safe and cost effective for the separation of feldspars from quartz is yet to be resolved.

Jan 1, 1994

By Donald C. Strimbeck

The Bureau of Mines, U.S. Department of the Interior, is conducting research and development on a coal-burning gas turbine. This work includes the development of (1) turbine blades resistant to coal ash erosion, (2) equipment to feed coal under pressure to a turbine, (3) an efficient combustion system, and (4) equipment to remove coal ash from the gases that drive the turbine. Initial emphasis is being placed on testing the first turbine ever equipped with blades designed specifically for use with coal as the fuel. Operating tests with this turbine are now in progress. This paper describes the Bureau's coal-burning gas turbine development program and progress on this operating test.

Jan 1, 1964

By F. N. Kissell

U.A. Mine Safety and Health Administration (MSHA) coal dust compliance data sometimes shows high silica levels at roof bolters. However, it is unclear whether this silica normally originates from the bolter itself or from other dust sources upwind of the bolter research studies to answer this question at individual mines have been conducted. However, operational practices vary from mine to mine thus, the information gleaned from any one study cannot be accurately extrapolated to describe silica dust sources in most mines. In this paper, three decades of bolter dust research are reviewed the results showed that, while inadequate maintenance on the bolter dust collection system can result in excessive dust, more likely reasons for high silica levels are inadequate ventilation of the mine entries being bolted and dust traveling downwind from the continuous miner to the bolter. Scrubbers on continuous miners may not be removing as much silica dust as expected. Mining Engineering, 2011, Vol. 63, No. 10, pp. 78-82. Official publication of the Society for Mining, Metallurgy and exploration, Inc.

Jan 1, 2011

By A. Vilinska

The adhesion of Leptospirillum ferrooxidans bacterial cells onto the sulfide minerals pyrite and chalcopyrite was evaluated using two different physical-chemical approaches; thermodynamic and extended DLVO theory. For the parameters incorporated into calculations, the zeta potentials and contact angles of powdered solids and bacterial cells were acquired experimentally. The Hamaker constants essential for Lifshitz-van der Waals inter-action calculations were calculated following two different methods: macroscopic and microscopic. Adsorption tests were carried out at physiologic conditions to estimate the amount of cells adsorbed onto a mineral surface and the extent of alteration of that mineral surface in biobeneficiation. The free energy of adhesion was found to be negative for both minerals, indicating that the adhesion is energetically favored and preferred. The interaction energy diagrams of the total interacting force was also negative for the cases where the particles were charged oppositely; in the remaining cases, the total force was attractive after overcoming an energetic barrier caused by the repulsive electrostatic forces. Under the conditions of the adsorption test, the experimental results are in agreement with the theoretical; this suggests that the physical-chemical forces are crucial for bacterial adhesion.

Jan 1, 2011

By F. W. Bond

Predictive ground-water modeling is currently being applied to a wide range of engineering applications. In recent years models have been used to evaluate the effect of large ground-water withdrawals on regional water supplies; subsidence associated with overpumping; siting and design studies for chemical dumps; siting and safety aspects of nuclear waste storage; and heavy metal migration from disposal sites. Similar modeling techniques could be used to analyze water-related problems in the minerals industry such as mine dewatering (both open pit and underground), environmental and pollution control, and process water supply and disposal The objective of this discussion is to describe how ground-water models are being used to assist in the solution of water-related problems outside the industry and to extrapolate that use to mining problems.

Jan 1, 1980

By Luzheng Chen

The study aimed to evaluate the separation performance of a full-scale continuous centrifugal concentrator in the reconcentration of fine hematite from high-gradient magnetic separation (HGMS) concentrate in a tailings recovery plant, and to investigate the usefulness of the technology in industrial applications. The effect of changing the operating variables on concentrate grade and recovery was studied. The results indicate that among the variables considered in the study (water spray pressure, centrifugal acceleration, feed volume flow rate, feed percent solids and the reciprocation and spacing of water sprays), the change in centrifugal acceleration affects the recovery the most and continuous concentration can be achieved only when the water spray has a sufficient pressure. In addition, the reciprocation and spacing of the water sprays have a significant influence on the concentrate grade. Although performance of the full-scale concentrator is slightly inferior to pilot-scale trials, due to limitations in the scale-up design and the fluctuations of feed material characteristics, this concentrator provides a potential way to achieve continuous concentration and obtain a high-grade concentrate from tailings.

Jan 1, 2010

By Robert L. Zook

Coal refuse slurry impoundments are dams constructed of coarse coal refuse to impound fine refuse (slurry) and water (25-30% solids). Both products are waste from coal preparation plants. A number of these structures in West Virginia, Pennsylvania and Kentucky were investigated to determine embankment stability. During the investigation a variety of embankment designs were encountered. The investigation determined the soil and geological characteristics of the embankments and the sites. This was accomplished by a test drilling and monitor installation (observation wells and piezometers) program, geologic study, and large scale mapping which allowed sub-surface profiles of the embankments to be constructed. The laboratory testing program concentrated on textural classification of the coal refuse, permeability and determining strength parameters to be utilized in the stability analyses. For the stability analyses, the Modified Fellinius Slip Circle, Simplified Bishop Slip Circle and Analysis for Translational Failure -were utilized. In all stability analyses hydrostatic pressure and earthquake were considered. This investigation indicated that 62% of the embankments analyzed are in a stable condition. The coal seam mined, the type of roof rock, and the gradation of the refuse influence the degree of compaction obtainable and the permeability of refuse. The shear strength of coal refuse appears to be controlled by its composition, moisture content, degree of compaction, amount and grain size of fines present. This investigation demonstrated these em¬bankments should not be treated as pure state-of-the-art dams; consideration must be given to the particular properties of coal refuse and the total refuse disposal system. Refuse dim slurry impoundments generally lack the site se- lection phase that is standard practice with siting most other types of dams.

Jan 1, 1974

By M. J. Hrebar

In the summer of 1990, a study was conducted to document large tractor (i.e., Caterpillar Dl1N) utilization in surface coal mining. The tractors were found to be utilized as primary production machines and in combination systems with blast casting and draglines and blast casting and excavator/truck systems. In addition, dozers were used to prebench ahead of a primary dragline system. The study also established ranges and averages for Dl1N operating costs and mechanical availability. Based on simulated production of various tractor dozing applications, the potential for low cost coal stripping was suggested (Hrebar, 1991). A follow-up study, also funded by Caterpillar Inc., was conducted in the summer of 1991 to determine actual production rates in two dozer stripping applications. These actual production rates would then serve as a foundation for estimates of stripping costs. This paper presents the results of the studies in a contour and a cast application.

Jan 1, 1992

By Gordon I. McPhail, John D. Nelson

Tailings management represents a major portion of the cost associated with extraction of gold. For each gram of gold extracted, 150 to 200 kg of waste material is produced. Because of environmental concerns and unwillingness of society to accept environmental damage caused by poor waste management practices it has become essential to follow responsible and safe practices in tailings management. This paper presents general aspects of tailings management and discusses different techniques utilized. Characteristics of tailings and the effects that these have on stability and environmental aspects are discussed. The paper also discusses the effect of mine back-filling practices on the surface disposal of the remaining tailings fraction.

Jan 1, 1987

By George P. Tateosian

Merchants perform a number of functions in the copper market. As a major distribution arm of the copper industry, they secure scrap and other copper bearing materials for processing into usable refined shapes. These are ultimately sold to fabricators. Merchants ' hedging and arbitrage activities help keep values in proper relationship from product to product or region to region. Through these switching and trading operations, they optimize the flow of copper from mine to consumer. And finally, merchants act as a repository for copper units during times of surplus and a stockpile from which to draw during tines of shortage.

Jan 1, 1979

By Egons R. Podnieks, Wallace W. Roepke

Mining technology to utilize vital lunar resources will be required for any commitment to permanent lunar basing. Lunar mining must be viewed both as a major supporting element for space resource commercialization and for creation of human settlements on lunar and planetary surfaces to support long-range space exploration. The Apollo missions to the lunar surface and results from fundamental research on analogue lunar rocks by the Bureau of Mines, and others, have provided the initial data for developing lunar mining technology. The multi-disciplinary research projected in this paper outlines the scientific and engineering needs to realize the lunar mining goals.

Jan 1, 1990

By N. Duru, C. Nesbitt

During the cyanide leaching process, gold and silver ores that come from the transition zones, which typically contains low levels of sulfide, may produce one or more of the following reduced sulfur species: sulfide ( HS−), polysulfides ( Sn 2−), thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−), pentathionate ( S5O6 2−), hexathionate ( S6O6 2−). The actual speciation of the reduced sulfur species in the circuits will primarily depend on the redox potential, pH, cyanide levels, and existing sulfur species in recycled process water, as well as the presence of other reactive metal species. The development of an accurate analytical method for sulfur species in cyanide leaching units of gold ores where sulfur speciation occurs has an important role in explaining the metal recovery deviations. This study presents the speciation of sulfur species and the development of ion chromatography method to analyze reduced sulfur species thiocyanate ( SCN−), thiosulfate ( S2O3 2−), trithionate ( S3O6 2−), tetrathionate ( S4O6 2−) in cyanide leaching circuits for gold ores. The method developed has resulted in precise quantification of target sulfur species in leach solutions. Method development and validation results were illustrated on analytical graphs containing each species’ peak number, retention time (min), type, width (min), area (mAU*s), height (mAU), and area distribution (%) of the peak.

Mar 2, 2024

By Harrison R. Cooper

Approximately 40 concentrators throughout the world have successfully adopted computer control for flotation circuit operation since 1969. Successful use of flotation control, gaining up to 2% efficiencies, has largely derived from effective employment of on-stream slurry analyzers and integration of key measurement data through digital processors. Requirements for reliable measurement have also led to improved functional reliability in magnetic flow meters, pH, reagent feed, and other key elements. Methods used in computer control of flotation will be reviewed and variations in operating philosophies will be described with reference to the approaches taken to flotation automation.

Jan 1, 1979

By Robert Stefanko

The Federal Coal Mine Health and Safety Act of 1969 had far reaching effects upon many aspects of mining, ventilation being no exception. In this paper, good ventilation procedures are briefly reviewed, and attention is focused on the changes brought about by the new Act. By way of illustration the ventilation system for a typical Pittsburgh Block system is developed and the requirements of the fan determined. This is then solved by an available computer program, and the application is evaluated. Figure 1 represents a projected system for a coal property 1 by 3 miles in plan at a depth of 1000 feet with a coal thickness of 6 feet and desired daily tonnage of approximately 7200 tons on a two-shift basis. Only one half of the mine is shown (north area) with a mirror image mining arrangement to be developed concurrently for the south area. Six working units are projected, three in each area, one on pillar extraction, another developing panel entries and a third on main entry development. A two-split system is used for each working section so that the continuous miner and bolting crews each have a separate split of air, and no equipment need pass through a line brattice. The old requirement of 6000 cfm at the last open crosscut has been increased to 9000 cfm, and for the first time a minimum quantity (3000 cfm) is stipulated at the face thus requiring either line brattice or an auxiliary fan. With the respirable dust requirement limited to 3 mg/m3, the use of a blower system is precluded and exhaust systems are virtually the only choice. Maintaining the line brattice within 10 feet of the working face at all times as required by the new law has a definite effect on the mining cycle and is most difficult at best. In the highly gaseous Pittsburgh seam located in south-western Pennsylvania and northern West Virginia quantities of 20,000 cfm per split are not uncommon to maintain the methane percentage below the required l%

Jan 1, 1972

By Luttrell. G.

The profitability of coal mining operations is highly dependent on the performance of the coal blending and processing facilities. Many companies have recognized this fact and have instituted optimization programs that require large amounts of coal characterization data, extensive operational information and complex costing models. Unfortunately, this brute force approach to optimization is often overwhelming in terms of time and cost and is generally too inaccurate to be of value in day-to-day field operations. A simpler and more practical approach involves the use of ?micro-price? optimization throughout the coal supply chain. This fundamental concept assigns unit values to each type product (particle or groups of particles) passing through the production units. True optimization occurs whenever all particles with positive worth are recovered and passed to market, while all particles with negative worth are rejected. This paper describes the fundamental workings of the micro-price concept as applied to coal blending and processing operations. Several examples are also included to demonstrate the economic gains that can be realized via the application of this concept.

Feb 23, 2014

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By N. Dashbold, E. Rudnik

"Waste electric and electronic equipment currently comprises the fastest-growing waste stream in the world, but at the same time it is seen as an important source of metals for the recycling industry. E-waste is usually treated pyrometallurgically, with hydrometallurgical methods used to a lesser extent. This paper reports the results of research on the selective recovery of copper from smelted low-value electronic waste. Pyrometallurgical pretreatment of the scrap allowed the removal of plastics and the increase of metal content in the material. The obtained alloy of copper, zinc, tin and silver was a multiphase solid consisting of two brass phases and inclusions rich in iron, lead and silver. Copper alloy was further anodically dissolved in ammoniacal chloride solution. It resulted in high degradation of the material and accumulation of the metals mainly in the slime. The slime was then leached in acid or ammoniacal chloride and sulfate solutions followed by selective copper electrowinning. Hydrochloric acid was the most efficient solvent for the slime, but ammoniacal solutions were more selective for copper. Copper could be leached with 96 to 100 percent and 87 percent efficiency from the slime by the chloride and sulfate solutions, respectively. Copper with 90 to 99 percent purity at current efficiency of 42 to 76 percent was obtained from the acid solutions, while copper with 98 to 99 percent purity at current efficiency of 60 to 86 percent was deposited from the ammoniacal baths. IntroductionObsolete electrical and electronic equipment makes up the fastest-growing waste stream in the world (Baldé et al., 2015), due not only to the introduction of wider ranges of new types and models of a variety of electronic products but also to the shortening of their life-spans, sometimes referred to as planned obsolescence by producers (Keeble, 2013). About 42 million tons of electronic waste, or e-waste, are estimated to have been generated globally in 2014 (Baldé et al., 2015), and it is expected that in the European Union alone the waste electrical and electronic equipment (WEEE) stream will reach more than 12 million tons by 2020 (European Commission, 2015). Accurate evaluation of e-waste generation (Wang et al., 2013) and its global transport (Breivik et al., 2014) is difficult, mainly due to a lack of high-quality data related to its market and socio-economic dynamics.Many countries introduced legislation to control e-waste flow, collection and recycling. For example, Directive 2012/19/EU on waste electrical and electronic equipment (European Parliament and the Council of the European Union, 2012) obliges all E.U. members from 2016 to maintain a minimum collection rate of 45 percent of the total weight of WEEE collected. From 2019, the minimum collection rate to be achieved annually shall be 65 percent of the average weight of electronics placed on the domestic market in the three preceding years, or alternatively 85 percent of WEEE generated in the territory of the particular member."

Jan 1, 2017

By Nelson R. Shaffer

Biotechnology has become a household word of the nineties, and it is expected to become as important in the next century as the computer is in the present. Numerous books and articles portray biotechnology developments as nothing less than a scientific revolution. Almost everywhere one looks new biotechnical breakthroughs are being reported that offer almost limitless opportunities to harness the force of living things to produce materials and manipulate their properties. Biotechnology has been broadly defined as any applications of biological organisms, systems, or processes to manufacturing and service industries. This seemingly new technology is, in fact, one of mankind's oldest scientific activities (Table l), which has been recently revolutionized by techniques of genetic engineering that arose out of basic research in biology, biochemistry, genetics, and information sciences. From fields as old as agriculture and medicine to those as new as monoclonal anti-bodies, transgenic plants, or biocomputers are encompassed by biotechnology. Like most human endeavors, industrial minerals play critical roles in biotechnology. In addition biotechnology holds real potential to improve extraction and beneficiation of certain industrial minerals themselves. BIOTECHNOLOGY OVERVIEW Companies using established biotechnical techniques make up large and diverse groups such as agriculture, chemicals, and pharmaceuticals. The massive US Pharmacopia (Anon., 1990a) provides detailed specifications for minerals used in medicines. Alumina, zirconia, apatite, and bioactive glass have seen service as implant materials (Williams, 1990) and new uses for minerals in health sciences are being actively researched. Agriculture produced $361 billion worth of food and drink during 1991 in the United States; organic chemicals, pharmaceuticals, and enzymes accounted for $68, $59, and $42 billion, respectively (Anon., 1992a). It is not possible to separate the contributions of industrial minerals to biotechnical products, but they represent a very large and rapidly growing new field of uses. The new biotechnology has nearly 300 small companies, plus 15 established companies with 742 biotechnology-related firms (Dibner, 1991b). Revenues exceeded $2 billion in 1990 and are expected to grow to $50 billion by 2000 (Anon., 1992c), with worldwide sales exceeding $100 billion (Burrill and Roberts, 1992). Federal research amounted to $3.4 billion in 1990 (Anon., 1992b). The United States is the world leader in biotechnology, but other countries have large, well-funded programs. Despite debate about safety, obstacles to new biotechnology products are declining (Embers, 1992, Gibbons, 1991). Fifteen biotechnology drugs valued at $1.2 billion (Thayer, 1991a) are on the market, and more than 100 are in various stages of testing (Edington, 1992). Many diagnostic tests are also in use or development (Demain, 1983, Anon., 1992). Large scale efforts to produce or transform important chemicals are also underway (Ng et al., 1983, Hinman, 1991), and research into geologic uses of biotechnology has begun. Much has been published about microbial mining, oil recovery, desulfurization, bioremediation, and other geologic aspects of biotechnology, but this chapter is the first attempt to explore interactions of biotechnology and industrial minerals. This chapter examines uses of minerals in biotechnology; how biotechnology can be used to discover, recover, and beneficiate industrial minerals; and speculates on some potential, but as yet untried uses. Definitions What exactly does the word biotechnology mean? Bud (1989) states that the first use of the term was by Karl Ereky in 1919 to cover the interaction of biology and technology, and in 1933 the term was used in Nature. After citing seven different definitions, Smith (1988) concludes that biotechnology is a series of enabling technologies involving practical applications of organisms or their subcellular components to manufacturing and service industries or to environmental management. Walker and Cox (1988) suggest a definition of "the practical applications of biological systems to the manufacturing and service industries and to the management of the environment." Primrose (1991) says that it is "the commercial exploitation of living organisms or their components." There is essentially an older broad use of the term and a new use. The US Office of Technology Assessment (Anon., 1984) uses a broad definition that includes any technique that uses living organisms (or parts of organisms) to make or modify products, to improve plants or animals, or to develop micro-organisms for specific uses. Definitions are different, but they all have several fundamental elements that include the control, management, or manipulation of living things for commercial, industrial, or useful ends. While such a definition encompasses all of agriculture in practice the "new" biotechnology is restricted to processes involving microorganisms-plant and animal cells, or enzymes. Many consider biotechnology to be recent, but it is one of our oldest technologies as evidenced by the prehistoric origin of brewing, cheese-making, and other techniques. [Table 1] gives some of the important developments in the history of biotechnology. Smith (1988) breaks down historical developments of biotechnology into four phases: 1) prehistoric with no understanding of underlying processes; 2) nonsterile processes; 3) sterile processes after 1940; and 4) genetic and recombinant DNA technology deliberate design of special organisms or processes.

Jan 1, 1994