Search Documents

By Basar Arioglu, Jaeung Kim, Mehmet Öztürk, Jinmoo Lee, Dongho Lee, Taek-Kon Kim

"Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) includes 3.34 km of a bored double-deck tunnel under the Bosphorus Strait, at a maximum depth of 106 m from the sea level, and 1 km of twin NATM tunnels on the Asian side. The region’s variable geology, hydrology and propensity for seismic activity, combined with high water pressure and large-diameter/double-deck tunnel configuration, make the Eurasia Tunnel one of today’s most challenging and complex projects under construction. Due to the site’s proximity to the active North Anatolian Fault, the tunnel is designed to withstand a 7.5 magnitude earthquake. The tunnel penetrates through both the Trakya bedrock (on both European and Asian sides) and the alluvial sediments at the bottom of the channel. The tunnel is designed to accommodate differential displacements by introducing seismic/flexible joints at proper locations at the transition zones between rock and soft soils. Tunnel fire is also a significant design consideration for undersea tunnel due to that the rubber protecting it in close proximity of the seismic joint should resist a fire for long term safety and durability. This paper mainly focuses on the design for method of tunnel response analysis in transverse and longitudinal direction against seismic demands relating with the seismic joints. INTRODUCTION Istanbul Strait Road Tube Crossing Project (Eurasia Tunnel) will build and operate a roadway tunnel under the Borphorus connecting Kazlicesme on the European side and Goztepe on the Asian side, to provide additional road-access across the Strait and consist of three main parts as shown in Figure 1."

Jan 1, 2016

By M. C. Rockwell

There are about 1.8 Mt (2 million st) of discarded dolomitic-limestone tailings from the Gays River lead/zinc mining operation in Nova Scotia currently stockpiled in a tailings pond at the mill site. Neutralization effectiveness similar to an agricultural grade limestone and low contents of residual metals make the tailings a potential source of soil conditioner material for the local market. However, the fine particle size, 98% passing 147 pm (about 100 mesh), and a moisture content of 20% make their handling, shipping, and application to soils difficult. The tailings were agglomerated into small hard pellets with various amounts of soil nutrients, moisture content less than 13%, and pH values ranging from 6.5 to 8.7.

Jan 1, 1987

By D. Lee Petersen, Charles R. Nelson, Marvin Marshak

INTRODUCTION Construction is underway on a laboratory cavern 713 m below surface at the Soudan Mine, Tower-Soudan State Park, in northeastern Minnesota. The 13.9 in wide by 11.6 m high by 71.8 in long cavern will provide a laboratory space for basic research in physics, in which experiments can be conducted with greatly reduced interference from cosmic radiation. A first generation experiment, called the Soudan 1 detector, is currently operating in a converted drift 591 in below surface at the mine. The initial phase of the Soudan 2 detector will be an 1100-metric ton unit, which will occupy approximately a 19 m length of the cavern. Control and monitoring equipment will be in a prefabricated shop office enclosure erected in the cavern. The location and planned usage for the laboratory cavern present special excavation, lining, and outfitting requirements. Temperature and humidity control, a relatively clean dust-free environment, and a long service life are required. Low cost and risk to the owner were basic requirements due to the nature of the funding. The most common type of site selected to meet these two constraints is either an operational mine or a civil works facility such as a road tunnel. There are often serious problems for such laboratories because of ongoing operations such as blasting, hauling, etc. Most of these problems do not exist for the Soudan 2 laboratory because the mine is used as a historical site with regular tours only in the summer season. The laboratory owner, the University of Minnesota, and the park owner, Minnesota Department of Natural Resources, are both public agencies of the

Jan 1, 1985

By A. E. Hall, K. R. Mutama

The wind tunnel has been used extensively for mine ventilation research and continues to be a valuable tool. The advent of the powerful personal computer has reduced the use of wind tunnels because several flow problems car be simulated and investigated quickly. This paper describes the recent design and construction of a wind tunnel which is now being used for mine ventilation aerodynamic research and teaching purposes. The wind tunnel has a square cross section measuring 900 by 900 mm and is 8485 mm long from the entrance to where it joins the fan. The tunnel was designed as an open circuit suction type and is attached to a 7.5 kW variable pitch axial flow fan capable of producing over 6 m3/s of airflow. The entire length of the wind tunnel can be used for flow investigations and all activities are visible since the sides are made of plexiglass. Results are presented from the test program to show that even without honeycombs and screens air flow symmetry is achieved.

Jan 1, 1993

By J. O. Marsden

The 1980s saw a revolution in gold extraction technology, paralleled only by the implementation of the cyanide leaching process in the late 1800s. This revolution was led by the widespread adoption of carbon adsorption processes for gold recovery, heap leaching of low-grade ores and development of a variety of oxidation processes to treat refractory ores. In the late 1980s, gold production in almost all regions of the world increased, with the notable exception of South Africa. This geographical variety is creating a greater diversity of challenges for gold metallurgists. This is due to a wider range of ore types, new and varied environmental regulations and legislation, and a requirement to select the most appropriate technology to suit local needs. North America has led this technological revolution in the gold industry and is responsible for commercialization of most of the major innovations: carbon-in-pulp, heap leaching, whole ore pressure oxidation and whole ore roasting. Process selection trends A general trend in precious metals extraction technology has been the treatment of ores with progressively lower grades. The lowest cost treatment, dump leaching of material at run-of-mine size, has been increasingly applied. ZortmanLandusky, in Montana, is successfully leaching material above a cutoff grade of 0.2 g/t (0.006 oz/st) at an average rate of about 28 kt/d (31,000 stpd). At this scale of operation and in the absence of any cyanide-consuming species in the ore, process operating costs for a ge¬neric run-of-mine leaching operation are estimated to be between 60 and 75 cents/ t (66 and 77 cents/st). One of the largest heap leach opera¬tions treating crushed ore is the Round Mountain Mine in Nevada. It processes about 45 kt/d (49,000 stpd) at an average grade of 1.1 g/t (0.032 oz/st) at a nomi¬nal crush size of 80% -19 mm (-0.7 in.). Round Mountain also treats lower grade ore above a 0.2 g/t (0.006 oz/st) cutoff by dump leaching at run-of-mine size.

Jan 1, 1993

By D. W. Park

Geologic condition is one of the most important factors for longwall mining operations, especially, the existence of faults limits the mineable area, or cause stress variations at the longwall face. Recently, a longwall panel passed through a fault at the Shoal Creek Mine of Drummond Company, Inc. The fault was situated diagonally along the longwall face and the coal seam was displaced up to 2.4 m (8.0 ft) in a mode of a normal fault. LoSCoMS (Longwall Strata Control and Maintenance System) was used for monitoring shield pressure every minute and interpreting data in terms of setting, developing and final pressures. The results of the analysis regarding the influence of the fault on the shield pressure are presented.

Jan 1, 1999

By S. C. Sun

The grinding of coals for coal preparation has been studied extensively by previous investigators, but no similar work has been done on coal lithotypes (l-4). However, the different natural breakage characteristics of coal lithotypes have been recognized and utilized by the coal industry (5,6) to develop the Longway Burstlein process (7) for the concentration of macerals(8). The specific objective of this research was to determine the relative grindability of lithotypes, obtained from both anthracite and bituminous coals. An attempt was made to relate the findings, wherever possible, to the chemical and physical properties of the tested lithotypes. Another aspect of this research was to ascertain the size distribution and grindability of lithotypes ground at a various number of revolutions in a Hardgrove mill.

Jan 1, 1970

By J. W. Furlan

Due to the time consuming nature of froth testing in a laboratory environment, it is required, due to practical limitations, to develop a method of applying a single set of performance test data (Visintainer & Whitlock, 2012) obtained for a single froth pump at a given speed, to a range of froth pump speeds and sizes, % air contents, and liquid viscosities. Head, efficiency, and flow all vary as functions of both liquid viscosity and air content. As such, it is necessary to develop a technique which can be used to interpolate from existing test data in order to predict froth pump performance for pumps of various sizes running at variable speeds. Details of the technique developed in order to achieve this goal as well as the insights gained from analysis of the resulting regressions are discussed. Additionally, comparisons are made between the performance predictions of this test-derived method and those of the Hydraulic Institute Standard for the effects of liquid viscosity on centrifugal pump performance (ANSI/HI 9.6.7-2010).

Feb 27, 2013

By L. Yuan, A. Smith

"NIOSH’s mine fire simulation program, MFIRE, is widely accepted as a standard for assessing and predicting the impact of a fire on the mine ventilation system and the spread of fire contaminants in coal and metal/nonmetal mines, which has been used by U.S. and international companies to simulate fires for planning and response purposes. MFIRE is a dynamic, transient-state, mine ventilation network simulation program that performs normal planning calculations. It can also be used to analyze ventilation networks under thermal and mechanical influence such as changes in ventilation parameters, external influences such as changes in temperature, and internal influences such as a fire. The program output can be used to analyze the effects of these influences on the ventilation system. Since its original development by Michigan Technological University for the Bureau of Mines in the 1970s, several updates have been released over the years. In 2012, NIOSH completed a major redesign and restructuring of the program with the release of MFIRE 3.0. MFIRE’s outdated FORTRAN programming language was replaced with an object-oriented C++ language and packaged into a dynamic link library (DLL). However, the MFIRE 3.0 release made no attempt to change or improve the fire modeling algorithms inherited from its previous version, MFIRE 2.20. This paper reports on improvements that have been made to the fire modeling capabilities of MFIRE 3.0 since its release. These improvements include the addition of fire source models of the t-squared fire and heat release rate curve data file, the addition of a moving fire source for conveyor belt fire simulations, improvement of the fire location algorithm, and the identification and prediction of smoke rollback phenomena. All the improvements discussed in this paper will be termed as MFIRE 3.1 and released by NIOSH in the near future INTRODUCTION The MFIRE program, originally developed in the 1970s by the U.S. Bureau of Mines (now the Office of Mine Safety and Health Research (OMSHR) at the National Institute for Occupational Safety and Health (NIOSH)) and Michigan Technological University, has been a mainstay in modeling of the mutual influences between a fire and the mine ventilation system during an underground mine fire. Several update versions have been released over the years, including MFIRE 1.27, 1.29, 1.30, 2.0/2.01, 2.10, and 2.20. The MFIRE program logically comprises four parts: (1) a conventional network calculation, where it performs the basic network balancing without considering heat or mass transfer; (2) a temperature calculation to establish the reference temperature distribution before a non-steady state (transient-state) simulation; (3) a transient-state simulation that follows changes in ventilation step-by-step to produce a continuous description of the temperature distribution, smoke, and contaminant spread through the ventilation system during a fire event; and (4) a quasi-equilibrium simulation to predict the state of the ventilation system after a relatively long period of time (defaulted as 5 hours in MFIRE) as the fire reaches a quasi-steady state. In summary, MFIRE is a computer simulation program that performs normal ventilation network planning calculations and dynamic transient-state simulation of ventilation networks under a variety of conditions including the influence of natural ventilation, fans, fires, or any combination of these (Chang et al., 1990)."

Jan 1, 2016

By J. Hanna

The University of Alabama Mineral Resources Institute (MRI) has developed a unique process for selective fatty acid flotation of carbon-ate gangue from sedimentary apatites "francolite" in the pH range of 4-6 without collector conditioning of the pulp. The process, which does not require an apatite depressant, was modified to beneficiate a high Mgo siliceous phosphate matrix from south Florida. The modified process includes two flotation stages, one for carbonate removal, as mentioned above, and the other for phosphate recovery from the siliceous gangue. The selective flotation separation of the carbonate and phosphate, from siliceous constituents of the matrix at various pH levels and collector dosages are discussed. In the carbonate flotation stage, about 70% of the Mgo was rejected in the froth and the phosphate flotation stage produced concentrates analyzing about 31% P2O5,0.7% HgO and 4% insol. The overall P2O5 recovery in the two stages is about 85%.

Jan 1, 1989

By J. A. Boyle

In the Frick District of U, So Steel Corporation, we have had more than 37 years of experience in the use of multiple-fan ventilation systems, in our coal mines. In our Colonial field, with a long belt installation, we have mined 85 million tons of coal with the use of the multiple fan system of ventilation. In our Palmer field, with the use of the same arrangement, we have mined 90 million tons of coal--a total of 175 million tons without one accident attributable to improper mine ventilation. The same system, fundamentally, has been installed in our expanding Robena operations and at its present stage of development we are using eight fans to ventilate this area. To date we have mined 55 million tons of coal with very encouraging results and again without any accidents attributable to ventilation.

Jan 1, 1961

By G. M. Wilemon

The U.S. Bureau of Mines has conducted investigations on extracting phosphate values from wastes generated during the mining and beneficiation of phosphate matrix. These wastes may contain up to one third of the phosphate originally present in untreated ore. Samples of wastes were air-dried and leached using 93 pct sulfuric acid in the presence of methanol. Evidence for the formation of a calcium sulfate hemihydrate coating that hinders complete dissolution of phosphate is presented. Solid-liquid separations were enhanced when flocculation was effected using poly(ethylene oxide) (PEO) in conjunction with hydroxypropyl cellulose (HPC) or hydroxyethyl cellulose (HEC. A conceptual flowsheet for a proposed process using an acid-alcohol leaching technique is presented.

Jan 1, 1990

By Wilbur H. Smith

Geologic mapping techniques at the Bingham Mine have evolved as rapidly expanding applications of geological data have caused new methods to be utilized. The most significant changes in method have been in the preparation of the base map and in computer application of collected data. Formerly maps were prepared by surveying with transit or plane table. Currently a photogrammetric map, on the scale of 1-inch equals 200-feet, is prepared semi-annually and continuously updated to keep pace with the removal of more than 350,000 tons of material daily. Larger scale bases for specific problems, such as areas having unstable slopes, are prepared by use of aerial and terrestial photography and photo mosaics. Note sheets designed for computer application enable fast processing of the data. Application of geology at the Bingham Mine has been increasing rapidly in recent years. The effect of structure, rock type, and alteration on slope stability, the relationship of sulfide mineral distribution to concentrating results, the effect of rock and mineral types on waste dump leaching, and requirements of a reliable internal source of silica flux for smelting are a few of the problems which require the collection and application of geologic data.

Jan 1, 1968

By G. D. Bates

INTRODUCTION The Magmont mine is a joint venture of Cominco American Inc. (operator) and Dresser Minerals, Inc. The mine-mill operation is located approximately 160 km (100 miles) southwest of St. Louis, MO, in what is commonly referred to as the "Viburnum Trend.” The Magmont mine is designed for a production rate of 3810.2 t/d (4200 stpd) on a 5-day week, three shifts per day basis. Initial production began in 1968. The mine is open stope, room-and-pillar, and essentially horizontal along the trend of the ore body. Briefly, the main geological structure can be described as a brecciated graben bounded by reverse faults. The ore body in cross section is shaped like a bell curve with some lateral extension at the lower part. Presently outlined ore is 609.6 to 762 m (2000 to 2500 ft) in width and 2133.6 m (7000 ft) in length. The ore varies in thickness from 4.87 m (16 ft) on the fringes to an average of 27 m (90 ft) in the high ore areas bounded by the reverse faults. Lead is the primary metal with zinc and copper secondary. MINE DESIGN The basic design of open stope, room-and-pillar mines has been described by several writers and need not be repeated here. (Anon., 1970; Bullock, 1973; Casteel, 1972; Christiansen et a]., 1970; and Lane, 1964) This discussion covers the mining sequence as applied to the particular problems at the Magmont mine, the use of equipment, and deployment of the work force. In the upper portion of the Magmont ore body is a layer locally called the False Davis shale. This layer lies below the true Davis shale, is normally interbedded with dolomite, is of varying thickness, and if mineralized, is included in the top pass of the mining sequence. In thick ore areas this layer will be 2.13 to 2.43 m (7 to 8 ft) in thickness and will occur in the upper portion of the pillars. Due to its incompetency the presence of this False Davis layer is of primary concern in mine planning and operation. Mining areas are divided into three basic groups by ore thickness. First are areas of ore up to 6.09 m (20 ft) in thickness. These areas are below the False Davis shale and are mined single pass with drill jumbo. Second are those areas up 13.71 to 15.24 m (45 to 50 ft) in height. The first 4.87-111 (16-ft) Pass is taken at the top of the ore and the back and pillars secured. Benching the lower portion(s) in 4.57 to 4.87-m (15 to 16-ft) passes is then done with either a drill jumbo drilling horizontally or a crawler drill drilling vertically. Normally these areas are below the Table 1. Productivities per Manshift False Davis shale. These areas may also be mined by back slashing, or overhand benching, where the first 4.87-m (16-ft) pass is taken at the base of the ore and successive 4.87- m (16-ft) passes are taken upward. A minimum amount of back slashing is done at Magmont since it requires repetition of roof control on each pass and roof control is the single largest stoping cost at Magmont. Ore left to provide a working platform oxidizes and is coated by oil spills thus reducing metallurgical recoveries. The third mining area is over 15.24 m (50 ft) in height UP to a maximum of 40.23 m (132 ft) and will encompass the False Davis shale. These areas are mined by first driving +15% inclines to the top of the ore body. The top pass is mined and the back is bolted and roof mats installed as a matter of standard practice to minimize roof problems as mining progresses downward. Once the back and pillars on the top pass are secured, benching begins on successive passes with either the drill jumbo or crawler drill. Pillars on all successive passes below the top pass are secured as necessary. While benching progresses below the top pass, the pass at the base of the ore body is mined leaving a sill of 4.57 to 7.62 m (15 to 25 ft) in thickness to be removed with the crawler drill in a retreating manner. Rooms are mined on a 1.57 rad (90") grid pattern to insure alignment of pillars where multiple passes are taken. Pillars are designed on a 17.98-m (59-ft) spacing with rooms up to 10.66 m (35 ft) in width. Heading widths are wide enough for the mobile equipment to turn without additional allowance for curves. The result is a flexible layout which provides a maximum number of headings available for high extraction rates and grade control. PRODUCTION Incentive Bonus Incentive bonuses play an important part in the mine production at Magmont. Production crews are trained to perform only one of the mining functions of drilling, blasting, mucking. or roof bolting. This specialization, or functionalization, is augmented by development to open all possible stoping areas as early as possible in the life of the mine. This insures that each crew will have enough headings to perform its specialty. The incentive bonuses increase exponentially as output increases. The lucrative incentive bonus coupled with the specialization of the production crews and proper mine development have combined to give the high productivities shown in Table 1. Development crews perform all mining functions in their area. The incentive bonus is paid on a per foot basis, Crews on different shifts working the same heading share equally in the bonus proportional to their contract hours worked.

Jan 1, 1982

By Paul C. Schmall

In recent years, several geotechnical methods have been successfully applied to ash pond closure. These include modified dewatering techniques with wellpoints and wells to physically drain the material, soil mixing to create a soil-concrete material for improved accessways as well as improved ground structures within ponds to act as barriers or gravity dams, and geotechnical instrumentation to serve as an early warning of the potential for liquefaction. Given the parallels between fly ash and sluiced in place mine tailings, the application of fly ash remediation method to mine tailings shows significant potential, as illustrated in this paper.

Feb 1, 2024

By T. M. Barton

Coal mine bumps the violent failures of over-stressed coal', present a safety hazard to miners when mining is conducted in deep, bump prone coal mines. Two different longwall gate entry systems were evaluated in a Southern Appalachian coal mine located in the Pocahontas No. 3 Coalbed under approximately 610 m of overburden which included a massive sandstone member. Both gate entry systems employed a center abutment pillar flanked by yield pillars. The original design employed a 24.4 m square abutment pillar' while the new design employed a 36.6 by 54.9 m' abutment pillar. Rock mechanics instrumentation data analysis and in-mine observations indicated that this increase in abutment pillar size significantly decreased bump potential. The new design in worse case conditions increased effective bearing area 62 pct with only a 9 pct increase in gate entry system width and eliminated face bumps that wer7 experienced with the original gate entry design.

Jan 1, 1991

By N. L. Wesis

General History The first jaw crusher in the US was patented about 1830, but the Blake crusher that has maintained a substantial advantage over other types was invented in 1858 by Eli Whitney Blake. For going on 150 years the jaw crusher has been an invaluable machine; even today, when gyratory crushers have assumed most of the burden of crushing large tonnages of large rock and ore, the jaw crusher has a firm place in the mining industry. It is interesting that soon after the invention of the Philetius Gates gyratory crusher in 1881, a contest between the first No. 2 Gates and Blake jaw crushers of equal gape showed the gyratory to be 3.2 times as fast. This foretold a day not far in the future when the jaw crusher would not be adequate on the largest jobs. In his Textbook of Ore Dressing (1909) R. H. Richards recom¬mended that the word breaker be used for all machines breaking to relatively large sizes (say to 5 in. or greater), and crusher be used for finer work. Even in the 1968 US Bureau of Mines dictionary of mining terms the work breaker is defined by Richards in this context. However, in modern US usage it is nearly limited to coal breaking. Over the years the jaw crusher has been developed in a variety of forms but it appears today in these three general forms: (I) Blake type, (2) Dodge type, and (3) single toggle (or overhead eccentric) type. All of these crushers have a fixed jaw and a moving jaw, between which the coarse rock fragments are intermittently caught and crushed. The three types are differentiated by the manner in which the movable jaw is moved in relation to the fixed. Types The Blake-type crusher is shown in cross section in Fig. 1. The simplicity and strength that have made it first among jaw crushers are evident. The movable jaw is suspended from a cross-shaft at its upper end, this shaft being carried in bearings on the sides of the frame. The actuating mechanism consists of an eccentric shaft, also supported in frame-mounted bearings, which imparts through a pit¬ man and a pair of toggles a reciprocating motion to the bottom of the swing jaw, the return movement being effected by several spring¬loaded rods. The whole is built into a box frame with the crushing chamber at one end. As in all jaw crushers, the eccentric shaft is equipped with a heavy flywheel that maintains an even speed through¬out each stroke. The Dodge-type crusher illustrated in Fig. 2 is simple, mechani¬cally. Its movable jaw, being pivoted below the discharge opening, has minimum movement at crusher discharge and maximum at crusher feed. Because the choke point coincides with the point of least motion, these crushers are of relatively low capacity, and the rapid action in the feed area gives the machine the advantages of large reduction ratio and closely sized product. Thus, it fits well into low-capacity operations like sample reduction. Besides low capacity, its principal disadvantages are tendency to pack and make fines. The single-toggle or overhead-eccentric type of jaw crusher (see Fig. 3) has gained in usage, starting as a modification of the Dodge idea in that the greatest movement of the movable jaw occurs at the top, and being gradually improved and strengthened to its position today where it covers just as wide a field of application as the Blake type from the standpoint of feed opening. The motion of the movable jaw is the result of the circular motion of the eccentric shaft at the top of the swing jaw combined with the rocking action imparted to the bottom by the inclined toggle plate. Because of light weight and mechanical simplicity, it is economical in small mills and portable plants where the rock is not as tough and abrasive as to punish the machine with excessive impact from shocks, or excessive wear result¬ing from the pronounced vertical component of motion.

Jan 1, 1985

By Takuya Tani, Tomoyuki Aoki, Kazuo Saskai

"The authors have proposed a unique methodology in the evaluation of rock mass stiffness for the range of five to twenty meters ahead of the tunnel face, with the use of small diameter inclinometers. The inclinometers are installed at the tunnel crown at a pre-determined constant interval, about one meter behind the face in order to obtain the slight change in inclination angles during tunnel excavation. This method was developed as a daily control measurement such that the geological condition and its possible change ahead of the face could be detected early by monitoring the trend of inclination angles. This paper describes the results of the ground stiffness ahead of the tunnel face evaluated at a mountain tunnel construction site. This stiffness is evaluated automatically and displayed visually by the current system equipped with a result display screen, together with a warning message against a weak zone when detected. 1. INTRODUCTION In a conventional planning of a mountain tunnel, according to the Japanese Standard (JSCE, 2006) seismic refraction surveys from the ground surface are performed and tunnel support patterns are then designed based on the seismic wave velocity. The resolution of the velocity profile estimated by this technique, however, is poor as the tunnel overburden becomes large. The tunnel face is therefore often encountered by unforeseeable fault zones or weak rocks. Such an unpredictable weak zone occasionally causes the collapse of the tunnel face. Clarifying the forward geological information during excavation is hence significant for safe and well-controlled construction. According to the geological conditions ahead of a face, auxiliary methods typified by forepiling and face bolting could be preliminarily prepared for prompt execution. For the purpose of acquiring forward geological information, pilot borehole drilling and seismic reflection methods represented by the TSP (Tunnel Seismic Prediction) or HSP (Horizontal Seismic Profiling) are often applied. Those exploration are carried out near the tunnel face for a couple of days. This often leads to the interruption of excavation procedure and has no small effect on the construction schedule. On the other hand, some forward ground prediction methods in the daily control measurement have been developed e.g. by Schubert et al. (1995). In this method, tunnel displacements in the direction of the tunnel axis are used together with the crown settlements. We have tested their method at a few of our tunnel projects and found difficulty in the evaluation of the forward ground condition due to insufficient resolution of the axial displacement measured by a total station theodolite that we usually use for the tunnel measurement. We have therefore developed a novel methodology of monitoring slight inclination at the tunnel crown near the face, so that the forward ground conditions can be predicted and evaluated as part of a routine measurement procedure."

Jan 1, 2016

By M. H. Kahn, F. C. Bond, K. J. Edmiston

Comminution of various materials can be achieved in grinding equipment by nipping, impact, attrition, or a combination of these actions. Pna mills also known as edgerunners, chasers, and mullers-are classified as a nipping machine. The essential features of this type of grinding machine are rollers or mullers that turn on a horizontal axis while rating on the bed of material in the pan. Ploughs are used to direct the unground material to the center of the pan. Grinding may be accomplished wet or dry. Aritres, Chilean mills, and Huntington mills are types of pan mills. Ring roll and ring Ml mills, another type of nipping machine, were developed for grinding smaller particles of intermediate hardness to product sizes of about 100 pm. They were designed to attempt to reduce the cost of similar size reduction in ball mills and have been widely used to pulverize coal for power-plant facilities. Impact Machines Grinding machines that can be classified as impact mills include: hammer, cage, centrifugal, vibratory, pin, and stamp mills. The distinctive feature of an impact mill is that it has a fast-moving part that transfers some of its kinetic energy to the material particles by direct contact so that internal stresses are created in the particles. The Reitz Disintegrator is an example of an impact mill. It has rigidly mounted hammers attached to a vertical shaft that rotates in close proximity to horizontally mounted screens. The feed pulp enters parallel to the vertical shaft, and may have a solids content of from 40

Jan 1, 1985

By Son Hoang Nguyen, Thanh‑Hai Pham, Duoc Van Tran, Dung Thi Kim Nhu

Apatite ore plays a critical and irreplaceable role in fertilizer production and is being upgraded in quality in northern Vietnam. The old tailing of the Bac Nhac Son beneficiation plant (Vietnam) has a significant apatite amount in the form of coarse unliberated particles. These millions of tons of tailing ore have 6–8% of P2O5 content, which can be retreated to provide fertilizer factories. This work presents the results obtained in recovering apatite from this tailing in the laboratory. By the combination of the processes of classification, preliminary flotation, re-grinding and cleaning in the flotation column, an apatite concentrate of 30.68% P2O5 can be obtained with the total recovery of 37.76% from the initial tailing of 7.56% P2O5. The study results not only provide an appropriate technical solution for recovering the apatite ore from tailing ore but also have outstanding meaningness in the recovery of mineral resources under the context of a circular economy.

May 24, 2023